Effects of Some Solid Lubricants Suspended in Oil Toward Controlling the Wear Performance of a Cast Iron

2010 ◽  
Vol 132 (4) ◽  
Author(s):  
B. K. Prasad ◽  
S. Rathod ◽  
M. S. Yadav ◽  
O. P. Modi
Keyword(s):  
Cast Iron ◽  
Wear Rate ◽  
Solid Lubricant ◽  
Frictional Heating ◽  
Applied Pressure ◽  
Solid Lubricants ◽  
Specific Response ◽  
Test Environment ◽  
Wear Performance ◽  
Wear Response

The present investigation deals with the examination of the sliding wear response of a gray cast iron in oil lubricated condition over a range of applied pressure. The composition of the oil lubricant was changed by adding 5.26 wt % solid lubricant particles. The solid lubricants used were graphite, talc, MoS2, and lead. The observed wear response of the samples has been substantiated through the characteristics of wear surfaces, subsurface regions, and debris particles and discussed in terms of specific response of different microconstituents, such as ferrite, pearlite, and graphite present therein. Operating wear mechanisms were assessed through the observed features of wear surfaces, subsurface regions, and debris. The wear rate increased with applied pressure. The slope of the wear rate versus pressure plots was low up to a critical pressure. This was followed by a sudden rise in the slope at higher pressures irrespective of the test environment. The frictional heating was affected by pressure in a manner practically identical to that of the wear rate. The presence of graphite, MoS2, and lead in the oil led to a substantial decrease in the wear rate and severity of frictional heating. The oil plus lead lubricant mixture was observed to offer best results in terms of reduced wear rate and lower frictional heating. This was followed by the ones containing graphite and MoS2 while talc caused the wear performance of the samples to deteriorate over that of the bare oil. However, the severity of frictional heating decreased in general in the oil containing solid lubricant particles. Seizure brought about high frictional heating and wear rate.

Sliding wear characteristics of grey cast iron as affected by the type and fraction of solid lubricants in oil

2014 ◽  
Vol 66 (5) ◽  
pp. 569-578
Author(s):  
B.K. Prasad
Keyword(s):  
Cast Iron ◽  
Wear Rate ◽  
Sliding Wear ◽  
Frictional Heating ◽  
Solid Lubricants ◽  
Grey Cast Iron ◽  
Wear Behaviour ◽  
Specific Response ◽  
Content Type ◽  
Grey Cast

Purpose – The purpose of the paper is to assess the influence of the volume fraction solid lubricants like talc lead and graphite in oil separately and in combination towards controlling the sliding wear behaviour of a grey cast iron and understand the factors controlling the response of the material in a given set of experimental conditions. Design/methodology/approach – The composition of the lubricating medium (oil) has been changed by dispersing 5 per cent graphite, talc and lead particles separately and in combination. Sliding wear tests were conducted on grey cast iron samples over a range of applied pressures. Parameters determined were wear rate and frictional heating. The wear behaviour of the samples was further substantiated through the features of wear surfaces, subsurface regions and debris particles. Material removal mechanisms and factors responsible for a specific response of the samples have also been analysed. Findings – The wear rate increased with increasing applied pressure. Addition of graphite and lead to the oil separately or in combination brought about a reduction in the wear rate of the samples; talc and talc + lead produced a reverse trend. Temperature near the specimen surface increased with test duration and applied pressure. The test environment influenced the frictional heating in a manner similar to that of the wear rate. Adhesion and abrasion were observed to be the operating material removal mechanisms. Smearing of the solid lubricating phase and delamination resulting from cracking tendency also controlled the wear response. Research limitations/implications – Oil is a very popular lubricant used in engineering applications involving friction and wear. Solid lubricants are used along with the oil. The nature, characteristics and content of the solid lubricants very much control the performance. Limited information is available pertaining to assessing the influence of the type and fraction of solid lubricants in the oil towards controlling the wear behaviour of cast irons (popularly known tribomaterials). The present study enables to understand the effectiveness of talc, lead and graphite in oil towards governing the wear characteristics of cast iron and analyse wear mechanisms and controlling parameters. Practical implications – Graphite and talc are available in nature in abundance. Graphite is a popularly known solid lubricant, while talc is less explored. Lead is also well-known as a solid lubricant but poses health hazard in practice due to its toxic nature. The present study explores the lubricating capability of talc when mixed with oil separately or in combination with lead and graphite towards controlling the wear response of a grey cast iron. It enables to understand the factors responsible for the specific response of talc. Social implications – Assessment of the lubricating potential of talc as a possible substitute to lead is important in view of the toxic nature of the latter. If successful, the exercise could enable to replace lead with talc. Originality/value – The present manuscript is an original piece of the author's research work.

scholarly journals Development of Highly Hydrogenated DLC Coatings for Solid Lubricant Applications in Space

2005 ◽  
Author(s):  
A. Vanhulsel ◽  
R. Jacobs ◽  
K. Van Acker ◽  
E. Roberts ◽  
F. Velasco ◽  
...  
Keyword(s):  
Wear Rate ◽  
Friction And Wear ◽  
Applied Load ◽  
Solid Lubricant ◽  
Solid Lubricants ◽  
Ambient Atmosphere ◽  
Test Environment ◽  
Load Range ◽  
Dlc Coatings ◽  
Aisi 52100 Steel

The development of advanced solid lubricants is of considerable importance to space tribology. The most common solid lubricant coatings today are based on MoS2, lead or PTFE. However, none of these coatings can simultaneously fulfill all specifications, with regard to friction and wear, under ambient atmosphere and in vacuum. Consequently research is currently being aimed at further improvements in advanced solid lubricant coatings. One approach is to optimize Diamond Like Carbon (DLC) coatings to meet the specifications. In this study, the feasibility of highly hydrogenated DLC coatings (∼ 50 at% hydrogen) for solid lubricant applications is assessed. The coatings were deposited on AISI 52100 steel substrates and tested in ball-on-disc tribometers in air, vacuum and dry nitrogen environments. It was found that the test environment has the most decisive effect on both friction and wear rate, while these parameters are only slightly affected by varying the applied load under a given atmosphere. It was concluded that highly hydrogenated DLC coatings are capable of yielding ultra-low friction values in vacuum (μ = 0.008). The average friction coefficient range obtained in humid air, dry nitrogen and vacuum for the range of applied loads were respectively 0.22 to 0.27, 0.02 to 0.03, and 0.007 to 0.013. Coating lifetime was over 100 000 cycles for the entire load range tested in air and nitrogen, but was affected by the applied load as far as tests in vacuum are considered. The specific wear rate was lower than 1×10–5 mm3 N-1 m-1 under all test conditions, which was considered favourable.

Improved Wear Performance by the Incorporation of Solid Lubricants During Thermal Spraying

2000 ◽  
Author(s):  
B.R. Marple ◽  
J. Voyer
Keyword(s):  
Sliding Wear ◽  
Solid Lubricant ◽  
Thermal Spraying ◽  
Solid Lubricants ◽  
Degradation Process ◽  
Tribological Performance ◽  
Optimum Level ◽  
Wear Performance ◽  
Wear Tests ◽  
Minimum Wear

Abstract For components that are required to function in sliding or rubbing contact with other parts, degradation often occurs through wear due to friction between the two contacting surfaces. Depending on the nature of the materials being used, the addition of water as a lubricant may introduce corrosion and accelerate the degradation process. To improve the performance and increase the life of these components, coatings may be applied to the regions subject to the greatest wear. These coatings may be engineered to provide internal pockets of solid lubricant in order to improve the tribological performance. In the present study, coatings containing a solid lubricant were produced by thermal spraying feedstock powders consisting of a blend of tungsten carbide-metal and a fluorinated ethylene-propylene copolymer-based material. The volume content of this Teflon-based material in the feedstock ranged from 3.5 to 36%. These feedstocks were deposited using a high velocity oxy-fuel system to produce coatings having a level of porosity below 2%. Sliding wear tests in which coated rotors were tested in contact with stationary carbon-graphite disks identified an optimum level of Teflon-based material in the feedstock formulation required to produce coatings exhibiting minimum wear. This optimum level was in the range of 7-17% by volume and depended on the composition of the cermet constituent. Reductions in mass loss for the couples on the order of 50% (an improvement in performance by a factor of approximately two) were obtained for the best-performing compositions, as compared to couples m which the coating contained no solid lubricant.

Thermoelastic instability during sliding of inhomogeneous materials with different thermophysical properties

2021 ◽  
pp. 61-65
Author(s):  
I.Yu. Tsukanov
Keyword(s):  
Steady State ◽  
Wear Rate ◽  
Periodic Structure ◽  
Linear Dependence ◽  
Thermophysical Properties ◽  
Frictional Heating ◽  
Applied Pressure ◽  
Inhomogeneous Material ◽  
Inhomogeneous Materials ◽  
Thermoelastic Instability

The conditions for the appearance of thermoelastic instability are determined by modeling of the frictional heating during sliding of the surface of an inhomogeneous material having a periodic structure, consisting of elements with different thermophysical properties. Cases of the absence of wear and steady-state wear conditions with a linear dependence of the wear rate on the applied pressure and sliding speed are considered. Keywords: inhomogeneous material, matrix, fiber, thermoelastic instability, wear, periodic structure. [email protected]

scholarly journals Extruded and Injection Moulded Virgin PA 6/6 as Abrasion Resistant Material

2017 ◽  
Vol 2017 ◽  
pp. 1-9
Author(s):  
J. Sukumaran ◽  
R. Keresztes ◽  
G. Kalácska ◽  
H. Almaliki ◽  
P. D. Neis ◽  
...  
Keyword(s):  
Wear Rate ◽  
Extrusion Process ◽  
Wear Behaviour ◽  
Protective Agent ◽  
Tribological Behaviour ◽  
Wear Performance ◽  
Wear Response ◽  
Wear Tests ◽  
Proper Balance ◽  
Increasing Load

Polyamide (PA6/6) is often used as a tribological pair in abrasion prevalent applications such as hinges and sliders. PA6/6 is frequently processed by injection moulding and extrusion process. It is known that these processes influence the polymers mechanical behaviour, but their influence on the polymers wear response has not been studied. Hence the present research attempts to study the influence of different manufacturing processes on tribological behaviour for PA6/6. Wear tests were performed on a pin abrading tester (DIN 50322). Abrasion resistance of both extruded and injection moulded PA6/6 were tested at different loads (20 and 35 N). Single-pass (nonoverlapping mode) and multipass testing (overlapping mode) were used to understand the influence of clogging of wear debris. It is evidenced that with increasing load the specific wear rate decreases; moreover, fine abrasives tend to reduce the wear rate. In multipass testing a transfer layer clogged on the counterface that acted as a protective agent and lowers wear rate. Poor mechanical strength of injection moulded polymers is apparently compensated by microstructural response for having a similar wear behaviour between extruded and injection moulded PA 6/6. Hence a proper balance between microstructural and mechanical characteristics is an absolute must in PA 6/6 for better wear performance.

scholarly journals Sliding Wear of Conventional and Suspension Sprayed Nanocomposite WC-Co Coatings: An Invited Review

2021 ◽  
Author(s):  
R. Ahmed ◽  
O. Ali ◽  
C. C. Berndt ◽  
A. Fardan
Keyword(s):  
Wear Rate ◽  
Thermal Spray ◽  
Sliding Wear ◽  
Failure Modes ◽  
Thermal Spray Coatings ◽  
Annual Growth Rate ◽  
Total Energy Consumption ◽  
Wear Performance ◽  
Wear Rates ◽  
Spray Coatings

AbstractThe global thermal spray coatings market was valued at USD 10.1 billion in 2019 and is expected to grow at a compound annual growth rate of 3.9% from 2020 to 2027. Carbide coatings form an essential segment of this market and provide cost-effective and environmental friendly tribological solutions for applications in aerospace, industrial gas turbine, automotive, printing, oil and gas, steel, and pulp and paper industries. Almost 23% of the world’s total energy consumption originates from tribological contacts. Thermal spray WC-Co coatings provide excellent wear resistance for industrial applications in sliding and rolling contacts. Some of these applications in abrasive, sliding and erosive conditions include sink rolls in zinc pots, conveyor screws, pump housings, impeller shafts, aircraft flap tracks, cam followers and expansion joints. These coatings are considered as a replacement of the hazardous chrome plating for tribological applications. The microstructure of thermal spray coatings is however complex, and the wear mechanisms and wear rates vary significantly when compared to cemented WC-Co carbides or vapour deposition WC coatings. This paper provides an expert review of the tribological considerations that dictate the sliding wear performance of thermal spray WC-Co coatings. Structure–property relationships and failure modes are discussed to grasp the design aspects of WC-Co coatings for tribological applications. Recent developments of suspension sprayed nanocomposite coatings are compared with conventional coatings in terms of performance and failure mechanisms. The dependency of coating microstructure, binder material, carbide size, fracture toughness, post-treatment and hardness on sliding wear performance and test methodology is discussed. Semiempirical mathematical models of wear rate related to the influence of tribological test conditions and coating characteristics are analysed for sliding contacts. Finally, advances for numerical modelling of sliding wear rate are discussed.

Abrasive wear response of Al-Si–SiCp composite: Effect of friction heat and friction coefficient

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Raj Kumar Singh ◽  
Amit Telang ◽  
Satyabrata Das
Keyword(s):  
Heat Treatment ◽  
Friction Coefficient ◽  
Abrasive Wear ◽  
Applied Load ◽  
Frictional Heating ◽  
Matrix Alloy ◽  
Composite Effect ◽  
Friction Heat ◽  
Wear Response ◽  
Abrasive Size

Abstract The effects of friction heat and friction coefficient on the abrasive wear response of Al-7.5Si–SiCp composite against low-cost hypereutectic (Al-17.5Si) alloy were investigated as functions of the abrasive size and applied load in both as-cast and after heat-treatment conditions. Experiments were performed on pin-on-disc apparatus at 38 –80 μm abrasive size, 5 – 20 N applied load, 100 –400 m abrading (sliding) distances and 1 m s–1 constant sliding speed. The frictional heating of as-cast and heat-treated composite was superior compared to the matrix alloy and hypereutectic alloy, whereas the trend reversed for the friction coefficient. The frictional heating and friction coefficient of the materials increased with the abrasive size and applied load in both as-cast and after heat-treatment. The worn surface and wear debris particles were examined by using field emission scanning electron microscopy to understand the wear mechanism.

scholarly journals Influence of Test Conditions on Sliding Wear Performance of High Velocity Air Fuel-Sprayed WC–CoCr Coatings

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3074
Author(s):  
Kaveh Torkashvand ◽  
Vinod Krishna Selpol ◽  
Mohit Gupta ◽  
Shrikant Joshi
Keyword(s):  
Wear Rate ◽  
Test Performance ◽  
Sliding Wear ◽  
Normal Load ◽  
Specific Wear Rate ◽  
Wear Behaviour ◽  
Wear Performance ◽  
Test Conditions ◽  
Test Parameters ◽  
Sliding Distance

Sliding wear performance of thermal spray WC-based coatings has been widely studied. However, there is no systematic investigation on the influence of test conditions on wear behaviour of these coatings. In order to have a good understanding of the effect of test parameters on sliding wear test performance of HVAF-sprayed WC–CoCr coatings, ball-on-disc tests were conducted under varying test conditions, including different angular velocities, loads and sliding distances. Under normal load of 20 N and sliding distance of 5 km (used as ‘reference’ conditions), it was shown that, despite changes in angular velocity (from 1333 rpm up to 2400 rpm), specific wear rate values experienced no major variation. No major change was observed in specific wear rate values even upon increasing the load from 20 N to 40 N and sliding distance from 5 km to 10 km, and no significant change was noted in the prevailing wear mechanism, either. Results suggest that no dramatic changes in applicable wear regime occur over the window of test parameters investigated. Consequently, the findings of this study inspire confidence in utilizing test conditions within the above range to rank different WC-based coatings.

Sign in / Sign up

Export Citation Format

Share Document