Thermal Nanofluid Property Model With Application to Nanofluid Flow in a Parallel Disk System—Part II: Nanofluid Flow Between Parallel Disks

2012 ◽  
Vol 134 (5) ◽  
Author(s):  
Yu Feng ◽  
Clement Kleinstreuer
Keyword(s):  
Heat Transfer ◽  
Entropy Generation ◽  
Cooling System ◽  
Pure Water ◽  
Jet Impingement ◽  
Velocity Profiles ◽  
Entropy Generation Rate ◽  
Nanofluid Flow ◽  
Parallel Disks ◽  
Simulation Results

This is the second part of a two-part paper which proposes a new theory explaining the experimentally observed enhancement of the thermal conductivity, knf, of nanofluids (Part I) and discusses simulation results of nanofluid flow in an axisymmetric jet-impingement cooling system using different knf-models (Part II). Specifically, Part II provides numerical simulations of convective nanofluid heat transfer in terms of velocity profiles, friction factor, temperature distributions, and Nusselt numbers, employing the new knf-model. Flow structures and the effects of nanoparticle addition on heat transfer and entropy generation are discussed as well. Analytical expressions for velocity profiles and friction factors, assuming quasi-fully-developed flow between parallel disks, have been derived and validated for nanofluids as well. Based on the numerical simulation results for both alumina-water nanofluids and pure water, it can be concluded that nanofluids show better heat transfer performance than convectional coolants with no great penalty in pumping power. Furthermore, the system’s entropy generation rate is lower for nanofluids than for pure water.

Modeling heat transfer of nanofluid flow in microchannels with electrokinetic and slippery effects using Buongiorno’s model

2019 ◽  
Vol 29 (8) ◽  
pp. 2566-2587 ◽  
Author(s):  
Hang Xu ◽  
Huang Huang ◽  
Xiao-Hang Xu ◽  
Qiang Sun
Keyword(s):  
Heat Transfer ◽  
Entropy Generation ◽  
Slip Length ◽  
Generation Rate ◽  
Entropy Generation Rate ◽  
Lower Wall ◽  
Volumetric Concentration ◽  
Nanofluid Flow ◽  
Cross Sectional ◽  
Content Type

PurposeThis paper aims to study the heat transfer of nanofluid flow driven by the move of channel walls in a microchannel under the effects of the electrical double layer and slippery properties of channel walls. The distributions of velocity, temperature and nanoparticle volumetric concentration are analyzed under different slip-length. Also, the variation rates of flow velocity, temperature, concentration of nanoparticle, the pressure constant, the local volumetric entropy generation rate and the total cross-sectional entropy generation are analyzed.Design/methodology/approachA recently developed model is chosen which is robust and reasonable from the point of view of physics, as it does not impose nonphysical boundary conditions, for instance, the zero electrical potential in the middle plane of the channel or the artificial pressure constant. The governing equations of flow motion, energy, electrical double layer and stream potential are derived with slip boundary condition presented. The model is non-dimensionalized and solved by using the homotopy analysis method.FindingsSlip-length has significant influences on the velocity, temperature and nanoparticle volumetric concentration of the nanofluid. It also has strong effects on the pressure constant. With the increase of the slip-length, the pressure constant of the nanofluid in the horizontal microchannel decreases. Both the local volumetric entropy generation rate and total cross-sectional entropy generation rate are significantly affected by both the slip-length of the lower wall and the thermal diffusion. The local volumetric entropy generation rate at the upper wall is always higher than that around the lower wall. Also, the larger the slip-length is, the lower the total cross-sectional entropy generation rate is when the thermal diffusion is moderate.Originality/valueThe findings in this work on the heat transfer and flow phenomena of the nanofluid in microchannel are expected to make a contribution to guide the design of micro-electro-mechanical systems.

Lattice Boltzmann simulation of free convection’s hydrothermal aspects in a finned/multi-pipe cavity filled with CuO-water nanofluid

2019 ◽  
Vol 29 (3) ◽  
pp. 1058-1078 ◽  
Author(s):  
Alireza Rahimi ◽  
Pouria Azarikhah ◽  
Abbas Kasaeipoor ◽  
Emad Hasani Malekshah ◽  
Lioua Kolsi
Keyword(s):  
Heat Transfer ◽  
Rayleigh Number ◽  
Heat Transfer Rate ◽  
Entropy Generation ◽  
Lattice Boltzmann ◽  
Transfer Rate ◽  
Pure Water ◽  
Nanofluid Flow ◽  
Content Type ◽  
Flow And Heat Transfer

Purpose This paper aims to investigate the natural convection fluid flow and heat transfer in a finned/multi-pipe cavity. Design/methodology/approach The cavity is filled with the CuO-water nanofluid. The Koo–Kleinstreuer–Li model is used to estimate the dynamic viscosity and consider Brownian motion. On the other hand, the effect of the shapes of nanoparticles on the thermal conductivity and related heat transfer rate is presented. Findings In the present investigation, the governing parameters are Rayleigh number, CuO nanoparticle concentration in pure water and the thermal arrangements of internal active fins and solid bodies. Impacts of these parameters on the nanofluid flow, heat transfer rate, total/local entropy generation and heatlines are presented. It is concluded that adding nanoparticles to the pure fluid has a significant positive influence on the heat transfer performance. In addition, the average Nusselt number and total entropy generation have direct a relationship with the Rayleigh number. The thermal arrangement of the internal bodies and fins is a good controlling tool to determine the desired magnitude of heat transfer rate. Originality/value The originality of this paper is to use the lattice Boltzmann method in simulating the nanofluid flow and heat transfer within a cavity included with internal active bodies and fins.

Heat Transfer Characteristics of Downward Facing Hot Horizontal Surfaces Using Mist Jet Impingement

2017 ◽  
Author(s):  
Ashutosh Kumar Yadav ◽  
Parantak Sharma ◽  
Avadhesh Kumar Sharma ◽  
Mayank Modak ◽  
Vishal Nirgude ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Surface Heat Flux ◽  
Cooling System ◽  
Water Pressure ◽  
Jet Impingement ◽  
Surface Heat ◽  
Heat Transfer Characteristics ◽  
Impingement Cooling ◽  
Transfer Characteristics

Impinging jet cooling technique has been widely used extensively in various industrial processes, namely, cooling and drying of films and papers, processing of metals and glasses, cooling of gas turbine blades and most recently cooling of various components of electronic devices. Due to high heat removal rate the jet impingement cooling of the hot surfaces is being used in nuclear industries. During the loss of coolant accidents (LOCA) in nuclear power plant, an emergency core cooling system (ECCS) cool the cluster of clad tubes using consisting of fuel rods. Controlled cooling, as an important procedure of thermal-mechanical control processing technology, is helpful to improve the microstructure and mechanical properties of steel. In industries for heat transfer efficiency and homogeneous cooling performance which usually requires a jet impingement with improved heat transfer capacity and controllability. It provides better cooling in comparison to air. Rapid quenching by water jet, sometimes, may lead to formation of cracks and poor ductility to the quenched surface. Spray and mist jet impingement offers an alternative method to uncontrolled rapid cooling, particularly in steel and electronics industries. Mist jet impingement cooling of downward facing hot surface has not been extensively studied in the literature. The present experimental study analyzes the heat transfer characteristics a 0.15mm thick hot horizontal stainless steel (SS-304) foil using Internal mixing full cone (spray angle 20 deg) mist nozzle from the bottom side. Experiments have been performed for the varied range of water pressure (0.7–4.0 bar) and air pressure (0.4–5.8 bar). The effect of water and air inlet pressures, on the surface heat flux has been examined in this study. The maximum surface heat flux is achieved at stagnation point and is not affected by the change in nozzle to plate distance, Air and Water flow rates.

Entropy generation and heat transfer analysis for ferrofluid flow between two rotating disks with variable conductivity

2021 ◽  
pp. 095440622199118
Author(s):  
Anupam Bhandari
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Differential Equations ◽  
Entropy Generation ◽  
Heat Transfer Analysis ◽  
Entropy Generation Rate ◽  
Geometrical Parameters ◽  
Rotating Disks ◽  
Coupled Differential Equations ◽  
Lower Disk

Present model analyze the flow and heat transfer of water-based carbon nanotubes (CNTs) [Formula: see text] ferrofluid flow between two radially stretchable rotating disks in the presence of a uniform magnetic field. A study for entropy generation analysis is carried out to measure the irreversibility of the system. Using similarity transformation, the governing equations in the model are transformed into a set of nonlinear coupled differential equations in non-dimensional form. The nonlinear coupled differential equations are solved numerically through the finite element method. Variable viscosity, variable thermal conductivity, thermal radiation, and volume concentration have a crucial role in heat transfer enhancement. The results for the entropy generation rate, velocity distributions, and temperature distribution are graphically presented in the presence of physical and geometrical parameters of the flow. Increasing the values of ferromagnetic interaction number, Reynolds number, and temperature-dependent viscosity enhances the skin friction coefficients on the surface and wall of the lower disk. The local heat transfer rate near the lower disk is reduced in the presence of Harman number, Reynolds number, and Prandtl number. The ferrohydrodynamic flow between two rotating disks might be useful to optimize the use of hybrid nanofluid for liquid seals in rotating machinery.

scholarly journals Non-Newtonian effect on heat transfer and entropy generation of natural convection nanofluid flow inside a vertical wavy porous cavity

2021 ◽  
Vol 3 (3) ◽  
Author(s):  
Mahbuba Tasmin ◽  
Preetom Nag ◽  
Zarin T. Hoque ◽  
Md. Mamun Molla
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Entropy Generation ◽  
Power Law ◽  
Volume Fraction ◽  
Local Entropy ◽  
Nanofluid Flow ◽  
Porosity Level ◽  
Power Law Index ◽  
Local Entropy Generation

AbstractA numerical study on heat transfer and entropy generation in natural convection of non-Newtonian nanofluid flow has been explored within a differentially heated two-dimensional wavy porous cavity. In the present study, copper (Cu)–water nanofluid is considered for the investigation where the specific behavior of Cu nanoparticles in water is considered to behave as non-Newtonian based on previously established experimental results. The power-law model and the Brinkman-extended Darcy model has been used to characterize the non-Newtonian porous medium. The governing equations of the flow are solved using the finite volume method with the collocated grid arrangement. Numerical results are presented through streamlines, isotherms, local Nusselt number and entropy generation rate to study the effects of a range of Darcy number (Da), volume fractions (ϕ) of nanofluids, Rayleigh numbers (Ra), and the power-law index (n). Results show that the rate of heat transfer from the wavy wall to the medium becomes enhanced by decreasing the power-law index but increasing the volume fraction of nanoparticles. Increase of porosity level and buoyancy forces of the medium augments flow strength and results in a thinner boundary layer within the cavity. At negligible porosity level of the enclosure, effect of volume fraction of nanoparticles over thermal conductivity of the nanofluids is imperceptible. Interestingly, when the Darcy–Rayleigh number $$Ra^*\gg 10$$ R a ∗ ≫ 10 , the power-law effect becomes more significant than the volume fraction effect in the augmentation of the convective heat transfer process. The local entropy generation is highly dominated by heat transfer irreversibility within the porous enclosure for all conditions of the flow medium. The particular wavy shape of the cavity strongly influences the heat transfer flow pattern and local entropy generation. Interestingly, contour graphs of local entropy generation and local Bejan number show a rotationally symmetric pattern of order two about the center of the wavy cavity.

MHD and nonlinear thermal radiation effects on hybrid nanofluid past a wedge with heat source and entropy generation

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Fazle Mabood ◽  
Anum Shafiq ◽  
Waqar Ahmed Khan ◽  
Irfan Anjum Badruddin
Keyword(s):  
Heat Transfer ◽  
Differential Equations ◽  
Heat Source ◽  
Thermal Radiation ◽  
Entropy Generation ◽  
Entropy Generation Rate ◽  
Design Parameters ◽  
Hybrid Nanofluid ◽  
Nonlinear Thermal Radiation ◽  
Content Type

Purpose This study aims to investigate the irreversibility associated with the Fe3O4–Co/kerosene hybrid-nanofluid past a wedge with nonlinear radiation and heat source. Design/methodology/approach This study reports the numerical analysis of the hybrid nanofluid model under the implications of the heat source and magnetic field over a static and moving wedge with slips. The second law of thermodynamics is applied with nonlinear thermal radiation. The system that comprises differential equations of partial derivatives is remodeled into the system of differential equations via similarity transformations and then solved through the Runge–Kutta–Fehlberg with shooting technique. The physical parameters, which emerges from the derived system, are discussed in graphical formats. Excellent proficiency in the numerical process is analyzed by comparing the results with available literature in limiting scenarios. Findings The significant outcomes of the current investigation are that the velocity field uplifts for higher velocity slip and magnetic strength. Further, the heat transfer rate is reduced with the incremental values of the Eckert number, while it uplifts with thermal slip and radiation parameters. An increase in Brinkmann’s number uplifts the entropy generation rate, while that peters out the Bejan number. The results of this study are of importance involving in the assessment of the effect of some important design parameters on heat transfer and, consequently, on the optimization of industrial processes. Originality/value This study is original work that reports the hybrid nanofluid model of Fe3O4–Co/kerosene.

Entropy generation of nanofluid flow and heat transfer driven through a paralleled microchannel

2019 ◽  
Vol 97 (6) ◽  
pp. 678-691 ◽  
Author(s):  
Hang Xu ◽  
Ammarah Raees ◽  
Xiao-Hang Xu
Keyword(s):  
Magnetic Field ◽  
Brownian Motion ◽  
Entropy Generation ◽  
Current Model ◽  
Entropy Generation Rate ◽  
Physical Parameters ◽  
Nanofluid Flow ◽  
Buongiorno’S Model ◽  
Flow Models ◽  
Flow And Heat Transfer

In this paper, a fully-developed, immiscible nanofluid flow in a paralleled microchannel in the presence of a magnetic field is investigated. Buongiorno’s model is applied to describe the behaviors of the nanofluid flow. Different from most previous studies on microchannel flow, here the pressure term is considered as unknown, which makes the current model compatible with the commonly accepted channel flow models. The influences of various physical parameters on important physical quantities are given. The entropy generation analysis is performed. Variations of local and global entropy generations with the magnetic field parameter, the electric field, and the viscous dissipation parameter under various ratios of the thermophoresis parameter to the Brownian motion parameter are illustrated. The results indicate that the entropy generation rate strongly depends on the thermophoresis and the Brownian motion parameters. Their increase enhances the total irreversibility of entropy generation.

scholarly journals Effect of corrugated minichannel variable width on entropy generation for convective heat transfer of alpha-Alumina-water nanofluid

2021 ◽  
Vol 2053 (1) ◽  
pp. 012016
Author(s):  
N M Muhammad ◽  
N A C Sidik ◽  
A Saat ◽  
Y Asako ◽  
W M A A Japar ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Convective Heat Transfer ◽  
Entropy Production ◽  
Convective Heat ◽  
Entropy Generation ◽  
Entropy Generation Rate ◽  
Thermal Systems ◽  
Volume Fractions ◽  
Thermal Entropy ◽  
Alpha Alumina

Abstract Energy management and sustainability in thermal systems require maximum utilization of resources with minimal losses. However, it is rarely unattainable due to the ever-increasing need for a high-performance system combined with device size reduction. The numerical study examined convective heat transfer of an alpha-Alumina-water nanofluid in variable-width corrugated minichannel heat sinks. The objective is to study the impact of nanoparticle volume fractions and flow area variation on the entropy generation rate. The determining variables are 0.005 – 0.02 volume fractions, the fluid velocity 3 – 5.5 m/s and heat flux of 85 W/cm2. The numerical results show an acceptable correlation with the experiment results. The results indicate the thermal entropy production drop with an increase in nanoparticles volume fraction. Contrastingly, the frictional resistance entropy suggests the opposite trend due to the turbulence effect on the fluid viscosity. The induction of Alumina-Water nanofluid with enhanced thermal conductivity declined the entropy generation rate compared to water alone. The increase in width ratio by 16% between the cases translates to at least a 9% increase in thermal entropy production. The outcome of this study can provide designers and operators of thermal systems more insight into entropy management in corrugated heatsinks.

scholarly journals Enhanced heat transfer characteristics of conjugated air jet impingement on a finned heat sink

2017 ◽  
Vol 21 (1 Part A) ◽  
pp. 279-288 ◽  
Author(s):  
Shuxia Qiu ◽  
Peng Xu ◽  
Liping Geng ◽  
Arun Mujumdar ◽  
Zhouting Jiang ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Heat Sink ◽  
Heat Transfer Performance ◽  
Cooling System ◽  
Flow Characteristics ◽  
Jet Impingement ◽  
Transfer Performance ◽  
Transfer Enhancement ◽  
Air Jet

Air jet impingement is one of the effective cooling techniques employed in micro-electronic industry. To enhance the heat transfer performance, a cooling system with air jet impingement on a finned heat sink is evaluated via the computational fluid dynamics method. A two-dimensional confined slot air impinging on a finned flat plate is modeled. The numerical model is validated by comparison of the computed Nusselt number distribution on the impingement target with published experimental results. The flow characteristics and heat transfer performance of jet impingement on both of smooth and finned heat sinks are compared. It is observed that jet impingement over finned target plate improves the cooling performance significantly. A dimensionless heat transfer enhancement factor is introduced to quantify the effect of jet flow Reynolds number on the finned surface. The effect of rectangular fin dimensions on impingement heat transfer rate is discussed in order to optimize the cooling system. Also, the computed flow and thermal fields of the air impingement system are examined to explore the physical mechanisms for heat transfer enhancement.

scholarly journals Heat transfer and entropy generation in a microchannel with longitudinal vortex generators using Nanofluids

2020 ◽  
Author(s):  
Amin Ebrahimi ◽  
Farhad Rikhtegar Nezami ◽  
Amin Sabaghan ◽  
Ehsan Roohi
Keyword(s):  
Heat Transfer ◽  
Entropy Generation ◽  
Single Phase ◽  
Pure Water ◽  
Vortex Generators ◽  
Longitudinal Vortex ◽  
Working Fluid ◽  
Two Phase ◽  
Rectangular Microchannel ◽  
Important Conclusion

Conjugated heat transfer and hydraulic performance for nanofluid flow in a rectangular microchannel heat sink with LVGs (longitudinal vortex generators) are numerically investigated using at different ranges of Reynolds numbers. Three-dimensional simulations are performed on a microchannel heated by a constant heat flux with a hydraulic diameter of 160 μm and six pairs of LVGs using a single-phase model. Coolants are selected to be nanofluids containing low volume-fractions (0.5%–3.0%) of Al2O3 or CuO nanoparticles with different particle sizes dispersed in pure water. The employed model is validated and compared by published experimental, and single-phase and two-phase numerical data for various geometries and nanoparticle sizes. The results demonstrate that heat transfer is enhanced by 2.29–30.63% and 9.44%–53.06% for water-Al2O3 and water-CuO nanofluids, respectively, in expense of increasing the pressure drop with respect to pure-water by 3.49%–16.85% and 6.5%–17.70%, respectively. We have also observed that the overall efficiency is improved by 2.55%–29.05% and 9.78%–50.64% for water-Al2O3 and water-CuO nanofluids, respectively. The results are also analyzed in terms of entropy generation, leading to the important conclusion that using nanofluids as the working fluid could reduce the irreversibility level in the rectangular microchannel heat sinks with LVGs. No exterma (minimums) is found for total entropy generation for the ranges of parameters studied.

Sign in / Sign up

Export Citation Format

Share Document