The Effect of Intake Valve Deactivation on Lean Stratified Charge Combustion at an Idling Condition of a Spark Ignition Direct Injection Engine

2012 ◽  
Vol 134 (9) ◽  
Author(s):  
Ronald O. Grover ◽  
Junseok Chang ◽  
Edward R. Masters ◽  
Paul M. Najt ◽  
Aditya Singh
Keyword(s):  
Laminar Flame ◽  
Direct Injection ◽  
Combustion Process ◽  
Spark Ignition ◽  
Combustion Efficiency ◽  
Combustion Stability ◽  
Charge Motion ◽  
Piston Bowl ◽  
Light Load ◽  
Spark Plug

A combined experimental and analytical study was carried out to understand the improvement in combustion performance of a four-valve spark ignition direct injection (SIDI) wall-guided engine operating at lean, stratified idle with enhanced in-cylinder charge motion by deactivating one of the two intake valves. A fully warmed-up engine was operated at low speed, light load by injecting the fuel from a pressure-swirl injector during the compression stroke to produce a stratified fuel cloud surrounding the spark plug at the time of ignition. Steady state flow-bench measurements and computational fluid dynamics (CFD) calculations showed that valve deactivation primarily increased the in-cylinder swirl intensity as compared with opening both intake valves. Engine dynamometer measurements showed an increase in charge motion led to improved combustion stability, increased combustion efficiency, lower fuel consumption, and higher dilution tolerance. A CFD study was conducted using in-house models of spray and combustion to simulate the engine operating with and without valve deactivation. The computations demonstrated that the improved combustion was primarily driven by higher laminar flame speeds through enhanced mixing of internal residual gases, better containment of the fuel cloud within the piston bowl, and higher postflame diffusion burn rates during the initial, main, and late stages of the combustion process, respectively.

The Effect of Intake Valve Deactivation on Lean Stratified Charge Combustion at an Idling Condition of a Spark-Ignition Direct-Injection (SIDI) Engine

2011 ◽  
Author(s):  
Ronald O. Grover ◽  
Junseok Chang ◽  
Edward R. Masters ◽  
Paul Najt ◽  
Aditya Singh
Keyword(s):  
Laminar Flame ◽  
Direct Injection ◽  
Combustion Process ◽  
Combustion Efficiency ◽  
Combustion Stability ◽  
Charge Motion ◽  
Piston Bowl ◽  
Light Load ◽  
Spark Plug ◽  
Swirl Injector

A combined experimental and analytical study was carried out to understand the improvement in combustion performance of a 4-valve SIDI wall-guided engine operating at lean, stratified idle with enhanced in-cylinder charge motion by deactivating one of the two intake valves. A fully warmed-up engine was operated at low speed, light load by injecting the fuel from a pressure-swirl injector during the compression stroke to produce a stratified fuel cloud surrounding the spark plug at the time of ignition. Steady state flow-bench measurements and CFD calculations showed that valve deactivation primarily increased the in-cylinder swirl intensity as compared with opening both intake valves. Engine dynamometer measurements showed an increase in charge motion led to improved combustion stability, increased combustion efficiency, lower fuel consumption, and higher dilution tolerance. A CFD study was conducted using in-house models of spray and combustion to simulate the engine operating with and without valve deactivation. The computations demonstrated that the improved combustion was primarily driven by higher laminar flame speeds through enhanced mixing of internal residual gases, better containment of the fuel cloud within the piston bowl, and higher post-flame diffusion burn rates during the initial, main, and late stages of the combustion process, respectively.

Combustion Characteristics of Stratified Mixture in Lean-Burn LPG Direct-Injection Engine With Spray-Guided Combustion System

2014 ◽  
Author(s):  
Cheolwoong Park ◽  
Seungmook Oh ◽  
Taeyoung Kim ◽  
Heechang Oh ◽  
Choongsik Bae
Keyword(s):  
Fuel Consumption ◽  
Compression Ratio ◽  
Fuel Economy ◽  
Direct Injection ◽  
Combustion Process ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Combustion Stability ◽  
Direct Injection Engine ◽  
Brake Mean Effective Pressure

Today, we are faced with the problems of global warming and fossil fuel depletion, and they have led to the enforcement of new emissions regulations. Direct-injection spark-ignition engines are a very promising technology that can comply with the new regulations. These engines offer the advantages of better fuel economy and lower emissions than conventional port-injection engines. The use of LPG as the fuel reduces carbon emissions because of its vaporization characteristics and the fact that it has lower carbon content than gasoline. An experimental study was carried out to investigate the combustion process and emission characteristics of a 2-liter spray-guided LPG direct-injection engine under lean operating conditions. The engine was operated at a constant speed of 2000 rpm under 0.2-MPa brake mean effective pressure, which corresponds to a common operation point of a passenger vehicle. Combustion stability, which is the most important component of engine performance, is closely related to the operation strategy and it significantly influences the degree of fuel consumption reduction. In order to achieve stable combustion with a stratified LPG mixture, an inter-injection spark ignition (ISI) strategy, which is an alternative control strategy to two-stage injection, was employed. The effects of the compression ratio on fuel economy were also assessed; due to the characteristics of the stratified LPG mixture, the fuel consumption did not reduce when the compression ratio was increased.

A Numerical Investigation of Combustion and Mixture Formation in a Compressed Natural Gas DISI Engine With Centrally Mounted Single-Hole Injector

2013 ◽  
Vol 135 (9) ◽  
Author(s):  
B. Yadollahi ◽  
M. Boroomand
Keyword(s):  
Natural Gas ◽  
Internal Combustion Engines ◽  
Gasoline Engine ◽  
Direct Injection ◽  
Combustion Process ◽  
Spark Ignition ◽  
Computational Effort ◽  
Single Hole ◽  
Piston Head ◽  
Spark Plug

Direct injection of natural gas into the cylinder of spark ignition (SI) engines has shown a great potential to achieve the best fuel economy and reduced emission levels. Since the technology is rather new, in-cylinder flow phenomena have not been completely investigated. In this study, a numerical model has been developed in AVL FIRE software to perform an investigation of natural gas direct injection into the cylinder of spark ignition internal combustion engines. In this regard, two main parts have been taken into consideration aiming to convert a multipoint port fuel injection (MPFI) gasoline engine to a direct injection natural gas (NG) engine. In the first part of the study, multidimensional simulations of transient injection process, mixing, and flow field have been performed. Using the moving mesh capability, the validated model has been applied to methane injection into the cylinder of a direct injection engine. Five different piston head shapes have been taken into consideration in the investigations. An inwardly opening single-hole injector has been adapted to all cases. The injector location has been set to be centrally mounted. The effects of combustion chamber geometry have been studied on the mixing of air-fuel inside the cylinder via the quantitative and qualitative representation of results. In the second part, an investigation of the combustion process has been performed on the selected geometry. The spark plug location and ignition timing have been studied as two of the most important variables. Simulation of transient injection was found to be a challenging task because of required computational effort and numerical instabilities. Injection results showed that the narrow bowl piston head geometry is the most suited geometry for NG direct injection (DI) application. A near center position has been shown to be the best spark plug location based on the combustion studies. It has been shown that advanced ignitions timings of up to 50 degrees crank angle ( °CA) should be used in order to obtain better combustion performance.

Combustion Characteristics of Stratified Mixture in Lean-Burn Liquefied Petroleum Gas Direct-Injection Engine With Spray-Guided Combustion System

2015 ◽  
Vol 138 (7) ◽  
Author(s):  
Cheolwoong Park ◽  
Seungmook Oh ◽  
Taeyoung Kim ◽  
Heechang Oh ◽  
Choongsik Bae
Keyword(s):  
Fuel Consumption ◽  
Compression Ratio ◽  
Fuel Economy ◽  
Direct Injection ◽  
Combustion Process ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Combustion Stability ◽  
Liquefied Petroleum Gas ◽  
Direct Injection Engine

Today, we are faced with the problems of global warming and fossil fuel depletion, and they have led to the enforcement of new emissions regulations. Direct-injection spark-ignition engines are a very promising technology that can comply with the new regulations. These engines offer the advantages of better fuel economy and lower emissions than conventional port-injection engines. The use of liquefied petroleum gas (LPG) as the fuel reduces carbon emissions because of its vaporization characteristics and the fact that it has lower carbon content than gasoline. An experimental study was carried out to investigate the combustion process and emission characteristics of a 2 l spray-guided LPG direct-injection engine under lean operating conditions. The engine was operated at a constant speed of 2000 rpm under 0.2 MPa brake mean effective pressure (BMEP), which corresponds to a common operation point of a passenger vehicle. Combustion stability, which is the most important component of engine performance, is closely related to the operation strategy and it significantly influences the degree of fuel consumption reduction. In order to achieve stable combustion with a stratified LPG mixture, an interinjection spark ignition (ISI) strategy, which is an alternative control strategy to two-stage injection, was employed. The effects of the compression ratio on fuel economy were also assessed; due to the characteristics of the stratified LPG mixture, the fuel consumption did not reduce when the compression ratio was increased.

scholarly journals Effects of mixture formation strategies on combustion in dual-fuel engines – a review

2021 ◽  
Vol 184 (1) ◽  
pp. 30-40
Author(s):  
Ireneusz Pielecha ◽  
Maciej Sidorowicz
Keyword(s):  
Internal Combustion Engines ◽  
Direct Injection ◽  
Combustion Process ◽  
Critical Factor ◽  
Diesel Oil ◽  
Combustion Efficiency ◽  
Dual Fuel ◽  
Compression Ignition ◽  
Mixture Formation ◽  
Spark Plug

The article presents an overview of technical solutions for dual fuel systems used in internal combustion engines. It covers the historical and contemporary genesis of using two fuels simultaneously in the combustion process. The authors pay attention to the value of the excess air coefficient in the cylinder, as the ignitability of the fuel dose near the spark plug is a critical factor. The mixture formation of compression ignition based systems are also analyzed. The results of research on indirect and direct injection systems (and their combinations) have been presented. Research sections were separated based to the use of gasoline with other fuels or diesel oil with other fuels. It was found that the use of two fuels in different configurations of the fuel supply systems extends the conditions for the use of modern combustion systems (jet controlled compression ignition, reactivity controlled compression ignition, intelligent charge compression ignition, premixed charge compression ignition), which will enable further improvement of combustion efficiency.

scholarly journals Optical Investigation of a Partial Fuel Stratification Strategy to Stabilize Overall Lean Operation of a DISI Engine Fueled with Gasoline and E30

Energies ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 396
Author(s):  
Cinzia Tornatore ◽  
Magnus Sjöberg
Keyword(s):  
Volume Fraction ◽  
Direct Injection ◽  
Combustion Process ◽  
Pilot Injection ◽  
Optical Investigation ◽  
Flame Kernel ◽  
Lean Combustion ◽  
Fuel Stratification ◽  
Spark Plug ◽  
Initial Flame

This paper offers new insights into a partial fuel stratification (PFS) combustion strategy that has proven to be effective at stabilizing overall lean combustion in direct injection spark ignition engines. To this aim, high spatial and temporal resolution optical diagnostics were applied in an optically accessible engine working in PFS mode for two fuels and two different durations of pilot injection at the time of spark: 210 µs and 330 µs for E30 (gasoline blended with ethanol by 30% volume fraction) and gasoline, respectively. In both conditions, early injections during the intake stroke were used to generate a well-mixed lean background. The results were compared to rich, stoichiometric and lean well-mixed combustion with different spark timings. In the PFS combustion process, it was possible to detect a non-spherical and highly wrinkled blue flame, coupled with yellow diffusive flames due to the combustion of rich zones near the spark plug. The initial flame spread for both PFS cases was faster compared to any of the well-mixed cases (lean, stoichiometric and rich), suggesting that the flame propagation for PFS is enhanced by both enrichment and enhanced local turbulence caused by the pilot injection. Different spray evolutions for the two pilot injection durations were found to strongly influence the flame kernel inception and propagation. PFS with pilot durations of 210 µs and 330 µs showed some differences in terms of shapes of the flame front and in terms of extension of diffusive flames. Yet, both cases were highly repeatable.

scholarly journals The Effect of RME-1-Butanol Blends on Combustion, Performance and Emission of a Direct Injection Diesel Engine

Energies ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2941
Author(s):  
Wojciech Tutak ◽  
Arkadiusz Jamrozik ◽  
Karol Grab-Rogaliński
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Direct Injection ◽  
Specific Energy Consumption ◽  
Combustion Process ◽  
Constant Load ◽  
Combustion Stability ◽  
Performance And Emission ◽  
Energy Share ◽  
The Stability

The main objective of this study was assessment of the performance, emissions and combustion characteristics of a diesel engine using RME–1-butanol blends. In assessing the combustion process, great importance was placed on evaluating the stability of this process. Not only were the typical COVIMEP indicators assessed, but also the non-burnability of the characteristic combustion stages: ignition delay, time of 50% heat release and the end of combustion. The evaluation of the combustion process based on the analysis of heat release. The tests carried out on a 1-cylinder diesel engine operating at a constant load. Research and evaluation of the combustion process of a mixture of RME and 1-butanol carried out for the entire range of shares of both fuels up to 90% of 1-butanol energetic fraction. The participation of butanol in combustion process with RME increased the in-cylinder peak pressure and the heat release rate. With the increase in the share of butanol there was noted a decrease in specific energy consumption and an increase in engine efficiency. The share of butanol improved the combustion stability. There was also an increase in NOx emissions and decrease in CO and soot emissions. The engine can be power by blend up to 80% energy share of butanol.

scholarly journals Combustion Thermodynamics of Ethanol, n-Heptane, and n-Butanol in a Rapid Compression Machine with a Dual Direct Injection (DDI) Supply System

Energies ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2729
Author(s):  
Ireneusz Pielecha ◽  
Sławomir Wierzbicki ◽  
Maciej Sidorowicz ◽  
Dariusz Pietras
Keyword(s):  
Heat Release ◽  
Combustion Chamber ◽  
Internal Combustion Engines ◽  
Direct Injection ◽  
Combustion Process ◽  
Combustion Efficiency ◽  
Injection System ◽  
Rapid Compression Machine ◽  
Process Indicators ◽  
Rapid Compression

The development of internal combustion engines involves various new solutions, one of which is the use of dual-fuel systems. The diversity of technological solutions being developed determines the efficiency of such systems, as well as the possibility of reducing the emission of carbon dioxide and exhaust components into the atmosphere. An innovative double direct injection system was used as a method for forming a mixture in the combustion chamber. The tests were carried out with the use of gasoline, ethanol, n-heptane, and n-butanol during combustion in a model test engine—the rapid compression machine (RCM). The analyzed combustion process indicators included the cylinder pressure, pressure increase rate, heat release rate, and heat release value. Optical tests of the combustion process made it possible to analyze the flame development in the observed area of the combustion chamber. The conducted research and analyses resulted in the observation that it is possible to control the excess air ratio in the direct vicinity of the spark plug just before ignition. Such possibilities occur as a result of the properties of the injected fuels, which include different amounts of air required for their stoichiometric combustion. The studies of the combustion process have shown that the combustible mixtures consisting of gasoline with another fuel are characterized by greater combustion efficiency than the mixtures composed of only a single fuel type, and that the influence of the type of fuel used is significant for the combustion process and its indicator values.

A New Approach for Ignition Timing Correction in Spark Ignition Engines Based on Cylinder Tendency to Surface Ignition

2016 ◽  
Vol 819 ◽  
pp. 272-276 ◽  
Author(s):  
Ali Ghanaati ◽  
Mohd Farid Muhamad Said ◽  
Intan Zaurah Mat Darus ◽  
Amin Mahmoudzadeh Andwari
Keyword(s):  
Spark Ignition ◽  
Combustion Stability ◽  
Spark Ignition Engines ◽  
Gas Temperature ◽  
New Approach ◽  
Surface Ignition ◽  
Spark Plug ◽  
Engine Combustion ◽  
Si Engines ◽  
Exhaust Gas Temperature

The performance of Spark Ignition (SI) engines in terms of thermal efficiency can be restricted by knock. Although it is common for all SI engines to exhibit knock from compressed end-gas, knocks from surface ignition remains a more serious problem due to its effect on combustion stability and its obscurity to detect. This paper focuses on predicting the occurrence of knocks from surface ignition by monitoring exhaust gas temperature (EGT). EGT measured during an engine cycle without the spark plug firing. Therefore, EGT rises illustrated any combustion made by surface ignition. Modelling and simulation of a one-dimensional engine combustion done by using GT-Power. The new approach reduces the complexity as EGT monitoring does not require high computational demands, and the EGT signals are robust to noise. The method is validated against a variety of fuel properties and across engine conditions. A new approach is proposed as a measure to predict and detect the knock events.

Sign in / Sign up

Export Citation Format

Share Document