An Experimental Study of Mixed Convection in Vertical, Open-Ended, Concentric and Eccentric Annular Channels

2013 ◽  
Vol 135 (7) ◽  
Author(s):  
L. Maudou ◽  
G. H. Choueiri ◽  
S. Tavoularis
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Mixed Convection ◽  
Turbulent Flows ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Annular Channel ◽  
High Eccentricity ◽  
Convection Regime ◽  
Annular Channels

The effect of eccentricity on heat transfer in upward flow in a vertical, open-ended, annular channel with a diameter ratio of 0.61, an aspect ratio of 18:1, and both internal surfaces heated uniformly has been investigated experimentally. Results have been reported for eccentricities ranging from the concentric case to the near-contact case and three inlet bulk Reynolds numbers, equal approximately to 1500, 2800, and 5700. This work complements our recently reported experimental results on natural convection in the same facility. The present results are deemed to be largely in the mixed convection regime with some overlap with the forced convection regime and likely to include cases with laminar, transitional, and turbulent flows in at least a part of the test section. Small eccentricity had an essentially negligible effect on the overall heat transfer rate, but high eccentricity reduced the average heat transfer rate by up to 60%. High eccentricity also resulted in wall temperatures in the narrow gap region that were much higher than those in the open channel. The concentric-case Nusselt number was higher than the Dittus–Boelter prediction, whereas the highly eccentric-case Nusselt number was significantly lower than that.

Numerical simulation of water/alumina nanofluid mixed convection in square lid-driven cavity

2019 ◽  
Vol 30 (5) ◽  
pp. 2781-2807
Author(s):  
Davood Toghraie ◽  
Ehsan Shirani
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Mixed Convection ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Richardson Number ◽  
Hartmann Number ◽  
Two Phase ◽  
Content Type ◽  
Driven Cavity

Purpose The purpose of this paper is to investigate the mixed convection of a two-phase water–aluminum oxide nanofluid in a cavity under a uniform magnetic field. Design/methodology/approach The upper wall of the cavity is cold and the lower wall is warm. The effects of different values of Richardson number, Hartmann number, cavitation length and solid nanoparticles concentration on the flow and temperature field and heat transfer rate were evaluated. In this paper, the heat flux was assumed to be constant of 10 (W/m2) and the Reynolds number was assumed to be constant of 300 and the Hartmann number and the volume fraction of solid nanoparticles varied from 0 to 60 and 0 to 0.06, respectively. The Richardson number was considered to be 0.1, 1 and 5. Aspect ratios were 1, 1.5 and 2. Findings Comparison of the results of this paper with the results of the numerical and experimental studies of other researchers showed a good correlation. The results were presented in the form of velocity and temperature profiles, stream and isotherm lines and Nusselt numbers. The results showed that by increasing the Hartmann number, the heat transfer rate decreases. An increase from 0 to 20 in Hartmann number results in a 20 per cent decrease in Nusselt numbers, and by increasing the Hartmann number from 20 to 40, a 16 per cent decrease is observed in Nusselt number. Accordingly, it is inferred that by increasing the Hartmann number, the reduction in the Nusselt number is decreased. As the Richardson number increased, the heat transfer rate and, consequently, the Nusselt number increased. Therefore, an increase in the Richardson number results in an increase of the Nusselt number, that is, an increase in Richardson number from 0.1 to 1 and from 1 to 5 results in 37 and 47 per cent increase in Nusselt number, respectively. Originality/value Even though there have been numerous investigations conducted on convection in cavities under various configurations and boundary conditions, relatively few studies are conducted for the case of nanofluid mixed convection in square lid-driven cavity under the effect of magnetic field using two-phase model.

scholarly journals Numerical Study of Entropy Generation due to Coupled Laminar and Turbulent Mixed Convection and Thermal Radiation in an Enclosure Filled with a Semitransparent Medium

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
M. Goodarzi ◽  
M. R. Safaei ◽  
Hakan F. Oztop ◽  
A. Karimipour ◽  
E. Sadeghinezhad ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Mixed Convection ◽  
Turbulent Flow ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Numerical Study ◽  
Radiation Heat Transfer ◽  
Radiation Heat ◽  
Semitransparent Medium

The effect of radiation on laminar and turbulent mixed convection heat transfer of a semitransparent medium in a square enclosure was studied numerically using the Finite Volume Method. A structured mesh and the SIMPLE algorithm were utilized to model the governing equations. Turbulence and radiation were modeled with the RNGk-εmodel and Discrete Ordinates (DO) model, respectively. For Richardson numbers ranging from 0.1 to 10, simulations were performed for Rayleigh numbers in laminar flow (104) and turbulent flow (108). The model predictions were validated against previous numerical studies and good agreement was observed. The simulated results indicate that for laminar and turbulent motion states, computing the radiation heat transfer significantly enhanced the Nusselt number (Nu) as well as the heat transfer coefficient. Higher Richardson numbers did not noticeably affect the average Nusselt number and corresponding heat transfer rate. Besides, as expected, the heat transfer rate for the turbulent flow regime surpassed that in the laminar regime. The simulations additionally demonstrated that for a constant Richardson number, computing the radiation heat transfer majorly affected the heat transfer structure in the enclosure; however, its impact on the fluid flow structure was negligible.

scholarly journals Magnetohydrodynamic mixed convection in a nanofluid filled tubular enclosure

2020 ◽  
Vol 4 (1) ◽  
pp. 19-24
Author(s):  
Mohammad Mokaddes Ali
Keyword(s):  
Heat Transfer ◽  
Mixed Convection ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Temperature Fields ◽  
Convection Flow ◽  
Governing Equations ◽  
Convection Regime ◽  
Special Cases ◽  
Flow Domain

Mixed convection flow in a tubular enclosure filled with nanofluid in the presence of a magnetic field is numerically investigated in the present study. The bottom and top curved wall of the enclosure are respectively kept isothermally hot and cool while the remaining walls are insulated. The governing equations are formulated based on Boussinesq assumptions and solved with finite element method. The computation is carried out for mixed convection regime (0.1 ≤ Ri ≤ 10) and also natural convection regime (10 < Ri ≤ 100) with fixed values of remaining parameters. A detailed parametric discussion is presented for the physical properties of flow and temperature distributions in terms of streamlines, isotherms, average heat transfer rate within the flow domain. The results show that the flow and temperature fields affected by varying of pertinent parameters. Moreover, heat transfer rate is increased by 139.50% with the increase in Richardson number from 0.1 to 100. The increasing rate of heat transfer due to Ri is respectively decreased by 58.11% with varying of Ha from 0 to 60 and increased by 23.97% with the addition of nanoparticles up to 3%. Comparison is performed against the previously published results on the basis of special cases and found to be in excellent agreement.

An Experimental Study of Natural Convection in Vertical, Open-Ended, Concentric, and Eccentric Annular Channels

2011 ◽  
Vol 133 (12) ◽  
Author(s):  
G. H. Choueiri ◽  
S. Tavoularis
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Nusselt Number ◽  
Natural Convection ◽  
Heat Transfer Rate ◽  
Wall Temperature ◽  
Transfer Rate ◽  
Wall Heat Flux ◽  
Annular Channels ◽  
Cylindrical Annulus

The effects of eccentricity on the natural convection heat transfer from a vertical open-ended cylindrical annulus with diameter ratio of 1.63 and aspect ratio of 18:1 have been investigated experimentally. Within the range of present conditions, and with the possible exclusion of the highest eccentricities, it was found that the flow was thermally fully developed in a considerable section of the apparatus, as indicated by the linear variation of wall temperature with height. This made it possible to estimate the mass flow rate from the wall temperature gradient in the mid-section of the annulus, and use it to calculate the bulk Reynolds number, which was found to be weakly sensitive to eccentricity for a constant wall heat flux and to increase with increased wall heat flux. With the exception of the very low eccentricity range in which it was insensitive to eccentricity, the overall heat transfer rate diminished monotonically with increasing eccentricity. Plots of the local azimuthal variation of the Nusselt number showed that, at low eccentricities, the heat transfer rate increased near the wider gap but decreased near the narrower gap. The average Nusselt number was found to decrease measurably with increasing eccentricity and to increase slightly with increasing heat flux within the examined range. In contrast, the Grashof number was found to be much more sensitive to changes in heat flux and only had a weak dependence on eccentricity.

Heat Transfer Investigation of a Tube Partially Wrapped by Metal Porous Layer as a Potential Novel Tube for Air Cooled Heat Exchangers

2018 ◽  
Vol 141 (1) ◽  
Author(s):  
M. Mohammadpour-Ghadikolaie ◽  
M. Saffar-Avval ◽  
Z. Mansoori ◽  
N. Alvandifar ◽  
N. Rahmati
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Heat Transfer Rate ◽  
Porous Layer ◽  
Transfer Rate ◽  
Metal Foam ◽  
Convection Heat Transfer ◽  
Darcy Number ◽  
High Heat Transfer

Laminar forced convection heat transfer from a constant temperature tube wrapped fully or partially by a metal porous layer and subjected to a uniform air cross-flow is studied numerically. The main aim of this study is to consider the thermal performance of some innovative arrangements in which only certain parts of the tube are covered by metal foam. The combination of Navier–Stokes and Darcy–Brinkman–Forchheimer equations is applied to evaluate the flow field. Governing equations are solved using the finite volume SIMPLEC algorithm and the effects of key parameters such as Reynolds number, metal foam thermophysical properties, and porous layer thickness on the Nusselt number are investigated. The results show that using a tube which is fully wrapped by an external porous layer with high thermal conductivity, high Darcy number, and low drag coefficient, can provide a high heat transfer rate in the high Reynolds number laminar flow, increasing the Nusselt number almost as high as 16 times compared to a bare tube. The most important result of thisstudy is that by using some novel arrangements in which the tube is partially covered by the foam layer, the heat transfer rate can be increased at least 20% in comparison to the fully wrapped tube, while the weight and material usage can be considerably reduced.

scholarly journals Improved Energy Efficiency of Mixed Convection Heating Process in Eccentric Annulus

2021 ◽  
Vol 13 (8) ◽  
pp. 168781402110391
Author(s):  
Ben Abdelmlek Khaoula ◽  
Ben Nejma Fayçal
Keyword(s):  
Heat Transfer ◽  
Energy Efficiency ◽  
Rayleigh Number ◽  
Mixed Convection ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Rotation Speed ◽  
Numerical Study ◽  
Heating Process ◽  
Eccentric Annulus

This paper deals with a numerical study of mixed convection heat transfer in horizontal eccentric annulus. The inner cylinder is supposed hot and rotating, however the outer one is kept cold and motionless. The numerical problem was solved using COMSOL Multiphysics® which is based on finite element method. The resolution of the partial differential equations was conducted through an implicit scheme with the use of the damped Newton’s method. The present numerical analysis concerns the effect of eccentricity, rotation speed and Rayleigh number on the flow patterns, heat transfer rate, and energy efficiency of the process. It was found that the heat transfer rate increases with the increase of Rayleigh number. In addition, the heat transfer rate drops with the increase of rotation speed. Finally, we have demonstrated that maximum energy efficiency is achieved not only with higher Rayleigh number but also it is maximum with small eccentricity.

A comprehensive review on mixed convection for various patterns of kinematically and thermally induced scenarios within cavities

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Leo Lukose ◽  
Tanmay Basak
Keyword(s):  
Heat Transfer ◽  
Mixed Convection ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Inertial Forces ◽  
Content Type ◽  
Flow Interaction ◽  
Experimental Works ◽  
Solid Obstacles ◽  
S Model

Purpose The purpose of this paper is to address various works on mixed convection and proposes 10 unified models (Models 1–10) based on various thermal and kinematic conditions of the boundary walls, thermal conditions and/ or kinematics of objects embedded in the cavities and kinematics of external flow field through the ventilation ports. Experimental works on mixed convection have also been addressed. Design/methodology/approach This review is based on 10 unified models on mixed convection within cavities. Models 1–5 involve mixed convection based on the movement of single or double walls subjected to various temperature boundary conditions. Model 6 elucidates mixed convection due to the movement of single or double walls of cavities containing discrete heaters at the stationary wall(s). Model 7A focuses mixed convection based on the movement of wall(s) for cavities containing stationary solid obstacles (hot or cold or adiabatic) whereas Model 7B elucidates mixed convection based on the rotation of solid cylinders (hot or conductive or adiabatic) within the cavities enclosed by stationary or moving wall(s). Model 8 is based on mixed convection due to the flow of air through ventilation ports of cavities (with or without adiabatic baffles) subjected to hot and adiabatic walls. Models 9 and 10 elucidate mixed convection due to flow of air through ventilation ports of cavities involving discrete heaters and/or solid obstacles (conductive or hot) at various locations within cavities. Findings Mixed convection plays an important role for various processes based on convection pattern and heat transfer rate. An important dimensionless number, Richardson number (Ri) identifies various convection regimes (forced, mixed and natural convection). Generalized models also depict the role of “aiding” and “opposing” flow and combination of both on mixed convection processes. Aiding flow (interaction of buoyancy and inertial forces in the same direction) may result in the augmentation of the heat transfer rate whereas opposing flow (interaction of buoyancy and inertial forces in the opposite directions) may result in decrease of the heat transfer rate. Works involving fluid media, porous media and nanofluids (with magnetohydrodynamics) have been highlighted. Various numerical and experimental works on mixed convection have been elucidated. Flow and thermal maps associated with the heat transfer rate for a few representative cases of unified models [Models 1–10] have been elucidated involving specific dimensionless numbers. Originality/value This review paper will provide guidelines for optimal design/operation involving mixed convection processing applications.

scholarly journals Role of Rotating Cylinder toward Mixed Convection inside a Wavy Heated Cavity via Two-Phase Nanofluid Concept

Nanomaterials ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 1138 ◽  
Author(s):  
Ammar I. Alsabery ◽  
Mohammad Ghalambaz ◽  
Taher Armaghani ◽  
Ali Chamkha ◽  
Ishak Hashim ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Mixed Convection ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Rotating Cylinder ◽  
Alumina Nanoparticles ◽  
Optimum Number ◽  
Two Phase ◽  
Rotation Direction

The mixed convection two-phase flow and heat transfer of nanofluids were addressed within a wavy wall enclosure containing a solid rotating cylinder. The annulus area between the cylinder and the enclosure was filled with water-alumina nanofluid. Buongiorno’s model was applied to assess the local distribution of nanoparticles in the host fluid. The governing equations for the mass conservation of nanofluid, nanoparticles, and energy conservation in the nanofluid and the rotating cylinder were carried out and converted to a non-dimensional pattern. The finite element technique was utilized for solving the equations numerically. The influence of the undulations, Richardson number, the volume fraction of nanoparticles, rotation direction, and the size of the rotating cylinder were examined on the streamlines, heat transfer rate, and the distribution of nanoparticles. The Brownian motion and thermophoresis forces induced a notable distribution of nanoparticles in the enclosure. The best heat transfer rate was observed for 3% volume fraction of alumina nanoparticles. The optimum number of undulations for the best heat transfer rate depends on the rotation direction of the cylinder. In the case of counterclockwise rotation of the cylinder, a single undulation leads to the best heat transfer rate for nanoparticles volume fraction about 3%. The increase of undulations number traps more nanoparticles near the wavy surface.

3D optimization of baffle arrangement in a multi-phase nanofluid natural convection based on numerical simulation

2019 ◽  
Vol 30 (5) ◽  
pp. 2583-2605 ◽  
Author(s):  
Mohammad Mohsen Peiravi ◽  
Javad Alinejad ◽  
D.D. Ganji ◽  
Soroush Maddah
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Rayleigh Number ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Target Function ◽  
Optimal Arrangement ◽  
Content Type ◽  
Multi Phase

Purpose The purpose of this study is investigating the effect of using multi-phase nanofluids, Rayleigh number and baffle arrangement simultaneously on the heat transfer rate and Predict the optimal arrangement type of baffles in the differentiation of Rayleigh number in a 3D enclosure. Design/methodology/approach Simulations were performed on the base of the L25 Taguchi orthogonal array, and each test was conducted under different height and baffle arrangement. The multi-phase thermal lattice Boltzmann based on the D3Q19 method was used for modeling fluid flow and temperature fields. Findings Streamlines, isotherms, nanofluid volume fraction distribution and Nusselt number along the wall surface for 104 < Ra < 108 have been demonstrated. Signal-to-noise ratios have been analyzed to predict optimal conditions of maximize and minimize the heat transfer rate. The results show that by choosing the appropriate height and arrangement of the baffles, the average Nusselt number can be changed by more than 57 per cent. Originality/value The value of this paper is surveying three-dimensional and two-phase simulation for nanofluid. Also using the Taguchi method for Predicting the optimal arrangement type of baffles in a multi-part enclosure. Finally statistical analysis of the results by using of two maximum and minimum target Function heat transfer rates.

scholarly journals Mixed convective hybrid nanofluid flow in lid-driven undulated cavity: effect of MHD and Joule heating

2019 ◽  
Vol 16 (2) ◽  
pp. 109-126 ◽  
Author(s):  
Ishrat Zahan ◽  
R Nasrin ◽  
M A Alim
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Heat Transfer Rate ◽  
Joule Heating ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Hybrid Nanoparticles ◽  
Wave Number ◽  
Hybrid Nanofluid

A numerical analysis has been conducted to show the effects of magnetohydrodynamic (MHD) and Joule heating on heat transfer phenomenon in a lid driven triangular cavity. The heat transfer fluid (HTF) has been considered as water based hybrid nanofluid composed of equal quantities of Cu and TiO2 nanoparticles. The bottom wall of the cavity is undulated in sinusoidal pattern and cooled isothermally. The left vertical wall of the cavity is heated while the inclined side is insulated. The two dimensional governing partial differential equations of heat transfer and fluid flow with appropriate boundary conditions have been solved by using Galerkin's finite element method built in COMSOL Multyphysics. The effects of Hartmann number, Joule heating, number of undulation and Richardson number on the flow structure and heat transfer characteristics have been studied in details. The values of Prandtl number and solid volume fraction of hybrid nanoparticles have been considered as fixed. Also, the code validation has been shown. The numerical results have been presented in terms of streamlines, isotherms and average Nusselt number of the hybrid nanofluid for different values of governing parameters. The comparison of heat transfer rate by using hybrid nanofluid, Cu-water nanofluid,  TiO2 -water nanofluid and clear water has been also shown. Increasing wave number from 0 to 3 enhances the heat transfer rate by 16.89%. The enhanced rate of mean Nusselt number for hybrid nanofluid is found as 4.11% compared to base fluid.

Sign in / Sign up

Export Citation Format

Share Document