A Comparative Thermoeconomic Study of Hybrid Solar Gas-Turbine Power Plants

2013 ◽  
Vol 136 (1) ◽  
Author(s):  
James Spelling ◽  
Björn Laumert ◽  
Torsten Fransson
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Power Plants ◽  
First Generation ◽  
Combined Cycle ◽  
Parabolic Trough ◽  
Electricity Cost ◽  
Trade Offs ◽  
Solar Power Plants ◽  
Combined Cycles

The construction of the first generation of commercial hybrid solar gas-turbine power plants will present the designer with a large number of choices. To assist decision making, a thermoeconomic study has been performed for three different power plant configurations, namely, simple- and combined-cycles along with a simple-cycle with the addition of thermal energy storage. Multi-objective optimization has been used to identify Pareto-optimal designs and highlight the trade-offs between minimizing investment costs and minimizing specific CO2 emissions. The solar hybrid combined-cycle power plant provides a 60% reduction in electricity cost compared to parabolic trough power plants at annual solar shares up to 20%. The storage integrated designs can achieve much higher solar shares and provide a 7–13% reduction in electricity costs at annual solar shares up to 90%. At the same time, the water consumption of the solar gas-turbine systems is significantly lower than conventional steam-cycle based solar power plants.

A Comparative Thermoeconomic Study of Hybrid Solar Gas-Turbine Power Plants

2013 ◽  
Author(s):  
James Spelling ◽  
Björn Laumert ◽  
Torsten Fransson
Keyword(s):  
Gas Turbine ◽  
Power Plants ◽  
First Generation ◽  
Combined Cycle ◽  
Parabolic Trough ◽  
Electricity Cost ◽  
Trade Offs ◽  
Combined Cycle Plant ◽  
Solar Power Plants ◽  
Combined Cycles

The construction of the first generation of commercial hybrid solar gas-turbine power plants will present the designer with a large number of choices. To assist decision making, a thermoeconomic study has been performed for three different power plant configurations, namely simple- and combined-cycles as well as simple-cycle with the addition of thermal energy storage. Multi-objective optimization has been used to identify Pareto-optimal designs and highlight the trade-offs between minimizing investment costs and minimizing specific CO2 emissions. The solar hybrid combined-cycle plant provides a 60% reduction in electricity cost compared to parabolic trough power plants at annual solar shares up to 20%. The storage integrated designs can achieve much higher solar shares and provide a 7–13% reduction in electricity costs at annual solar shares up to 90%. At the same time, the water consumption of the solar gas-turbine systems is significantly lower than conventional steam-cycle based solar power plants.

Thermoeconomic Study of a Small Parabolic Trough Solar Plant

2010 ◽  
Author(s):  
M. D. Duran ◽  
E. A. Rinco´n ◽  
M. Sa´nchez
Keyword(s):  
Power Plant ◽  
Optimization Model ◽  
Power Plants ◽  
Optimization Problem ◽  
Pressure Level ◽  
Combined Cycle ◽  
Design Parameters ◽  
Parabolic Trough ◽  
Solar Plant ◽  
Solar Power Plants

This work describes the thermoeconomic study of an integrated combined cycle parabolic trough power plant. The parabolic trough plant will economize boiler activity, and thus the thermoeconomic optimization of the configuration of the boiler, including the parabolic trough plant, will be achieved. The objective is to obtain the optimum design parameters for the boiler and the size of the parabolic field. The proposal is to apply the methodology employed by Duran [1] and Valde´s et. al. [2], but with the inclusion of the parabolic trough plant into the optimization problem. It is important to point out that the optimization model be applied to a single pressure level configuration. For future works, it is proposed that the same model be applied to different configurations of integrated combined cycle solar power plants. As a result the optimum thermoeconomic design will be obtained for a parabolic trough plant used to economize the HRSG.

Enhancing the Economic Competitiveness of Concentrating Solar Power Plants Through an Innovative Integrated Solar-Combined Cycle With Thermal Energy Storage

2014 ◽  
Author(s):  
Rafael Guédez ◽  
James Spelling ◽  
Björn Laumert
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Power Plants ◽  
Solar Power ◽  
Cost Effective ◽  
Combined Cycle ◽  
Trade Offs ◽  
Effective Manner ◽  
Wide Range ◽  
Novel Concept

The present work deals with the thermoeconomic analysis of an innovative combined power cycle consisting of a molten-salt solar tower power plant with storage supported by additional heat provided from the exhaust of a topping gas-turbine unit. A detailed dynamic model has been elaborated using an in house simulation tool that simultaneously encompasses meteorological, demand and price data. A wide range of possible designs are evaluated in order to show the trade-offs between the objectives of achieving sustainable and economically competitive designs. Results show that optimal designs of the novel concept are a promising cost-effective hybrid option that can successfully fulfill both the roles of a gas peaker plant and a baseload solar power plant in a more effective manner. Moreover, designs are also compared against conventional combined cycle gas turbine power plants and it is shown that, under specific peaking operating strategies, the innovative concept can not only perform better from an environmental standpoint but also economically.

Power Augmentation Study of an Existing Combined Cycle Power Plant by Overspray Inlet Fogging

2008 ◽  
Author(s):  
Hsiao-Wei D. Chiang ◽  
Pai-Yi Wang ◽  
Hsin-Lung Li
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Power Plants ◽  
Peak Load ◽  
Combined Cycle ◽  
Ambient Conditions ◽  
Combined Cycle Power Plant ◽  
Combined Cycles ◽  
Increasing Demand

With increasing demand for power and with shortages envisioned especially during the peak load times during the summer, there is a need to boost gas turbine power. In Taiwan, most of gas turbines operate with combined cycle for base load. Only a small portion of gas turbines operates with simple cycle for peak load. To prevent the electric shortage due to derating of power plants in hot days, the power augmentation strategies for combined cycles need to be studied in advance. As a solution, our objective is to add an overspray inlet fogging system into an existing gas turbine-based combined cycle power plant (CCPP) to study the effects. Simulation runs were made for adding an overspray inlet fogging system to the CCPP under various ambient conditions. The overspray percentage effects on the CCPP thermodynamic performance are also included in this paper. Results demonstrated that the CCPP net power augmentation depends on the percentage of overspray under site average ambient conditions. This paper also included CCPP performance parametric studies in order to propose overspray inlet fogging guidelines for combined cycle power augmentation.

Enhancing the Economic Competitiveness of Concentrating Solar Power Plants Through an Innovative Integrated Solar-Combined Cycle With Thermal Energy Storage

2015 ◽  
Vol 137 (4) ◽  
Author(s):  
Rafael Guédez ◽  
James Spelling ◽  
Björn Laumert
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Power Plants ◽  
Solar Power ◽  
Cost Effective ◽  
Combined Cycle ◽  
Trade Offs ◽  
Effective Manner ◽  
Wide Range ◽  
Novel Concept

The present work deals with the thermo-economic analysis of an innovative combined power cycle consisting of a molten-salt solar tower power plant with storage supported by additional heat provided from the exhaust of a topping gas-turbine unit. A detailed dynamic model has been elaborated using an in house simulation tool that simultaneously encompasses meteorological, demand and price data. A wide range of possible designs are evaluated in order to show the trade-offs between the objectives of achieving sustainable and economically competitive designs. Results show that optimal designs of the novel concept are a promising cost-effective hybrid option that can successfully fulfill both the roles of a gas peaker plant and a baseload solar power plant in a more effective manner. Moreover, designs are also compared against conventional combined cycle gas turbine (CCGT) power plants and it is shown that, under specific peaking operating strategies (P-OSs), the innovative concept cannot only perform better from an environmental standpoint but also economically.

Optimal Gas-Turbine Design for Hybrid Solar Power Plant Operation

2012 ◽  
Author(s):  
James Spelling ◽  
Björn Laumert ◽  
Torsten Fransson
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Power Plants ◽  
Solar Power ◽  
Pressure Ratio ◽  
Inlet Temperature ◽  
Electricity Cost ◽  
Conflicting Objectives ◽  
Dynamic Simulation Model ◽  
A Minor

A dynamic simulation model of a hybrid solar gas-turbine power plant has been developed, allowing determination of its thermodynamic and economic performance. In order to examine optimum gas-turbine designs for hybrid solar power plants, multi-objective thermoeconomic analysis has been performed, with two conflicting objectives: minimum levelized electricity costs and minimum specific CO2 emissions. Optimum cycle conditions: pressure-ratio, receiver temperature, turbine inlet temperature and flow rate, have been identified for a 15 MWe gas-turbine under different degrees of solarization. At moderate solar shares, the hybrid solar gas-turbine concept was shown to provide significant water and CO2 savings with only a minor increase in the levelized electricity cost.

Analysis of Intermediate Temperature Combined Cycles With a Carbon Dioxide Topping Cycle

2008 ◽  
Author(s):  
R. Chacartegui ◽  
D. Sa´nchez ◽  
F. Jime´nez-Espadafor ◽  
A. Mun˜oz ◽  
T. Sa´nchez
Keyword(s):  
Carbon Dioxide ◽  
Power Plant ◽  
Gas Turbine ◽  
High Efficiency ◽  
Solar Power ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Pressure Drops ◽  
Combined Cycles ◽  
Topping Cycle

The development of high efficiency solar power plants based on gas turbine technology presents two problems, both of them directly associated with the solar power plant receiver design and the power plant size: lower turbine intake temperature and higher pressure drops in heat exchangers than in a conventional gas turbine. To partially solve these problems, different configurations of combined cycles composed of a closed cycle carbon dioxide gas turbine as topping cycle have been analyzed. The main advantage of the Brayton carbon dioxide cycle is its high net shaft work to expansion work ratio, in the range of 0.7–0.85 at supercritical compressor intake pressures, which is very close to that of the Rankine cycle. This feature will reduce the negative effects of pressure drops and will be also very interesting for cycles with moderate turbine inlet temperature (800–1000 K). Intercooling and reheat options are also considered. Furthermore, different working fluids have been analyzed for the bottoming cycle, seeking the best performance of the combined cycle in the ranges of temperatures considered.

Thermo-Economic Assessment Under Electrical Market Uncertainties of a Combined Cycle Gas Turbine Integrated With a Flue Gas-Condensing Heat Pump

2020 ◽  
Author(s):  
Alberto Vannoni ◽  
Andrea Giugno ◽  
Alessandro Sorce
Keyword(s):  
Power Plant ◽  
Power Systems ◽  
Gas Turbine ◽  
Heat Pump ◽  
Flue Gas ◽  
Power Plants ◽  
Greenhouse Gas Emission ◽  
Capital Expenditure ◽  
Combined Cycle ◽  
Gas Turbine Power Plant

Abstract Renewable energy penetration is growing, due to the target of greenhouse-gas-emission reduction, even though fossil fuel-based technologies are still necessary in the current energy market scenario to provide reliable back-up power to stabilize the grid. Nevertheless, currently, an investment in such a kind of power plant might not be profitable enough, since some energy policies have led to a general decrease of both the average price of electricity and its variability; moreover, in several countries negative prices are reached on some sunny or windy days. Within this context, Combined Heat and Power systems appear not just as a fuel-efficient way to fulfill local thermal demand, but also as a sustainable way to maintain installed capacity able to support electricity grid reliability. Innovative solutions to increase both the efficiency and flexibility of those power plants, as well as careful evaluations of the economic context, are essential to ensure the sustainability of the economic investment in a fast-paced changing energy field. This study aims to evaluate the economic viability and environmental impact of an integrated solution of a cogenerative combined cycle gas turbine power plant with a flue gas condensing heat pump. Considering capital expenditure, heat demand, electricity price and its fluctuations during the whole system life, the sustainability of the investment is evaluated taking into account the uncertainties of economic scenarios and benchmarked against the integration of a cogenerative combined cycle gas turbine power plant with a Heat-Only Boiler.

The Elephant in the Room–Gas Turbine Power

2010 ◽  
Vol 132 (12) ◽  
pp. 57-57
Author(s):  
Lee S. Langston
Keyword(s):  
Power Plant ◽  
Electric Power ◽  
Gas Turbine ◽  
Power Plants ◽  
Electrical Power ◽  
Electric Power Industry ◽  
Hydrocarbon Fuel ◽  
Combined Cycle ◽  
Electrical Generator ◽  
Gas Turbine Exhaust

This article presents an overview of gas turbine combined cycle (CCGT) power plants. Modern CCGT power plants are producing electric power as high as half a gigawatt with thermal efficiencies approaching the 60% mark. In a CCGT power plant, the gas turbine is the key player, driving an electrical generator. Heat from the hot gas turbine exhaust is recovered in a heat recovery steam generator, to generate steam, which drives a steam turbine to generate more electrical power. Thus, it is a combined power plant burning one unit of fuel to supply two sources of electrical power. Most of these CCGT plants burn natural gas, which has the lowest carbon content of any other hydrocarbon fuel. Their near 60% thermal efficiencies lower fuel costs by almost half compared to other gas-fired power plants. Their installed capital cost is the lowest in the electric power industry. Moreover, environmental permits, necessary for new plant construction, are much easier to obtain for CCGT power plants.

GTPRO: A Flexible, Interactive Computer Program for the Design and Optimization of Gas Turbine Power Systems

1988 ◽  
Author(s):  
Maher A. Elmasri
Keyword(s):  
Power Systems ◽  
Computer Program ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Combined Cycle ◽  
Process Flow ◽  
Technical Parameters ◽  
Design And Optimization ◽  
Trade Offs ◽  
Combined Cycles

A fast, interactive, flexible computer program has been developed to facilitate system selection and design for gas turbine based power and cogeneration plants. A data base containing ISO performance information on forty-two gas turbines is coupled to an off-design model to predict engine characteristics for different site and installation parameters. A heat recovery steam generator (HRSG) model allows boiler size and cost to be estimated as a function of the system’s technical parameters. The model can handle HRSG’s with up to two live steam pressures plus a third feedheating/deaerating drum. Five basic types of combined cycle are covered with up to four different process steam streams for cogeneration or gas turbine injection. Two additional feedheating steam bleeds are supported for condensing combined cycles. The program is intelligent with some internal decision making capabilities regarding process steam sourcing and flow directions and will automatically select the appropriate heat and mass balance procedures to cover a wide variety of process flow schematics. The program provides plotter outputs to show the cycle process flow schematic, T-s and h-s diagrams, and HRSG temperature profiles. An application of GTPRO in analyzing some technical and economic performance trade-offs for two-pressure combined cycles is presented.

Sign in / Sign up

Export Citation Format

Share Document