scholarly journals Vortex Dynamics in the Wake of Three Generic Types of Freestream Turbines

2017 ◽  
Vol 140 (2) ◽  
Author(s):  
Matthieu Boudreau ◽  
Guy Dumas
Keyword(s):  
Vortex Dynamics ◽  
Energy Recovery ◽  
Three Dimensional ◽  
Axial Flow ◽  
Navier Stokes ◽  
Mean Flow ◽  
Tip Vortices ◽  
The Mean ◽  
Optimal Efficiency ◽  
Oscillating Foil

An analysis of the vortex dynamics in the wake of three different freestream turbine concepts is conducted to gain a better understanding of the main processes affecting the energy recovery in their wakes. The turbine technologies considered are the axial-flow turbine (AFT), the crossflow turbine (CFT), also known as the H-Darrieus turbine, and the oscillating-foil turbine (OFT). The analysis is performed on single turbines facing a uniform oncoming flow and operating near their optimal efficiency conditions at a Reynolds number of 107. Three-dimensional (3D) delayed detached-eddy simulations (DDES) are carried out using a commercial finite volume Navier–Stokes solver. It is found that the wake dynamics of the AFT is significantly affected by the triggering of an instability, while that of the CFT and the OFT are mainly governed by the mean flow field stemming from the tip vortices' induction.

Improved κ-ɛ Modelling of Impeller Flow Performance of a Mixed-Flow Pump under off-Design Operating States

1993 ◽  
Vol 207 (4) ◽  
pp. 219-229 ◽  
Author(s):  
S M Fraser ◽  
Y Zhang
Keyword(s):  
Stokes Equations ◽  
Three Dimensional ◽  
Careful Analysis ◽  
Navier Stokes ◽  
Mean Flow ◽  
Mixed Flow ◽  
Navier Stokes Equations ◽  
Flow Through ◽  
The Mean ◽  
Flow Pump

Three-dimensional turbulent flow through the impeller passage of a model mixed-flow pump has been simulated by solving the Navier-Stokes equations with an improved κ-ɛ model. The standard κ-ɛ model was found to be unsatisfactory for solving the off-design impeller flow and a converged solution could not be obtained at 49 per cent design flowrate. After careful analysis, it was decided to modify the standard κ-ɛ model by including the extra rates of strain due to the acceleration of impeller rotation and geometrical curvature and removing the mathematical ill-posedness between the mean flow turbulence modelling and the logarithmic wall function.

Twin Inclined Circular Jets Evolution Through a Cool Crossflow

2007 ◽  
Author(s):  
Amina Radhouane ◽  
Nejla Mahjoub Sai¨d ◽  
Hatem Mhiri ◽  
George Lepalec ◽  
Philippe Bournot
Keyword(s):  
Stokes Equations ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Mean Flow ◽  
Navier Stokes Equations ◽  
Vortical Structures ◽  
Circular Jets ◽  
Turbulent Closure ◽  
The Mean ◽  
Good Agreement

The aim of this paper is to examine experimentally as well as numerically the flowfield resulting from the interaction between a twin circular inclined hot jets emerging into a cooling crossflow. The resulting flowfield is quite complex due to the presence of different vortical structures including the kidney vortex, the horse-shoe vortex, etc... The evolution of the twin inclined jets through the crossflow could be depicted by tracking the mean-flow velocity field and its associated turbulence statistics by means of the PIV technique. This evolution can be influenced by many factors. Herein, we will deal with that resulted by the injection nozzles’ inclination and the jets’ spacing. Then, we performed a three dimensional sample of the studied configuration in order to simulate the evolution of the resulting flowfield. For that, the Navier Stokes equations were simulated with an RSM second order turbulent closure model. Then a non uniform meshing was applied. A good agreement was obtained between the experimental data and the numerical modeling. After validation we could represent in addition to the available results, the temperature distribution and the effects the variation of the injection inclination and that of the jets’ spacing bring on it (on its spatial evolution).

scholarly journals Three-Dimensional Navier-Stokes Computation of Turbine Nozzle Flow With Advanced Turbulence Models

1995 ◽  
Author(s):  
J. Luo ◽  
B. Lakshminarayana
Keyword(s):  
Reynolds Stress ◽  
Three Dimensional ◽  
Turbulence Models ◽  
Reynolds Stress Model ◽  
Navier Stokes ◽  
Nozzle Flow ◽  
Stress Model ◽  
Mean Flow ◽  
The Mean ◽  
Algebraic Reynolds Stress Model

A three-dimensional Navier-Stokes procedure has been used to compute the three-dimensional viscous flow through the turbine nozzle passage of a single stage turbine. A low Reynolds number k-ε model and a zonal k-ε/ARSM (algebraic Reynolds stress model) are utilized for turbulence closure. The algebraic Reynolds stress model is used only in the endwall region to represent the anisotropy of turbulence. A four-stage Runge-Kutta scheme is used for time-integration of both the mean-flow and the turbulence transport equations. For the turbine nozzle flow, comprehensive comparisons between the predictions and the experimental data obtained at Penn State show that most features of the vortex-dominated endwall flow, as well as nozzle wake structure, have been captured well by the numerical procedure. An assessment of the performance of the turbulence models has been carried out The two models are found to provide similar predictions for the mean flow parameters, although slight improvement in the prediction of some secondary flow quantities has been obtained by the ARSM model.

Three-Dimensional Navier–Stokes Computation of Turbine Nozzle Flow With Advanced Turbulence Models

1997 ◽  
Vol 119 (3) ◽  
pp. 516-530 ◽  
Author(s):  
J. Luo ◽  
B. Lakshminarayana
Keyword(s):  
Reynolds Stress ◽  
Three Dimensional ◽  
Turbulence Models ◽  
Reynolds Stress Model ◽  
Navier Stokes ◽  
Nozzle Flow ◽  
Stress Model ◽  
Mean Flow ◽  
The Mean ◽  
Algebraic Reynolds Stress Model

A three-dimensional Navier–Stokes procedure has been used to compute the three-dimensional viscous flow through the turbine nozzle passage of a single-stage turbine. A low-Reynolds-number k–ε model and a zonal k-ε/ARSM (algebraic Reynolds stress model) are utilized for turbulence closure. The algebraic Reynolds stress model is used only in the endwall region to represent the anisotropy of turbulence. A four-stage Runge–Kutta scheme is used for time integration of both the mean-flow and the turbulence transport equations. For the turbine nozzle flow, comprehensive comparisons between the predictions and the experimental data obtained at Penn State show that most features of the vortex-dominated endwall flow, as well as nozzle wake structure, have been captured well by the numerical procedure. An assessment of the performance of the turbulence models has been carried out. The two models are found to provide similar predictions for the mean flow parameters, although slight improvement in the prediction of some secondary flow quantities has been obtained by the ARSM model.

scholarly journals Modeling the 3-d flow around a cylinder using the SAS hybrid model

2014 ◽  
Vol 16 (5) ◽  
pp. 901-918 ◽  
Keyword(s):  
Turbulence Modeling ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Cross Flow ◽  
Numerical Code ◽  
Navier Stokes ◽  
Computational Domain ◽  
Mean Flow ◽  
Unstable Flow ◽  
Vortex Size

<div> <p>Three-dimensional calculations were performed to simulate the flow around a cylindrical vegetation element using the Scale Adaptive Simulation (SAS) model; commonly, this is the first step of the modeling of the flow through multiple vegetation elements. SAS solves the Reynolds Averaged Navier-Stokes equations in stable flow regions, while in regions with unstable flow it goes unsteady producing a resolved turbulent spectrum after reducing eddy viscosity according to the locally resolved vortex size represented by the von Karman length scale. A finite volume numerical code was used for the spatial discretisation of the rectangular computational domain with stream-wise, cross-flow and vertical dimensions equal to 30D, 11D and 1D, respectively, which was resolved with unstructured grids. Calculations were compared with experiments and Large Eddy Simulations (LES). Predicted overall flow parameters and mean flow velocities exhibited a very satisfactory agreement with experiments and LES, while the agreement of predicted turbulent stresses was satisfactory. Calculations showed that SAS is an efficient and relatively fast turbulence modeling approach, especially in relevant practical problems, in which the very high accuracy that can be achieved by LES at the expense of large computational times is not required.</p> </div> <p>&nbsp;</p>

Three-Dimensional Navier-Stokes Analysis of Turbine Rotor and Tip-Leakage Flowfield

1997 ◽  
Author(s):  
J. Luo ◽  
B. Lakshminarayana
Keyword(s):  
Three Dimensional ◽  
Turbine Rotor ◽  
Secondary Flows ◽  
Tip Clearance ◽  
Navier Stokes ◽  
Leakage Flow ◽  
Mean Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Blade Tip

The 3-D viscous flowfield in the rotor passage of a single-stage turbine, including the tip-leakage flow, is computed using a Navier-Stokes procedure. A grid-generation code has been developed to obtain embedded H grids inside the rotor tip gap. The blade tip geometry is accurately modeled without any “pinching”. Chien’s low-Reynolds-number k-ε model is employed for turbulence closure. Both the mean-flow and turbulence transport equations are integrated in time using a four-stage Runge-Kutta scheme. The computational results for the entire turbine rotor flow, particularly the tip-leakage flow and the secondary flows, are interpreted and compared with available data. The predictions for major features of the flowfield are found to be in good agreement with the data. Complicated interactions between the tip-clearance flows and the secondary flows are examined in detail. The effects of endwall rotation on the development and interaction of secondary and tip-leakage vortices are also analyzed.

scholarly journals Self-consistent triple decomposition of the turbulent flow over a backward-facing step under finite amplitude harmonic forcing

2019 ◽  
Vol 475 (2225) ◽  
pp. 20190018
Author(s):  
E. Yim ◽  
P. Meliga ◽  
F. Gallaire
Keyword(s):  
Turbulent Flow ◽  
Finite Amplitude ◽  
Navier Stokes ◽  
Reynolds Stresses ◽  
Mean Flow ◽  
Backward Facing Step ◽  
Eddy Viscosity Model ◽  
Coherent Interaction ◽  
Self Consistent ◽  
The Mean

We investigate the saturation of harmonically forced disturbances in the turbulent flow over a backward-facing step subjected to a finite amplitude forcing. The analysis relies on a triple decomposition of the unsteady flow into mean, coherent and incoherent components. The coherent–incoherent interaction is lumped into a Reynolds averaged Navier–Stokes (RANS) eddy viscosity model, and the mean–coherent interaction is analysed via a semi-linear resolvent analysis building on the laminar approach by Mantič-Lugo & Gallaire (2016 J. Fluid Mech. 793 , 777–797. ( doi:10.1017/jfm.2016.109 )). This provides a self-consistent modelling of the interaction between all three components, in the sense that the coherent perturbation structures selected by the resolvent analysis are those whose Reynolds stresses force the mean flow in such a way that the mean flow generates exactly the aforementioned perturbations, while also accounting for the effect of the incoherent scale. The model does not require any input from numerical or experimental data, and accurately predicts the saturation of the forced coherent disturbances, as established from comparison to time-averages of unsteady RANS simulation data.

Aerodynamic Design Optimization of an Axial Flow Compressor Rotor

2002 ◽  
Author(s):  
Chan-Sol Ahn ◽  
Kwang-Yong Kim
Keyword(s):  
Design Optimization ◽  
Response Surface ◽  
Computing Time ◽  
Flow Analysis ◽  
Three Dimensional ◽  
Axial Flow ◽  
Navier Stokes ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Design Variables

Design optimization of a transonic compressor rotor (NASA rotor 37) using the response surface method and three-dimensional Navier-Stokes analysis has been carried out in this work. The Baldwin-Lomax turbulence model was used in the flow analysis. Three design variables were selected to optimize the stacking line of the blade. Data points for response evaluations were selected by D-optimal design, and linear programming method was used for the optimization on the response surface. As a main result of the optimization, adiabatic efficiency was successfully improved. It was found that the optimization process provides reliable design of a turbomachinery blade with reasonable computing time.

scholarly journals Three-Dimensional Turbulent Vortex Shedding From a Surface-Mounted Square Cylinder: Predictions With Large-Eddy Simulations and URANS

2014 ◽  
Vol 136 (6) ◽  
Author(s):  
B. A. Younis ◽  
A. Abrishamchi
Keyword(s):  
Experimental Data ◽  
Turbulence Model ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Large Eddy Simulations ◽  
Navier Stokes ◽  
Reynolds Stresses ◽  
Mean Flow ◽  
Navier Stokes Equations ◽  
Large Eddy

The paper reports on the prediction of the turbulent flow field around a three-dimensional, surface mounted, square-sectioned cylinder at Reynolds numbers in the range 104–105. The effects of turbulence are accounted for in two different ways: by performing large-eddy simulations (LES) with a Smagorinsky model for the subgrid-scale motions and by solving the unsteady form of the Reynolds-averaged Navier–Stokes equations (URANS) together with a turbulence model to determine the resulting Reynolds stresses. The turbulence model used is a two-equation, eddy-viscosity closure that incorporates a term designed to account for the interactions between the organized mean-flow periodicity and the random turbulent motions. Comparisons with experimental data show that the two approaches yield results that are generally comparable and in good accord with the experimental data. The main conclusion of this work is that the URANS approach, which is considerably less demanding in terms of computer resources than LES, can reliably be used for the prediction of unsteady separated flows provided that the effects of organized mean-flow unsteadiness on the turbulence are properly accounted for in the turbulence model.

Experimental Study of Flow Inside a Centrifugal Fan Using Magnetic Resonance Velocimetry

2019 ◽  
Author(s):  
Davis W. Hoffman ◽  
Laura Villafañe ◽  
Christopher J. Elkins ◽  
John K. Eaton
Keyword(s):  
Three Dimensional ◽  
Leading Edge ◽  
Suction Side ◽  
Reynolds Numbers ◽  
Centrifugal Fan ◽  
Mean Flow ◽  
Magnetic Resonance Velocimetry ◽  
Flow Features ◽  
Outlet Flow ◽  
The Mean

Abstract Three-dimensional, three-component time-averaged velocity fields have been measured within a low-speed centrifugal fan with forward curved blades. The model investigated is representative of fans commonly used in automotive HVAC applications. The flow was analyzed at two Reynolds numbers for the same ratio of blade rotational speed to outlet flow velocity. The flow patterns inside the volute were found to have weak sensitivity to Reynolds number. A pair of counter-rotating vortices evolve circumferentially within the volute with positive and negative helicity in the upper and lower regions, respectively. Measurements have been further extended to capture phase-resolved flow features by synchronizing the data acquisition with the blade passing frequency. The mean flow field through each blade passage is presented including the jet-wake structure extending from the blade and the separation zone on the suction side of the blade leading edge.

Sign in / Sign up

Export Citation Format

Share Document