Research on Improving the Dynamic Performance of Centrifugal Pumps With Twisted Gap Drainage Blades

2019 ◽  
Vol 141 (9) ◽  
Author(s):  
Zheng-Chuan Zhang ◽  
Hong-Xun Chen ◽  
Zheng Ma ◽  
Jian-Wu He ◽  
Hui Liu ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Centrifugal Pump ◽  
Dynamic Characteristics ◽  
Dynamic Performance ◽  
Three Dimensional ◽  
Hydraulic Performance ◽  
Operating Conditions ◽  
Navier Stokes ◽  
Centrifugal Pumps ◽  
Practical Applications

Through numerical simulation and experiments analysis, it is indicated that the hydraulic and anticavitation performance of a centrifugal pump with twisted gap drainage blades based on flow control theory can be significantly improved under certain operating conditions. In order to introduce the technology of gap drainage to practical applications, we put forward the parameter formulas of the twisted gap drainage blade to design three-dimensional new type blade, which are also proved to be effective for enhancing the dynamic characteristics of the centrifugal pump. Furthermore, a practical centrifugal pump is redesigned to be a twisted gap drainage impeller with the same structure size as the original impeller, and the nonlinear hybrid Reynolds-averaged Navier–Stokes (RANS)/large eddy simulation (LES) method is employed to simulate the hydraulic dynamic characteristics. Numerical simulation results show that the hydraulic performance and dynamic characteristics of the redesigned impeller centrifugal pump are significantly enhanced. In experiments, the twisted gap drainage blades structure not only remarkably improves the hydraulic performance and the pressure pulsation characteristics of the centrifugal pump but also reduces the vibration intensity.

Health Monitoring of Centrifugal Pumps Using Digital Models

2019 ◽  
Vol 141 (9) ◽  
Author(s):  
Amr A. Abdel Fatah ◽  
Mohammed A. Hassan ◽  
Mohamed Lotfy ◽  
Antoine S. Dimitri
Keyword(s):  
Centrifugal Pump ◽  
Fluid Dynamic ◽  
Rapid Development ◽  
Dynamic Performance ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Normal Operation ◽  
Centrifugal Pumps ◽  
Digital Models ◽  
Exciting Forces

The area of predictive maintenance (PM) has received growing research interest in the past few years. Diagnostic capabilities of PM technologies have increased due to advances made in sensor technologies, signal processing algorithms, and the rapid development of computational power and data handling algorithms. Conventional PM programs are mostly built around analyzing sensors' data collected from physical systems. Incorporating simulation data collected from digital models replicating the physical system with sensors' data can lead to more optimization for operation and maintenance. This paper demonstrates the role of using digital models in implementing effective condition monitoring on centrifugal pumps. Two digital models are used to study the dynamic performance of a centrifugal pump experiencing cavitation condition. The first model is a three-dimensional fully turbulent computational fluid dynamic (CFD) model. Based on the pressure distribution obtained from the CFD, a novel analytical pressure pulsation model is developed and used to simulate the exciting forces affecting the pump. The second digital model is a pump casing dynamic model which is used to predict the casing vibration response to exciting forces due to faulty operating conditions. Results obtained from the digital models are validated using an experimental test rig of a small centrifugal pump. Using this concept, a pump faulty operation can be simulated to provide complete understanding of the root cause of the fault. Additionally, digital models can be used to simulate different corrective actions that would restore the normal operation of the pump.

Numerical Investigations and Performance Experiments of a Deep-Well Centrifugal Pump With Different Diffusers

2012 ◽  
Vol 134 (7) ◽  
Author(s):  
Ling Zhou ◽  
Weidong Shi ◽  
Weigang Lu ◽  
Bo Hu ◽  
Suqing Wu
Keyword(s):  
Numerical Simulation ◽  
Centrifugal Pump ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Hydrodynamic Performance ◽  
Navier Stokes ◽  
Deep Well ◽  
Static Pressure Distribution ◽  
And Performance

In this paper, the design methodology of a new type of three-dimensional surface return diffuser (3DRD) is presented and described in detail. The main goal was to improve the hydrodynamic performance of the deep-well centrifugal pump (DCP). During this study, a two-stage DCP equipped with two different type diffusers was simulated employing the commercial computational fluid dynamics (CFD) software ANYSY-Fluent to solve the Navier-Stokes equations for three-dimensional steady flow. A sensitivity analysis of the numerical model was performed in order to impose appropriate parameters regarding grid elements number and turbulence model. The flow field and the static pressure distribution in the diffusers obtained by numerical simulation were analyzed, and the diffuser efficiency was defined to quantify the pressure conversion capability. The prototype experimental test results were acquired and compared with the data predicted from the numerical simulation, which showed that the performance of the pump with 3DRD is better than that of the traditional cylindrical return diffuser (CRD) under all operating conditions. The efficiency and single-stage head of the pump with 3DRD have been significantly improved compared with the standard DCP of the same class.

The Research on Numerical Simulation of the Centrifugal Pump and Configuration Perfected

2013 ◽  
Vol 694-697 ◽  
pp. 56-60
Author(s):  
Yue Jun Ma ◽  
Ji Tao Zhao ◽  
Yu Min Yang
Keyword(s):  
Numerical Simulation ◽  
Centrifugal Pump ◽  
Unstructured Grid ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Internal Flow ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Flow Phenomena ◽  
Simplec Algorithm

In the paper, on the basis of three-dimensional Reynolds-averaged Navier-Stokes equations and the RNG κ-ε turbulence model, adopting Three-dimensional unstructured grid and pressure connection the implicit correction SIMPLEC algorithm, and using MRF model which is supported by Fluent, this paper carries out numerical simulation of the internal flow of the centrifugal pump in different operation points. According to the results of numerical simulation, this paper analyzes the bad flow phenomena of the centrifugal pump, and puts forward suggests about configuration perfected of the centrifugal pump. In addition, this paper is also predicted the experimental value of the centrifugal pump performance, which is corresponding well with the measured value.

scholarly journals Investigation on the Handling Ability of Centrifugal Pumps under Air–Water Two-Phase Inflow: Model and Experimental Validation

Energies ◽  
2018 ◽  
Vol 11 (11) ◽  
pp. 3048 ◽  
Author(s):  
Qiaorui Si ◽  
Gérard Bois ◽  
Qifeng Jiang ◽  
Wenting He ◽  
Asad Ali ◽  
...  
Keyword(s):  
Centrifugal Pump ◽  
Two Phase Flow ◽  
Bubbly Flow ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Phase Flow ◽  
Centrifugal Pumps ◽  
Flow Conditions ◽  
Two Phase ◽  
Local Flow

The paper presents experimental and numerical investigations performed on a single stage, single-suction, horizontal-orientated centrifugal pump in air–water two-phase non-condensable flow conditions. Experimental measurements are performed in a centrifugal pump using pressure sensor devices in order to measure the wall static pressures at the inlet and outlet pump sections for different flow rates and rotational speeds combined with several air void fraction (a) values. Two different approaches are used in order to predict the pump performance degradations and perform comparisons with experiments for two-phase flow conditions: a one-dimensional two-phase bubbly flow model, and a full “Three-Dimensional Unsteady Reynolds Average Navier–Stokes” (3D-URANS) simulation using a modified k-epsilon turbulence model combined with the Euler–Euler inhomogeneous two-phase flow description. The overall and local flow features are presented and analyzed. Limitations concerning both approaches are pointed out according to some flow physical assumptions and measurement accuracies. Some additional suggestions are proposed in order to improve two-phase flow pump suction capabilities.

Numerical and Experimental Study of Axial Force and Hydraulic Performance in a Deep-Well Centrifugal Pump With Different Impeller Rear Shroud Radius

2013 ◽  
Vol 135 (10) ◽  
Author(s):  
Ling Zhou ◽  
Weidong Shi ◽  
Wei Li ◽  
Ramesh Agarwal
Keyword(s):  
Centrifugal Pump ◽  
Axial Force ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Hydraulic Performance ◽  
Navier Stokes ◽  
Computational Domain ◽  
Pump Performance ◽  
Deep Well ◽  
Static Pressure Distribution

A multistage deep-well centrifugal pump (DCP) with different impeller rear shroud radius have been investigated both numerically and experimentally under multiconditons, which aims at studying the influence of impeller rear shroud radius to the axial force and pump hydraulic performance. During this study, a two-stage DCP equipped with three different impellers was simulated employing the commercial computational fluid dynamics (CFD) software ANYSY-Fluent to solve the Navier-Stokes equations for three-dimensional steady flow. High-quality structured grids were meshed on the whole computational domain. Test results were acquired by prototype experiments, and then compared with the predicted pump performance and axial force. The static pressure distribution in the pump passage obtained by numerical simulation was analyzed. The results indicated that the appropriate impeller rear shroud radius could improve the pump performance and lower the axial force significantly.

Effect of Baffles in Between Stages on Performance and Flow Characteristics of a Two-Stage Split Case Centrifugal Pump

2017 ◽  
Author(s):  
Yiyun Wang ◽  
Ji Pei ◽  
Shouqi Yuan ◽  
Wenjie Wang
Keyword(s):  
Centrifugal Pump ◽  
High Efficiency ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Internal Flow ◽  
Production Method ◽  
Navier Stokes ◽  
Centrifugal Pumps ◽  
Two Stage

Two-stage split case centrifugal pumps play an important role in large flow rate and high lift water transfer situations. To investigate the influence of baffles in between stages on the performance and internal flow characteristics, the unsteady simulations for the prototype pump were carried out by solving the three-dimensional Reynolds-averaged Navier-Stokes equations with a shear stress transport (SST) turbulence model. The structured grids were generated for the whole flow passage. The calculated performance results were verified by the experimental measurements. The entropy production method based on numerical simulation was applied to analyze the distribution and mechanism of flow losses. The results show that the turbulence dissipation is the dominant flow loss, and the viscous dissipation can be neglected. The baffles can reduce the turbulence dissipation power obviously and can improve the hydraulic efficiency by maximum 5%, especially under QBEP and over-load conditions. The baffles have the greatest effect on the hydraulic losses in the double suction impeller., because they change the flow characteristics in the channels between the first stage impeller and the double suction impeller, affecting the inflow condition dramatically for the impeller. The study can give a reference to optimize the design of the two-stage split case centrifugal pump for high efficiency.

scholarly journals ANALYSIS OF THE IMPACT OF SPECIAL CONSTRUCTIONS OF GAP SEALS ON THE DYNAMICS OF CENTRIFUGAL MACHINES

ScienceRise ◽  
2020 ◽  
pp. 3-13
Author(s):  
Serhii Shevchenko
Keyword(s):  
Dynamic Characteristics ◽  
High Speed ◽  
Dynamic Properties ◽  
Dynamic Performance ◽  
Operating Conditions ◽  
Centrifugal Pumps ◽  
Labyrinth Seals ◽  
Research Results ◽  
The Impact ◽  
Technological Product

The object of research: the influence of the design features of special gap seals on the dynamic characteristics of centrifugal machines. Investigated problem: harmonization of the consumption and dynamic characteristics of the seals of the rotors of high-speed machines by applying special design methods. Main scientific results: The mechanism and operating conditions of seals with floating rings are described. It is determined that the most effective from the point of view of dynamic characteristics is the variant of the semi-movable ring. Expressions for determining the conditions of angular and radial immobility of a floating ring are obtained. The design options for deformable gap seals, including deformable floating rings, deformable interwheel seals and seals with an axially movable deformable sleeve, have been investigated. The scope of their application for unique machines with high requirements for tightness and vibration reliability has been determined. Variants of the design of labyrinth seals have been investigated. The analysis shows that the dynamic properties of labyrinth seals significantly depend on the relative position of the ridges. Overlapping ridged seals have the worst dynamic performance of the labyrinth seal designs. The honeycomb seal has more favorable dynamic properties, and the well seal has the best combination of consumption and dynamic characteristics. The dynamic characteristics are especially important for the seals of high-speed rotors of centrifugal machines. The area of practical use of the research results: Enterprises that manufacture centrifugal machines: pumps and compressors. Innovative technological product: a methodology for the selection, design and calculation of special designs of gap seals with optimization of dynamic and flow characteristics. Scope of application of the innovative technological product: The obtained research results will be useful in the design and manufacture of centrifugal pumps and compressors for any parameters.

Study on Numerical Simulation and Performance Test of Tubular Pumping System

2013 ◽  
Author(s):  
Yan Jin ◽  
Chao Liu ◽  
Li Cheng
Keyword(s):  
Numerical Simulation ◽  
Optimization Design ◽  
Performance Test ◽  
High Efficiency ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Navier Stokes ◽  
Rotating Speed ◽  
Pumping System

Research on three-dimensional flow field in a tubular pumping system using numerical simulation based on the Reynolds time-averaged Navier-Stokes equations and the RNG k–ε turbulent model. By using this method, the performance of pumping system such as head, shaft power and efficiency are predicted based on the calculation of different operating conditions in the discharge range from 20L/s to 35L/s at the same rotating speed. For verifying the accuracy and reliability of the calculation results, a tubular pumping system bedstand is designed for the permarmance test. The comparison of simulation results and the experiment data shown that the calculation performances close agreement with the experiment results in the high efficiency area, but in the condition of large discharge and low discharge, deviations were existed between the two results. Combining with the results of numerical simulation and experiment, which can provide more evidences for the hydraulic performances prediction and optimization design of pumping system.

Numerical Simulation and Experimental Study on Hydraulic Performance of Centrifugal Pump's Impeller Based on FINE

2013 ◽  
Vol 444-445 ◽  
pp. 390-394
Author(s):  
Yong Shang ◽  
Xiao Bing Liu ◽  
Xue Jun Yu
Keyword(s):  
Numerical Simulation ◽  
Centrifugal Pump ◽  
Flow Rate ◽  
Flow Analysis ◽  
Three Dimensional ◽  
Hydraulic Performance ◽  
Test Results ◽  
Turbulent Model ◽  
Three Dimensional Flow ◽  
Dimensional Flow

By using the FINE software developed by NUMECA Company, the hydraulic performance of the impeller of a centrifugal pump with spatial guide vanes was numerically simulated. The S-A turbulent model was used to numerically calculate the three-dimensional flow field in the centrifugal pump under three different conditions. The flow analysis shows that the pressure gradient on the vane surface gradually reduces with the increasing of the flow rate; the position of axial vortex between vanes has nothing to do with the flow rate; the tangential flow gradient in the flow passage decreases with the increasing of the flow rate. Compared with the test results, it is obvious that this numerical simulation can accurately predicate the complicated three-dimensional flow and the hydraulic performance of the pump.

Enhancing the Performance of Centrifugal Pump by Adding Cylindrical Disks at Inlet Suction

2019 ◽  
Author(s):  
Linda Sadik ◽  
Badih Jawad ◽  
Munther Y. Hermez ◽  
Liping Liu
Keyword(s):  
Numerical Simulation ◽  
Secondary Flow ◽  
Centrifugal Pump ◽  
Three Dimensional ◽  
Low Flow ◽  
Pump Efficiency ◽  
Centrifugal Pumps ◽  
Flow Rates ◽  
Pump Performance ◽  
Suction Performance

Abstract Optimizing the high efficiency design of centrifugal pumps requires a detailed understanding of the internal flow. The prediction of the flow inside the pump can be acquired by understanding the rotatory motion and the three-dimensional shape of the impellers, as well as its fundamental unsteady behavior. The flow inside a centrifugal pump is three-dimensional, unsettled and always associated with secondary flow structures. When a centrifugal pump operates under low flow rates, a secondary flow, known as recirculation, starts to begin. Inside this, the separation of flow increases, which creates vortices and cause local pressure to decrease, which induces cavitation. This phenomenon of recirculation will increase the Net Positive Suction Head Required (NPSHR). Improving the suction performance continues to remain a vital and continuous topic in the development and application of centrifugal pumps. In this research, the focal point is to enhance the pump suction performance under low flow rates by modifying the impeller design. This research entails a numerical simulation investigation on the addition of three different designs, each consisting of two cylindrical disks at the impeller inlet suction. It is hypothesized that these modifications will assist suppressing the recirculation phenomenon. The turbulent flow within the centrifugal pump was analyzed by applying the Reynolds-Averaged Navier-Stokes equations and the k–ϵ equations for turbulence modelling. The computational domain consists of the inlet, impeller, diffuser and outlet. Analysis of ΔP, torque data and pump efficiency was conducted. The application of CFD solvers to predict pump performance resulted in reduced prices for testing as well as pump development time. The numerical simulation concluded that placing 3-D multi-cylindrical disks at the impeller inlet section improved the centrifugal pump performance under low flow rates. The model design 1 resulted in a pump efficiency improvement of about 5% at low flow rates by lowering the amount of flow leaking back (re-circulation) through the internal suction.

Sign in / Sign up

Export Citation Format

Share Document