Design of Tool for Exfoliation of Monocrystalline Microscale Silicon Films

2019 ◽  
Vol 7 (1) ◽  
Author(s):  
Martin Ward ◽  
Michael Cullinan
Keyword(s):  
Thin Film ◽  
Surface Roughness ◽  
Flexible Electronics ◽  
High Performance ◽  
Single Crystal Silicon ◽  
Complementary Metal Oxide Semiconductor ◽  
Metal Oxide Semiconductor ◽  
Oxide Semiconductor ◽  
Crystal Silicon ◽  
Electronic Products

This paper presents the development of a prototype exfoliation tool and process for the fabrication of thin-film, single crystal silicon, which is a key material for creating high-performance flexible electronics. The process described in this paper is compatible with traditional wafer-based, complementary metal–oxide–semiconductor (CMOS) fabrication techniques, which enables high-performance devices fabricated using CMOS processes to be easily integrated into flexible electronic products like wearable or internet of things devices. The exfoliation method presented in this paper uses an electroplated nickel tensile layer and tension-controlled handle layer to propagate a crack across a wafer while controlling film thickness and reducing the surface roughness of the exfoliated devices as compared with previously reported exfoliation methods. Using this exfoliation tool, thin-film silicon samples are produced with a typical average surface roughness of 75 nm and a thickness that can be set anywhere between 5 μm and 35 μm by changing the exfoliation parameters.

Characterization of High-Performance Polycrystalline Silicon Complementary Metal–Oxide–Semiconductor Circuits

2007 ◽  
Vol 46 (1) ◽  
pp. 51-55 ◽  
Author(s):  
Genshiro Kawachi ◽  
Yoshiaki Nakazaki ◽  
Hiroyuki Ogawa ◽  
Masayuki Jyumonji ◽  
Noritaka Akita ◽  
...  
Keyword(s):  
Metal Oxide ◽  
Polycrystalline Silicon ◽  
High Performance ◽  
Complementary Metal Oxide Semiconductor ◽  
Metal Oxide Semiconductor ◽  
Oxide Semiconductor ◽  
Semiconductor Circuits

The Effect of Strain on the Formation of Dislocations at the SiGe/Si Interface

MRS Bulletin ◽  
1996 ◽  
Vol 21 (4) ◽  
pp. 38-44 ◽  
Author(s):  
F.K. LeGoues
Keyword(s):  
Metal Oxide ◽  
High Speed ◽  
High Performance ◽  
Field Effect Transistors ◽  
Low Cost ◽  
Complementary Metal Oxide Semiconductor ◽  
Metal Oxide Semiconductor ◽  
Oxide Semiconductor ◽  
Design Rule ◽  
Strained Si

Recently much interest has been devoted to Si-based heteroepitaxy, and in particular, to the SiGe/Si system. This is mostly for economical reasons: Si-based technology is much more advanced, is widely available, and is cheaper than GaAs-based technology. SiGe opens the door to the exciting (and lucrative) area of Si-based high-performance devices, although optical applications are still limited to GaAs-based technology. Strained SiGe layers form the base of heterojunction bipolar transistors (HBTs), which are currently used in commercial high-speed analogue applications. They promise to be low-cost compared to their GaAs counterparts and give comparable performance in the 2-20-GHz regime. More recently we have started to investigate the use of relaxed SiGe layers, which opens the door to a wider range of application and to the use of SiGe in complementary metal oxide semiconductor (CMOS) devices, which comprise strained Si and SiGe layers. Some recent successes include record-breaking low-temperature electron mobility in modulation-doped layers where the mobility was found to be up to 50 times better than standard Si-based metal-oxide-semiconductor field-effect transistors (MOSFETs). Even more recently, SiGe-basedp-type MOSFETS were built with oscillation frequency of up to 50 GHz, which is a new record, in anyp-type material for the same design rule.

Analysis and Simulation of a Low-Leakage Analog Single Gate and FinFET Circuits

2014 ◽  
Vol 13 (02) ◽  
pp. 1450012 ◽  
Author(s):  
Manorama Chauhan ◽  
Ravindra Singh Kushwah ◽  
Pavan Shrivastava ◽  
Shyam Akashe
Keyword(s):  
Integrated Circuits ◽  
Metal Oxide ◽  
Low Power ◽  
High Performance ◽  
Complementary Metal Oxide Semiconductor ◽  
Metal Oxide Semiconductor ◽  
Oxide Semiconductor ◽  
Short Channel ◽  
State Dependency ◽  
Low Leakage

In the world of Integrated Circuits, complementary metal–oxide–semiconductor (CMOS) has lost its ability during scaling beyond 50 nm. Scaling causes severe short channel effects (SCEs) which are difficult to suppress. FinFET devices undertake to replace usual Metal Oxide Semiconductor Field Effect Transistor (MOSFETs) because of their better ability in controlling leakage and diminishing SCEs while delivering a strong drive current. In this paper, we present a relative examination of FinFET with the double gate MOSFET (DGMOSFET) and conventional bulk Si single gate MOSFET (SGMOSFET) by using Cadence Virtuoso simulation tool. Physics-based numerical two-dimensional simulation results for FinFET device, circuit power is presented, and classifying that FinFET technology is an ideal applicant for low power applications. Exclusive FinFET device features resulting from gate–gate coupling are conversed and efficiently exploited for optimal low leakage device design. Design trade-off for FinFET power and performance are suggested for low power and high performance applications. Whole power consumptions of static and dynamic circuits and latches for FinFET device, believing state dependency, show that leakage currents for FinFET circuits are reduced by a factor of over ~ 10X, compared to DGMOSFET and ~ 20X compared with SGMOSFET.

Electromechanical Computing at 500°C with Silicon Carbide

Science ◽  
2010 ◽  
Vol 329 (5997) ◽  
pp. 1316-1318 ◽  
Author(s):  
Te-Hao Lee ◽  
Swarup Bhunia ◽  
Mehran Mehregany
Keyword(s):  
Silicon Carbide ◽  
Thermal Management ◽  
High Performance ◽  
Field Effect Transistors ◽  
Complementary Metal Oxide Semiconductor ◽  
Logic Circuits ◽  
Metal Oxide Semiconductor ◽  
Oxide Semiconductor ◽  
Propulsion Systems ◽  
Heat Sinking

Logic circuits capable of operating at high temperatures can alleviate expensive heat-sinking and thermal-management requirements of modern electronics and are enabling for advanced propulsion systems. Replacing existing complementary metal-oxide semiconductor field-effect transistors with silicon carbide (SiC) nanoelectromechanical system (NEMS) switches is a promising approach for low-power, high-performance logic operation at temperatures higher than 300°C, beyond the capability of conventional silicon technology. These switches are capable of achieving virtually zero off-state current, microwave operating frequencies, radiation hardness, and nanoscale dimensions. Here, we report a microfabricated electromechanical inverter with SiC complementary NEMS switches capable of operating at 500°C with ultralow leakage current.

High-Performance Thin-Film Transistors Enable By Metal Oxide Semiconductor with Polyaniline Doing in the Channel Layer

2020 ◽  
Vol MA2020-02 (28) ◽  
pp. 1955-1955
Author(s):  
Eun Goo Lee ◽  
Jaehak Lee ◽  
Sung-Eun Lee ◽  
Hyun-Jae Na ◽  
Kyungho Kim ◽  
...  
Keyword(s):  
Thin Film ◽  
Metal Oxide ◽  
Thin Film Transistors ◽  
High Performance ◽  
Metal Oxide Semiconductor ◽  
Oxide Semiconductor ◽  
Channel Layer
Sign in / Sign up

Export Citation Format

Share Document