Life Cycle Prediction and Evaluation of Clutch Friction Plate Considering Wear Models and Thermal Stress

2020 ◽  
Vol 143 (4) ◽  
Author(s):  
Mengyu Zhu ◽  
Xintian Liu ◽  
Fuchao Kan ◽  
Ziyun You
Keyword(s):  
Life Cycle ◽  
Friction Surface ◽  
Sliding Friction ◽  
Contact Model ◽  
Effect Of Temperature ◽  
Body Model ◽  
Full Life Cycle ◽  
Influence Of Temperature On ◽  
Friction Plate ◽  
Work Model

Abstract To predict the life of the clutch friction plate, friction characteristics of the friction plate and the steel sheet assembly are analyzed in the full life cycle. A contact model of the friction surface is built based on the micro-convex body model. Wear mathematical models of friction plate are established respectively based on the contact model and sliding friction work model. The wear results of the two models are compared and analyzed. The effect of temperature on wear is considered. Fatigue life of the friction plate is predicted by wear mathematical model according to the real working states. The accuracy of the contact model and the influence of temperature on the wear are determined through the comparative analysis of each prediction result.

Study on the transient temperature distribution of new conical friction plate under sliding friction

2021 ◽  
pp. 095440702110696
Author(s):  
Yanzhong Wang ◽  
Peng Liu
Keyword(s):  
Temperature Distribution ◽  
Temperature Gradient ◽  
Temperature Rise ◽  
Friction Surface ◽  
Sliding Friction ◽  
Conical Surface ◽  
Transient Temperature ◽  
Radial Temperature Gradient ◽  
Radial Temperature ◽  
Friction Plate

Conical friction surface is a novel configuration for friction plate in transmission. Numerical FEA models for transient heat transfer and distribution of conically grooved friction plate have been established to investigate the thermal behavior of the conical surface with different configurations. The finite element method is used to obtain the numerical solution, the temperature test data of conical surface are obtained by the friction test rig. In order to study and compare the temperature behavior of conically grooved friction plate, several three-dimensional transient temperature models are established. The heat generated on the friction interface during the continuous sliding process is calculated. Two different pressure conditions were defined to evaluate the influence of different load conditions on temperature rise and the effects of conical configuration parameters on surface temperature distribution are investigated. The results show that the radial temperature gradient on conical friction surface is obvious. The uniform pressure condition could be used when evaluating the temperature rise of conically grooved friction plate. The increase of the cone height could improve the radial temperature gradient of the conically grooved friction plate.

scholarly journals Catostylus tagi (Class: Scyphozoa, Order: Discomedusae, Suborder: Rhizostomida, Family: Catostylidae) life cycle and first insight into its ecology

PeerJ ◽  
2021 ◽  
Vol 9 ◽  
pp. e12056
Author(s):  
Sonia K.M. Gueroun ◽  
Tatiana M. Torres ◽  
Antonina Dos Santos ◽  
Nuno Vasco-Rodrigues ◽  
João Canning-Clode ◽  
...  
Keyword(s):  
Life Cycle ◽  
Developmental Stages ◽  
Anthropogenic Activities ◽  
Total Body Length ◽  
Effect Of Temperature ◽  
Ecosystem Structure ◽  
Full Life Cycle ◽  
Wide Range ◽  
Key Factor ◽  
Total Body

Jellyfish proliferations, which are conspicuous and natural events, cause blooms that may lead to severe consequences for anthropogenic activities and ecosystem structure and functioning. Although research during the last decade has focused on factors influencing the different jellyfish life stages, few species currently have their full life cycle known. In this context, we describe for the first time the developmental stages in the life cycle of Catostylus tagi, from planula to young medusa, reared in the laboratory. The species displays the typical Rhizostomida metagenetic life cycle. Mature scyphistomae display 16 tentacles and a total body length of 1.5 ± 0.2 mm. Only podocyst production and strobilation were observed. Strobilation, occurring continuously under laboratory conditions, was mainly polydisc. The eight-rayed typical ephyrae, with a total body diameter of 2.4 ± 0.4 mm at detachment, showed development typical of the Rhizostomida. As a first step in studying this species’ ecology, we also present preliminary assessments of: (i) the influence of different temperature and salinity regimes on planulae survival, settlement and metamorphosis and (ii) the effect of temperature and diet on asexual reproduction. The results showed a high tolerance of planulae to a wide range of salinities (15‰ to 25‰), while polyp development was significantly faster at higher temperature (20–25 °C). Strobilation onset was 2–3 times faster at 20 °C (10.6 ± 5.4 to 15 ± 6.6 day at various tested diet) than at 15 °C (32.2 ± 3 day). Feeding was a key factor as unfed polyps never underwent strobilation during the trial. Finally, we present the spatial and seasonal distribution of C. tagi in the Tagus estuary (Portugal) in 2019, showing its occurrence throughout the year (except in April), with most observations recorded on the northern shoreline. As C. tagi shows the ability to form blooms and a wide tolerance for temperature and salinity (for planulae and medusae stage), it is essential to understand its life cycle.

The effect of temperature on high-resolution TEM image contrast

1995 ◽  
Vol 53 ◽  
pp. 640-641
Author(s):  
T. Geipel ◽  
W. Mader ◽  
P. Pirouz
Keyword(s):  
Form Factor ◽  
Inelastic Scattering ◽  
Accurate Method ◽  
Waller Factor ◽  
Effect Of Temperature ◽  
Specimen Thickness ◽  
Influence Of Temperature ◽  
Debye Waller Factor ◽  
Influence Of Temperature On ◽  
Atomic Form Factor

Temperature affects both elastic and inelastic scattering of electrons in a crystal. The Debye-Waller factor, B, describes the influence of temperature on the elastic scattering of electrons, whereas the imaginary part of the (complex) atomic form factor, fc = fr + ifi, describes the influence of temperature on the inelastic scattering of electrons (i.e. absorption). In HRTEM simulations, two possible ways to include absorption are: (i) an approximate method in which absorption is described by a phenomenological constant, μ, i.e. fi; - μfr, with the real part of the atomic form factor, fr, obtained from Hartree-Fock calculations, (ii) a more accurate method in which the absorptive components, fi of the atomic form factor are explicitly calculated. In this contribution, the inclusion of both the Debye-Waller factor and absorption on HRTEM images of a (Oll)-oriented GaAs crystal are presented (using the EMS software.Fig. 1 shows the the amplitudes and phases of the dominant 111 beams as a function of the specimen thickness, t, for the cases when μ = 0 (i.e. no absorption, solid line) and μ = 0.1 (with absorption, dashed line).

scholarly journals Full life-cycle monitoring and earlier warning for bolt joint loosening using modified vibro-acoustic modulation

2022 ◽  
Vol 162 ◽  
pp. 108054
Author(s):  
Xiaoshu Qin ◽  
Chang Peng ◽  
Gaozheng Zhao ◽  
Zengye Ju ◽  
Shanshan Lv ◽  
...  
Keyword(s):  
Life Cycle ◽  
Full Life Cycle ◽  
Full Life ◽  
Acoustic Modulation ◽  
Cycle Monitoring

Research on dynamic characteristics of gear system considering the influence of temperature on material performance

2021 ◽  
pp. 107754632110026
Author(s):  
Zhou Sun ◽  
Siyu Chen ◽  
Xuan Tao ◽  
Zehua Hu
Keyword(s):  
Elastic Modulus ◽  
Dynamic Characteristics ◽  
Poisson’S Ratio ◽  
Gear System ◽  
Poisson's Ratio ◽  
Effect Of Temperature ◽  
Time Varying ◽  
Influence Of Temperature ◽  
Meshing Stiffness ◽  
Influence Of Temperature On

Under high-speed and heavy-load conditions, the influence of temperature on the gear system is extremely important. Basically, the current work on the effect of temperature mostly considers the flash temperature or the overall temperature field to cause expansion at the meshing point and then affects nonlinear factors such as time-varying meshing stiffness, which lead to the deterioration of the dynamic transmission. This work considers the effect of temperature on the material’s elastic modulus and Poisson’s ratio and relates the temperature to the time-varying meshing stiffness. The effects of temperature on the elastic modulus and Poisson’s ratio are expressed as functions and brought into the improved energy method stiffness calculation formula. Then, the dynamic characteristics of the gear system are analyzed. With the bifurcation diagram, phase, Poincaré, and fast Fourier transform plots of the gear system, the influence of temperature on the nonlinear dynamics of the gear system is discussed. The numerical analysis results show that as the temperature increases, the dynamic response of the system in the middle-speed region gradually changes from periodic motion to chaos.

Flow Behaviors of High Acyl Gellan Aqueous Solutions as Affected by Temperature, and Calcium and Gellan Concentrations

2008 ◽  
Vol 4 (5) ◽  
Author(s):  
Yiqun Huang ◽  
Pawan Singh Takhar ◽  
Juming Tang ◽  
Barry G Swanson
Keyword(s):  
Shear Rate ◽  
Aqueous Solutions ◽  
Apparent Viscosity ◽  
Flow Resistance ◽  
Effect Of Temperature ◽  
Temperature Changes ◽  
Influence Of Temperature ◽  
Rheological Behaviors ◽  
Low Concentrations ◽  
Influence Of Temperature On

Rheological behaviors of high acyl (HA) gellan are not well understood partially because of its relatively late commercialization compared to low acyl gellan. The objective of this study was to investigate the effect of temperature (5-30 °C), calcium (0, 1 and 10 mM) and gellan concentrations (0.0044-0.1000% w/v) on the flow behaviors of high acyl gellan aqueous solutions using rheological tests. Gellan solutions with 0 or 1 mM added Ca++ exhibited shear thinning behavior at gellan concentrations above 0.0125%. The influence of temperature on apparent viscosity (shear rate, 100 s-1) of gellan solutions can be described with an Arrhenius relationship. The apparent viscosity of gellan solution at low concentrations was more sensitive to temperature changes. The addition of Ca++ led to a decrease in flow resistance for a dilute gellan solution (<0.0125%), but an increased resistance for a relatively concentrated gellan solution (>0.0125%).

Sign in / Sign up

Export Citation Format

Share Document