Investigation of a novel solar powered trigeneration system for simultaneous production of electricity, heating, and refrigeration below freezing

2021 ◽  
pp. 1-43
Author(s):  
Eydhah Almatrafi ◽  
Abdul Khaliq
Keyword(s):  
Inlet Temperature ◽  
Outlet Temperature ◽  
Basic Solution ◽  
Ansys Fluent ◽  
Kalina Cycle ◽  
Ammonia Water ◽  
Entry Pressure ◽  
Coil Diameter ◽  
Energy And Exergy ◽  
Solar Powered

Abstract A solar powered trigeneration system consisting of tower solar collector, Kalina cycle with the heat exchanger, and EARC is proposed to produce refrigeration below freezing, electricity, and process heat, simultaneously. Simulation through CFD using ANSYS-FLUENT package is conducted to examine the effect of coil diameter and inlet oil temperature on the pressure and temperature of SHTF. It is found that, for inlet temperature of 92oC and DNI 850 W/m2, the SHTF outlet temperature increases by 9% when the coil diameter increased from 150 to 400 mm. Trigeneration performance is analyzed after altering; hot oil outlet temperature, turbine entry pressure, and the concentration of ammonia-water basic solution to study their effect on power produced by turbine, refrigeration load, exergy of refrigeration, and efficiencies of trigeneration system. Increase in concentration of ammonia-water basic solution is leading towards the significant increase in the turbine power and the elevation of trigeneration system’s energy and exergy efficiencies. Bottoming of Kalina cycle with EARC shows the distribution of solar energy as; energetic output 72.31% and energy lost to environment 27.69%. The solar exergy supplied to the trigeneration system is distributed as; 16.23% exergy is produced, 1.62% is the exergy loss, and 82.15% is the exergy destroyed.

scholarly journals Numerical Study of a Helical Heat Exchanger for Wort Cooling in the Artisanal Beer Production Process

2020 ◽  
Vol 29 (54) ◽  
pp. e11632
Author(s):  
Fernando Toapanta-Ramos ◽  
Luis González-Rojas ◽  
Elmo Calero ◽  
Bryan Calderón ◽  
William Quitiaquez
Keyword(s):  
Heat Exchanger ◽  
Cold Water ◽  
Numerical Study ◽  
Computational Techniques ◽  
Inlet Temperature ◽  
Outlet Temperature ◽  
Ansys Fluent ◽  
Craft Beer ◽  
Helical Heat Exchanger ◽  
Beer Production

The objective of the present work is to study the behavior of a helical tube and shell heat exchanger, for the cooling of the wort in the process of making craft beer with cold water, through the methodology of computational fluid dynamics (CFD) by finite volume models for heat exchanger modeling. This by using the ANSYS Fluent software, which allows to understand the behavior of the fluid through equations that describe their movement and behavior, using numerical methods and computational techniques. In the mesh convergence, two methods were used, orthogonality and obliquity, with which it was confirmed that the meshing is ideal in the simulations that were carried out. For the simulation, the k-epsilon turbulence model and the energy model were used. Through various simulations, it was obtained that by varying the mass flow, better results are reducing the outlet temperature, with a variation of 15.16 °C, while varying the inlet temperature of the water, there is just a variation from 2.71 °C to 0.01 °C. Therefore, a significant improvement in the performance of the heat exchanger was found. In the same way, it was confirmed that the number of spikes in the heat exchanger is adequate, since the outlet temperature would not be reached with less spikes.

Performance Prediction of a Multi-Stage Ammonia-Water Turbine Under Variable Nozzle Operation via Machine Learning

2021 ◽  
Author(s):  
Yang Du ◽  
Tingting Liu ◽  
Yiping Dai ◽  
Gang Fan ◽  
Jiangfeng Wang ◽  
...  
Keyword(s):  
Machine Learning ◽  
Inlet Temperature ◽  
Outlet Temperature ◽  
Nozzle Outlet ◽  
Turbine Inlet Temperature ◽  
Ammonia Water ◽  
Turbine Efficiency ◽  
Radial Turbine ◽  
Turbine Inlet ◽  
Multi Stage

Abstract This study proposes machine learning models to predict the performance of a multi-stage ammonia-water radial turbine using variable nozzle operation under different operating conditions. A 1.2 MW four-stage ammonia-water radial turbine is firstly designed. Then, the one-dimensional off-design simulation model is developed based on the geometric parameters to mainly evaluate the effects of different nozzle outlet angles and turbine inlet temperatures on the turbine performance. A set of data, which consists of 10,000 training points based on one-dimensional model, is used to train the proposed two high-dimensional model representation (HDMR) methods. The forward HDMR model predicts the mass flow rate, turbine outlet temperature, turbine power and turbine efficiency for any combination of turbine nozzle outlet angle and turbine inlet temperature, while the reverse HDMR model predicts the mass flow rate, turbine outlet temperature, turbine efficiency and turbine nozzle outlet angle for any combination of turbine power and turbine inlet temperature. The two HDMR models are validated using 238 sets of separated test data. The results show that the minimum coefficients of determination (R2) of forward HDMR model and reverse HDMR model are 0.9837 and 0.9953, respectively. The maximum relative errors of two HDMR models are below 1.6822%, so the quality of the proposed machine learning methods is high. The overall performance maps of multi-stage ammonia-water radial turbine under the variable nozzle operation method are constructed based on the reverse HDMR model. The reverse HDMR model is helpful in monitoring the healthy operation state of turbine.

scholarly journals Energy and Exergy Efficiency Analysis of Fluid Flow and Heat Transfer in Sinter Vertical Cooler

Energies ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4522
Author(s):  
Zude Cheng ◽  
Haitao Wang ◽  
Junsheng Feng ◽  
Yongfang Xia ◽  
Hui Dong
Keyword(s):  
Heat Transfer ◽  
Energy Efficiency ◽  
Fluid Flow ◽  
Waste Heat ◽  
Exergy Efficiency ◽  
Inlet Temperature ◽  
Operational Parameters ◽  
Flow And Heat Transfer ◽  
Maximum Value ◽  
Energy And Exergy

In order to fully understand the energy and exergy transfer processes in sinter vertical coolers, a simulation model of the fluid flow and heat transfer in a vertical cooler was established, and energy and exergy efficiency analyses of the gas–solid heat transfer in a vertical cooler were conducted in detail. Based on the calculation method of the whole working condition, the suitable operational parameters of the vertical cooler were obtained by setting the net exergy efficiency in the vertical cooler as the indicator function. The results show that both the quantity of sinter waste heat recovery (SWHR) and energy efficiency increased as the air flow rate (AFR) increased, and they decreased as the air inlet temperature (AIT) increased. The increase in the sinter inlet temperature (SIT) resulted in an increase in the quantity of SWHR and a decrease in energy efficiency. The air net exergy had the maximum value as the AFR increased, and it only increased monotonically as the SIT and AIT increased. The net exergy efficiency reached the maximum value as the AFR and AIT increased, and the increase in the SIT only resulted in a decrease in the net exergy efficiency. When the sinter annual production of a 360 m2 sintering machine was taken as the processing capacity of the vertical cooler, the suitable operational parameters of the vertical cooler were 190 kg/s for the AFR, and 353 K for the AIT.

Heat Transfer to Supercritical Water in Vertical Annular Channel and 3-Rod Bundle

2009 ◽  
Author(s):  
V. G. Razumovskiy ◽  
Eu. N. Pis’mennyy ◽  
A. Eu. Koloskov ◽  
I. L. Pioro
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Supercritical Water ◽  
Annular Channel ◽  
Heat Fluxes ◽  
Inlet Temperature ◽  
Outlet Temperature ◽  
Rod Bundle ◽  
Temperature Regimes ◽  
Outside Diameter

The results of heat transfer to supercritical water flowing upward in a vertical annular channel (1-rod channel) and tight 3-rod bundle consisting of the tubes of 5.2-mm outside diameter and 485-mm heated length are presented. The heat-transfer data were obtained at pressures of 22.5, 24.5, and 27.5 MPa, mass flux within the range from 800 to 3000 kg/m2·s, inlet temperature from 125 to 352°C, outlet temperature up to 372°C and heat flux up to 4.6 MW/m2 (heat flux rate up to 2.5 kJ/kg). Temperature regimes of the annular channel and 3-rod bundle were stable and easily reproducible within the whole range of the mass and heat fluxes, even when a deteriorated heat transfer took place. The data resulted from the study could be applicable for a reference estimation of heat transfer in future designs of fuel bundles.

Experimental Study to Characterize the Performance of Combined Photovoltaic/Thermal Air Collectors

2012 ◽  
Vol 134 (3) ◽  
Author(s):  
Véronique Delisle ◽  
Michaël Kummert
Keyword(s):  
Thermal Efficiency ◽  
Closed Loop ◽  
Multiple Linear Regression Model ◽  
Open Loop ◽  
Electrical Performance ◽  
Back Surface ◽  
Inlet Temperature ◽  
Outlet Temperature ◽  
Cell Temperature ◽  
Average Temperature

Combined photovoltaic/thermal (PV/T) collectors show great potential for reaching the objective of net-zero energy consumption in buildings, but the number of products on the market is still very limited. One of the reasons for the slow market uptake of PV/T collectors is the absence of standardized methods to characterize their performance. Performance characterization is a challenge for PV/T collectors because of the interaction between the thermal and electrical yield. This study addresses this particular issue for PV/T air collectors used in either closed-loop or open-loop configurations. In particular, it presents the potential of the equivalent cell temperature method to determine the temperature of the PV cells in a PV/T air collector and validates models to predict the thermal performance and cell temperature for this particular type of solar collector. Indoor and outdoor experimental tests were performed on two c-Si unglazed PV/T modules. The indoor part of this procedure provided the thermal diode voltage factor and the open-circuit voltage temperature coefficient, two parameters that are essential in the calculation of the equivalent cell temperature. The outdoor procedure consisted of acquiring simultaneous electrical and thermal measurements at various inlet temperatures and flowrates. For the collector used in a closed-loop configuration, thermal efficiency models using the fluid inlet, outlet, or average temperature in the calculation of the reduced temperature provided similar results. For an open-loop configuration, a thermal efficiency model as a function of the fluid outlet flowrate was found to be more appropriate. Using selection of variable methods, it was found that a multiple linear regression model using the fluid inlet temperature, the irradiance, and the fluid outlet temperature as predictive variables could be used to estimate both the PV module back surface average temperature and the equivalent cell temperature. When using the PV temperature predicted by these models in the electrical efficiency model, both PV temperatures showed similar performance. In collectors where the PV back surface temperature is not accessible for temperature sensors mounting, the equivalent cell temperature provides a valuable alternative to be used as the PV temperature. The PV/T collector thermal and electrical performance in either closed-loop or open-loop configurations was found to be encapsulated with a series of five-plots.

Energy and exergy analysis of a downstream single-row air washer at different droplet diameters for air cooling application

2022 ◽  
pp. 095440622110645
Author(s):  
Minhua Huang ◽  
Haiqiao Wang ◽  
Feng Tian ◽  
Junxin Huang ◽  
Shiqiang Chen ◽  
...  
Keyword(s):  
Performance Indicator ◽  
Droplet Diameter ◽  
Exergy Efficiency ◽  
Air Cooling ◽  
Design Calculation ◽  
Outlet Temperature ◽  
Single Row ◽  
Energy And Exergy ◽  
Water Gas ◽  
Gas Ratio

This study proposes a downstream single-row air washer for air cooling. The theoretical energy and exergy balance models were established at different droplet diameters and verified by the experimental data. Based on the abovementioned theoretical relationship, the single performance indicator of heat exchange efficiency (HEE) and exergy efficiency was quantitatively analyzed; a comprehensive analysis method of two indicators was proposed, combining HEE and exergy efficiency, and a numerical simulation was carried out. Results show that the smaller the droplet diameter and the larger the water–air ratio, the lower the dry-bulb temperature of the outlet air and the higher the HEE and exergy flux destruction. When the droplet diameter is less than 440 μm, the droplet diameter does not affect exergy efficiency and dry-bulb temperature. When the droplet diameter is larger than 440 μm, the droplet diameter is positively correlated with the air outlet dry-bulb temperature and exergy efficiency; in contrast, the water–gas ratio is negatively correlated with the air outlet dry-bulb temperature. An engineering case reveals that when the air outlet temperature is less than 34°C, the critical water–gas ratio can be set as 2.6 (mass ratio). At this time, the HEE is more than 90%, the exergy efficiency is more than 60%, and the critical value of droplet diameter is 440 μm. The research results provide an essential theoretical basis for the optimization of engineering design calculation.

The antioxidative-activity stability of aloe vera (Aloe vera var. chinensis) instant during storage

Food Research ◽  
2021 ◽  
Vol 5 (4) ◽  
pp. 288-293
Author(s):  
Riyanto ◽  
Ch. Wariyah
Keyword(s):  
Lipid Peroxidation ◽  
Critical Condition ◽  
Antioxidative Activity ◽  
Radical Scavenging ◽  
Aloe Vera ◽  
Oxygen Absorption ◽  
Inlet Temperature ◽  
Outlet Temperature ◽  
Plastic Film ◽  
Lipid Peroxidation Inhibition

Aloe vera contains a phenolic compound that has bioactive activity. Previous research showed that microencapsulation of aloe vera powder with maltodextrin as an encapsulation agent produced instant aloe vera with high antioxidative activity. The problem was the hygroscopic instant caused rapid moisture and oxygen absorption during storage, therefore decreasing the instant aloe vera antioxidative activity periodically. The aim of this research was to evaluate the antioxidative activity stability of instant aloe vera during storage. The processing of instant aloe vera through a reconstituted aloe vera powder with water with a ratio of 1:120 and then added with 2.5% maltodextrin as the encapsulating agent. The solution was then inserted into a spray dryer with an inlet temperature of 130oC, an outlet temperature of 103oC, and the flow rate of the solution is 350.0 mL/h. The resulted instant aloe vera was divided into 15 packs with a weight of 25 g, and each sample was wrapped with polyethylene plastic film with 0.80 mm thickness and then was stored at 25oC with a relative humidity of 75%. The sample was conducted in triplicate. The moisture content, and antioxidative activity that was based on the ability to capture 1,1-diphenyl-2- picrylhydrazyl (DPPH) radical (RSA) and lipid peroxidation inhibition were analyzed every week until the critical condition was achieved at a moisture level of 12%. The research showed that the radical scavenging activity (RSA) and lipid peroxidation inhibition of instant aloe vera before storage were 16.34±1.22% and 39.33±1.68%, respectively, whereas in the critical condition the RSA was 3.63±0.04% and the lipid peroxidation inhibition was 22.31±0.02%. Based on their antioxidative activity, the appropriate storage time of instant aloe vera was about 12 weeks in polyethylene plastic film of 0.08 mm thickness

Thermal Aspects of Using Uranium Mononitride Fuel in a SuperCritical Water-Cooled Reactor at Maximum Heat Flux Conditions

2010 ◽  
Author(s):  
Ashley Milner ◽  
Caleb Pascoe ◽  
Hemal Patel ◽  
Wargha Peiman ◽  
Graham Richards ◽  
...  
Keyword(s):  
Heat Flux ◽  
Supercritical Water ◽  
Thermal Efficiency ◽  
Inlet Temperature ◽  
Outlet Temperature ◽  
Maximum Heat ◽  
Light Water ◽  
Maximum Heat Flux ◽  
Centerline Temperature ◽  
Uranium Mononitride

Generation IV nuclear reactor technology is increasing in popularity worldwide. One of the six Generation-IV-reactor types are SuperCritical Water-cooled Reactors (SCWRs). The main objective of SCWRs is to increase substantially thermal efficiency of Nuclear Power Plants (NPPs) and thus, to reduce electricity costs. This reactor type is developed from concepts of both Light Water Reactors (LWRs) and supercritical fossil-fired steam generators. The SCWR is similar to a LWR, but operates at a higher pressure and temperature. The coolant used in a SCWR is light water, which has supercritical pressures and temperatures during operation. Typical light water operating parameters for SCWRs are a pressure of 25 MPa, an inlet temperature of 280–350°C, and an outlet temperature up to 625°C. Currently, NPPs have thermal efficiency about of 30–35%, whereas SCW NPPs will operate with thermal efficiencies of 45–50%. Furthermore, since SCWRs have significantly higher water parameters than current water-cooled reactors, they are able to support co-generation of hydrogen. Studies conducted on fuel-channel options for SCWRs have shown that using uranium dioxide (UO2) as a fuel at supercritical-water conditions might be questionable. The industry accepted limit for the fuel centerline temperature is 1850°C and using UO2 would exceed this limit at certain conditions. Because of this problem, there have been other fuel options considered with a higher thermal conductivity. A generic 43-element bundle for an SCWR, using uranium mononitride (UN) as the fuel, is discussed in this paper. The material for the sheath is Inconel-600, because it has a high resistance to corrosion and can adhere to the maximum sheath-temperature design limit of 850°C. For the purpose of this paper, the bundle will be analyzed at its maximum heat flux. This will verify if the fuel centerline temperature does not exceed 1850°C and that the sheath temperature remains below the limit of 850°C.

Sign in / Sign up

Export Citation Format

Share Document