Coal Fueled Aero-Derivative Gas Turbine: Design Approach

1988 ◽  
Author(s):  
M. W. Horner ◽  
P. E. Sabla ◽  
S. G. Kimura
Keyword(s):  
Gas Turbine ◽  
High Efficiency ◽  
Development Program ◽  
Small Scale ◽  
Water Mixture ◽  
Coal Fuel ◽  
Cost Of Energy ◽  
Annular Combustor ◽  
Environmentally Sound ◽  
Turbine Design

The direct use of coal as a gas turbine fuel offers the opportunity to burn coal in an environmentally sound manner at a competitive cost of energy. A development program is underway to verify the feasibility of using coal water mixture to fuel an aero-derivative gas turbine. This paper presents the overall program approach, required gas turbine design modifications, and reports the results from small-scale combustor test facilities. The GE LM500 gas turbine was selected for this program because of its high efficiency and size, which is appropriate for transportation and cogeneration markets. The LM500 gas turbine power system design will be modified to accommodate coal fuel and any required emissions control devices. The design for the modified annular combustor is complete and preparations for coal fired tests of a 140 degree annular sector combustor are in progress. The combustor design and test development are being supported by a component test program with a One Nozzle Segment Combustor and a single can combustor LM500 Turbine Simulator. These test facilities are providing results on coal water mixture handling and fuel nozzle design, air staging requirements, component metal temperatures, combustor temperature performance, ash deposition rates, and emissions abatement for NOx, SOx, and particulates.

Development of a Water-Cooled Gas Turbine

1978 ◽  
Author(s):  
M. W. Horner ◽  
W. H. Day ◽  
D. P. Smith ◽  
A. Cohn
Keyword(s):  
Gas Turbine ◽  
Technology Development ◽  
Pressure Ratio ◽  
Development Program ◽  
Combined Cycle ◽  
Small Scale ◽  
Performance Curves ◽  
Basic Technology ◽  
Gas Fuel ◽  
Turbine Design

Development of water-cooled gas turbine technology was begun at General Electric in the early 1960’s, and by the early 1970’s, a small-scale turbine had been operated to temperatures of 2850 F and 16 atm, with metal temperature less than 1000 F. The Water-Cooled Turbine Development Program was begun in 1974, funded by the Electric Power Research Institute, to do preliminary design on a utility-size gas turbine using water cooling and to do basic technology development to address the problem areas. This paper presents the results of the program, including descriptions of the test hardware and data on phenomena, such as corrosion, erosion, heat transfer, and water collection. Cycle analysis results are presented for two potential combined cycle configurations: (a) one using low-Btu coal gas fuel, and (b) one using a heavy liquid fuel. Summary performance curves are given showing the effect of changes of pressure ratio and firing temperature. Methods of improving the baseline cycle and their effect on baseline performance which are judged most promising are also given on the performance curves. Turbine design features to achieve low component metal surface temperatures for increased fuels flexibility are given with particular emphasis to the first-stage nozzles and buckets. Fundamental development testing needs have been identified and programs have been put into place to bring the water-cooled turbine to a point where a full-size water-cooled turbine can be built. Descriptions of the development test facilities, task descriptions, test plans and /or test results are given for eight tasks.

Three Spool High Efficiency Small Scale Gas Turbine Concept

2017 ◽  
Author(s):  
Matti Malkamäki ◽  
Ahti Jaatinen-Värri ◽  
Antti Uusitalo ◽  
Aki Grönman ◽  
Juha Honkatukia ◽  
...  
Keyword(s):  
Power Generation ◽  
Gas Turbine ◽  
Gas Turbines ◽  
High Efficiency ◽  
Small Scale ◽  
Inlet Temperature ◽  
Substantial Impact ◽  
Electrical Efficiency ◽  
Partial Load ◽  
Reciprocating Engines

Decentralized electricity and heat production is a rising trend in small-scale industry. There is a tendency towards more distributed power generation. The decentralized power generation is also pushed forward by the policymakers. Reciprocating engines and gas turbines have an essential role in the global decentralized energy markets and improvements in their electrical efficiency have a substantial impact from the environmental and economic viewpoints. This paper introduces an intercooled and recuperated three stage, three-shaft gas turbine concept in 850 kW electric output range. The gas turbine is optimized for a realistic combination of the turbomachinery efficiencies, the turbine inlet temperature, the compressor specific speeds, the recuperation rate and the pressure ratio. The new gas turbine design is a natural development of the earlier two-spool gas turbine construction and it competes with the efficiencies achieved both with similar size reciprocating engines and large industrial gas turbines used in heat and power generation all over the world and manufactured in large production series. This paper presents a small-scale gas turbine process, which has a simulated electrical efficiency of 48% as well as thermal efficiency of 51% and can compete with reciprocating engines in terms of electrical efficiency at nominal and partial load conditions.

scholarly journals Study on the Turbine Vane and Blade for a 1500°C Class Industrial Gas Turbine

1993 ◽  
Author(s):  
S. Amagasa ◽  
K. Shimomura ◽  
M. Kadowaki ◽  
K. Takeishi ◽  
H. Kawai ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
High Efficiency ◽  
Development Program ◽  
Test Results ◽  
Directionally Solidified ◽  
Barrier Coating ◽  
Turbine Vane ◽  
Nickel Base ◽  
Industrial Gas Turbine

This paper describes the summary of a three year development program for the 1st stage stationary vane and rotating blade for the next generation, 1500°C Class, high efficiency gas turbine. In such a high temperature gas turbine, the 1st turbine vane and blade are the most important hot parts. Full coverage film cooling (FCFC) is adopted for the cooling scheme, and directionally solidified (DS) nickel base super-alloy and thermal barrier coating (TBC) will be used to prolong the creep and thermal fatigue life. The concept of the cooling configuration, fundamental cascade test results and material test results will be presented.

scholarly journals 2MW Class High Efficiency Gas Turbine IM270 for Co-Generation Plants

1996 ◽  
Author(s):  
Hideo Kobayashi ◽  
Shogo Tsugumi ◽  
Yoshio Yonezawa ◽  
Riuzou Imamura
Keyword(s):  
Gas Turbine ◽  
High Efficiency ◽  
Mechanical Design ◽  
Development Program ◽  
Gas Turbine Engine ◽  
Maintenance Cost ◽  
Turbine Engine ◽  
Generation Plant ◽  
Emission Regulation ◽  
Heavy Duty Gas Turbine

IHI is developing a new heavy duty gas turbine engine for 2MW class co-generation plants, which is called IM270. This engine is a simple cycle and single-spool gas turbine engine. Target thermal efficiency is the higher level in the same class engines. A dry low NOx combustion system has been developed to clear the strictest emission regulation in Japan. All parts of the IM270 are designed with long life for low maintenance cost. It is planned that the IM270 will be applied to a dual fluid system, emergency generation plant, machine drive engine and so on, as shown in Fig.1. The development program of IM270 for the co-generation plant is progress. The first prototype engine test has been started. It has been confirmed that the mechanical design and the dry low NOx system are practical. The component tuning test is being executed. On the other hand, the component test is concurrently in progress. The first production engine is being manufactured to execute the endurance test using a co-generation plant at the IHI Kure factory. This paper provides the conceptual design and status of the IM270 basic engine development program.

Water-Cooled Gas Turbine Technology Development: Fuels Flexibility

1979 ◽  
Author(s):  
M. W. Horner ◽  
W. H. Day ◽  
D. P. Smith ◽  
A. Cohn
Keyword(s):  
Gas Turbine ◽  
Technology Development ◽  
Development Program ◽  
Open Circuit ◽  
Model Verification ◽  
Small Scale ◽  
Water Cooling ◽  
Gas Temperature ◽  
Pressurized Water ◽  
Early Results

A continuing technology development program initiated by General Electric (GE) in the early 1960s and joined by the Electric Power Research Institute (EPRI) in 1974 is successfully resolving potential barrier problems in the development of water cooled turbines. Early work by GE Corporate Research and Development demonstrated the feasibility of closed circuit, pressurized water-cooling of stationary nozzles (vanes), and of open circuit, unpressurized water-cooling of rotating buckets (blades). A small-scale turbine was designed, fabricated, and operated at a gas temperature of 2850 F (1565 C) at 16 atm, with surface metal temperatures less than 1000 F (540 C). Early results from the EPRI sponsored Water-Cooled Gas Turbine Development Programs were presented at the 1978 Gas Turbine Conference (Report #ASME 78-GT-72). This paper reports more recent results, obtained between mid-1977 and mid-1978. Significant progress has been made in a number of areas: (a) water-cooled nozzle and bucket design and fabrication, (b) corrosion kinetics model verification and testing, (c) partially filled internal channel bucket heat transfer testing, and (d) stationary to rotating water transfer and collection testing. Results to date are encouraging with regard to the application of water-cooled turbine components to achieve improved reliability and fuels flexibility at increased turbine firing temperatures.

Development of the PGT 25 High Efficiency Gas Turbine: Part 3 — Experimental Program and Testing

1984 ◽  
Author(s):  
P. Lacitignola ◽  
E. Valentini
Keyword(s):  
Gas Turbine ◽  
High Efficiency ◽  
Engine Performance ◽  
Experimental Methods ◽  
Experimental Program ◽  
Load Testing ◽  
Testing Program ◽  
Full Load ◽  
Engine Testing ◽  
Turbine Design

This paper presents a review of the engineering testing program related to development of the PGT-25 gas turbine. The experimental methods employed and their capability of providing information for the tuning of the engine and its parts are discussed. Testing has continuously supported turbine design and development; integration of analytical and experimental procedures has proven to be efficient for successful final engine testing. Full load testing, using well developed instrumentation, has made it possible to know actual component behavior and engine performance in steady and transient states, over the entire speed and power range. The reliability of the machine has been assessed through the results of these tests.

Conversion of the AE 1107C From the V-22 Osprey Application to Marine Service

2013 ◽  
Author(s):  
Zechariah D. Green ◽  
Sean Padfield ◽  
Andrew F. Barrett ◽  
Paul G. Jones
Keyword(s):  
Gas Turbine ◽  
System Integration ◽  
Development Program ◽  
Gas Turbine Engine ◽  
Naval Vessel ◽  
Turbine Engine ◽  
The Us ◽  
Technical Risk ◽  
Turbine Design ◽  
System Designs

This paper presents a study on the conversion of the Rolls-Royce AE 1107C V-22 Osprey gas turbine engine into the MT7 Ship-to-Shore Connector (SSC) marine gas turbine engine. The US Navy led SSC design requires a propulsion and lift gas turbine rated at 5,230 shaft horsepower, which the AE 1107C variant MT7 is capable of providing with margin on power and specific fuel consumption. The MT7 leverages the AE family of engines to provide a propulsion and lift engine solution for the SSC craft. Extensive testing and analysis completed during the AE 1107C development program aided in the robust gas turbine design required to meet the needs of the SSC program. Requirements not met by the AE 1107C configuration were achieved with designs based on the AE family of engines and marine grade sub-system designs. Despite the fact that system integration and testing remain as key activities for integrating the MT7 with the SSC craft, conversion of the AE 1107C FAA certified engine into an American Bureau of Shipping Naval Vessel Rules Type Approved MT7 engine provides a low technical risk alternative for the demanding requirements of the SSC application.

Summary of CGT302 Ceramic Gas Turbine Research and Development Program

2000 ◽  
Author(s):  
Isashi Takehara ◽  
Tetsuo Tatsumi ◽  
Yoshihiro Ichikawa
Keyword(s):  
Research And Development ◽  
Gas Turbine ◽  
Thermal Efficiency ◽  
High Efficiency ◽  
Development Program ◽  
Pollutant Emissions ◽  
Inlet Temperature ◽  
Term Operation ◽  
Ceramic Components

The Japanese Ceramic Gas Turbine (CGT) research and development program (FY1988–1998) as a part of the New Sunshine Project funded by the Ministry of International Trade and Industry (MITI) was completed in March 1999. Kawasaki Heavy Industries, Ltd. (KM) participated in this research program from the beginning and developed a twin-shaft CGT with a recuperator, designated as the “CGT302”. The purposes of this program were: 1) to achieve both a high efficiency and low pollutant emissions level using ceramic components, 2) to prove a multi-fuel capability to be used in co-generation systems, and 3) to demonstrate long-term operation. The targets of this program were: i) to achieve a thermal efficiency of over 42% at a turbine inlet temperature (TIT) of 1350°C, ii) to keep its emissions within the regulated value by the law, and iii) to demonstrate continuous operation for more than a thousand hours at 1200°C TIT. The CGT302 has successfully attained its targets. In March 1999 the CGT302 recorded 42.1% thermal efficiency, and 31.7 ppm NOx emissions (O2 = 16%) at 1350°C TIT. At this time it had also accumulated over two thousand hours operation at 1200°C. In this paper, we summarize the development of the CGT302.

Summary of CGT302 Ceramic Gas Turbine Research and Development Program

2002 ◽  
Vol 124 (3) ◽  
pp. 627-635 ◽  
Author(s):  
I. Takehara ◽  
T. Tatsumi ◽  
Y. Ichikawa
Keyword(s):  
Research And Development ◽  
Gas Turbine ◽  
Thermal Efficiency ◽  
High Efficiency ◽  
Development Program ◽  
Pollutant Emissions ◽  
Inlet Temperature ◽  
Term Operation ◽  
Ceramic Components

The Japanese ceramic gas turbine (CGT) research and development program (FY1988-1998) as a part of the New Sunshine Project funded by the Ministry of International Trade and Industry (MITI) was completed in March 1999. Kawasaki Heavy Industries, Ltd. (KHI) participated in this research program from the beginning and developed a twin-shaft CGT with a recuperator, designated as the “CGT302.” The purposes of this program were (1) to achieve both a high efficiency and low pollutant emissions level using ceramic components, (2) to prove a multifuel capability to be used in cogeneration systems, and (3) to demonstrate long-term operation. The targets of this program were (i) to achieve a thermal efficiency of over 42 percent at a turbine inlet temperature (TIT) of 1350°C, (ii) to keep its emissions within the regulated value by the law, and (iii) to demonstrate continuous operation for more than a thousand hours at 1200°C TIT. The CGT302 has successfully attained its targets. In March 1999 the CGT302 recorded 42.1 percent thermal efficiency, and 31.7 ppm NOx emissions (O2=16 percent) at 1350°C TIT. At this time it had also accumulated over 2000 hours operation at 1200°C. In this paper, we summarize the development of the CGT302.

Low Emissions Combustor Development for an Industrial Gas Turbine to Utilize LCV Fuel Gas

1994 ◽  
Vol 116 (3) ◽  
pp. 559-566 ◽  
Author(s):  
G. J. Kelsall ◽  
M. A. Smith ◽  
M. F. Cannon
Keyword(s):  
Gas Turbine ◽  
High Efficiency ◽  
Development Program ◽  
Calorific Value ◽  
Pollutant Emissions ◽  
Inlet Temperature ◽  
Second Phase ◽  
Fuel Gas ◽  
Topping Cycle ◽  
Industrial Gas Turbine

Advanced coal-based power generation systems such as the British Coal Topping Cycle offer the potential for high-efficiency electricity generation with minimum environmental impact. An important component of the Topping Cycle program is the gas turbine, for which development of a combustion system to burn low calorific value coal derived fuel gas, at a turbine inlet temperature of 1260°C (2300°F), with minimum pollutant emissions, is a key R&D issue. A phased combustor development program is underway burning low calorific value fuel gas (3.6-4.1 MJ/m3) with low emissions, particularly NOx derived from fuel-bound nitrogen. The first phase of the combustor development program has now been completed using a generic tubo-annular, prototype combustor design. Tests were carried out at combustor loading and Mach numbers considerably greater than the initial design values. Combustor performance at these conditions was encouraging. The second phase of the program is currently in progress. This will assess, initially, an improved variant of the prototype combustor operating at conditions selected to represent a particular medium sized industrial gas turbine. This combustor will also be capable of operating using natural gas as an auxiliary fuel, to suit the start-up procedure for the Topping Cycle. The paper presents the Phase 1 test program results for the prototype combustor. Design of the modified combustor for Phase 2 of the development program is discussed, together with preliminary combustion performance results.

Sign in / Sign up

Export Citation Format

Share Document