A Parallel Six Degrees-of-Freedom Inflatable Robot

2000 ◽  
Author(s):  
Patricia Ben-Horin (Dombiak) ◽  
Moshe Shoham ◽  
Gershon Grossman
Keyword(s):  
Path Planning ◽  
Degrees Of Freedom ◽  
Parallel Robot ◽  
Six Degrees Of Freedom ◽  
Robot Architecture

Abstract A new structure of a six degrees-of-freedom robot is described in this paper. The robot presents two new features: three inflatable links that constitute the robot structure and parallel robot architecture with large workspace. These features result in a lightweight and easy to deploy robot. The structure, kinematics and path planning of the experimental robot are presented.

Construction of a Six-Degrees-of-Freedom Parallel Manipulator With Three Planarly Actuated Links

1996 ◽  
Author(s):  
Ronen Ben-Horin ◽  
Moshe Shoham
Keyword(s):  
Parallel Manipulator ◽  
High Performance ◽  
Degrees Of Freedom ◽  
Parallel Robot ◽  
Simple Design ◽  
Output Link ◽  
Coordinated Motion ◽  
Six Degrees Of Freedom ◽  
Work Volume ◽  
New Type

Abstract The construction of a new type of a six-degrees-of-freedom parallel robot is presented in this paper. Coordinated motion of three planar motors, connected to three fixed-length links, produces a six-degrees-of-freedom motion of an output link. Its extremely simple design along with much larger work volume make this high performance-to-simplicity ratio robot very attractive.

Offline decoupled path planning approach for effective coordination of multiple robots

Robotica ◽  
2009 ◽  
Vol 28 (4) ◽  
pp. 477-491 ◽  
Author(s):  
Shital S. Chiddarwar ◽  
N. Ramesh Babu
Keyword(s):  
Path Planning ◽  
Free Path ◽  
Minimum Distance ◽  
Degrees Of Freedom ◽  
Multiple Robots ◽  
A Algorithm ◽  
Two Phase ◽  
Six Degrees Of Freedom ◽  
Planning Approach ◽  
End Effectors

SUMMARYIn this paper, a decoupled offline path planning approach for determining the collision-free path of end effectors of multiple robots involved in coordinated manipulation is proposed. The proposed approach for decoupled path planning is a two-phase approach in which the path for coordinated manipulation is generated with a coupled interaction between collision checking and path planning techniques. Collision checking is done by modelling the links and environment of robot using swept sphere volume technique and utilizing minimum distance heuristic for interference check. While determining the path of the end effector of robots involved in coordinated manipulation, the obstacles present in the workspace are considered as static obstacles and the links of the robots are viewed as dynamic obstacles by the other robot. Coordination is done in offline mode by implementing replanning strategy which adopts incremental A* algorithm for searching the collision-free path. The effectiveness of proposed decoupled approach is demonstrated by considering two examples having multiple six degrees of freedom robots operating in 3D work cell environment with certain static obstacles.

Experiments on Linear and Nonlinear Control of a Multi-DOF Parallel Mechanism

2003 ◽  
Author(s):  
Sandor Riebe ◽  
Heinz Ulbrich
Keyword(s):  
Degrees Of Freedom ◽  
Motion Tracking ◽  
Parallel Robot ◽  
Parallel Kinematics ◽  
Control Laws ◽  
Six Degrees Of Freedom ◽  
Position Accuracy ◽  
Nonlinear Approach ◽  
Linear Approach ◽  
Measurement Results

Parallel kinematics with multi degrees-of-freedom (DOF), like hexapod-systems, are mostly used in applications where high demands on position accuracy are required and/or high accelerations are needed. Adequate control concepts are essential in order to achieve the desired dynamic response. This paper deals with a comparative study of two structural different control concepts applied on a parallel robot with six degrees-of-freedom. The first one is a decentral linear approach and the second one is a multivariable nonlinear approach. The two concepts are presented and implemented on an experimental hexapod-system. In order to verify the used dynamic model comparisons between simulation and measurement results are shown. Finally, experiments have been carried out to compare the control laws with respect to their motion tracking performance.

The Wide-Open Three-Legged Parallel Robot for Long-Bone Fracture Reduction

2017 ◽  
Vol 9 (1) ◽  
Author(s):  
Mohammad H. Abedinnasab ◽  
Farzam Farahmand ◽  
Jaime Gallardo-Alvarado
Keyword(s):  
Bone Fracture ◽  
Degrees Of Freedom ◽  
Experimental Tests ◽  
Parallel Robot ◽  
High Accuracy ◽  
Fracture Reduction ◽  
Long Bone ◽  
Long Bones ◽  
Six Degrees Of Freedom ◽  
Long Bone Fracture

Robotic reduction of long bones is associated with the need for considerable force and high precision. To balance the accuracy, payload, and workspace, we have designed a new six degrees-of-freedom three-legged wide-open robotic system for long-bone fracture reduction. Thanks to the low number of legs and their nonsymmetrical configuration, the mechanism enjoys a unique architecture with a frontally open half-plane. This facilitates positioning the leg inside the mechanism and provides a large workspace for surgical maneuvers, as shown and compared to the well-known Gough–Stewart platform. The experimental tests on a phantom reveal that the mechanism is well capable of applying the desired reduction steps against the large muscular payloads with high accuracy.

Reconfiguration Analysis of a Fully Reconfigurable Parallel Robot

2013 ◽  
Vol 5 (4) ◽  
Author(s):  
Allan Daniel Finistauri ◽  
Fengfeng (Jeff) Xi
Keyword(s):  
Comparative Study ◽  
Degrees Of Freedom ◽  
Parallel Robot ◽  
Passive State ◽  
Limited Mobility ◽  
Six Degrees Of Freedom ◽  
Revolute Joints ◽  
Six Degree Of Freedom ◽  
The Comparative Study ◽  
Selection Of

This paper presents a new method for the combined topological and geometric reconfiguration of a parallel robot to achieve task-based reconfiguration. Using the existing structure of a six degree-of-freedom (DOF) parallel robot, reconfiguration to limited mobility modes, a configuration with less than six degrees-of-freedom, can be achieved easily without the need to remove branches from the robot structure. Branch modules are instead, reconfigured from an unconstrained-active to a constrained-passive state by means of hybrid active/passive motors and reconfigurable universal-to-revolute joints. In doing so, the robot is capable of assuming a configuration in which the number of task-based degrees-of-freedom match the number of controllable actuators within the robot structure. The selection of branch modules for reconfiguration is independent of the limited mobility mode required and leads to multiple isomorphic configurations. A comparative study is thus needed to understand not only the implication of morphing, but also the capabilities of the reconfigured robot. For this purpose, a branch-based mobility analysis is performed and isomorphic configurations are identified. These isomorphic configurations are then compared based on their workspace and kinematic capabilities for which a parametric kinematic constraint formulation is developed. The comparative study evaluates the abilities of each configuration and is used for guidance in selecting an appropriate configuration for a particular task. The developed tools can also be used for design evaluation purposes.

Kinematic analysis and path planning of a new kinematically redundant planar parallel manipulator

Robotica ◽  
2008 ◽  
Vol 26 (3) ◽  
pp. 405-413 ◽  
Author(s):  
Iman Ebrahimi ◽  
Juan A. Carretero ◽  
Roger Boudreau
Keyword(s):  
Path Planning ◽  
Condition Number ◽  
Kinematic Analysis ◽  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Six Degrees Of Freedom ◽  
Displacement Problem ◽  
Singular Configurations ◽  
Planar Parallel Manipulator

SUMMARYIn this work, the 3-RPRR, a new kinematically redundant planar parallel manipulator with six-degrees-of-freedom, is presented. First, the manipulator is introduced and its inverse displacement problem discussed. Then, all types of singularities of the 3-RPRR manipulator are analysed and demonstrated. Thereafter, the dexterous workspace is geometrically obtained and compared with the non-redundant 3-PRR planar parallel manipulator. Finally, based on a geometrical measure of proximity to singular configurations and the condition number of the manipulators' Jacobian matrices, actuation schemes for the manipulators are obtained. Different actuation schemes for a given path are obtained and the quality of their actuation schemes are compared. It is shown that the proposed manipulator is capable of following a path while avoiding the singularities.

Six degrees of freedom parallel robots with C5 links

Robotica ◽  
1992 ◽  
Vol 10 (1) ◽  
pp. 35-44 ◽  
Author(s):  
Y. Amirat ◽  
F. Artigue ◽  
J. Pontnau
Keyword(s):  
Automotive Industry ◽  
Kinematic Analysis ◽  
Degrees Of Freedom ◽  
Parallel Architecture ◽  
Parallel Robot ◽  
Parallel Architectures ◽  
Parallel Robots ◽  
Left Hand ◽  
Six Degrees Of Freedom ◽  
Assembly Tasks

SummaryThis paper presents at first a static and kinematic analysis of closed chains mechanisms which permits to deduce different possible fully parallel architectures. Then we focus on a particular parallel architecture with C5 links designed to perform precise assembly tasks. A general modeling of this C5 parallel robot is presented. Two typical assembly tasks in the automotive industry are also proposed; the first one uses the C5 links parallel robot as a left-hand device, while the second one uses it as the terminal tool of a sequential manipulator.

Sign in / Sign up

Export Citation Format

Share Document