scholarly journals Wear of Spur Gears Having a Dithering Motion and Lubricated With a Perfluorinated Polyether Grease

2007 ◽  
Author(s):  
Timothy Krantz ◽  
Fred Oswald ◽  
Robert Handschuh
Keyword(s):  
Wear Rate ◽  
High Speed ◽  
Failure Modes ◽  
Load Level ◽  
Wear Depth ◽  
Spur Gears ◽  
Test Load ◽  
Total Wear ◽  
Gear Contact ◽  
Perfluorinated Polyether

Gear contact surface wear is one of the important failure modes for gear systems. Dedicated experiments are required to enable precise evaluations of gear wear for a particular application. The application of interest for this study required evaluation of wear of gears lubricated with a grade 2 perfluorinated polyether grease and having a dithering (rotation reversal) motion. Experiments were conducted using spur gears made from AISI 9310 steel. Wear was measured using a profilometer at test intervals encompassing 10,000 to 80,000 cycles of dithering motion. The test load level was 1.1 GPa maximum Hertz contact stress at the pitch-line. The trend of total wear as a function of test cycles was linear, and the wear depth rate was approximately 1.2 nm maximum wear depth per gear dithering cycle. The observed wear rate was about 600 times greater than the wear rate for the same gears operated at high speed and lubricated with oil.

A Virtual Tool for Wear Simulation of Standard and Non-Standard Spur Gears

2012 ◽  
Author(s):  
F. Karpat ◽  
S. Ekwaro-Osire ◽  
E. Karpat
Keyword(s):  
High Speed ◽  
High Performance ◽  
Failure Modes ◽  
Power Transmission ◽  
Wear Behavior ◽  
Gear Tooth ◽  
Load Capacity ◽  
High Load ◽  
Wear Depth ◽  
Spur Gears

There is an industrial demand for the increased performance of mechanical power transmission devices. This need in high performance is driven by high load capacity, high endurance, low cost, long life, and high speed. New designs and modifications in gears have been investigated to obtain high load carrying capacity and increased life with less volume and weight. Tooth wear is one of the major failure modes in gears. Although there are different classifications of wear mechanisms, wear on gears can be simply classified as mild wear, pitting, and severe wear, depending on the wear rate. These types of wear may lead to power transmission losses, decreased efficiency, increased vibration and noise, and gear tooth failure. This paper deals with the simulation of wear for standard and non-standard gears using an analytical approach. A numerical model for wear prediction of gear pair is developed. A wear model based on Archard’s equation is employed to predict wear depth. A MATLAB-based virtual tool is developed to analyze wear behavior of standard and non-standard spur gears with various gear parameters. In this paper, this virtual tool is introduced by using many numerical examples.

A Virtual Tool for Wear Simulation of Plastic Gear Pairs

2013 ◽  
Author(s):  
F. Karpat ◽  
S. Ekwaro-Osire ◽  
C. Yüce ◽  
E. Karpat
Keyword(s):  
Analytical Approach ◽  
Failure Modes ◽  
Wear Behavior ◽  
Load Capacity ◽  
Tooth Wear ◽  
Wear Depth ◽  
Spur Gears ◽  
Automotive Applications ◽  
Wear Model ◽  
Plastic Gears

Currently plastic gears are widely used in industry, and not only for lightly loaded applications like household appliances, tools, and toys, but also in the more demanding areas of machinery in automotive applications. However there is a need to investigate important properties such as load capacity, endurance, cost, life, stiffness and wear. Tooth wear is one of the major failure modes in plastic gears just like with steel gears. This paper focuses on the simulation of wear for standard and non-standard gears using an analytical approach. A numerical model for wear prediction of gear pairs is developed. A wear model based on Archard’s equation is employed to predict wear depth. The variation of the contact load generated by the cumulative tooth profile wear is simulated and examined. A MATLAB-based virtual tool is developed to analyze wear behavior of standard and non-standard spur gears depending on various gear parameters. In this paper, this virtual tool is introduced with numerical examples.

Wear of Involute Spur Gears With Asymmetric Teeth Under Dynamic Loading

Tribology ◽  
2006 ◽  
Author(s):  
F. Karpat ◽  
S. Ekwaro-Osire
Keyword(s):  
Aerospace Industry ◽  
Tooth Wear ◽  
Wear Depth ◽  
Spur Gears ◽  
Contact Ratio ◽  
Mesh Stiffness ◽  
Wear Model ◽  
Extreme Performance ◽  
Gear Contact ◽  
The Relationship

Spur gears with asymmetric teeth have a significant potential for some applications requiring extreme performance like in the aerospace industry. In this study, the influence of tooth wear on the dynamic behavior of involute spur gears with asymmetric teeth is analyzed. The Archard's wear model was adopted in formulating and accounting for wear. Effects of gear parameters such as gear contact ratio, tooth height, mesh stiffness, and pressure angles on tooth wear are considered. These parameters are used to describe the relationship between dynamic tooth load and tooth wear. A comparison of symmetric and asymmetric teeth is also presented with respect to tooth wear. Sample simulation results, which were obtained by using an in-house developed computer program, are illustrated with numerical examples. The numerical results match well with the practical and analytical results which are available in literature. For asymmetric teeth, it was shown that the wear depth decreased with increasing pressure angle on drive side.

Development of a Dynamometer to Study the Performance of Plastic Gears

2007 ◽  
Author(s):  
Mike Cassata ◽  
Martin Morris ◽  
Jorge Abanto-Bueno
Keyword(s):  
High Speed ◽  
Failure Modes ◽  
Gear Tooth ◽  
Digital Camera ◽  
Operating Conditions ◽  
Spur Gears ◽  
Camera System ◽  
Dupont Company ◽  
Plastic Gears ◽  
Flank Surface

A testing facility has been developed to explore the failure modes of plastic gears. The overall goal is the prediction of gear tooth failure for a given set of operating conditions and to classify failure modes of plastic gears. The initial investigation is centered on the testing of plastic spur gears placed on a parallel-shaft drive train between a variable-speed, reversible DC motor and an eddy current dynamometer. The testing apparatus has been designed, fabricated, and refined to deliver consistent results. The dynamometer places two plastic spur gears in mesh, one being the drive gear and the other the driven. Most of the test gear pairs were injection molded, 40-tooth, 0.8 module gears. These gears were molded using Delrin™ 311DP, a polyoxymethylene polymer which is made by the DuPont Company. Optical encoders were attached to the input and output shafts to sense the shaft position providing a measurement of the deflection and wear of the gear teeth. In addition, an infrared temperature sensor was retrofitted to the dynamometer apparatus to measure the tooth-flank surface temperature. All of the tests where the gear flank temperature reached 250°F resulted in a catastrophic failure. The apparatus was also fitted with a high-speed digital camera system capable of sampling 1000 frames per second. The camera recorded the failure of the plastic gears.

A Prediction Method of Wear on Tooth Surface for Spur Gears

2013 ◽  
Author(s):  
Shotaro Inoue ◽  
Kiyotaka Ikejo ◽  
Kazuteru Nagamura ◽  
Natsuhiko Seyama ◽  
Shinya Nakagawa
Keyword(s):  
Failure Modes ◽  
Gear Tooth ◽  
Testing Machine ◽  
Prediction Method ◽  
Tooth Wear ◽  
Spur Gear ◽  
Tooth Surface ◽  
Wear Depth ◽  
Spur Gears ◽  
Gear Drives

Gear drives are widely used in various mechanical systems. Therefore, the understanding for the failure mode of gear tooth provides the improvement of various machines. The wear on the tooth surface is one of the important failure modes for the gear drives. The tooth wear changes its profile, and frequently increases gear vibration and noise. However, there are many unclear phenomena about the wear on the tooth surface for the gear drive. In this study, we investigated wear of spur gear using a power circulating-type gear testing machine, and measured the change in tooth profile of the test gears. Furthermore, we developed a computer program to predict the amount of the wear on the tooth surface for the spur gears. The method employs two equations. One is based on the wear theory under lubricated condition that was deduced by Soda. The other is derived from the ploughing wear model. Using these equations, the wear depth on the tooth surface is calculated with the contact stress, the sliding velocity, the oil film thickness, etc. The calculated value of the wear agreed with the experimental data.

scholarly journals Sliding Wear of Conventional and Suspension Sprayed Nanocomposite WC-Co Coatings: An Invited Review

2021 ◽  
Author(s):  
R. Ahmed ◽  
O. Ali ◽  
C. C. Berndt ◽  
A. Fardan
Keyword(s):  
Wear Rate ◽  
Thermal Spray ◽  
Sliding Wear ◽  
Failure Modes ◽  
Thermal Spray Coatings ◽  
Annual Growth Rate ◽  
Total Energy Consumption ◽  
Wear Performance ◽  
Wear Rates ◽  
Spray Coatings

AbstractThe global thermal spray coatings market was valued at USD 10.1 billion in 2019 and is expected to grow at a compound annual growth rate of 3.9% from 2020 to 2027. Carbide coatings form an essential segment of this market and provide cost-effective and environmental friendly tribological solutions for applications in aerospace, industrial gas turbine, automotive, printing, oil and gas, steel, and pulp and paper industries. Almost 23% of the world’s total energy consumption originates from tribological contacts. Thermal spray WC-Co coatings provide excellent wear resistance for industrial applications in sliding and rolling contacts. Some of these applications in abrasive, sliding and erosive conditions include sink rolls in zinc pots, conveyor screws, pump housings, impeller shafts, aircraft flap tracks, cam followers and expansion joints. These coatings are considered as a replacement of the hazardous chrome plating for tribological applications. The microstructure of thermal spray coatings is however complex, and the wear mechanisms and wear rates vary significantly when compared to cemented WC-Co carbides or vapour deposition WC coatings. This paper provides an expert review of the tribological considerations that dictate the sliding wear performance of thermal spray WC-Co coatings. Structure–property relationships and failure modes are discussed to grasp the design aspects of WC-Co coatings for tribological applications. Recent developments of suspension sprayed nanocomposite coatings are compared with conventional coatings in terms of performance and failure mechanisms. The dependency of coating microstructure, binder material, carbide size, fracture toughness, post-treatment and hardness on sliding wear performance and test methodology is discussed. Semiempirical mathematical models of wear rate related to the influence of tribological test conditions and coating characteristics are analysed for sliding contacts. Finally, advances for numerical modelling of sliding wear rate are discussed.

scholarly journals The Influence of the Axial Rub Added in the Radial Rub on the Wear of the Seal Fins during the High Speed Rub of Labyrinth-Honeycomb Seal

Materials ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 1997
Author(s):  
Bin Lu ◽  
Haijun Xuan ◽  
Xiaojian Ma ◽  
Fangjun Han ◽  
Weirong Hong ◽  
...  
Keyword(s):  
Wear Rate ◽  
High Speed ◽  
State Of The Art ◽  
Negative Influence ◽  
Axial Thrust ◽  
Cross Sectional ◽  
Honeycomb Seal ◽  
Aero Engine ◽  
Honeycomb Seals ◽  
Clearance Change

Labyrinth-honeycomb seals are a state-of-the-art sealing technology commonly used in aero-engine interstage seal. The undesirable severe rub between the seal fins and the honeycomb due to the clearance change may induce the cracking of the seal fins. A pervious study investigated the wear of the seal fins at different radial incursion rates. However, due to the axial thrust and mounting clearance, the axial rub between the seal fins and the honeycomb may occur. Hence, this paper focuses on the influence of the axial rub added in the radial rub on the wear of the seal fins. The rub tests results, including rubbing forces and temperature, wear rate, worn morphology, cross-sectional morphology and energy dispersive spectroscopy results, are presented and discussed. Overall, the participation of the axial rub leads to higher rubbing forces, temperature, and wear rate. The tribo-layer on the seal fin is thicker and the cracks are more obvious at high axial incursion rate. These phenomena indicate the axial rub has a negative influence on the wear of the seal fins and should be avoided.

High-speed electrical sliding wear behaviors of Cu-WS2-graphite-WS2 nanotubes composite

2018 ◽  
Vol 25 (2) ◽  
pp. 343-351
Author(s):  
Gang Qian ◽  
Yi Feng ◽  
Jing-Cheng Zhang ◽  
Yang Wang ◽  
Tian-Ci Zhang ◽  
...  
Keyword(s):  
Wear Rate ◽  
Contact Resistance ◽  
Photoelectron Spectroscopy ◽  
High Speed ◽  
Electrical Current ◽  
Tangential Direction ◽  
Sliding Velocity ◽  
Graphite Composite ◽  
Slip Ring ◽  
Electrical Wear

AbstractCu-WS2-graphite-WS2nanotubes composite was fabricated by the powder metallurgy hot-pressed method. The effects of electrical current (5–15 A/cm2) and sliding velocity (5–15 m/s) on the electrical wear behaviors of the composite were investigated using a block-on-slip ring wear tester rubbing against Cu-5 wt% Ag alloy ring under 2.5 N/cm2of applied load. The lubricating effect of WS2nanotubes and composition of tribo-film were analyzed. The results demonstrated that the contact resistance decreases but the wear rate increases as electrical current increases, because the adverse effects of electrical current soften the materials at “a-spots” and damage the tribo-film. Due to the adsorption of gaseous molecule film on the tangential direction of slip ring surface, with the rise of sliding velocity, the contact resistance increases while the wear rate reaches the minimum at a sliding velocity of 10 m/s. The reasonable addition of WS2nanotubes into the Cu-WS2-graphite composite to replace WS2powder can result in a reduction of both contact resistance and wear rate. X-ray photoelectron spectroscopy (XPS) analyses revealed that copper oxides, graphite, WS2and WS2nanotubes in the tribo-film play the main lubrication action at the tribo-interface.

scholarly journals Investigating the Effect of Interface Morphology in Adhesively Bonded Composite Wavy-Lap Joints

2021 ◽  
Vol 5 (1) ◽  
pp. 32
Author(s):  
Roya Akrami ◽  
Shahwaiz Anjum ◽  
Sakineh Fotouhi ◽  
Joel Boaretto ◽  
Felipe Vannucchi de Camargo ◽  
...  
Keyword(s):  
Mechanical Behavior ◽  
Composite Structures ◽  
Failure Modes ◽  
Mechanical Performance ◽  
Tensile Load ◽  
Lap Joints ◽  
Load Level ◽  
Displacement Curve ◽  
Interface Morphology ◽  
Angle Variation

Joints and interfaces are one of the key aspects of the design and production of composite structures. This paper investigates the effect of adhesive–adherend interface morphology on the mechanical behavior of wavy-lap joints with the aim to improve the mechanical performance. Intentional deviation from a flat joint plane was introduced in different bond angles (0°, 60°, 90° and 120°) and the joints were subjected to a quasi-static tensile load. Comparisons were made regarding the mechanical behavior of the conventional flat joint and the wavy joints. The visible failure modes that occurred within each of the joint configurations was also highlighted and explained. Load vs. displacement graphs were produced and compared, as well as the failure modes discussed both visually and qualitatively. It was observed that distinct interface morphologies result in variation in the load–displacement curve and damage types. The wavy-lap joints experience a considerably higher displacement due to the additional bending in the joint area, and the initial damage starts occurring at a higher displacement. However, the load level had its maximum value for the single-lap joints. Our findings provide insight for the development of different interface morphology angle variation to optimize the joints behavior, which is widely observed in some biological systems to improve their performance.

scholarly journals EFFECT OF DIFFRENT LOADS ON THE WEAR BEHAVIORS OF 5Cr5Mo2V STEEL AT 700 °C

2021 ◽  
Vol 55 (6) ◽  
Author(s):  
Zhixiong Bai ◽  
Hang Yang ◽  
Ning Su ◽  
Xiaochun Wu
Keyword(s):  
High Temperature ◽  
Crack Initiation ◽  
Wear Rate ◽  
Wear Behavior ◽  
Oxidative Wear ◽  
Test Load ◽  
High Temperature Wear ◽  
Holding Power ◽  
The Matrix ◽  
Matrix Evolution

The effect of different loads on the high-temperature wear behavior of 5Cr5Mo2V steel at 700 °C was investigated. Wear morphologies, oxide compositions and matrix evolution were studied. The results showed that the wear rate increased with an increased test load, and the wear mechanism transformed from abrasive-oxidative wear to adhesive-oxidative wear. The relation between a delaminated oxide layer and cracks in the matrix were investigated. The exfoliation of carbides and displacement difference between the matrix and carbides caused a crack initiation. The wear rate strongly related to carbides, and coarse M6C carbides with poor holding power led to a high wear rate. Besides, a diagram of wear characteristics under different loads was suggested in this work.

Sign in / Sign up

Export Citation Format

Share Document