Peak-Shaving Ratio Analysis of the Natural Gas Combined Heat and Power Plant With Distributed Peak-Shaving Heat Pumps

Author(s):  
Xiling Zhao ◽  
Xiaoyin Wang ◽  
Tao Sun

Distributed peak-shaving heat pump technology is to use a heat pump to adjust the heat on the secondary network in a substation, with features of low initial investment, flexible adjustment, and high operating cost. The paper takes an example for the system that uses two 9F class gas turbines (back pressure steam) as the basic heat source and a distributed heat pump in the substation as the peak-shaving heat source. The peak-shaving ratio is defined as the ratio of the designed peak-shaving heat load and the designed total heat load. The economic annual cost is taken as a goal, and the optimal peak-shaving ratio of the system is investigated. The influence of natural gas price, electricity price, and transportation distance are also analyzed. It can provide the reference for the optimized design and operation of the system.

Energies ◽  
2021 ◽  
Vol 14 (1) ◽  
pp. 226
Author(s):  
Milana Treshcheva ◽  
Irina Anikina ◽  
Vitaly Sergeev ◽  
Sergey Skulkin ◽  
Dmitry Treshchev

The percentage of heat pumps used in thermal power plants (TPPs) in the fuel and energy balance is extremely low in in most countries. One of the reasons for this is the lack of a systematic approach to selecting and justifying the circuit solutions and equipment capacity. This article aims to develop a new method of calculating the maximum capacity of heat pumps. The method proposed in the article has elements of marginal analysis. It takes into account the limitation of heat pump capacity by break-even operation at electric power market (compensation of fuel expenses, connected with electric power production). In this case, the heat pump’s maximum allowable capacity depends on the electric capacity of TPP, electricity consumption for own needs, specific consumption of conditional fuel for electricity production, a ratio of prices for energy resources, and a conversion factor of heat pump. For TPP based on combined cycle gas turbine (CCGT) CCGT-450 with prices at the Russian energy resources markets at the level of 2019, when operating with the maximum heat load, the allowable heat pump capacity will be about 50 MW, and when operating with the minimum heat load—about 200 MW.


Author(s):  
Yuefen Gao ◽  
Songling Wang ◽  
Guoqiang Zhang

Ground-coupled heat pump systems use the ground as a heat source and sink either with vertical or horizontal ground heat exchangers (GHXs) to supply heating in winter and cooling in summer. The ground heat source and sink has a near constant temperature, which is well suited to ground-coupled heat pumps, giving them consistent performance, regardless of the outdoor temperature. However, when the heat extracted from and rejected to the ground has great imbalance, the ground temperature will deviate from the original temperature with a long term operation. The deviation can reduce GHX performance greatly. As China has vast territory with variety climate, the annual cooling loads and heating loads are different at different places. And the imbalance between the extracted heat and the rejected heat also varies at different places. Therefore, it is necessary to analysis the regional suitability of the ground-coupled heat pump systems. The imbalance between the extracted heat and the rejected heat is analyzed by taking several typical cities in different climates. The new concepts of the Imbalance Ratio and the Extracted Heat to Rejected Heat Ratio are introduced as the weight factors to measure the imbalance in the ground. The values of the Imbalance Ratio and those of the Extracted Heat to the Rejected Heat Ratio are calculated. The optimum range of the Imbalance Ratio is recommended based on the vast investigation of the ground-coupled heat pumps. Some supplemental systems are put forward to supply heat in winter or to reject heat in summer at the places existing serious heat imbalance. The study is very meaningful to the scientific application of the ground-coupled heat pump systems in China.


2020 ◽  
Vol 154 ◽  
pp. 04003
Author(s):  
Elżbieta Hałaj

Heat pumps become more and more popular heat source. They can be an alternative choice for obsolete coal fired boilers which are emissive and not ecological. During heat pump installation designing process, especially for heat pumps with higher heating capacity (for example those suppling larger buildings), a simulation of heat balance of ground heat source must be provided. A 3D heat transport model and groundwater flow in the geothermal heat source for heat pump (GSHP) installation was developed in FEFLOW according to Finite Element Modelling Method. The model consists of 25 borehole heat exchangers, arranged with spacing recommended by heat pump branch guidelines. The model consists of both a homogeneous, non-layered domain and a layered domain, which reflected differences in thermal properties of the ground and hydrogeological factors. The initial temperature distribution in the ground was simulating according to conditions typical for Europe in steady state heat flow. Optimal mesh refinement for nodes around borehole heat exchangers were calculated according to Nillert method. The aim of this work is to present influence of geological, hydrogeological factors and borehole arrangement in the energy balance and long term sustainability of the ground source. The thermal changes in the subsurface have been determined for a long term operation (30 years of operation period). Some thermal energy storage applications have also been considered.


2012 ◽  
Vol 170-173 ◽  
pp. 2743-2746
Author(s):  
Feng Li ◽  
Zhe Tian ◽  
Qiang Fu ◽  
Qian Ru Li

The double-energy heating system studied in this paper is consisted of centrifugal sewage-source heat pumps and gas boilers. As the grade and price of the two kinds of energy are different, the heating capacity of the heat-source equipments would have a directly impact on the energy consumption and operating cost of the system. In order to obtain the optimal heating capacity of the heat-source equipments, the calculation models on equipments utilized in this system are firstly established, and then different combination patterns of the heat-source equipments were analyzed on the basis of minimum operating cost, finally, the optimal heating capacity of the heat-source equipments and the heating performance factor (HPF) of the system in different outdoor temperatures were obtained, the results indicate the average HPF of the system in the heating period is 3.57. The method and results provide reference for scientific design of the double-energy heating system.


1996 ◽  
Vol 118 (4) ◽  
pp. 300-305 ◽  
Author(s):  
M. T. Kangas

In this study, the use of the ground as the heat source for a heat pump was studied by computer simulation. The heat extraction system consisted of vertical pipes drilled into the ground where groundwater was present. Along with available thermal energy, potential environmental effects, such as freezing and thermal pollution, were examined. It was found that the presence of groundwater enhances system performance by decreasing the possibility of freezing but, on the other hand, increases the range of thermal effects in the ground. The temperature of the ground as well as extraction arrangements also have a significant effect on system performance.


2020 ◽  
Vol 12 (7) ◽  
pp. 1093
Author(s):  
Ignacio Martín Nieto ◽  
David Borge-Diez ◽  
Cristina Sáez Blázquez ◽  
Arturo Farfán Martín ◽  
Diego González-Aguilera

This research work aims at a multinational study in Europe of the emissions and energy costs generated by the operation of low enthalpy geothermal systems, with heat pumps fed by different energy sources. From an economic point of view, natural gas and biogas prices are, usually, lower than electricity ones. So it may be advantageous to use these energy sources to feed the heat pumps instead of electricity. From the environmental point of view, it is intended to highlight the fact that under certain conditions of electricity production (electricity mix), more CO2 emissions are produced by electricity consumption than using other a priori less “clean” energy sources such as natural gas. To establish the countries where each of the different heat pumps may be more cost-efficient and environmentally friendly, data from multi-source geospatial databases have been collected and analyzed. The results show that in the majority of cases, the electric heat pump is the most recommendable solution. However, there are some geographic locations (such as Poland and Estonia), where the gas engine heat pump may be a better alternative.


2014 ◽  
Vol 953-954 ◽  
pp. 650-654
Author(s):  
Chao Yi Tan ◽  
Hui Zhu ◽  
Hai Hua Hu ◽  
Meng Meng Wang ◽  
Han Qing Wang

Taking the geothermal heat pump system in the campus of Hunan University of Technology for example, three technical solutions of the heat source of the system were analyzed in terms of the condensing heat load, the annual unbalanced heat load and the energy efficiency ratio (EER) of the system. In addition, comparison was conducted among the solutions. The results indicate that the solution 3, which has a cold and hot water integrative unit and hot water unit connected in series, meanwhile has a cooling tower for auxiliary cooling, shows better performance among all the solutions. The analysis on the solution of heat source of geothermal heat pump system, which usually contains the analysis on the condensing heat load, annual unbalanced heat load and EER, is of great significance for the design and development of the geothermal heat pump system with lower coat and higher EER.


2017 ◽  
Vol 111 ◽  
pp. 599-607 ◽  
Author(s):  
Xiling Zhao ◽  
Lin Fu ◽  
Xiaoyin Wang ◽  
Tao Sun ◽  
Jingyi Wang ◽  
...  

2021 ◽  
Author(s):  
Maudud Hassan Quazi

This objective of this project is to determine the energy and environmental potential of distributed common loop water source heat pump system in a near or net-zero commercial office building, which has simultaneous heating and cooling load in winter and shoulder seasons. It is expected that the perimeter zones will have heating demand during those months, while the core zones will have consistent cooling demand throughout the year. The motive is to reclaim the rejected heat from the cooling operation and transfer it to the zones requiring heating. The building under study is a 60,000 ft2 three storey commercial office building, which has private offices along the perimeter, and open work area in the core. In the first part of the analysis, the base building has been modelled and simulated to the minimum requirements of ASHRAE 90.1-Energy Standard for Buildings except Low-Rise Residential Buildings using simulation software eQuest 3.65. The Heating Ventilation and Airconditioning (HVAC) system used is four-pipe fan coil system serving individual zones. The fan coil units use a centralized natural gas boiler and a variable capacity centrifugal chiller as external source of heating and cooling respectively. The base case consumes a total of 524.54 x 1000 kWh of electricity and 1,056 million Btu of natural gas annually. The second part is the modelling and simulation of a proposed case, which uses the same building envelope, occupancy, lighting and equipment as the base case. The HVAC system used is a distributed common loop heat pump system connected to a cooling tower for heat rejection, and a condensing boiler for heat addition. During the occupied hours, when simultaneous cooling and heating loads exist in the building, the cooling zone heat pumps rejects exhaust heat into the common loop, and the heat is subsequently used by the heat pumps operating in heating mode. Using this method, the heat pump system reduces its dependence on the cooling tower and the boiler, which only operate to maintain the loop temperature in an acceptable range. There is 9,510 kWh (1.81%) increase in electricity consumption by proposed case comparing to the base building. Natural gas consumption has been reduced by 353.65 million Btu (33.48%). Annual utility bill has increased by $1,483.00 which is 1.88% higher than the base case. 15.7 tonnes of greenhouse gas can be reduced if the proposed case is adopted.


2015 ◽  
Vol 20 (3) ◽  
pp. 657-662
Author(s):  
R. Kłosowiak ◽  
J. Bartoszewicz ◽  
R. Urbaniak

Abstract The aim of this paper is to present the design and working principle of a portable testing device for heat pumps in the energy recirculation system. The presented test stand can be used for any refrigerating/reverse flow cycle device to calculate the device energy balance. The equipment is made of two portable containers of the capacity of 250 liters to simulate the air heat source and ground heat source with a system of temperature stabilization, compressor heat pump of the coefficient of performance (COP) of = 4.3, a failsafe system and a control and measurement system.


Sign in / Sign up

Export Citation Format

Share Document