Numerical Investigation of Steady Air Injection Flow to Control Rotating Stall in Centrifugal Compressors

2014 ◽  
Author(s):  
Taher Halawa ◽  
Mohamed Alqaradawi ◽  
Osama Badr ◽  
Mohamed S. Gadala
Keyword(s):  
Kinetic Energy ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Rotating Stall ◽  
Air Injection ◽  
Centrifugal Compressors ◽  
Injection Angle ◽  
Injection Method ◽  
Vane Angle

This paper concerns the role of air injection method in stabilization and stall control in centrifugal compressors. The main aim is to find the best arrangement of air injection parameters such as injection angle and injection mass flow rate in order to optimize the injection performance for stabilizing the compressor and increasing the surge margin. Numerical model was built to simulate high speed transonic centrifugal compressor working at an operating point close to surge. Air was injected at 12 locations at the vaneless region between the impeller and the diffuser at shroud surface with 5 different injection angles and 3 different injection mass flow rates. Results showed that the best injection method is when using an injection angle of 30° with injection mass flow rate of 1.5% of the design mass flow rate and the worst injection method is the injection at angle of 180° (reverse tangent injection). Results also indicated that by using air injection, the number of stalled diffuser passages is decreased compared to the case of no injection. The most significant result of this paper is that using an angle of injection around twice the value of the diffuser vane angle gives the best results and makes the ideal correction of the fluid kinetic energy and fluid angle at the diffuser inlet. It was found that injecting air at an angle less than the diffuser vane angle weakens the effect of injection and doesn’t increase kinetic energy of the fluid at diffuser inlet. It was also found that injecting air at an angle larger than the diffuser vane angle corrects the fluid direction but, at the same time, decreases the fluid kinetic energy at diffuser inlet.

Numerical Investigation of Rotating Stall Characteristics and Active Stall Control in Centrifugal Compressors

2014 ◽  
Author(s):  
Taher Halawa ◽  
Mohamed Alqaradawi ◽  
Osama Badr ◽  
Mohamed S. Gadala
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Rotating Stall ◽  
Air Injection ◽  
Tip Leakage Flow ◽  
Centrifugal Compressors ◽  
Flow Rates ◽  
Injection Angle ◽  
Mass Flow Rates

This paper focuses on providing better view for the understanding of rotating stall phenomenon in centrifugal compressors by using numerical simulations and presents a study of the role of air injection method in delaying stall inception by using different injection parameters aiming at increasing the efficiency of this method. Results showed that the formation of stall begins at the impeller inlet due to early flow separation at low mass flow rates and due to the increase of the turbulence level and the absence of fluid orientation guidance at the vaneless region. The flow weakness causes back flow that results in the formation of the tip leakage flow which causes stall development with time. Results also showed that using air injection at specified locations at the vaneless shroud surface at injection angle of 20° and with injection mass flow rate of 1.5% of the inlet design mass flow rate, can delay the stall onset to happen at lower mass flow rate about 3.8 kg/s comparing with using injection with angle of 10° with different injection mass flow rates and also comparing with the case of no injection.

Optimization of the Efficiency of Stall Control Using Air Injection for Centrifugal Compressors—Additional Findings

2018 ◽  
Vol 140 (12) ◽  
Author(s):  
Taher Halawa
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Gas Turbines ◽  
Stable Condition ◽  
Tangential Direction ◽  
Air Injection ◽  
Centrifugal Compressors ◽  
Injection Angle ◽  
Stall Control

This study presents additional important findings to the results of the research paper; “Optimization of the efficiency of stall control using air injection for centrifugal compressors” published in the Journal of Engineering for Gas Turbines and Power in 2015 (Halawa, T., Gadala, M. S., Alqaradawi, M., and Badr, O., 2015, “Optimization of the Efficiency of Stall Control Using Air Injection for Centrifugal Compressors,” ASME J. Eng. Gas Turbines Power, 137(7), p. 072604). The aim of this study is to make a fine determination of the injection angle, which provides the best stable condition when the compressor operates close to stall condition. A relatively narrower range of injection angles with smaller intervals was selected comparing to the results of the referred published paper, which clarified that the best injection angle is 30 deg. External air was injected close to the diffuser entrance at the shroud surface. Injection was applied with mass flow rate equals 1.5% of the design compressor inlet mass flow rate with injection angles ranged from 16 deg to 34 deg measured from the tangential direction at the vaneless region. It was found that both of injection angles of 28 deg and 30 deg achieved the best results in terms of compressor stabilization but each one of them has a specific advantage comparing to the other one. Using injection angle of 28 deg provided the lowest kinetic energy losses while the best orientation of the fluid through diffuser resulted when using an injection angle of 30 deg.

scholarly journals Characterizing the Effects of Air Injection on Compressor Performance for Use in Active Control of Rotating Stall

1997 ◽  
Author(s):  
Robert L. Behnken ◽  
Mina Leung ◽  
Richard M. Murray
Keyword(s):  
Hysteresis Loop ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Axial Flow ◽  
Open Loop ◽  
Rotating Stall ◽  
Air Injection ◽  
Loop Control ◽  
Flow Compression

Previous work has developed an air injection controller for rotating stall based on the idea of a shifting compressor characteristic and the Moore-Greitzer three state compressor model. In order to demonstrate this form of control experimentally, a series of open loop tests were performed to measure the performance characteristics of a low speed axial flow compression system when air is injected upstream of the rotor face. The position of the air injection port relative to the hub and the rotor face and the angle relative to the mean axial flow were varied. The tests show that the injection of air has drastic effects on the stalling mass flow rate and on the size of the hysteresis loop associated with rotating stall. The stalling mass flow rate was decreased by 10% and the hysteresis loop was completely eliminated under some conditions. The results of the open loop parametric study were then used to implement a closed loop control strategy based on a shifting characteristic.

Numerical Simulation of Stall Development Into Surge and Stall Control Using Air Injection in Centrifugal Compressors

2014 ◽  
Author(s):  
Taher Halawa ◽  
Mohamed Alqaradawi ◽  
Osama Badr ◽  
Mohamed S. Gadala
Keyword(s):  
Numerical Simulation ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Pressure Fluctuations ◽  
Air Injection ◽  
Good Effect ◽  
Sudden Increase ◽  
Centrifugal Compressors ◽  
Surge Margin

This study presents a numerical simulation of the formation of rotating stall and the initiation of surge in order to study the connection between stall and surge in centrifugal compressors. Also, the current paper introduces an optimization of the air injection method as a way to increase the surge margin. Results showed that during stall, the compressor is exposed to velocity and pressure fluctuations varying with time, and these fluctuations are increased suddenly and causing surge initiation. The major part which is responsible for the sudden increase in fluctuations is the vaneless region because it was found that the problem starts at the impeller exit near the shroud surface and then transfers to the impeller inlet. Results also showed that during surge, forces on the impeller blades increase to nearly double of its initial value and then decrease again. By using air injection at the vaneless region with different injection angles, it was found that injection with angle of 30° has a good effect on preventing surge and minimizing the pressure fluctuations comparing to other injection angles results. Results showed finally that the surge margin can be increased by using the injection with angle of 30° and with injection mass flow rate of 1% of the design inlet mass flow rate and this causes the surge limit to shift from 4 kg/s to 3.9 kg/s.

Backward Traveling Rotating Stall Waves in Centrifugal Compressors

2002 ◽  
Author(s):  
Z. S. Spakovsky
Keyword(s):  
Mass Flow ◽  
Centrifugal Compressor ◽  
First Principles ◽  
Rotating Stall ◽  
Air Injection ◽  
System Stability ◽  
Centrifugal Compressors ◽  
Injection Scheme ◽  
Surge Margin ◽  
Low Order

Rotating stall waves that travel against the direction of rotor rotation are reported for the first time and a new, low-order analytical approach to model centrifugal compressor stability is introduced. The model is capable of dealing with unsteady radially swirling flows and the dynamic effects of impeller-diffuser component interaction as it occurs in centrifugal compression systems. A simple coupling criterion is developed from first principles to explain the interaction mechanism important for system stability. The model findings together with experimental data explain the mechanism for first-ever observed backward traveling rotating stall in centrifugal compressors with vaned diffusers. Based on the low-order model predictions, an air injection scheme between the impeller and the vaned diffuser is designed for the NASA Glenn CC3 high-speed centrifugal compressor. The steady air injection experiments show an increase of 25% in surge-margin with an injection mass flow of 0.5% of the compressor mass flow. In addition, it is experimentally demonstrated that this injection scheme is robust to impeller tip-clearance effects and that a reduced number of injectors can be applied for similar gains in surge-margin. The results presented in this paper firmly establish the connection between the experimentally observed dynamic phenomena in the NASA CC3 centrifugal compressor and a first principles based coupling criterion. In addition, guidelines are given for the design of centrifugal compressors with enhanced stability.

Stall Warning Using the Rotor Tip Pressure in a Transonic Axial Compressor With Circumferential Grooves

2018 ◽  
Author(s):  
Byeung Jun Lim ◽  
Tae Choon Park ◽  
Young Seok Kang
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Axial Compressor ◽  
Rotating Stall ◽  
Single Stage ◽  
Stall Inception ◽  
Casing Treatment ◽  
Stall Warning ◽  
Transonic Axial Compressor

In this study, characteristics of stall inception in a single-stage transonic axial compressor with circumferential grooves casing treatment were investigated experimentally. Additionally, the characteristic of increasing irregularity in the pressure inside circumferential grooves as the compressor approaches the stall limit was applied to the stall warning method. Spike-type rotating stall was observed in the single-stage transonic axial compressor with smooth casing. When circumferential grooves were applied, the stall inception was suppressed and the operating point of the compressor moved to lower flow rate than the stall limit. A spike-like disturbance was developed into a rotating stall cell and then the Helmholtz perturbation was overlapped on it at N = 80%. At N = 70 %, the Helmholtz perturbation was observed first and the amplitude of the wave gradually increased as mass flow rate decreased. At N = 60%, spike type stall inceptions were observed intermittently and then developed into continuous rotating stall at lower mass flow rate. Pressure measured at the bottom of circumferential grooves showed that the level of irregularity of pressure increased as flow rate decreased. Based on the characteristic of increasing irregularity of the pressure signals inside the circumferential grooves as stall approaches, an autocorrelation technique was applied to the stall warning. This technique could be used to provide warning against stall and estimate real-time stall margins in compressors with casing treatments.

On the Dynamics of Compressor Surge

1976 ◽  
Vol 18 (5) ◽  
pp. 234-238 ◽  
Author(s):  
D. H. McQueen
Keyword(s):  
Mass Flow Rate ◽  
Limit Cycle ◽  
Mass Flow ◽  
Flow Rate ◽  
Pressure Head ◽  
Centrifugal Compressors ◽  
One Dimensional ◽  
Acoustical Properties ◽  
Compressor Surge ◽  
The One

The one-dimensional equations of surge in centrifugal compressors are solved graphically for the pressure head and mass flow rate as functions of time for a variety of situations, and the results are discussed in terms of the acoustical properties of the external piping. Two important parameters affecting the nature of the surge limit cycle are found to be simply related to the acoustic capacitance and acoustic inductance of the system.

Reduced-Order Modelling of Rotating Stall

2020 ◽  
Author(s):  
Dominik Schlüter ◽  
Robert P. Grewe ◽  
Fabian Wartzek ◽  
Alexander Liefke ◽  
Jan Werner ◽  
...  
Keyword(s):  
Single Cell ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Rotational Speed ◽  
Stability Limit ◽  
Rotating Stall ◽  
Operating Conditions ◽  
Transonic Compressor ◽  
Experimental Findings

Abstract Rotating stall is a non-axisymmetric disturbance in axial compressors arising at operating conditions beyond the stability limit of a stage. Although well-known, its driving mechanisms determining the number of stall cells and their rotational speed are still marginally understood. Numerical studies applying full-wheel 3D unsteady RANS calculations require weeks per operating point. This paper quantifies the capability of a more feasible quasi-2D approach to reproduce 3D rotating stall and related sensitivities. The first part of the paper deals with the validation of a numerical baseline the simplified model is compared to in detail. Therefore, 3D computations of a state-of-the-art transonic compressor are conducted. At steady conditions the single-passage RANS CFD matches the experimental results within an error of 1% in total pressure ratio and mass flow rate. At stalled conditions, the full-wheel URANS computation shows the same spiketype disturbance as the experiment. However, the CFD underpredicts the stalling point by approximately 7% in mass flow rate. In deep stall, the computational model correctly forecasts a single-cell rotating stall. The stall cell differs by approximately 21% in rotational speed and 18% in circumferential size from the experimental findings. As the 3D model reflects the compressor behaviour sufficiently accurate, it is considered valid for physical investigations. In the second part of the paper, the validated baseline is reduced in radial direction to a quasi-2D domain only resembling the compressor tip area. Four model variations regarding span-wise location and extent are numerically investigated. As the most promising model matches the 3D flow conditions in the rotor tip region, it correctly yields a single-cell rotating stall. The cell differs by only 7% in circumferential size from the 3D results. Due to the impeded radial migration in the quasi-2D slice, however, the cell exhibits an increased axial extent. It is assumed, that the axial expansion into the adjacent rows causes the difference in cell speed by approximately 24%. Further validation of the reduced model against experimental findings reveals, that it correctly reflects the sensitivity of circumferential cell size to flow coefficient and individual cell speed to compressor shaft speed. As the approach reduced the wall clock time by 92%, it can be used to increase the physical understanding of rotating stall at much lower costs.

Control of Self-Excited Oscillations in Centrifugal Blowers

2007 ◽  
Author(s):  
Saad A. Ahmed
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Critical Mass ◽  
Industrial Applications ◽  
Rotating Stall ◽  
Operating Conditions ◽  
Flow Coefficient ◽  
Flow Area ◽  
The Stability

Centrifugal compressors or blowers are widely used in many industrial applications. However, the operation of such systems is limited at low-mass flow rates by self-excited flow instabilities which could result in rotating stall or surge of the compressor. These instabilities will limit the flow range in which the compressor or the blower can operate, and will also lower their performance and efficiency. Experimental techniques were used to investigate a model of radial vaneless diffuser at stall and stall-free operating conditions. The speed of the impeller was kept constant, while the mass flow rate was reduced gradually to study the steady and unsteady operating conditions of the compressor. Additional experiments were made to investigate the effects of reducing the exit flow area on the inception of stall. The results indicate that the instability in the diffuser was successfully delayed to a lower flow coefficient when throttle rings were attached to either one or both of the diffuser walls (i.e., to reduce the diffuser exit flow area). The results also showed that an increase of the blockage ratio improves the stability of the system (i.e., the critical mass flow rate could be reduced to 50% of its value without blockage). The results indicate that the throttle rings could be an effective method to control stall in radial diffusers.

Numerical Simulation of Steady Air Injection Flow Control Effects on a Transonic Axial Flow Compressor

2012 ◽  
Vol 224 ◽  
pp. 352-357
Author(s):  
Islem Benhegouga ◽  
Ce Yang
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Leading Edge ◽  
Air Injection ◽  
Axial Flow Compressor ◽  
Blade Tip ◽  
Flow Compressor

In this work, steady air injection upstream of the blade leading edge was used in a transonic axial flow compressor, NASA rotor 37. The injectors were placed at 27 % upstream of the axial chord length at blade tip, the injection mass flow rate is 3% of the chock mass flow rate, and 3 yaw angles were used, respectively -20°, -30°, and -40°. Negative yaw angles were measured relative to the compressor face in opposite direction of rotational speeds. To reveal the mechanism, steady numerical simulations were performed using FINE/TURBO software package. The results show that the stall mass flow can be decreased about 2.5 %, and an increase in the total pressure ratio up to 0.5%.

Sign in / Sign up

Export Citation Format

Share Document