Effect of Heat Treatment on the Reactivity and Crystallinity of Coal-Char

2005 ◽  
Author(s):  
Shouyu Zhang ◽  
Junfu Lu ◽  
Jianmin Zhang ◽  
Qing Liu ◽  
Guangxi Yue
Keyword(s):  
Heat Treatment ◽  
Heat Treatment Temperature ◽  
Treatment Time ◽  
Treatment Temperature ◽  
Coal Char ◽  
Heat Treatment Time ◽  
Heat Treat ◽  
Heat Treated ◽  
Layer Stacking ◽  
Crystalline Growth

The effect of heat treatment on the reactivity and crystallinity of char prepared from the vitrinite of two coals (YX, JJ) was investigated by using XRD and TGA in this paper. The results from TGA show that the reactivity of the chars from YXV and JJV decreases with the increase of heat treatment temperature. The reactivity of YXV char decreases quickly and significantly as heat treatment time increases. However, after heat treatment time of 60 min, it decreases slowly. The effect of heat treatment time on the reactivity of JJV char is small. The results from XRD show that the crystallinity of coal-char is determined by the intensity of heat treatment. When heat treatment time is more than 60 minutes, the turbostratic crystallite of YXV char prepared under 900°C changes remarkably and becomes more orderly. The aromatic layer stacking heights (Lc) of YXV Char when heat treated above 900°C increased with the increase of heat treatment time. The effect of heat treat time on Lc of JJV char is small, but under heat treatment temperature of 1200°C, the crystalline of JJV char grows distinctly. There is a good parallel relationship between the crystalline growth and deactivation of the chars. It can be concluded that the growth of the crystalline is the main reason for the deactivation of coal-char.

Low-temperature thermal pretreatment process for recycling inner core of spent lithium iron phosphate batteries

2020 ◽  
pp. 0734242X2095740
Author(s):  
Haijun Bi ◽  
Huabing Zhu ◽  
Lei Zu ◽  
Yong Gao ◽  
Song Gao ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Low Temperature ◽  
Heat Treatment Temperature ◽  
Lithium Iron Phosphate ◽  
Inner Core ◽  
Treatment Time ◽  
Iron Phosphate ◽  
Treatment Temperature ◽  
Heat Treatment Time ◽  
Physicochemical Changes

Spent lithium iron phosphate (LFP) batteries contain abundant strategic lithium resources and are thus considered attractive secondary lithium sources. However, these batteries may contaminate the environment because they contain hazardous materials. In this work, a novel process involving low-temperature heat treatment is used as an alternative pretreatment method for recycling spent LFP batteries. When the temperature reaches 300°C, the dissociation effect of the anode material gradually improves with heat treatment time. At the heat treatment time of 120 minutes, an electrode material can be dissociated. The extension of heat treatment time has a minimal effect on quality loss. The physicochemical changes in thermally treated solid cathode and anode materials are examined through scanning electron microscopy with energy-dispersive X-ray spectroscopy. The heat treatment results in the complete separation of the materials from aluminium foil without contamination. The change in heat treatment temperature has a small effect on the quality of LFP material shedding. When the heat treatment temperature reaches 300°C and the time reaches 120 minutes, heat treatment time increases, and the yield of each particle size is stable and basically unchanged. The method can be scaled up and may reduce environmental pollution due to waste LFP batteries.

Load TiO2 or TiO2-N on the Porous Carbon

2012 ◽  
Vol 512-515 ◽  
pp. 1686-1689
Author(s):  
Jie Chen ◽  
Le Fu Mei ◽  
Li Bing Liao
Keyword(s):  
Heat Treatment ◽  
Porous Carbon ◽  
Heat Treatment Temperature ◽  
Treatment Time ◽  
Sol Gel ◽  
Treatment Temperature ◽  
Heat Treatment Time ◽  
Sem Images ◽  
Soaking Time ◽  
Sol Gel Process

In this paper, porous carbon has been used to carry TiO2 and TiO2-N by a sol-gel process. The effect of soaking time, heat treatment temperature, and heat treatment time on the carrying efficiency have been studied. XRD experiments indicated that TiO2 and TiO2-N crystallized in anatase and rutile with the ratio of 3∶2. SEM images showed that island-like TiO2 and TiO2-N particles with diameters in the range of 1-5um, the biggest size is about 10um, were evenly coated on the surface of the porous carbon.

Effect of Heat Treatment on Hardness of Electroless Ni-P Plating

2011 ◽  
Vol 228-229 ◽  
pp. 878-882
Author(s):  
Guan Jun Liu ◽  
Xin Hua Mao ◽  
Jun Cao ◽  
Zhou Yu
Keyword(s):  
Heat Treatment ◽  
Heat Treatment Temperature ◽  
Phosphorus Content ◽  
Treatment Time ◽  
Design Method ◽  
Uniform Design ◽  
Heat Treatment Condition ◽  
Treatment Temperature ◽  
Heat Treatment Time ◽  
Alloy Plating

Hardness of electronless Ni-P alloy plating which have five different phosphorus content were investigated with HX-1000 type microscopic Vickers hardness tester, respectively. Phosphorus content of Ni-P platings were investigated by Quanta 200 type scanning electron microscope and Oxford Energy Disperse Spectroscopy Heat treatment temperature and time of the different platings were optimized and analysed by Uniform Design method, respectively. The results show that correlation consist between maximum hardness of the Ni-P alloy plating and heat treatment temperature, not heat treatment time under the experimental condition which the heat treatment time is between one hour and five hours, and maximal value of the plating hardness appears when the heat treatment temperature is 400-430 Celsius degree. Maximal hardness value of the electronless Ni-P alloy plating increases with increase of their phosphorus content under heat treatment condition.

scholarly journals Effect of Processing Parameters on the Thermal and Electrical Properties of Electroless Nickel-Phosphorus Plated Carbon Fiber Heating Elements

2020 ◽  
Vol 6 (1) ◽  
pp. 6
Author(s):  
Bo-Kyung Choi ◽  
Soo-Jin Park ◽  
Min-Kang Seo
Keyword(s):  
Heat Treatment ◽  
Electrical Properties ◽  
Heat Treatment Temperature ◽  
Treatment Time ◽  
Volume Resistivity ◽  
Treatment Temperature ◽  
Heat Treatment Time ◽  
Plating Bath ◽  
Infrared Thermal Imaging ◽  
Thermal And Electrical Properties

Carbon fibers (CFs) were plated with nickel-phosphorus (Ni-P) using an electroless plating process. The effects of the process parameters such as heat treatment temperature, heat treatment time, and the pH of the plating bath on electroless Ni-P plating were investigated. The structure, elemental composition, and thermal and electrical properties of Ni-P plated CFs (MCF) were characterized by X-ray diffraction (XRD), a four-probe volume resistivity tester, and an infrared thermal imaging camera, respectively. The XRD indicated the presence of amorphous and crystalline phases of Ni and Ni-P. The MCF were able to perform at high temperatures because of their higher thermal conductivity. A heat treatment temperature of 300 °C, a heat treatment time of 4 h, and a pH of 8.5 were found to be optimum for obtaining MCF with desirable thermal and electrical properties.

Study on the Crimp Property of PTT/PET Bicomponent Filament

2013 ◽  
Vol 781-784 ◽  
pp. 2680-2684
Author(s):  
Kan Lai ◽  
Mei Yu Chen ◽  
Run Jun Sun ◽  
Hong Sun
Keyword(s):  
Heat Treatment ◽  
Water Treatment ◽  
Heat Treatment Temperature ◽  
Treatment Time ◽  
Heat Treatments ◽  
Treatment Temperature ◽  
Heat Treatment Time ◽  
Boiling Water ◽  
Component Ratio

In this work, the crimp properties of PTT/PET bicomponent filament with different component ratios were investigated. The results show that, after boiling water treatment for 15 minutes, the crimpability of 50/50 component ratio is superior to that of 40/60 and 60/40 component ratio. Heat treatment can realize the shrinkage difference of the two components in a biocomponent filament and enable the biocomponent filament to have good crimpability and bulkiness. In addition, different heat treatments, heat treatment time and heat treatment temperature can also bring different crimp effects to the biocomponent filaments.

scholarly journals Water Resistance and Creep Behavior of Heat-Treated Moso Bamboo Determined by the Stepped Isostress Method

Polymers ◽  
2021 ◽  
Vol 13 (8) ◽  
pp. 1264
Author(s):  
Teng-Chun Yang ◽  
Tung-Lin Wu ◽  
Chin-Hao Yeh
Keyword(s):  
Heat Treatment ◽  
Water Absorption ◽  
Creep Behavior ◽  
Heat Treatment Temperature ◽  
Water Resistance ◽  
Absorption Efficiency ◽  
Treatment Temperature ◽  
Moso Bamboo ◽  
Phyllostachys Pubescens ◽  
Heat Treated

The influence of heat treatment on the physico-mechanical properties, water resistance, and creep behavior of moso bamboo (Phyllostachys pubescens) was determined in this study. The results revealed that the density, moisture content, and flexural properties showed negative relationships with the heat treatment temperature, while an improvement in the dimensional stability (anti-swelling efficiency and anti-water absorption efficiency) of heat-treated samples was observed during water absorption tests. Additionally, the creep master curves of the untreated and heat-treated samples were successfully constructed using the stepped isostress method (SSM) at a series of elevated stresses. Furthermore, the SSM-predicted creep compliance curves fit well with the 90-day full-scale experimental data. When the heat treatment temperature increased to 180 °C, the degradation ratio of the creep resistance (rd) significantly increased over all periods. However, the rd of the tested bamboo decreased as the heat treatment temperature increased up to 220 °C.

Effect of Heat Treatment on the Microstructure and Property of TiAl Alloys Prepared by Gas Atomization Powders

2013 ◽  
Vol 747-748 ◽  
pp. 497-501
Author(s):  
Na Liu ◽  
Zhou Li ◽  
Guo Qing Zhang ◽  
Hua Yuan ◽  
Wen Yong Xu ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Heat Treatment Temperature ◽  
Tial Alloy ◽  
Lamellar Microstructure ◽  
Treatment Temperature ◽  
Gas Atomization ◽  
Thermally Induced ◽  
Heat Treated ◽  
Fine Duplex ◽  
Step Heat Treatment

Powder metallurgical TiAl alloy was fabricated by gas atomization powders, and the effect of heat treatment temperature on the microstructure evolution and room tensile properties of PM TiAl alloy was investigated. The uniform fine duplex microstructure was formed in PM TiAl based alloy after being heat treated at 1250/2h followed by furnace cooling (FC)+ 900/6h (FC). When the first step heat treatment temperature was improved to 1360/1h, the near lamellar microstructure was achieved. The ductility of the alloy after heat treatment improved markedly to 1.2% and 0.6%, but the tensile strength decreased to 570MPa and 600MPa compared to 655MPa of as-HIP TiAl alloy. Post heat treatment at the higher temperature in the alpha plus gamma field would regenerate thermally induced porosity (TIP).

Mechanical and Superelastic Properties of Au-51Ti-18Co Biomedical Shape Memory Alloy Heat-Treated at 1173 K to 1373 K

2016 ◽  
Vol 97 ◽  
pp. 141-146 ◽  
Author(s):  
Taywin Buasri ◽  
Hyunbo Shim ◽  
Masaki Tahara ◽  
Tomonari Inamura ◽  
Kenji Goto ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Heat Treatment Temperature ◽  
Critical Stress ◽  
Biomedical Applications ◽  
Shape Recovery ◽  
Treatment Temperature ◽  
Recovery Ratio ◽  
Recovery Strain ◽  
Heat Treated ◽  
Alloy Heat

The effect of heat treatment temperature from 1173 K to 1373 K for 3.6 ks on mechanical and superelastic properties of an Ni-free Au-51Ti-18Co alloy (mol%) was investigated. The stress for inducing martensitic transformation (SIMT) and the critical stress for slip deformation (CSS) slightly decrease with increasing the heat–treatment temperature. Regardless of heat–treatment temperature, good superelasticity was definitely recognized with the maximum shape recovery ratio up to 95 % and 4 % superelastic shape recovery strain. As the mentioned reasons, the Au-51Ti-18Co alloy is promising for practical biomedical applications.

Investigation of Heat Treated Electrodeposited CoNiFe on Microstructure and Hardness

2015 ◽  
Vol 1113 ◽  
pp. 56-61
Author(s):  
Nor Azrina Resali ◽  
Koay Mei Hyie ◽  
M.N. Berhan ◽  
C.M. Mardziah
Keyword(s):  
Heat Treatment ◽  
Heat Treatment Temperature ◽  
Treatment Temperature ◽  
Crystallographic Structure ◽  
Face Centered Cubic ◽  
Heat Treated ◽  
Hardness Property ◽  
Finishing Process ◽  
The Face ◽  
Face Centered

In this research, heat treatment is the final finishing process applied on nanocrystalline CoNiFe to improve microstructure for good hardness property. Nanocrystalline CoNiFe has been synthesized using the electrodeposition method. This study investigated the effect of heat treatment at 500°C, 600°C, 700°C and 800°C on electrodeposited nanocrystalline CoNiFe. The heat treatment process was performed in the tube furnace with flowing Argon gas. By changing the heat treatment temperature, physical properties such as phase and crystallographic structure, surface morphology, grain size and hardness of nanocrystalline CoNiFe was studied. The nanocrystalline CoNiFe phase revealed the Face Centered Cubic (FCC) and Body Centered Cubic (BCC) crystal structure. FESEM micrographs showed that the grain sizes of the coatings were in the range of 78.76 nm to 132 nm. Dendrite shape was found in the microstructure of nanocrystalline CoNiFe. The nanocrystalline CoNiFe prepared in heat treatment temperature of 700°C, achieved the highest hardness of 449 HVN. The surface roughness of nanocrystalline CoNiFe heated at 700°C was found to be smaller than other temperatures.

Sign in / Sign up

Export Citation Format

Share Document