Gas Properties as a Limit to Gas Turbine Performance

2002 ◽  
Author(s):  
R. C. Wilcock ◽  
J. B. Young ◽  
J. H. Horlock
Keyword(s):  
Gas Turbines ◽  
Industrial Development ◽  
Pressure Ratio ◽  
Cycle Performance ◽  
Working Fluid ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Turbine Inlet ◽  
Cycle Efficiency ◽  
Gas Properties

Although increasing the turbine inlet temperature has traditionally proved the surest way to increase cycle efficiency, recent work suggests that the performance of future gas turbines may be limited by increased cooling flows and losses. Another limiting scenario concerns the effect on cycle performance of real gas properties at high temperatures. Cycle calculations of uncooled gas turbines show that when gas properties are modelled accurately, the variation of cycle efficiency with turbine inlet temperature at constant pressure ratio exhibits a maximum at temperatures well below the stoichiometric limit. Furthermore, the temperature at the maximum decreases with increasing compressor and turbine polytropic efficiency. This behaviour is examined in the context of a two-component model of the working fluid. The dominant influences come from the change of composition of the combustion products with varying air/fuel ratio (particularly the contribution from the water vapour) together with the temperature variation of the specific heat capacity of air. There are implications for future industrial development programmes, particularly in the context of advanced mixed gas-steam cycles.

Approximate Relations for Optimum Turbine Operating Parameters in Allam Cycle

2020 ◽  
Author(s):  
Yousef Haseli
Keyword(s):  
Turbine Blades ◽  
Air Separation ◽  
Cycle Performance ◽  
Working Fluid ◽  
Operating Parameters ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Power Cycle ◽  
Turbine Inlet ◽  
Cycle Efficiency

Abstract The Allam power cycle is a novel method for clean power generation which employs the concept of oxyfuel combustion with carbon dioxide as the main working fluid. To date, only a few studies have appeared in the literature in that the performance of the Allam cycle has been assessed using a commercial software. The objective of this article is to explore relations between the cycle performance and the main operating parameters of the Allam cycle through a simplified thermodynamic analysis and mathematical modeling. The cycle efficiency is maximized with respect to turbine parameters. Expressions are derived for estimation of optimum turbine inlet temperature and pressure as well as optimum turbine exhaust pressure. Main simplifications include no portion of the recycled CO2 is used for turbine blades cooling and single stage CO2 compressor without intercooling. The cryogenic air separation process developed by Allam is employed which produces supercritical oxygen at combustion pressure. Typical numerical results are presented using the new expressions for optimum turbine parameters. The highest cycle efficiency is found to be 66.4% at a turbine inlet temperature/inlet pressure/exhaust pressure of 1306 K/300 bar/39.4 bar and a CO2 compressor exit pressure of 60 bar. The newly derived relationships among the key process parameters allow a better understanding of the operation of Allam cycle.

scholarly journals Evaluation of Bleed Flow Precooling Influence on the Efficiency of the E-MATIANT Cycle

2020 ◽  
Vol 22 (2) ◽  
pp. 593-602 ◽  
Author(s):  
Andrey Rogalev ◽  
Vladimir Kindra ◽  
Alexey Zonov ◽  
Nikolay Rogalev ◽  
Levon Agamirov
Keyword(s):  
Gas Turbines ◽  
Pressure Ratio ◽  
Water Injection ◽  
Design Parameters ◽  
Inlet Temperature ◽  
Combustion Chambers ◽  
Turbine Inlet ◽  
Performance Penalty ◽  
Set Up ◽  
Cycle Efficiency

AbstractThis study aims to present a method for precooling bleed flow by water injection in the E-MATIANT cycle and to estimate its impact on the overall efficiency. The design parameters of the cycle are set up on the basis of the component technologies of today's state-of-the-art gas turbines with a turbine inlet temperature between 1100 and 1700°C. Several schemes of the E-MATIANT cycle are considered: with one, two and three combustion chambers. The optimal pressure ratio ranges for the considered turbine inlet temperatures are identified and a comparison with existing evaluations is made. For the optimal initial parameters, cycle net efficiency varies from 42.0 to 49.8%. A significant influence of turbine stage cooling model on optimal thermodynamic parameters and cycle efficiency is established. The maximum cycle efficiency is 44.0% considering cooling losses. The performance penalty due to the oxygen production and carbon dioxide capture is 20–22%.

Evaluation of Design Performance of the Semi-Closed Oxy-Fuel Combustion Combined Cycle

2012 ◽  
Author(s):  
H. J. Yang ◽  
D. W. Kang ◽  
J. H. Ahn ◽  
T. S. Kim
Keyword(s):  
Co2 Capture ◽  
Gas Turbines ◽  
Fuel Combustion ◽  
Combined Cycle ◽  
Cycle Performance ◽  
Design Parameters ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Separation Unit ◽  
Turbine Inlet

This study aims to present various design aspects and realizable performance of the natural gas fired semi-closed oxy-fuel combustion combined cycle (SCOC-CC). Design parameters of the cycle are set up on the basis of component technologies of today’s state-of-the-art gas turbines with a turbine inlet temperature between 1400°C and 1600°C. The most important part in the cycle analysis is the turbine cooling which affects the cycle performance considerably. A thermodynamic cooling model is introduced to predict the reasonable amount of turbine coolant to maintain the turbine blade temperature of the SCOC-CC at the levels of those of conventional gas turbines. Optimal pressure ratio ranges of the SCOC-CC for two different turbine inlet temperature levels are searched. The performance penalty due to the CO2 capture is examined. Also investigated are the influences of the purity of oxygen provided by the air separation unit on the cycle performance. A comparison with the conventional combined cycle adopting a post-combustion CO2 capture is carried out taking into account the relationship between performance and CO2 capture rate.

Performance of N2O4 Gas Cycles for Solar Power Applications

1979 ◽  
Vol 193 (1) ◽  
pp. 313-320 ◽  
Author(s):  
G. Angelino
Keyword(s):  
Waste Heat ◽  
Working Fluid ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Power Cycles ◽  
Average Temperature ◽  
Power Stations ◽  
Turbine Inlet ◽  
Compressor Inlet ◽  
Cycle Efficiency

The use of N2O4 as the working fluid in gas turbine power cycles is recognized as a potential instrument for improving cycle efficiency at moderate top temperatures while maintaining the technical advantages connected with the waste heat rejection at a comparatively high average temperature. Solar central receiver power stations, whose economic effectiveness is very sensitive to cycle efficiency and which must often reject their waste heat into the atmosphere, could usefully adopt this fluid. The thermodynamic reasons which explain the peculiar behaviour of N2O4 as the Brayton cycle working fluid are discussed. With respect to inert gas cycles, N2O4 permits, for a given efficiency, a reduction in turbine inlet temperature by 200-250°C. At a given turbine inlet temperature, the dissociating character of N2O4 allows overall efficiencies similar to those of steam cycles (at least for moderate plant capacities and provided N2O4 and steam cycles reject their waste heat at comparable temperatures). The relatively long relaxation time of the second step of the N2O4 dissociation can represent a problem mainly for the regenerator. A cycle is presented where regeneration at a pressure higher than the compressor inlet pressure can alleviate this problem.

Evaluation of Design Performance of the Semi-Closed Oxy-Fuel Combustion Combined Cycle

2012 ◽  
Vol 134 (11) ◽  
Author(s):  
H. J. Yang ◽  
D. W. Kang ◽  
J. H. Ahn ◽  
T. S. Kim
Keyword(s):  
Co2 Capture ◽  
Gas Turbines ◽  
Fuel Combustion ◽  
Combined Cycle ◽  
Cycle Performance ◽  
Design Parameters ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Separation Unit ◽  
Turbine Inlet

This study aims to present various design aspects and realizable performance of the natural gas fired semi-closed oxy-fuel combustion combined cycle (SCOC-CC). The design parameters of the cycle are set up on the basis of the component technologies of today’s state-of-the-art gas turbines with a turbine inlet temperature between 1400 °C and 1600 °C. The most important part of the cycle analysis is the turbine cooling, which considerably affects the cycle performance. A thermodynamic cooling model is introduced in order to predict the reasonable amount of turbine coolant needed to maintain the turbine blade temperature of the SCOC-CC at the levels of those of conventional gas turbines. The optimal pressure ratio ranges of the SCOC-CC for two different turbine inlet temperature levels are researched. The performance penalty due to the CO2 capture is examined. The influences of the purity of the oxygen provided by the air separation unit on the cycle performance are also investigated. A comparison with the conventional combined cycle, adopting a postcombustion CO2 capture, is carried out, taking into account the relationship between the performance and the CO2 capture rate.

Influence of Turbine Inlet Temperature on the Efficiency of Externally Fired Gas Turbines

2014 ◽  
pp. 79-95 ◽  
Author(s):  
Paulo Eduardo Batista de Mello ◽  
Sérgio Scuotto ◽  
Fernando dos Santos Ortega ◽  
Gustavo Henrique Bolognesi Donato
Keyword(s):  
Gas Turbines ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Turbine Inlet

Expanding Fuel Flexibility in MHPS’ Dry Low NOx Combustor

2018 ◽  
Author(s):  
Katsuyoshi Tada ◽  
Kei Inoue ◽  
Tomo Kawakami ◽  
Keijiro Saitoh ◽  
Satoshi Tanimura
Keyword(s):  
Power Systems ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Environmental Conservation ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Social Perspectives ◽  
Turbine Inlet ◽  
Fuel Flexibility

Gas-turbine combined-cycle (GTCC) power generation is clean and efficient, and its demand will increase in the future from economic and social perspectives. Raising turbine inlet temperature is an effective way to increase combined cycle efficiency and contributes to global environmental conservation by reducing CO2 emissions and preventing global warming. However, increasing turbine inlet temperature can lead to the increase of NOx emissions, depletion of the ozone layer and generation of photochemical smog. To deal with this issue, MHPS (MITSUBISHI HITACHI POWER SYSTEMS) and MHI (MITSUBISHI HEAVY INDUSTRIES) have developed Dry Low NOx (DLN) combustion techniques for high temperature gas turbines. In addition, fuel flexibility is one of the most important features for DLN combustors to meet the requirement of the gas turbine market. MHPS and MHI have demonstrated DLN combustor fuel flexibility with natural gas (NG) fuels that have a large Wobbe Index variation, a Hydrogen-NG mixture, and crude oils.

Proposal of Innovative Gas Turbine Combined Cycle Power Generation System

2004 ◽  
Author(s):  
Hideto Moritsuka
Keyword(s):  
Power Generation ◽  
Gas Turbine ◽  
Thermal Efficiency ◽  
Pressure Ratio ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Generation System ◽  
Turbine Inlet Temperature ◽  
Turbine Inlet ◽  
Power Generation System

In order to estimate the possibility to improve thermal efficiency of power generation use gas turbine combined cycle power generation system, benefits of employing the advanced gas turbine technologies proposed here have been made clear based on the recently developed 1500C-class steam cooling gas turbine and 1300C-class reheat cycle gas turbine combined cycle power generation systems. In addition, methane reforming cooling method and NO reducing catalytic reheater are proposed. Based on these findings, the Maximized efficiency Optimized Reheat cycle Innovative Gas Turbine Combined cycle (MORITC) Power Generation System with the most effective combination of advanced technologies and the new devices have been proposed. In case of the proposed reheat cycle gas turbine with pressure ratio being 55, the high pressure turbine inlet temperature being 1700C, the low pressure turbine inlet temperature being 800C, combined with the ultra super critical pressure, double reheat type heat recovery Rankine cycle, the thermal efficiency of combined cycle are expected approximately 66.7% (LHV, generator end).

scholarly journals Thermal Performance Analysis of a Direct-Heated Recompression Supercritical Carbon Dioxide Brayton Cycle Using Solar Concentrators

Energies ◽  
2019 ◽  
Vol 12 (22) ◽  
pp. 4358 ◽  
Author(s):  
Jinping Wang ◽  
Jun Wang ◽  
Peter D. Lund ◽  
Hongxia Zhu
Keyword(s):  
Incidence Angle ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
Brayton Cycle ◽  
Turbine Inlet Temperature ◽  
Beam Radiation ◽  
Solar Concentrators ◽  
Cooling Temperature ◽  
Turbine Inlet ◽  
Cycle Efficiency

In this study, a direct recompression supercritical CO2 Brayton cycle, using parabolic trough solar concentrators (PTC), is developed and analyzed employing a new simulation model. The effects of variations in operating conditions and parameters on the performance of the s-CO2 Brayton cycle are investigated, also under varying weather conditions. The results indicate that the efficiency of the s-CO2 Brayton cycle is mainly affected by the compressor outlet pressure, turbine inlet temperature and cooling temperature: Increasing the turbine inlet pressure reduces the efficiency of the cycle and also requires changing the split fraction, where increasing the turbine inlet temperature increases the efficiency, but has a very small effect on the split fraction. At the critical cooling temperature point (31.25 °C), the cycle efficiency reaches a maximum value of 0.4, but drops after this point. In optimal conditions, a cycle efficiency well above 0.4 is possible. The maximum system efficiency with the PTCs remains slightly below this value as the performance of the whole system is also affected by the solar tracking method used, the season and the incidence angle of the solar beam radiation which directly affects the efficiency of the concentrator. The choice of the tracking mode causes major temporal variations in the output of the cycle, which emphasis the role of an integrated TES with the s-CO2 Brayton cycle to provide dispatchable power.

Advanced High Temperature Gas-Cooled Reactor Systems

2008 ◽  
Author(s):  
Yasuyoshi Kato
Keyword(s):  
Gas Turbine ◽  
Power Conversion ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Co2 Gas ◽  
Flow Channels ◽  
Turbine Inlet ◽  
Conversion System ◽  
Gas Turbine Cycle ◽  
Cycle Efficiency

Three systems have been proposed for advanced high temperature gas-cooled reactors (HTGRs): a supercritical carbon dioxide (S-CO2) gas turbine power conversion system; a new MicroChannel Heat Exchanger (MCHE); and a once-through-then-out (OTTO) refueling scheme with burnable poison (BP) loading. An S-CO2 gas turbine cycle attains higher cycle efficiency than a He gas turbine cycle due to reduced compression work around the critical point of CO2. Considering temperature lowering at the turbine inlet by 30°C through the intermediate heat exchange, the S-CO2 indirect cycle achieves efficiency of 53.8% at turbine inlet temperature of 820°C and turbine inlet pressure of 20 MPa. This cycle efficiency value is higher by 4.5% than that (49.3%) of a He direct cycle at turbine inlet temperature of 850°C and 7 MPa. A new MCHE has been proposed as intermediate heat exchangers between the primary cooling He loop and the secondary S-CO2 gas turbine power conversion system; and recuperators of the S-CO2 gas turbine power conversion system. This MCHE has discontinuous “S”-shape fins providing flow channels with near sine curves. Its pressure drop is one-sixth reference to the conventional MCHE with zigzag flow channel configuration while the same high heat transfer performance inherits. The pressure drop reduction is ascribed to suppression of recirculation flows and eddies that appears around bend corners of zigzag flow channels in the conventional MCHE. An optimal BP loading in an OTTO refueling scheme eliminates the drawback of its excessively high axial power peaking factor, reducing the power peaking factor from 4.44 to about 1.7; and inheriting advantages over the multi-pass scheme because of the lack of fuel handling and integrity checking systems; and reloading. Because of the power peaking factor reduction, the maximum fuel temperatures are lower than the maximum permissible values of 1250°C for normal operation and 1600°C during a depressurization accident.

Sign in / Sign up

Export Citation Format

Share Document