The Impact of Forward Swept Rotors on Tip-Limited Low-Speed Axial Compressors

2003 ◽  
Author(s):  
G. Scott McNulty ◽  
John J. Decker ◽  
Brent F. Beacher ◽  
S. Arif Khalid
Keyword(s):  
Pressure Ratio ◽  
Pressure Coefficient ◽  
Aircraft Engine ◽  
Tip Clearance ◽  
Flow Measurements ◽  
Stall Margin ◽  
Tip Clearance Flow ◽  
Low Speed ◽  
Axial Compressors ◽  
The Impact

This paper presents an experimental and analytical study of the impact of forward swept rotors on tip-limited, low-speed, multi-stage axial compressors. Two different configurations were examined, one with strong tip-clearance flows and the other with more moderate levels. Evaluations were done at multiple rotor tip clearance levels to assess differences in clearance sensitivity. Both configurations are low-speed models of the rear stages of modern aircraft engine high pressure ratio compressors. Compared to conventionally stacked (radial) rotors, the forward swept blades demonstrated improvements in stall margin, efficiency and clearance sensitivity. The benefits were more pronounced for the configuration with stronger tip-clearance flows. Detailed flow measurements and 3-D viscous CFD analyses are used to investigate the responsible flow mechanisms. Forward sweep causes a spanwise redistribution of flow toward the blade tip and reduces the tip loading in terms of static pressure coefficient. This results in reduced tip-clearance flow blockage, a shallower (more axial) leakage/freestream interface angle and a smaller region of reversed flow in the clearance gap.

The Impact of Forward Swept Rotors on Tip Clearance Flows in Subsonic Axial Compressors

2004 ◽  
Vol 126 (4) ◽  
pp. 445-454 ◽  
Author(s):  
G. Scott McNulty ◽  
John J. Decker ◽  
Brent F. Beacher ◽  
S. Arif Khalid
Keyword(s):  
Pressure Coefficient ◽  
Three Dimensional ◽  
Tip Clearance ◽  
Flow Measurements ◽  
Stall Margin ◽  
Tip Clearance Flow ◽  
Axial Compressors ◽  
Flow Mechanisms ◽  
Cfd Analyses ◽  
The Impact

This paper presents an experimental and analytical study of the impact of forward swept rotors on tip-limited, low-speed, multistage axial compressors. Two different configurations were examined, one with strong tip-clearance flows and the other with more moderate levels. Evaluations were done at multiple rotor tip clearances to assess differences in clearance sensitivity. Compared to conventionally stacked radial rotors, the forward swept blades demonstrated improvements in stall margin, efficiency and clearance sensitivity. The benefits were more pronounced for the configuration with stronger tip-clearance flows. Detailed flow measurements and three-dimensional viscous CFD analyses were used to investigate the responsible flow mechanisms. Forward sweep causes a spanwise redistribution of flow toward the blade tip and reduces the tip loading in terms of static pressure coefficient. This results in reduced tip-clearance flow blockage, a shallower (more axial) vortex trajectory and a smaller region of reversed flow in the clearance gap.

The Effect of Tip Clearance on the Performance of Contra-Rotating Compressor

2012 ◽  
Author(s):  
Limin Gao ◽  
Xiaojun Li ◽  
Xudong Feng ◽  
Bo Liu
Keyword(s):  
Pressure Ratio ◽  
Weight Ratio ◽  
Aircraft Engine ◽  
Back Pressure ◽  
Tip Clearance ◽  
Stall Margin ◽  
Operating Range ◽  
Important Approach ◽  
The Impact ◽  
Wide Operating

Contra-rotating technology has been considered as an important approach to further improve the thrust-weight ratio of aircraft engine because of its structure and aerodynamic superiority. In the present work, the impact of tip clearance on the performance of a CRAC which consist of two counter-rotating rotors is investigated numerically. To detect the stall margin of CRAC exactly, the back pressure dichotomy method is developed, the grid indepence is verified and the performance is measured. A large number computation is carried out to explore the influence of tip clearance on the operating range of contra-rotating compressor. Finally the flow filed near the tip clearance is analyzed to find the relation between the tip clearance and the first stall rotor. The result shows: (1) Efficiency and pressure ratio decrease with the tip clearance size increased, but there is an optimal tip clearance size corresponding to a relative wide operating range. (2) The first stall stage of contra-rotating compressor varies with the tip clearance size increases. For the present CRAC, ROT2 is the first stall stage with the tip clearance size no greater than 0.5mm, while the ROT1 is the first stall stage if the tip clearance size greater than 0.5mm.

Influence of axial skewed slots on the rotating instability of a low-speed axial compressor

2020 ◽  
pp. 095441002094433
Author(s):  
Tao Li ◽  
Yadong Wu ◽  
Hua Ouyang
Keyword(s):  
Pressure Fluctuations ◽  
Flow Characteristics ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Frequency Spectra ◽  
Stall Margin ◽  
Tip Clearance Flow ◽  
Low Speed ◽  
Casing Treatment ◽  
Rotating Instability

Experimental and numerical analyses were performed on a low-speed axial compressor rotor to investigate the aerodynamic and acoustic effects of axial skewed slots casing treatment on the rotating instability. The experimental results showed that the stall margin could be improved by 8.0% and the frequency broadband hump owing to the rotating instability was suppressed effectively. In the noise spectra, the two dominant broadband humps on both sides of the blade-passing frequency also reduced in amplitude. Full-annulus unsteady computational fluid dynamics simulations were performed near the design condition. Time- and frequency-domain analyses as well as a proper orthogonal decomposition method were applied to obtain the oscillation, frequency, energy and flow characteristics of the rotating instability. Axial skewed slots casing treatment causes a distinct reduction in the amplitude of the pressure fluctuations and frequency spectra with a decrease in the energy of the rotating instability modes. The slots alleviated the tip flow blockage by the periodic injection and removal of the fluid from the passage, which enabled a high tip clearance flow downstream with little impingement on the neighbouring blade tip.

scholarly journals Design and Development of a Nine Stage Axial Flow Compressor for Industrial Gas Turbines

1998 ◽  
Author(s):  
G. D. Stringham ◽  
B. N. Cassem ◽  
T. C. Prince ◽  
P. F. Yeung
Keyword(s):  
Gas Turbines ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Leading Edge ◽  
Aircraft Engine ◽  
Modern Technology ◽  
Stall Margin ◽  
Axial Flow Compressor ◽  
Flow Compressor ◽  
The Impact

A nine stage industrial axial flow compressor with a pressure ratio of 9.1:1 was designed, built and rig tested. The modern technology and design tools developed by government/aircraft engine compressor technologists were used for an industrial gas turbine application. The compressor was designed with “arbitrary” airfoil blading including CFD analysis in all blade rows. Flowpath contouring in the hub region of the rotors was used to decrease losses. The compressor rig was tested at the Compressor Research Facility at Wright Patterson Air Force Base in Dayton, Ohio. Extensive testing included determining the impact of stator leading edge instrumentation on performance. The compressor demonstrated excellent efficiency and stall margin in its first build. This paper describes the aerodynamic design, test instrumentation and test results.

The Impact of Casing Groove Location on Stall Margin and Tip Clearance Flow in a Low-Speed Axial Compressor

2016 ◽  
Vol 138 (12) ◽  
Author(s):  
Du Juan ◽  
Li Jichao ◽  
Gao Lipeng ◽  
Lin Feng ◽  
Chen Jingyi
Keyword(s):  
Axial Compressor ◽  
Leading Edge ◽  
Suction Side ◽  
Tip Clearance ◽  
Tip Leakage Flow ◽  
Stall Inception ◽  
Stall Margin ◽  
Tip Clearance Flow ◽  
Clearance Flow ◽  
The Impact

In this study, the impact of single grooves at different locations on compressor stability and tip clearance flow are numerically and experimentally investigated. Initially, the numerical stall margin improvement (SMI) curve is examined using experimental data. Then, the evolution of the interface between the tip leakage flow (TLF) and the incoming main flow (MF) in the prestall and stall inception processes for two typical grooves, i.e., the worst and the optimal grooves in terms of their SMI, are compared with the smooth casing. The results show two different interface behaviors throughout the throttling process. The compressor with the worst single groove casing first experiences a long-length-scale disturbance after the interface near the blade suction side spills in front of the rotor leading-edge plane, and then goes through spikes after the whole interface spills. With the smooth casing and the optimal single groove near midchord, the interface reaches the rotor leading edge at the last stable operating point and spikes appear once the whole interface spills over the rotor leading edge. A model that illustrates the spillage patterns of the interface for the two stall precursors is thus proposed accordingly and used to explain their effectiveness in terms of the SMI. At last, the relevance of these results to the preliminary selection of groove locations for multigroove casing treatments (CTs) is verified by test data and discussed.

Endwall Blockage in Axial Compressors

1999 ◽  
Vol 121 (3) ◽  
pp. 499-509 ◽  
Author(s):  
S. A. Khalid ◽  
A. S. Khalsa ◽  
I. A. Waitz ◽  
C. S. Tan ◽  
E. M. Greitzer ◽  
...  
Keyword(s):  
Tip Clearance ◽  
Design Parameters ◽  
Tip Clearance Flow ◽  
Axial Compressors ◽  
Clearance Flow ◽  
Flow Features ◽  
Physical Insight ◽  
Level Loading ◽  
Stagger Angle ◽  
Insight Into

This paper presents a new methodology for quantifying compressor endwall blockage and an approach, using this quantification, for defining the links between design parameters, flow conditions, and the growth of blockage due to tip clearance flow. Numerical simulations, measurements in a low-speed compressor, and measurements in a wind tunnel designed to simulate a compressor clearance flow are used to assess the approach. The analysis thus developed allows predictions of endwall blockage associated with variations in tip clearance, blade stagger angle, inlet boundary layer thickness, loading level, loading profile, solidity, and clearance jet total pressure. The estimates provided by this simplified method capture the trends in blockage with changes in design parameters to within 10 percent. More importantly, however, the method provides physical insight into, and thus guidance for control of, the flow features and phenomena responsible for compressor endwall blockage generation.

Numerical Investigation of a Cantilevered Compressor Stator at Varying Clearance Sizes

2015 ◽  
Author(s):  
Chengwu Yang ◽  
Xingen Lu ◽  
Yanfeng Zhang ◽  
Shengfeng Zhao ◽  
Junqiang Zhu
Keyword(s):  
Flow Field ◽  
Axial Compressor ◽  
High Flow ◽  
Leakage Flow ◽  
Streamwise Direction ◽  
Stall Margin ◽  
Axial Compressors ◽  
Pressure Surface ◽  
The Impact ◽  
Highly Loaded

The clearance size of cantilevered stators affects the performance and stability of axial compressors significantly. Numerical calculations were carried out using the commercial software FINE/Turbo for a 2.5-stage highly loaded transonic axial compressor, which is of cantilevered stator for the first stage, at varying hub clearance sizes. The aim of this work is to improve understanding of the impact mechanism of hub clearance on the performance and the flow field in high flow turning conditions. The performance of the front stage and the compressor with different hub clearance sizes of the first stator has been analyzed firstly. Results show that the efficiency decreases as clearance size varies from 0 to 3% of hub chordlength, but the operating range has been extended. For the first stage, the efficiency decreases about 0.5% and the stall margin is extended. The following analysis of detailed flow field in the first stator shows that the clearance leakage flow and elimination of hub corner separation is responsible for the increasing loss and stall margin extending respectively. The effects of hub clearance on the downstream rotor have been discussed lastly. It indicates that the loss of the rotor increases and the flow deteriorates due to increasing of clearance size and hence the leakage mass flow rate, which mainly results from the interaction of upstream leakage flow with the passage flow near pressure surface. The affected region of rotor passage flow field expands in spanwise and streamwise direction as clearance size grows. The hub clearance leakage flow moves upward in span as it flows toward downstream.

Experimental and Numerical Investigation of a Circumferential Groove Casing Treatment in a Low Speed Axial Research Compressor at Different Tip Clearances

2017 ◽  
Author(s):  
Matthias Rolfes ◽  
Martin Lange ◽  
Konrad Vogeler ◽  
Ronald Mailach
Keyword(s):  
Total Pressure ◽  
Solid Wall ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Chord Length ◽  
Single Stage ◽  
Tip Clearance ◽  
Low Speed ◽  
Operating Range ◽  
Circumferential Groove

The demand of increasing pressure ratios for modern high pressure compressors leads to decreasing blade heights in the last stages. As tip clearances cannot be reduced to any amount and minimum values might be necessary for safety reasons, the tip clearance ratios of the last stages can reach values notably higher than current norms. This can be intensified by a compressor running in transient operations where thermal differences can lead to further growing clearances. For decades, the detrimental effects of large clearances on an axial compressor’s operating range and efficiency are known and investigated. The ability of circumferential casing grooves in the rotor casing to improve the compressor’s operating range has also been in the focus of research for many years. Their simplicity and ease of installation are one reason for their continuing popularity nowadays, where advanced methods to increase the operating range of an axial compressor are known. In a previous paper [1], three different circumferential groove casing treatments were investigated in a single stage environment in the Low Speed Axial Research Compressor at TU Dresden. One of these grooves was able to notably improve the operating range and the efficiency of the single stage compressor at very large rotor tip clearances (5% of chord length). In this paper, the results of tests with this particular groove type in a three stage environment in the Low Speed Axial Research Compressor are presented. Two different rotor tip clearance sizes of 1.2% and 5% of tip chord length were investigated. At the small tip clearance, the grooves are almost neutral. Only small reductions in total pressure ratio and efficiency compared to the solid wall can be observed. If the compressor runs with large tip clearances it notably benefits from the casing grooves. Both, total pressure and efficiency can be improved by the grooves in a similar extent as in single stage tests. Five-hole probe measurements and unsteady wall pressure measurements show the influence of the groove on the flow field. With the help of numerical investigations the different behavior of the grooves at the two tip clearance sizes will be discussed.

Tip Clearance Flow Induced Endwall Boundary Layer Separation in a Single–Stage Axial–Flow Low–Speed Compressor

2000 ◽  
Author(s):  
Horst Saathoff ◽  
Udo Stark
Keyword(s):  
Axial Flow ◽  
Boundary Layer Separation ◽  
Single Stage ◽  
Tip Clearance ◽  
Compressor Cascade ◽  
Tip Clearance Flow ◽  
Low Speed ◽  
Pressure Distributions ◽  
Oil Flow ◽  
Clearance Flow

The paper describes an investigation of the overtip end-wall flow in a single–stage axial–flow low–speed compressor utilizing an oil flow technique and a periodic multisampling pressure measurement technique. Representative oil flow pictures and ensemble averaged casingwall pressure distributions with standard deviations — supplemented by selected endwall oil flow pictures from a corresponding 2D compressor cascade — are shown and carefully analysed. The results enable the key features of the overtip endwall flow to be identified and changes with flow rate — or inlet angle — to be determined.

scholarly journals The Inner Workings of Axial Casing Grooves in a One and a Half Stage Axial Compressor With a Large Rotor Tip Gap: Changes in Stall Margin and Efficiency

2018 ◽  
Author(s):  
Chunill Hah
Keyword(s):  
Boundary Layer ◽  
Axial Compressor ◽  
Leading Edge ◽  
Tip Clearance ◽  
Flow Rates ◽  
Stall Margin ◽  
Tip Clearance Flow ◽  
Flow Boundary ◽  
Clearance Flow ◽  
Large Rotor

Effects of axial casing grooves (ACGs) on the stall margin and efficiency of a one and a half stage low-speed axial compressor with a large rotor tip gap are investigated in detail. The primary focus of the current paper is to identify the flow mechanisms behind the changes in stall margin and on the efficiency of the compressor stage with a large rotor tip gap. Semicircular axial grooves installed in the rotor’s leading edge area are investigated. A large eddy simulation (LES) is applied to calculate the unsteady flow field in a compressor stage with ACGs. The calculated flow fields are first validated with previously reported flow visualizations and stereo PIV (SPIV) measurements. An in-depth examination of the calculated flow field indicates that the primary mechanism of the ACG is the prevention of full tip leakage vortex (TLV) formation when the rotor blade passes under the axial grooves periodically. The TLV is formed when the incoming main flow boundary layer collides with the tip clearance flow boundary layer coming from the opposite direction near the casing and rolls up around the rotor tip vortex. When the rotor passes directly under the axial groove, the tip clearance flow boundary layer on the casing moves into the ACGs and no roll-up of the incoming main flow boundary layer can occur. Consequently, the full TLV is not formed periodically as the rotor passes under the open casing of the axial grooves. Axial grooves prevent the formation of the full TLV. This periodic prevention of the full TLV generation is the main mechanism explaining how the ACGs extend the compressor stall margin by reducing the total blockage near the rotor tip area. Flows coming out from the front of the grooves affect the overall performance as it increases the flow incidence near the leading edge and the blade loading with the current ACGs. The primary flow mechanism of the ACGs is periodic prevention of the full TLV formation. Lower efficiency and reduced pressure rise at higher flow rates for the current casing groove configuration are due to additional mixing between the main passage flow and the flow from the grooves. At higher flow rates, blockage generation due to this additional mixing is larger than any removal of the flow blockage by the grooves. Furthermore, stronger double-leakage tip clearance flow is generated with this additional mixing with the ACGs at a higher flow rate than that of the smooth wall.

Sign in / Sign up

Export Citation Format

Share Document