Steady and Transient Computations of Interaction Effects in a Centrifugal Compressor With Different Types of Diffusers

2010 ◽  
Author(s):  
S. Anish ◽  
N. Sitaram
Keyword(s):  
Centrifugal Compressor ◽  
Static Pressure ◽  
Leading Edge ◽  
Design Flow ◽  
Flow Coefficient ◽  
Pressure Recovery ◽  
Maximum Efficiency ◽  
Vaned Diffuser ◽  
Lower Flow ◽  
Transient Simulations

A computational study has been conducted to analyze the performance of a centrifugal compressor under various levels of impeller-diffuser interactions. The study has been conducted using a low solidity vaned diffuser (LSVD), a conventional vaned diffuser (VD) and a vaneless diffuser (VLD). The study is carried out using Reynolds-Averaged Navier-Stokes simulations. A commercial software ANSYS CFX is used for this purpose. The intensity of interaction is varied by keeping the diffuser vane leading edge at three different radial locations. Frozen rotor and transient simulations are carried out at four different flow coefficients. At design flow coefficient maximum efficiency occurs when the leading edge is at R3 (ratio of radius of the diffuser leading edge to the impeller tip radius) = 1.10. At lower flow coefficient higher stage efficiency occurs when the diffuser vanes are kept at R3 = 1.15 and at higher flow coefficient R3 = 1.05 gives better efficiency. It is observed that at lower flow coefficients positive incidence causes separation of flow at the suction side of the diffuser vane. When the flow rate is above design point there is a negative incidence at the leading edge of the diffuser vane which causes separation of flow from the pressure side of the diffuser vane. Compressor stage performance as well as performance of individual components is calculated at different time steps. Large variations in the stage performances at off-design flow coefficients are observed. The static pressure recovery coefficient (Cp) value is found to be varying with the relative position of impeller and diffuser. It is observed that maximum Cp value occurred at time step where Ψloss value is lowest. From the transient simulations it has been found that the strength and location of impeller exit wake affect the diffuser vane loading which in turn influences the diffuser static pressure recovery.

Numerical Investigation of the Inclined Leading Edge Diffuser Vane Effects on the Flow Unsteadiness and Noise Characteristics in a Transonic Centrifugal Compressor

2017 ◽  
Author(s):  
Ali Zamiri ◽  
Byung Ju Lee ◽  
Jin Taek Chung
Keyword(s):  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Pressure Fluctuations ◽  
Leading Edge ◽  
Pressure Recovery ◽  
Vaned Diffuser ◽  
Transonic Centrifugal Compressor ◽  
Transient Simulations ◽  
Leading Edges ◽  
Compressor Efficiency

The three-dimensional, compressible, unsteady Navier-Stokes equations are solved to investigate the influence of the inclined leading edge diffuser vanes on the flow field and radiated noise from a transonic centrifugal compressor with high compression ratio. The computational domain is consisted of an inlet duct and a rotating impeller with splitter blades followed by a two-dimensional wedge vaned diffuser. The numerical method was validated by comparing the steady computational results with those of experiments in terms of pressure ratio and compressor efficiency at different operating points for the original diffuser. The transient simulations were verified by comparison of the velocity distribution with PIV data in normal flow condition before the onset of surge. In the case of steady simulations, seven types of diffuser vane with various inclination angles of leading edge were numerically modeled to investigate the effects of inclined leading edge on the diffuser pressure recovery and total pressure loss characteristics. The vaned diffuser with inclined leading edge reduces the interaction between the impeller discharge flow and diffuser leading edge which leads to improve the pressure recovery characteristics within the diffuser passage. Detailed flow analysis inside the diffuser passage showed the pressure ratio and compressor efficiency have been improved by the inclined leading edges. The maximum diffuser pressure recovery coefficient, 0.7185, and compressor efficiency, 84.80%, were observed in the case of 30 degree inclination angle from hub-to-shroud. In the case of transient simulations, five different inclined leading edge diffuser vanes were numerically conducted. The present study focuses on the unsteady pressure fluctuations and noise prediction within the impeller and diffuser passages at the compressor design point. The influences of inclination angle of diffuser vane leading edges on the pressure waves with different convective velocities, generated by the impeller-diffuser interaction and pseudo-periodic unsteady separation bubbles, were captured in the time/space domain along the diffuser blade surfaces. Since it is important to understand that the far-field acoustics are dominated by the internal pressure fluctuations inside the passages, the near-field pressure fluctuation spectra captured at the impeller-diffuser interface are evaluated to analyze the tonal BPF noise as the main noise source in the centrifugal compressors. It is shown that the inclined leading edges are very useful not only for improvement of the pressure recovery characteristics within the diffuser but also for the reduction of the interaction tonal BPF noise (around 7.6 dB SPL reduction). Furthermore, it was found that by using the inclined leading edge, the vortical structures and separations within the diffuser passages were reduced which may cause the attenuation of the broadband noise components and the overall sound pressure level.

Some Studies on Low Solidity Vaned Diffusers of a Centrifugal Compressor Stage

2005 ◽  
Author(s):  
T. Ch. Siva Reddy ◽  
G. V. Ramana Murty ◽  
Prasad Mukkavilli ◽  
D. N. Reddy
Keyword(s):  
Centrifugal Compressor ◽  
Static Pressure ◽  
Pressure Ratio ◽  
Pressure Recovery ◽  
Compressor Stage ◽  
Recovery Coefficient ◽  
Vaned Diffuser ◽  
Flow Angle ◽  
Centrifugal Compressor Stage ◽  
Pressure Recovery Coefficient

Numerical simulation of impeller and low solidity vaned diffuser (LSD) of a centrifugal compressor stage is performed individually using CFX- BladeGen and BladeGenPlus codes. The tip mach number for the chosen study was 0.35. The same configuration was used for experimental investigation for a comparative study. The LSD vane is formed using standard NACA profile with marginal modification at trailing edge. The performance parameters obtained form numerical studies at the exit of impeller and the diffuser have been compared with the corresponding experimental data. These parameters are pressure ratio, polytropic efficiency and flow angle at the impeller exit where as the parameters those have been compared at the exit of diffuser are the static pressure recovery coefficient and the exit flow angle. In addition, the numerical prediction of the blade loading in terms of blade surface pressure distribution on LSD vane has been compared with the corresponding experimental results. Static pressure recovery coefficient and flow angle at diffuser exit is seen to match closely at higher flows. The difference at lower flows could be due to the effect of interaction between impeller and diffuser combinations, as the numerical analysis was done separately for impeller and diffuser and the effect of impeller diffuser interaction was not considered.

Effects of Inlet Pressure Distortion on the Performance and Flow Field of a Centrifugal Compressor at Off-Design Conditions

2012 ◽  
Author(s):  
N. Sitaram ◽  
M. Govardhan ◽  
K. V. Murali
Keyword(s):  
Flow Field ◽  
Centrifugal Compressor ◽  
Total Pressure ◽  
Static Pressure ◽  
Design Flow ◽  
Flow Coefficient ◽  
Low Flow ◽  
Performance Measurements ◽  
Perforated Sheet ◽  
Sector Angle

The present paper presents experimental results on the effects of inlet total pressure distortion on the performance and flow field of a centrifugal compressor. The total pressure at inlet is artificially distorted by means of a perforated sheet, which is supported by a support mesh. A total of eleven configurations, including clean inlet configuration, are tested. Performance measurements and impeller inlet and exit flow studies at three flow coefficients, one near design flow coefficient, one below design flow coefficient and one above design flow coefficient, are carried out. The present paper presents and discusses results at off-design flow coefficients and the effects of stage loading on the distortion effects are presented. A new parameter, Distortion Index (DI) is introduced. As DI increases, the mass averaged total pressure at exit stations decreases. Distortion sector angle of 60° having the lowest total pressure is found to be the critical sector for circumferential distortion configurations. As the Distortion Correlation parameter, DC(60) increases, the mass averaged total pressure for circumferential distortion configuration decreases, except in the case of low flow coefficient where DC(60) is nearly constant. DC(60) also increases with sector angle. The static pressure normalized with static pressure for clean inlet decreases as the distortion sector angle is increased. Distortion attenuates the static pressure as the flow passes through the vaneless diffuser. The attenuation increases with the distortion sector angle.

scholarly journals The Centrifugal Compressor Inducer

1998 ◽  
Author(s):  
C. Rodgers
Keyword(s):  
Centrifugal Compressor ◽  
Static Pressure ◽  
The State ◽  
Design Flow ◽  
Pressure Recovery ◽  
Centrifugal Compressors ◽  
High Static Pressure ◽  
Stable Flow ◽  
State Of Art

The function of the centrifugal compressor inducer is to provide wide flow margins from the design flow to the stall and choke flow limits, together with high static pressure recovery. At transonic conditions the inducer becomes the critical to impeller performance in that shock losses and blockage growth diminish stable flow range and may trigger near vertical stage characteristics. The paper covers the various types of inlet configurations upstream of the inducer, followed by a review of the state-of-art inducer design for centrifugal compressors, culminating with some research developments in transonic inducer blading characteristics.

Structure of Diffuser Stall and Unsteady Vortices in a Centrifugal Compressor With Vaned Diffuser

2016 ◽  
Author(s):  
Nobumichi Fujisawa ◽  
Sota Ikezu ◽  
Yutaka Ohta
Keyword(s):  
Centrifugal Compressor ◽  
Leading Edge ◽  
Rotating Stall ◽  
Design Flow ◽  
Tip Leakage Flow ◽  
Vaned Diffuser ◽  
Tip Leakage ◽  
Close Proximity ◽  
Edge Vortex ◽  
Flow Blockage

The characteristics of a diffuser rotating stall and the evolution of a vortex generated on the diffuser leading edge (i.e., leading-edge vortex (LEV)) in a centrifugal compressor were investigated using experiments and numerical analyses. The experimental results showed that both impeller and diffuser rotating stalls occurred at 55 and 25 Hz during off-design flow operation. Both the stall cells existed only on the shroud side of the flow passages, which is in close proximity to the source location of the LEV. The numerical results showed that the LEV is a combination of a separated vortex near the leading edge and the extended tip-leakage flow from the impeller. In the partial flow operation, the LEV develops as the velocity decreases in the diffuser passages and forms a huge flow blockage within the diffuser passages. Therefore, the LEV may be considered to be one of the causes of diffuser stall in the centrifugal compressor.

scholarly journals Transition Process from Diffuser Stall to Stage Stall in a Centrifugal Compressor with a Vaned Diffuser

2017 ◽  
Vol 2017 ◽  
pp. 1-13 ◽  
Author(s):  
Nobumichi Fujisawa ◽  
Yutaka Ohta
Keyword(s):  
Centrifugal Compressor ◽  
Vortical Structure ◽  
Leading Edge ◽  
Transition Process ◽  
Rotating Stall ◽  
Design Flow ◽  
Longitudinal Vortex ◽  
Velocity Measurements ◽  
Suction Surface ◽  
Vaned Diffuser

The transition process from a diffuser rotating stall to a stage stall in a centrifugal compressor with a vaned diffuser was investigated by experimental and numerical analyses. From the velocity measurements, it was found that the rotating stall existed on the shroud side of the diffuser passage in the off-design flow condition. The numerical results revealed the typical vortical structure of the diffuser stall. The diffuser stall cell was caused by the systematic vortical structure which consisted of the tornado-type vortex, the longitudinal vortex at the shroud/suction surface corner (i.e., leading edge vortex (LEV)), and the vortex in the throat area of the diffuser passages. Furthermore, the stage stall, which rotated within both the impeller and diffuser passages, occurred instead of the diffuser stall as the mass flow rate was decreased. According to the velocity measurements at the diffuser inlet, the diffuser stall which rotated on the shroud side was shifted to the hub side. Then, the diffuser stall moved into the impeller passages and formed the stage stall. Therefore, the stage stall was caused by the development of the diffuser stall, which transferred from the shroud side to the hub side in the vaneless space and expanded to the impeller passages.

Adaptive Vaned Diffuser for Centrifugal Compressor

2005 ◽  
Author(s):  
G. Ferrara ◽  
L. Ferrari ◽  
L. Baldassarre
Keyword(s):  
Centrifugal Compressor ◽  
High Efficiency ◽  
Flow Coefficient ◽  
Maximum Efficiency ◽  
Vaned Diffuser ◽  
Flow Angle ◽  
Loop Control ◽  
Loop Control System ◽  
Actual Flow ◽  
Close Loop Control

Vaned diffusers are often preferred to a vaneless solution for improving maximum efficiency. The drawbacks of this choice are the reduction of stable working range and a narrower flow coefficient range at high efficiency. In this paper a solution to the above mentioned problems is presented. The solution proposed involves an adaptive vaned diffuser: the vanes can be oriented in order to find the optimum incidence by means of a mechanism moved by an oleo-dynamic piston. Several sensor typologies have been tested to find which is the best to assess the actual flow angle. The aim is to correlate the optimum vane position with sensor output in order to provide a close-loop control system. An experimental analysis was carried out on an intermediate centrifugal compressor stage to validate this approach.

Effects of Diffuser Vane Geometries on Compressor Performance and Noise Characteristics in a Centrifugal Compressor

2013 ◽  
Author(s):  
Yohei Morita ◽  
Nobumichi Fujisawa ◽  
Takashi Goto ◽  
Yutaka Ohta
Keyword(s):  
Centrifugal Compressor ◽  
Noise Level ◽  
Leading Edge ◽  
Broadband Noise ◽  
Frequency Noise ◽  
Numerical Techniques ◽  
Vaned Diffuser ◽  
Noise Characteristics ◽  
Edge Vortex ◽  
Compressor Performance

The effects of the diffuser vane geometries on the compressor performance and noise characteristics of a centrifugal compressor equipped with vaned diffusers were investigated by experiments and numerical techniques. Because we were focusing attention on the geometries of the diffuser vane’s leading edge, diffuser vanes with various leading edge geometries were installed in a vaned diffuser. A tapered diffuser vane with the tapered portion near the leading edge of the diffuser’s hub-side could remarkably reduce both the discrete frequency noise level and broadband noise level. In particular, a hub-side tapered diffuser vane with a taper on only the hub-side could suppress the development of the leading edge vortex (LEV) near the shroud side of the diffuser vane and effectively enhanced the compressor performance.

Increasing Inducer Stability and Suction Performance With a Stability Control Device

2018 ◽  
Vol 141 (1) ◽  
Author(s):  
R. Lundgreen ◽  
D. Maynes ◽  
S. Gorrell ◽  
K. Oliphant
Keyword(s):  
Fluid Dynamic ◽  
Leading Edge ◽  
High Energy ◽  
Stability Control ◽  
Control Device ◽  
Design Flow ◽  
Flow Coefficient ◽  
Blade Tip ◽  
Rotordynamic Forces ◽  
Suction Performance

An inducer is used as the first stage of high suction performance pump. It pressurizes the fluid to delay the onset of cavitation, which can adversely affect performance in a centrifugal pump. In this paper, the performance of a water pump inducer has been explored with and without the implementation of a stability control device (SCD). This device is an inlet cover bleed system that removes high-energy fluid near the blade leading edge and reinjects it back upstream. The research was conducted by running multiphase, time-accurate computational fluid dynamic (CFD) simulations at the design flow coefficient and at low, off-design flow coefficients. The suction performance and stability for the same inducer with and without the implementation of the SCD has been explored. An improvement in stability and suction performance was observed when the SCD was implemented. Without the SCD, the inducer developed backflow at the blade tip, which led to rotating cavitation and larger rotordynamic forces. With the SCD, no significant cavitation instabilities developed, and the rotordynamic forces remained small. The lack of cavitation instabilities also allowed the inducer to operate at lower inlet pressures, increasing the suction performance of the inducer.

Non-Uniform Two-Phase Flow of Supercritical Carbon Dioxide Centrifugal Compressor

2020 ◽  
Author(s):  
Wenrui Bao ◽  
Ce Yang ◽  
Li Fu ◽  
Changmao Yang ◽  
Lucheng Ji
Keyword(s):  
Carbon Dioxide ◽  
Supercritical Carbon Dioxide ◽  
Flow Field ◽  
Centrifugal Compressor ◽  
Static Pressure ◽  
Leading Edge ◽  
Phase Region ◽  
Tip Clearance ◽  
Two Phase ◽  
Supercritical Carbon

Abstract An asymmetric structure of volute in a supercritical carbon dioxide centrifugal compressor induces a non-uniform circumferential distribution of the upstream flow field, which inevitably affects the formation of a two-phase region of carbon dioxide in an impeller. In this work, unsteady simulations for centrifugal compressors were conducted. First, the influence of low static strip induced by low static pressure near volute tongue on the impeller flow field was presented. Then, the non-uniform flow field distribution in the impeller passages and flow characteristics of the passages at the impeller inlet were obtained. Finally, the two-phase regions in the impeller were presented. The results demonstrate that for a centrifugal compressor with volute, the two-phase region appears not only on the suction surface of the leading edge of the blade, but also in some impeller passages, on the pressure surface of the blade near the leading edge, and in the leading edge and mid-chord of tip clearance, under the design conditions. The low static pressure strip induced by the volute leads to a high-speed region in the impeller passages where the temperature and pressure of supercritical carbon dioxide fall below the critical point and carbon dioxide enters the two-phase region. Meanwhile, the static pressure on the blade surface is distorted under the influence of a high-speed region in the passages, resulting in the formation of a two-phase region at the tip clearance. The flow distortion of passages at the impeller inlet results in the appearance of two-phase regions on the both sides of leading edge of the blade. The dryness on the suction side of the blade leading edge and the leading edge of the tip clearance is lower, which indicated that the proportion of liquid-phase carbon dioxide is higher in these two-phase regions.

Sign in / Sign up

Export Citation Format

Share Document