Effects of the Swirl Velocity of a Jet in Crossflow From Fan Assemblies Mounted on Lifting Surfaces

2010 ◽  
Author(s):  
Alexandros Terzis ◽  
Charilaos Kazakos ◽  
Nikolaos Papadopoulos ◽  
Anestis I. Kalfas ◽  
Pavlos K. Zachos ◽  
...  
Keyword(s):  
Flight Control ◽  
Film Cooling ◽  
Thermal Protection ◽  
Turbine Blades ◽  
Cross Flow ◽  
Vortex Pair ◽  
Main Stream ◽  
Injection Hole ◽  
Swirl Velocity ◽  
Wide Range

The penetration of a jet of fluid into a traversal moving stream is a basic configuration of a wide range of engineering applications, such as film cooling and V/STOL aircrafts. This investigation examines experimentally the effect of blowing ratio of fans in cross flow, and numerically, the effect of the swirl velocity of jets in cross flow, downstream of the injection hole. The experimental results indicated an agreement with typically straight jets in cross flow (no vorticity), illustrating that the trace of the jet, remains close to the wall and subsequently enhance cooling at low blowing ratios in the case of turbine blade applications. However, the rotation of the jet results in an imparity between the two parts of the counter rotating vortex pair (CVP), and as a consequence, the injected fluid not only bends in the direction of the main stream but also diverts in the direction of the rotation, in order to conserve its angular momentum. The induction of the swirl velocity on the injected jet destructs one of the two parts of the kidney vortex which entrains fluid from the cross flow to the jet promoting the mixing between the two fluids, while the trace of a swirled jet remains closer to the wall downstream of the injection hole. Finally, the use of contra rotating jet or fan configurations reduces the wall shear stress in a very great extent, leading to better thermal protection of turbine blades, as well as cancels out the yaw torques of each fan separately, resulting in better flight control of typical lift surface.

Effects of Swirl Velocities From Fan Assemblies Mounted on Lifting Surfaces

2010 ◽  
Vol 133 (3) ◽  
Author(s):  
Alexandros Terzis ◽  
Charilaos Kazakos ◽  
Nikolaos Papadopoulos ◽  
Anestis Kalfas ◽  
Pavlos K. Zachos ◽  
...  
Keyword(s):  
Flight Control ◽  
Film Cooling ◽  
Thermal Protection ◽  
Turbine Blades ◽  
Vortex Pair ◽  
Main Stream ◽  
Injection Hole ◽  
Two Fluids ◽  
Swirl Velocity ◽  
Wide Range

The penetration of a jet of fluid into a traversal moving stream is a basic configuration of a wide range of engineering applications, such as film cooling and V/STOL aircrafts. This investigation examines experimentally the effect of blowing ratio of fans in crossflow, and numerically, the effect of the swirl velocity of jets in crossflow, downstream of the injection hole. The experimental results indicated an agreement with typically straight jets in crossflow (no vorticity), illustrating that the trace of the jet, remains close to the wall and subsequently enhance cooling at low blowing ratios in the case of turbine blade applications. However, the rotation of the jet results in an imparity between the two parts of the counter rotating vortex pair and as a consequence, the injected fluid not only bends in the direction of the main stream but also diverts in the direction of the rotation in order to conserve its angular momentum. The induction of the swirl velocity on the injected jet destructs one of the two parts of the kidney vortex, which entrains fluid from the crossflow to the jet promoting the mixing between the two fluids while the trace of a swirled jet remains closer to the wall downstream of the injection hole. Finally, the use of contrarotating jet or fan configurations reduces the wall shear stress in a very great extent, leading to better thermal protection of turbine blades, as well as cancels out the yaw torques of each fan separately, resulting in better flight control of typical lift surface.

Parametric Study on Anti-Vortex Film Cooling Hole Arrangements

2014 ◽  
Vol 660 ◽  
pp. 664-668
Author(s):  
Kamil Abdullah ◽  
Hazim Fadli Aminnuddin ◽  
Akmal Nizam Mohammed
Keyword(s):  
Film Cooling ◽  
Thermal Protection ◽  
Turbine Blades ◽  
Vortex Pair ◽  
Navier Stokes ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Hole ◽  
Lateral Film ◽  
Lift Off

Film cooling has been extensively used to provide thermal protection for the external surface of the gas turbine blades. Numerous number of film cooling holes designs and arrangements have been introduced. The main motivation of these designs and arrangements are to reduce the lift-off effect cause by the counter rotating vortices (CRVP) produce by cylindrical cooling hole. One of the efforts is the introduction of newly found anti-vortex film cooling design. The present study focuses on anti-vortex holes arrangement consists of a main hole and pair of smaller holes. All three holes share a common inlet with the outlet of the smaller holes varies base on it relative position towards the main hole. Three anti-vortex holes arrangements have been considered; downstream anti-vortex hole arrangement (DAV), lateral anti-vortex hole arrangement (LAV), and upstream anti-vortex hole arrangement (UAV). In addition, a single hole (SH) film cooling has also been considered as the baseline. The investigation make used of ANSYS CFX software ver. 14. The investigations are made through Reynolds Average Navier Stokes analyses with the application of shear k-ε turbulence model. The results show that the anti-vortex designs produce significant improvement in term of film cooling effectiveness and distribution. The LAV arrangement shows the best film cooling effectiveness distribution among all considered cases and is consistent for all blowing ratios (BR). The results also unveil the formation of new vortex pair on both side of the primary hole CRVP. Interaction between the new vortices and the main CRVP structure reduce the lift off explaining the increased lateral film effectiveness.

Large Eddy Simulations of Film-Cooling Flows With a Micro-Ramp Vortex Generator

2011 ◽  
Author(s):  
Aaron F. Shinn ◽  
S. Pratap Vanka
Keyword(s):  
Film Cooling ◽  
Cross Flow ◽  
Vortex Generator ◽  
Vortex Pair ◽  
Large Eddy Simulations ◽  
Wind Tunnel Experiments ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Flows ◽  
Large Eddy

Large Eddy Simulations were performed to study the effect of a micro-ramp on an inclined turbulent jet interacting with a cross-flow in a film-cooling configuration. The micro-ramp vortex generator is placed downstream of the film-cooling jet. Changes in vortex structure and film-cooling effectiveness are evaluated and the genesis of the counter-rotating vortex pair in the jet is discussed. Results are reported with the jet modeled using a plenum/pipe configuration. This configuration was designed based on previous wind tunnel experiments at NASA Glenn Research Center, and the present results are meant to supplement those experiments. It is found that the micro-ramp improves film-cooling effectiveness by generating near-wall counter-rotating vortices which help entrain coolant from the jet and transport it to the surface. The pair of vortices generated by the micro-ramp are of opposite sense to the vortex pair embedded in the jet.

scholarly journals Numerical Prediction of Film Cooling Effectiveness and the Associated Aerodynamic Losses With a Three-Dimensional Calculation Procedure

1990 ◽  
Author(s):  
G. H. Dibelius ◽  
R. Pitt ◽  
B. Wen
Keyword(s):  
Experimental Data ◽  
Film Cooling ◽  
Reverse Flow ◽  
Turbine Blades ◽  
Three Dimensional ◽  
Temperature Pattern ◽  
Main Stream ◽  
Cooling Efficiency ◽  
Film Cooling Effectiveness ◽  
Aerodynamic Losses

Film cooling of turbine blades by injecting air through holes or slots affects the main stream flow. A numerical model has been developed to predict the resulting three-dimensional flow and the temperature pattern under steady flow conditions. An elliptic procedure is used in the near injection area to include reverse flow situations, while in the upstream area as well as far downstream a partial-parabolic procedure is applied. As first step an adiabatic wall has been assumed as boundary condition, since for this case experimental data are readily available for comparison. At elevated momentum blowing rates, zones of reverse flow occur downstream of the injection holes resulting in a decrease of cooling efficiency. A variation of the relevant parameters momentum blowing rate m, injection angle α and ratio of hole spacing to diameter s/d revealed the combination of m ≈ 1, α ≈ 30° and s/d ≈ 2 to be the optimum with respect to the averaged cooling efficiency and to the aerodynamic losses. Cooling is more efficient with slots than with a row of holes not considering the related problems of manufacture and service life. The calculated temperature patterns compare well with the experimental data available.

Effects of an Embedded Vortex on Injectant From a Single Film-Cooling Hole in a Turbulent Boundary Layer

1990 ◽  
Vol 112 (3) ◽  
pp. 428-436 ◽  
Author(s):  
P. M. Ligrani ◽  
W. Williams
Keyword(s):  
Heat Transfer ◽  
Vortex Core ◽  
Film Cooling ◽  
Thermal Protection ◽  
Hole Diameter ◽  
Secondary Flows ◽  
Stream Velocity ◽  
Vortex Center ◽  
Injection Hole ◽  
Cooling Hole

Effects of embedded longitudinal vortices on heat transfer in turbulent boundary layers with injection from a single film-cooling hole are described. These results were obtained at a free-stream velocity of 10 m/s, with a film-cooling hole inclined 30 deg to the horizontal and a blowing ratio of about 0.50. The ratio of vortex core diameter to injection hole diameter was 1.58, and the ratio of circulation to injection velocity time hole diameter was about 3.16. Coolant distributions and spatially resolved heat transfer measurements indicate that injection hole centerlines must be at least 2.9–3.4 vortex core diameters away from the vortex center in the lateral direction to avoid significant alterations to wall heat transfer and distributions of film coolant. Under these circumstances, protection from film cooling is evident at least up to 55 hole diameters downstream of injection. When the injection hole is closer to the vortex center, secondary flows convect most injectant into the vortex upwash and thermal protection from film cooling is destroyed for streamwise locations from the injection hole greater than 17.5 hole diameters.

CFD Investigation of the Flow of Trailing Edge Cooling Slots

2018 ◽  
Author(s):  
Y. Jiang ◽  
N. Gurram ◽  
E. Romero ◽  
P. T. Ireland ◽  
L. di Mare
Keyword(s):  
Mach Number ◽  
Kinetic Energy ◽  
Flow Separation ◽  
Film Cooling ◽  
High Speed ◽  
Turbine Blades ◽  
Cross Flow ◽  
Turbulent Energy ◽  
Trailing Edge ◽  
Flow Interactions

Slot film cooling is a popular choice for trailing edge cooling in high pressure (HP) turbine blades because it can provide more uniform film coverage compared to discrete film cooling holes. The slot geometry consists of a cut back in the blade pressure side connected through rectangular openings to the internal coolant feed passage. The numerical simulation of this kind of film cooling flows is challenging due to the presence of flow interactions like step flow separation, coolant-mainstream mixing and heat transfer. The geometry under consideration is a cutback surface at the trailing edge of a constant cross-section aerofoil. The cutback surface is divided into three sections separated by narrow lands. The experiments are conducted in a high speed cascade in Oxford Osney Thermo-Fluids Laboratory at Reynolds and Mach number distributions representative of engine conditions. The capability of CFD methods to capture these flow phenomena is investigated in this paper. The isentropic Mach number and film effectiveness are compared between CFD and pressure sensitive paint (PSP) data. Compared to steady k–ω SST method, Scale Adaptive Simulation (SAS) can agree better with the measurement. Furthermore, the profiles of kinetic energy, production and shear stress obtained by the steady and SAS methods are compared to identify the main source of inaccuracy in RANS simulations. The SAS method is better to capture the unsteady coolant-hot gas mixing and vortex shedding at the slot lip. The cross flow is found to affect the film significantly as it triggers flow separation near the lands and reduces the effectiveness. The film is non-symmetric with respect to the half-span plane and different flow features are present in each slot. The effect of mass flow ratio (MFR) on flow pattern and coolant distribution is also studied. The profiles of velocity, kinetic energy and production of turbulent energy are compared among the slots in detail. The MFR not only affects the magnitude but also changes the sign of production.

Effect of Internal Coolant Crossflow on the Effectiveness of Shaped Film-Cooling Holes

2003 ◽  
Vol 125 (3) ◽  
pp. 547-554 ◽  
Author(s):  
Michael Gritsch ◽  
Achmed Schulz ◽  
Sigmar Wittig
Keyword(s):  
Film Cooling ◽  
Gas Flow ◽  
Flow Direction ◽  
Turbine Blades ◽  
Density Ratio ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Hot Gas ◽  
Wide Range

Film-cooling was the subject of numerous studies during the past decades. However, the effect of flow conditions on the entry side of the film-cooling hole on film-cooling performance has surprisingly not received much attention. A stagnant plenum which is widely used in experimental and numerical studies to feed the holes is not necessarily a right means to re-present real engine conditions. For this reason, the present paper reports on an experimental study investigating the effect of a coolant crossflow feeding the holes that is oriented perpendicular to the hot gas flow direction to model a flow situation that is, for instance, of common use in modern turbine blades’ cooling schemes. A comprehensive set of experiments was performed to evaluate the effect of perpendicular coolant supply direction on film-cooling effectiveness over a wide range of blowing ratios (M=0.5…2.0) and coolant crossflow Mach numbers Mac=0…0.6. The coolant-to-hot gas density ratio, however, was kept constant at 1.85 which can be assumed to be representative for typical gas turbine applications. Three different hole geometries, including a cylindrical hole as well as two holes with expanded exits, were considered. Particularly, two-dimensional distributions of local film-cooling effectiveness acquired by means of an infrared camera system were used to give detailed insight into the governing flow phenomena. The results of the present investigation show that there is a profound effect of how the coolant is supplied to the hole on the film-cooling performance in the near hole region. Therefore, crossflow at the hole entry side has be taken into account when modeling film-cooling schemes of turbine bladings.

Experimental Study on Pressure Losses in Circular Orifices With Inlet Cross Flow

2018 ◽  
Vol 140 (7) ◽  
Author(s):  
Daniel Feseker ◽  
Mats Kinell ◽  
Matthias Neef
Keyword(s):  
Experimental Study ◽  
Film Cooling ◽  
Gas Turbines ◽  
Discharge Coefficient ◽  
Pressure Ratio ◽  
Cross Flow ◽  
Pressure Losses ◽  
Wide Range ◽  
Cooling Hole ◽  
Secondary Air

The ability to understand and predict the pressure losses of orifices is important in order to improve the air flow within the secondary air system. This experimental study investigates the behavior of the discharge coefficient for circular orifices with inlet cross flow which is a common flow case in gas turbines. Examples of this are at the inlet of a film cooling hole or the feeding of air to a blade through an orifice in a rotor disk. Measurements were conducted for a total number of 38 orifices, covering a wide range of length-to-diameter ratios, including short and long orifices with varying inlet geometries. Up to five different chamfer-to-diameter and radius-to-diameter ratios were tested per orifice length. Furthermore, the static pressure ratio across the orifice was varied between 1.05 and 1.6 for all examined orifices. The results of this comprehensive investigation demonstrate the beneficial influence of rounded inlet geometries and the ability to decrease pressure losses, which is especially true for higher cross flow ratios where the reduction of the pressure loss in comparison to sharp-edged holes can be as high as 54%. With some exceptions, the chamfered orifices show a similar behavior as the rounded ones but with generally lower discharge coefficients. Nevertheless, a chamfered inlet yields lower pressure losses than a sharp-edged inlet. The obtained experimental data were used to develop two correlations for the discharge coefficient as a function of geometrical as well as flow properties.

Effect of blowing ratio on Film-Cooling effectiveness of Ginkgo Shaped Holes: A numerical approach

2021 ◽  
Author(s):  
Muhammad Awais ◽  
Reaz Hasan ◽  
Md. Hamidur Rahman
Keyword(s):  
Film Cooling ◽  
Gas Turbines ◽  
Thermal Protection ◽  
Turbine Blades ◽  
Operating Conditions ◽  
Bottom Surface ◽  
Inlet Temperature ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Lift Off

Modern gas turbine engines operate at significantly high temperatures to improve thermal efficiency and power output to a greater extent. The enhancement in rotor inlet temperature (RIT) increases the heat transfer rate to the turbine blades which requires sophisticated cooling schemes to maintain the blade temperature in acceptable levels. Therefore, the present work refers to the numerical investigation of film cooling technique applied in gas turbines. The cooling performance of two different shaped holes namely Ginkgo Forward (GF) and Ginkgo Reverse (GR)) were investigated in terms of centerline and local lateral effectiveness and comprehensive comparison was made with the cooling performance of cylindrical (CY) hole. The investigations were performed at two density ratios (DR=1.6, 2.0) and three different blowing ratios (BR=1.0, 1.5 and 2.0). At all the operating conditions, the results demonstrated significant augmentation in centerline and lateral effectiveness when GR shaped hole was employed followed by the GF and CY cooling holes. For shaped holes, the low velocity gradient through the film alleviated jet lift off and turbulence intensity resulting in decreased entrainment of hot gas to bottom surface. To conclude, the lateral coverage due to the shaped cooling holes significantly enhanced the thermal protection and overall cooling performance.

scholarly journals Influence of Internal Flow on Film Cooling Effectiveness

1999 ◽  
Author(s):  
Günter Wilfert ◽  
Stefan Wolff
Keyword(s):  
Film Cooling ◽  
Cross Flow ◽  
Vortex Generator ◽  
Internal Flow ◽  
Main Stream ◽  
Thermochromic Liquid Crystal ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Hole ◽  
Inlet Conditions

Film cooling experiments were conducted to investigate the effects of internal flow conditions and plenum geometry on the film cooling effectiveness. The film cooling measurements show a strong influence of the coolant inlet conditions on film cooling performance. The present experiments were carried out on a flat plate with a row of cylindrical holes oriented at 30 degrees with respect to a constant-velocity external flow, systematically varying the plenum geometry and blowing rates (0.5≤M≤1.25). Adiabatic film cooling measurements using the multiple narrow-banded Thermochromic Liquid Crystal-technique (TLC) were carried out simulating a flow parallel to the main stream flow with and without cross flow at the coolant hole entry compared with a standard plenum configuration. An impingement in front of the cooling hole entry with and without cross flow was also investigated. For all parallel flow configurations ribs were installed at the top and bottom coolant channel wall. As the hole length-to-diameter ratio has an influence on the film cooling effectiveness, the wall thickness has also been varied. In order to optimise the benefit of the geometry effects with ribs, a vortex generator was designed and tested. Results from these experiments show in a region 5≤X/D≤80 downstream of the coolant injection location differences in adiabatic film cooling effectiveness between +5% and +65% compared with a standard plenum configuration.

Sign in / Sign up

Export Citation Format

Share Document