The Influences of Film Hole Size and Coolant Ejection Angle on Overall Cooling Effectiveness of Laminated Cooling

2014 ◽  
Author(s):  
Xiao-Dong Zhang ◽  
Jian-Jun Liu ◽  
Bai-Tao An
Keyword(s):  
Film Cooling ◽  
Gas Turbines ◽  
Pressure Coefficient ◽  
Computation Method ◽  
Cooling Effectiveness ◽  
Baseline Design ◽  
Pin Fin ◽  
Staggered Arrangement ◽  
Lift Off ◽  
Cooling Element

The laminated cooling or the layered cooling configuration with integrated impingement, rib-roughed and film cooling can result in a high overall cooling effectiveness and is believed to be a promising cooling technology for the next generation of advanced gas turbines. Previous studies found that the relative locations among the film hole, impingement hole and the pin-fin (i.e., cooling element arrangement) have strong impacts on the cooling effectiveness of the laminated configuration. The laminated configurations with staggered arrangement were investigated in the present paper. Two measures were used to enhance the overall cooling effectiveness, including increasing the area ratio of film hole to cooling area and employing angled film hole. Fluid-thermal coupled computations (conjugate heat transfer) were performed for assessing the overall cooling effectiveness and the pressure coefficient, and the computation method was validated by the experimental data. The computational results for the baseline design show that the area-averaged cooling effectiveness is 0.717 at BR = 1.77 and the film cooling needs to be further enhanced. Through enlarging the diameter of the film hole from 0.8mm to 1.2mm, the lift-off of film coolant is restrained and the cooling effectiveness is increased at the downstream of film hole. By employing angled film hole, the area-averaged cooling effectiveness is increased and the coolant flow resistance is also reduced.

The NEKOMIMI Cooling Technology: Cooling Holes With Ears for High-Efficient Film Cooling

2011 ◽  
Author(s):  
Karsten Kusterer ◽  
Anas Elyas ◽  
Dieter Bohn ◽  
Takao Sugimoto ◽  
Ryozo Tanaka ◽  
...  
Keyword(s):  
Film Cooling ◽  
Gas Turbines ◽  
Experimental Investigations ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
High Efficient ◽  
Cylindrical Holes ◽  
Cooling Technology ◽  
Lift Off ◽  
Cooling Air

Further improvement of the thermal efficiency of modern gas turbines can be achieved by a further reduction of the cooling air amount. Therefore, it is necessary to increase the cooling effectiveness, so that the available cooling air fulfils the cooling task even if the amount has been reduced. Due to experimental and numerical efforts, it is well understood today that aerodynamic mixing processes are enhanced by counter-rotating vortices (CRV) in the cooling jets and lead to jet lift-off effects. Thus, the film-cooling effectiveness is reduced soon behind the cooling air ejection through the holes. Due to that basic understanding, different technologies for improving film cooling have been developed. Some of them focus on establishing anti-counter-rotating vortices (ACRV) inside the cooling jet that prevent the hot gas from flowing underneath the jet and, thus, avoid the lift-off effect. One of these technologies is the double-jet film cooling (DJFC), invented by the authors, where the special arrangement of two cylindrical holes lead to a cooling jet with such an anti-vortex system. However, beside the advantage that the holes are simple cylindrical holes, one disadvantage is that appropriate supply with cooling air for both holes is sometimes difficult to be established in real configurations. Thus, the authors have followed the idea to transfer the original double-jet film cooling principle to a special configuration with merged holes. Thus, in that case only one air supply is necessary but the anti-vortex effect has been preserved. The derived cooling technology has been named NEKOMIMI technology. The paper explains the principle of that technology. Results from experimental investigations including film cooling effectiveness measurements for the new technology are presented. The results are compared to conventional cooling hole configurations showing the tremendous positive effect in reaching highest film cooling effectiveness for the new configuration at M = 1.5 and partly for M = 1. Numerical investigations for the M = 1.5 case indicate that the existence of the ACRV is the likely reason for the enhanced cooling performance of the new configuration.

A Three-Regime Based Method for Correlating Film Cooling Effectiveness for Cylindrical and Shaped Holes

2015 ◽  
Author(s):  
Lieke Wang ◽  
Mats Kinell ◽  
Hossein N. Najafabadi ◽  
Matts Karlsson
Keyword(s):  
Experimental Data ◽  
Film Cooling ◽  
Gas Turbines ◽  
Density Ratio ◽  
Transition Regime ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Lift Off

To cope with high temperature of the gas from combustor, cooling is often used in the hot gas components in gas turbines. Film cooling is one of the effective methods used in this application. Both cylindrical and fan-shaped holes are used in film cooling. There have been a number of correlations published for both cylindrical and fan-shaped holes regarding film cooling effectiveness. Unfortunately there are no definitive correlations for either cylindrical or fan-shaped holes. This is due to the nature of the complexity of film cooling where many factors influence its performance, e.g., blowing ratio, density ratio, surface angle, downstream distance, expansion angle, hole length, turbulence level, etc. A test rig using infrared camera was built to test the film cooling performance for a scaled geometry from a real nozzle guide vane. Both cylindrical and fan-shaped holes were tested. To correlate the experimental data, a three-regime based method was developed for predicting the film cooling effectiveness. Based on the blowing ratio, the proposed method divides the film cooling performance in three regimes: fully attached (or no jet lift-off), fully jet lift-off, and the transition regime in between. Two separate correlations are developed for fully attached and full jet lift-off regimes, respectively. The method of interpolation from these two regimes is used to predict the film cooling effectiveness for the transition regime, based on the blowing ratio. It has been found this method can give a good correlation to match the experimental data, for both cylindrical and fan-shaped holes. A comparison with literature was also carried out, and it showed a good agreement.

New Designs of Novel Holes Based on Cylindrical Configurations for Improving Film Cooling Effectiveness

2018 ◽  
Author(s):  
Rui Zhu ◽  
Gongnan Xie ◽  
Terrence W. Simon
Keyword(s):  
Film Cooling ◽  
Gas Turbines ◽  
Thermal Protection ◽  
Cylindrical Hole ◽  
Two Stage ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Vortex Pairs ◽  
Shaped Hole ◽  
Lift Off

In modern gas turbines, film cooling technology is the most common and efficient way to provide thermal protection for hot parts. To improve film cooling effectiveness, different kinds of shaped holes have been designed, but most of them are complicated and difficult to machine. In this study, four cases of novel film cooling hole design, all based on cylindrical holes, are numerically studied. One is a single, two-stage cylindrical hole, whose downstreamhalf-length has a diameter D while the upstreamhalf-length has a diameter D/2. A second has a cylindrical primary hole with two smaller secondary holes located symmetrically about the centerline of the primary hole and downstream of the primary hole. The three holes of this second design are then combined to make a single shaped hole, constituting a third case, called the tri-circular shaped hole. The entry part of the third case is replaced by a cylindrical hole with a diameter of half the primary hole diameter, making a fourth case called the two-stage tri-circular shaped hole. Film cooling effectiveness and surrounding thermal and flow fields are numerically investigated for all four cases using various blowing ratios. It is shown from the simulation that the two-stage cylindrical hole cannot improve film cooling effectiveness. The primary hole with two secondary holes can enhance film cooling performance by creating anti-kidney vortex pairs, which will weaken jet lift-off, caused by the kidney vortex pairs, from the primary hole. The tri-circular shaped hole will provide better film cooling effectiveness near the hole area, and is not sensitive to blowing ratio. The two-stage structure for tri-circular shaped hole provides better film coverage because it changes the flow structure inside the channel and decreases jet penetration.

Experimental and Numerical Investigations of the NEKOMIMI Film Cooling Technology

2012 ◽  
Author(s):  
Karsten Kusterer ◽  
Nurettin Tekin ◽  
Dieter Bohn ◽  
Takao Sugimoto ◽  
Ryozo Tanaka ◽  
...  
Keyword(s):  
Thermal Efficiency ◽  
Film Cooling ◽  
Gas Turbines ◽  
Mixing Processes ◽  
Cooling Effectiveness ◽  
Numerical Investigations ◽  
Hot Gas ◽  
Cooling Technology ◽  
Lift Off ◽  
Cooling Air

The improvement of the thermal efficiency of modern gas turbines can be achieved by reducing the required cooling air amount. Therefore, it is necessary to increase the cooling effectiveness, so that the available cooling air fulfils the cooling task even if the amount has been reduced. Due to experimental and numerical efforts, it is well understood today that aerodynamic mixing processes are enhanced by counter rotating vortices (CRV) in the cooling jets and lead to jet liftoff effects. Novel film cooling technologies focus on establishing anti-counter-rotating-vortices (ACRV) inside the cooling jet that prevent the hot gas from flowing underneath the jet and, thus, avoid the lift-off effect. One of these technologies is the NEKOMIMI film cooling, which is derived from the original double-jet film cooling (DJFC).

Conjugate Heat Transfer and Film Cooling of a Multi-Stage Cooling Scheme

2008 ◽  
Author(s):  
M. Ghorab ◽  
S. I. Kim ◽  
I. Hassan
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Gas Turbines ◽  
Conjugate Heat Transfer ◽  
Density Ratio ◽  
Design Parameters ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Multi Stage ◽  
Internal Gap

Cooling techniques play a key role in improving efficiency and power output of modern gas turbines. The conjugate technique of film and impingement cooling schemes is considered in this study. The Multi-Stage Cooling Scheme (MSCS) involves coolant passing from inside to outside turbine blade through two stages. The first stage; the coolant passes through first hole to internal gap where the impinging jet cools the external layer of the blade. Finally, the coolant passes through the internal gap to the second hole which has specific designed geometry for external film cooling. The effect of design parameters, such as, offset distance between two-stage holes, gap height, and inclination angle of the first hole, on upstream conjugate heat transfer rate and downstream film cooling effectiveness performance are investigated computationally. An Inconel 617 alloy with variable properties is selected for the solid material. The conjugate heat transfer and film cooling characteristics of MSCS are analyzed across blowing ratios of Br = 1 and 2 for density ratio, 2. This study presents upstream wall temperature distributions due to conjugate heat transfer for different gap design parameters. The maximum film cooling effectiveness with upstream conjugate heat transfer is less than adiabatic film cooling effectiveness by 24–34%. However, the full coverage of cooling effectiveness in spanwise direction can be obtained using internal cooling with conjugate heat transfer, whereas adiabatic film cooling effectiveness has narrow distribution.

scholarly journals State-of-the-Art Cooling Technology for a Turbine Rotor Blade

2017 ◽  
Author(s):  
Jason Town ◽  
Doug Straub ◽  
James Black ◽  
Karen Thole ◽  
Tom Shih
Keyword(s):  
Film Cooling ◽  
Gas Turbines ◽  
State Of The Art ◽  
Internal Heat ◽  
Leading Edge ◽  
Jet Impingement ◽  
Test Facility ◽  
Turbine Wheel ◽  
Baseline Design ◽  
External Cooling

Effective internal and external cooling of airfoils is key to maintaining component life for efficient gas turbines. Cooling designs have spanned the range from simple internal convective channels to more advanced double-walls with shaped film-cooling holes. This paper describes the development of an internal and external cooling concept for a state-of-the-art cooled turbine blade. These cooling concepts are based on a review of literature and patents, as well as, interactions with academic and industry turbine cooling experts. The cooling configuration selected and described in this paper is referred to as the “baseline” design, since this design will simultaneously be tested with other more advanced blade cooling designs in a rotating turbine test facility using a “rainbow turbine wheel” configuration. For the baseline design, the leading edge is cooled by internal jet impingement and showerhead film cooling. The mid-chord region of the blade contains a three-pass serpentine passage with internal discrete V-shaped trip strips to enhance the internal heat transfer coefficient. The film cooling along the mid-chord of the blade uses multiple rows of shaped diffusion holes. The trailing edge is internally cooled using jet impingement and externally film cooled through partitioned cuts on the pressure side of the blade.

Turbine Vane Endwall Film Cooling From Cross-Row Configuration With Simulated Upstream Leakage Flow

2017 ◽  
Author(s):  
Nafiz H. K. Chowdhury ◽  
Chao-Cheng Shiau ◽  
Je-Chin Han ◽  
Luzeng Zhang ◽  
Hee-Koo Moon
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Companion Paper ◽  
Leakage Flow ◽  
Blow Down ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Free Stream Turbulence ◽  
Lift Off ◽  
Endwall Cooling

The performance of a full coverage film cooling configuration called cross-row (CR) configuration including upstream inlet leakage flow was studied by measuring the adiabatic film cooling effectiveness distribution using PSP technique. Experiments were conducted in a blow-down wind tunnel cascade facility at the isentropic exit Mach number of 0.5 corresponding to inlet Reynolds number of 3.8 × 105, based on axial chord length. A free-stream turbulence level was generated as high as 19% with a length scale of 1.7 cm at the inlet. The results are presented as two-dimensional adiabatic film cooling effectiveness distributions on the endwall surface with corresponding spanwise averaged distributions. The focus of this study is to investigate the effect of coolant-to-mainstream mass flow ratio (MFR) and density ratio (DR) on the proposed endwall cooling design. Initially, increased MFR for the endwall cooling and upstream leakage levels up the local adiabatic cooling effectiveness and yields relatively uniform coverage on the entire endwall. However, in either case, highest MFR does not provide any improvement as endwall cooling suffered from the jet lift-off and leakage coolant coverage restricted by the downstream near-wall flow field. Results also indicated a density ratio of 1.5 provides the best performance. Finally, a fair comparison is made with another design called axial-row (AR) configuration from a companion paper.

Numerical Analysis on the Leading Edge Film Cooling of Bifurcation Holes for Gas Turbine Blade

2021 ◽  
Author(s):  
Zhonghao Tang ◽  
Gongnan Xie ◽  
Honglin Li ◽  
Wenjing Gao ◽  
Chunlong Tan ◽  
...  
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Turbulence Models ◽  
Leading Edge ◽  
Spanwise Direction ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Cylindrical Holes ◽  
Lift Off

Abstract Film cooling performance of the cylindrical film holes and the bifurcated film holes on the leading edge model of the turbine blade are investigated in this paper. The suitability of different turbulence models to predict local and average film cooling effectiveness is validated by comparing with available experimental results. Three rows of holes are arranged in a semi-cylindrical model to simulate the leading edge of the turbine blade. Four different film cooling structures (including a cylindrical film holes and other three different bifurcated film holes) and four different blowing ratios are studied in detail. The results show that the film jets lift off gradually in the leading edge area as the blowing ratio increases. And the trajectory of the film jets gradually deviate from the mainstream direction to the spanwise direction. The cylindrical film holes and vertical bifurcated film holes have better film cooling effectiveness at low blowing ratio while the other two transverse bifurcated film holes have better film cooling effectiveness at high blowing ratio. And the film cooling effectiveness of the transverse bifurcated film holes increase with the increasing the blowing ratio. Additionally, the advantage of transverse bifurcated holes in film cooling effectiveness is more obvious in the downstream region relative to the cylindrical holes. The Area-Average film cooling effectiveness of transverse bifurcated film holes is 38% higher than that of cylindrical holes when blowing ratio is 2.

Implementation of Hole-Pair in Ramp to Improve Film Cooling Effectiveness on a Plain Surface

2020 ◽  
Author(s):  
Sadam Hussain ◽  
Xin Yan
Keyword(s):  
Film Cooling ◽  
Gas Turbines ◽  
Density Ratio ◽  
Hole Pair ◽  
Cooling Effect ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Cooling Hole ◽  
Plain Surface

Abstract Film cooling is one of the most critical technologies in modern gas turbine engine to protect the high temperature components from erosion. It allows gas turbines to operate above the thermal limits of blade materials by providing the protective cooling film layer on outer surfaces of blade against hot gases. To get a higher film cooling effect on plain surface, current study proposes a novel strategy with the implementation of hole-pair into ramp. To gain the film cooling effectiveness on the plain surface, RANS equations combined with k-ω turbulence model were solved with the commercial CFD solver ANSYS CFX11.0. In the numerical simulations, the density ratio (DR) is fixed at 1.6, and the film cooling effect on plain surface with different configurations (i.e. with only cooling hole, with only ramp, and with hole-pair in ramp) were numerically investigated at three blowing ratios M = 0.25, 0.5, and 0.75. The results show that the configuration with Hole-Pair in Ramp (HPR) upstream the cooling hole has a positive effect on film cooling enhancement on plain surface, especially along the spanwise direction. Compared with the baseline configuration, i.e. plain surface with cylindrical hole, the laterally-averaged film cooling effectiveness on plain surface with HPR is increased by 18%, while the laterally-averaged film cooling effectiveness on plain surface with only ramp is increased by 8% at M = 0.5. As the blowing ratio M increases from 0.25 to 0.75, the laterally-averaged film cooling effectiveness on plain surface with HPR is kept on increasing. At higher blowing ratio M = 0.75, film cooling effectiveness on plain surface with HPR is about 19% higher than the configuration with only ramp.

Leading Edge Film Cooling of a Turbine Blade Model Through Single and Double Row Injection: Effects of Coolant Density

1994 ◽  
Author(s):  
M. Salcudean ◽  
I. Gartshore ◽  
K. Zhang ◽  
Y. Barnea
Keyword(s):  
Turbine Blade ◽  
Mass Flow ◽  
Film Cooling ◽  
Leading Edge ◽  
Spanwise Direction ◽  
Double Row ◽  
Cooling Effectiveness ◽  
Stagnation Line ◽  
Film Cooling Effectiveness ◽  
Staggered Arrangement

Experiments have been conducted on a large model of a turbine blade. Attention has been focussed on the leading edge region, which has a semi-circular shape and four rows of film cooling holes positioned symmetrically about the stagnation line. The cooling holes were oriented in a spanwise direction with an inclination of 30° to the surface, and had streamwise locations of ±15° and ±44° from the stagnation line. Film cooling effectiveness was measured using a heat/mass analogy. Single row cooling from the holes at 15° and 44° showed similar patterns: spanwise averaged effectiveness which rises from zero at zero coolant mass flow to a maximum value η* at some value of mass flow ratio M*, then drops to low values of η at higher M. The trends can be quantitatively explained from simple momentum considerations for either air or CO2 as the coolant gas. Close to the holes, air provides higher η values for small M. At higher M, particularly farther downstream, the CO2 may be superior. The use of an appropriately defined momentum ratio G collapses the data from both holes using either CO2 or air as coolant onto a single curve. For η*, the value of G for all data is about 0.1. Double row cooling with air as coolant shows that the relative stagger of the two rows is an important parameter. Holes in line with each other in successive rows can provide improvements in spanwise averaged film cooling effectiveness of as much as 100% over the common staggered arrangement. This improvement is due to the interaction between coolant from rows one and two, which tends to provide complete coverage of the downstream surface when the rows are placed correctly with respect to each other.

Sign in / Sign up

Export Citation Format

Share Document