Numerical Study on Effects of Jet Nozzle Angle and Number on Vortex Cooling Behavior for Gas Turbine Blade Leading Edge

2016 ◽  
Author(s):  
Changhe Du ◽  
Liang Li ◽  
XiuXiu Chen ◽  
Xiaojun Fan ◽  
Zhenping Feng
Keyword(s):  
Heat Transfer ◽  
Turbulence Model ◽  
Pressure Loss ◽  
Total Pressure ◽  
Static Pressure ◽  
Pressure Ratio ◽  
Total Pressure Loss ◽  
Upstream Region ◽  
Loss Ratio ◽  
Jet Nozzle

Vortex cooling is a promising blade cooling technique for its excellent heat transfer and pressure loss control behavior. In this paper, the proper vortex chamber model is utilized for vortex cooling mechanism analysis. Three dimensional viscous steady Reynolds Averaged Navier-Stokes (RANS) equations are adopted to explore the influences of jet nozzle angle and number on vortex cooling flow and thermal performance. Turbulence model verification and grid independence analysis are conducted to determine the suitable turbulence model and mesh number for calculations. Results show that due to obvious mass flux enhancement downstream, stronger axial impact effect will generate, leading to the high Nusselt number region downstream deflection towards outlet. As jet nozzle angle increases from α=60° to α=120°, the static pressure ratio increases for the upstream region and decreases for the downstream region, and the total pressure loss ratio increases. The rotation movement and heat transfer intensity will decrease when jet nozzle angle changes away from α=90°. The air jetting velocity decreases and the static pressure ratio increases with the increasing jet nozzle number. When jet nozzle angle increases from 1 to 11, the total pressure loss ratio decreases and the heat transfer intensity increases at first and then decreases.

scholarly journals Accurate 2-D Modelling of Transonic Compressor Cascade Aerodynamics

Aerospace ◽  
2019 ◽  
Vol 6 (5) ◽  
pp. 57 ◽  
Author(s):  
Tommaso Piovesan ◽  
Andrea Magrini ◽  
Ernesto Benini
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Static Pressure ◽  
Pressure Ratio ◽  
Loss Coefficient ◽  
Total Pressure Loss ◽  
Compressor Cascade ◽  
Transonic Compressor ◽  
Pressure Loss Coefficient ◽  
Total Pressure Loss Coefficient

Modern aeronautic fans are characterised by a transonic flow regime near the blade tip. Transonic cascades enable higher pressure ratios by a complex system of shockwaves arising across the blade passage, which has to be correctly reproduced in order to predict the performance and the operative range. In this paper, we present an accurate two-dimensional numerical modelling of the ARL-SL19 transonic compressor cascade. A large series of data from experimental tests in supersonic wind tunnel facilities has been used to validate a computational fluid dynamic model, in which the choice of turbulence closure resulted critical for an accurate reproduction of shockwave-boundary layer interaction. The model has been subsequently employed to carry out a parametric study in order to assess the influence of main flow variables (inlet Mach number, static pressure ratio) and geometric parameters (solidity) on the shockwave pattern and exit status. The main objectives of the present work are to perform a parametric study for investigating the effects of the abovementioned variables on the cascade performance, in terms of total-pressure loss coefficient, and on the shockwave pattern and to provide a quite large series of data useful for a preliminary design of a transonic compressor rotor section. After deriving the relation between inlet and exit quantities, peculiar to transonic compressors, exit Mach number, mean exit flow angle and total-pressure loss coefficient have been examined for a variety of boundary conditions and parametrically linked to inlet variables. Flow visualisation has been used to describe the shock-wave pattern as a function of the static pressure ratio. Finally, the influence of cascade solidity has been examined, showing a potential reduction of total-pressure loss coefficient by employing a higher solidity, due to a significant modification of shockwave system across the cascade.

scholarly journals Investigation of the Effects of Different Working Fluids on Compressor Cascade Performance

2021 ◽  
Vol 11 (5) ◽  
pp. 1989
Author(s):  
Zhitao Tian ◽  
Chengze Wang ◽  
Qun Zheng
Keyword(s):  
Physical Properties ◽  
Specific Heat ◽  
Pressure Loss ◽  
Total Pressure ◽  
Static Pressure ◽  
Pressure Ratio ◽  
Total Pressure Loss ◽  
Compressor Cascade ◽  
Working Fluids ◽  
Specific Heat Ratio

The compressor of closed Brayton cycle (CBC) plant operating with working fluid other than air is a vital element of the energy conversion unit. However, due to insufficient understanding of the influence of the physical properties of working fluids on the performance of the compressor, the actual working conditions and design conditions of the compressor’s performance deviate greatly. In this paper, the objective is to analyze the influence mechanism of the physical properties on the performance of the cascade of compressor (static pressure ratio and total pressure loss coefficient). Therefore, the impact of a specific heat ratio on the performance of the compressor cascade is studied utilizing carbon dioxide (γ = 1.29), air and carbon monoxide (γ = 1.4), argon and helium (γ = 1.667). Moreover, the relationships of static pressure ratio and total pressure loss coefficient with physical properties of the working fluids are analyzed in the compressor cascade. It is established that a higher specific heat ratio fluid gives a higher coefficient of total pressure loss and static pressure ratio in contrast to smaller specific heat ratio at matching inlet Reynolds number and Mach number.

Computation of Shocked Flows in Compressor Cascades

1972 ◽  
Author(s):  
S. Gopalakrishnan ◽  
R. Bozzola
Keyword(s):  
Asymptotic Solution ◽  
Pressure Loss ◽  
Total Pressure ◽  
Static Pressure ◽  
Numerical Technique ◽  
Pressure Ratio ◽  
Physical Problem ◽  
Total Pressure Loss ◽  
Time Dependent ◽  
Dependent Form

A numerical technique is presented for the calculation of shocked flows in compressor cascades. The problem is posed in the time-dependent form and the asymptotic solution at large times provides the solution of the steady physical problem. The solutions exhibit the formation and movement of shocks as the static pressure ratio across the cascade is varied. The resulting inlet and outlet angles and total pressure loss are also shown.

Conjugate Heat Transfer Characteristics of Double Wall Cooling With Gradient Diameter of Film and Impingement Holes

2021 ◽  
Author(s):  
Juan He ◽  
Qinghua Deng ◽  
Zhenping Feng
Keyword(s):  
Heat Transfer ◽  
Pressure Loss ◽  
Total Pressure ◽  
Flow Direction ◽  
Turbine Blades ◽  
Total Pressure Loss ◽  
Advanced Technique ◽  
Cooling Effectiveness ◽  
Uniform Pattern ◽  
Double Wall

Abstract Double wall cooling, consisting of internal impingement cooling and external film cooling, is believed to be the most advanced technique in modern turbine blades cooling. In this paper, to improve the uniformity of temperature distribution, a flat plate double wall cooling model with gradient diameter of film and impingement holes was proposed, and the heat transfer and flow characteristics were investigated by solving steady three-dimensional Reynolds-Averaged Navier-Stokes (RANS) equations with SST k-ω turbulence model. The influence of gradient diameter on overall cooling effectiveness and total pressure loss was studied by comparing with the uniform pattern at the blowing ratios ranging from 0.5 to 2. For gradient diameter of film hole patterns, results show that −10% film pattern always has the lowest film flow non-uniformity coefficient. The laterally averaged overall cooling effectiveness of uniform pattern lies between that of +10% and −10% film patterns, but the intersection of three patterns moves upstream from the middle of flow direction with the increase of blowing ratio. Therefore, the −10% film pattern exerts the highest area averaged cooling effectiveness, which is improved by up to 1.6% and 1% at BR = 0.5 and 1 respectively compared with a uniform pattern. However, at higher blowing ratios, the +10% film pattern maintains higher cooling effectiveness and lower total pressure loss. For gradient diameter of impingement hole patterns, the intersection of laterally averaged overall cooling effectiveness in three patterns is located near the middle of flow direction under all blowing ratios. The uniform pattern has the highest area averaged cooling effectiveness and the smallest non-uniform coefficient, but the −10% jet pattern has advantages of reducing pressure loss, especially in the laminated loss.

Second Vane Total Pressure Loss Due to Endwall Iceform Contouring

2008 ◽  
Author(s):  
Ronald S. LaFleur
Keyword(s):  
Heat Transfer ◽  
Secondary Flow ◽  
Pressure Loss ◽  
Total Pressure ◽  
Aerodynamic Drag ◽  
Pressure Coefficient ◽  
Secondary Flows ◽  
Total Pressure Loss ◽  
Surface Shape ◽  
Exit Plane

The iceformation design method generates an endwall contour, altering the secondary flows that produce elevated endwall heat transfer load and total pressure losses. Iceformation is an analog to regions of metal melting where a hot fluid alters the isothermal surface shape of a part as it is maintained by a cooling fluid. The passage flow, heat transfer and geometry evolve together under the constraints of flow and thermal boundary conditions. The iceformation concept is not media dependent and can be used in analogous flows and materials to evolve novel boundary shapes. In the past, this method has been shown to reduce aerodynamic drag and total pressure loss in flows such as diffusers and cylinder/endwall junctures. A prior paper [1] showed that the Reynolds number matched iceform geometry had a 24% lower average endwall heat transfer than the rotationally symmetric endwall geometry of the Energy Efficiency Engine (E3). Comparisons were made between three endwall geometries: the ‘iceform’, the ‘E3’ and the ‘flat’ as a limiting case of the endwall design space. This paper adds to the iceformation design record by reporting the endwall aerodynamic performances. Second vane exit flow velocities and pressures were measured using an automated 2-D traverse of a 1.2 mm diameter five-hole probe. Exit plane maps for the three endwall geometries are presented showing the details of the total pressure coefficient contours and the velocity vectors. The formation of secondary flow vortices is shown in the exit plane and this results in an impact on exit plane total pressure loss distribution, off-design over- and under-turning of the exit flow. The exit plane contours are integrated to form overall measures of the total pressure loss. Relative to the E3 endwall, the iceform endwall has a slightly higher total pressure loss attributed to higher dissipation of the secondary flow within the passage. The iceform endwall has a closer-to-design exit flow pattern than the E3 endwall.

The Influence of Aero-Derivative Combustor Turbulence and Reynolds Number on Vane Aerodynamics Losses, Secondary Flows, and Wake Growth

2006 ◽  
Author(s):  
F. E. Ames ◽  
J. D. Johnson ◽  
N. J. Fiala
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Pressure Loss ◽  
Total Pressure ◽  
Reynolds Numbers ◽  
Secondary Flows ◽  
Total Pressure Loss ◽  
Surface Boundary ◽  
High Turbulence ◽  
Turbulence Condition

Exit surveys detailing total pressure loss, turning angle, and secondary velocities have been acquired for a fully loaded vane profile in a large scale low speed cascade facility. Exit surveys have been taken over a four-to-one range in Reynolds numbers based on exit conditions and for both a low turbulence condition and a high turbulence condition. The high turbulence condition was generated using a mock aero-derivative combustor. Exit loss, angle, and secondary velocity measurements were acquired in the facility using a five-hole cone probe at two stations representing axial chord spacings of 0.25 and 0.50. Substantial differences in the level of losses, distribution of losses, and secondary flow vectors are seen with the different turbulence conditions and at the different Reynolds numbers. The higher turbulence condition produces a significantly broader wake than the low turbulence case and shows a measurable total pressure loss in the region outside the wakes. Generally, total pressure losses are about 0.02 greater for the high turbulence case compared with the low turbulence case primarily due to the state of the suction surface boundary layers. Losses decrease moderately with increasing Reynolds number. Cascade inlet velocity distributions have been previously documented in an endwall heat transfer study of this same geometry. These exit survey measurements support our understanding of the endwall heat transfer distributions, the secondary flows in the passage, and the origin of losses.

Heat Transfer Enhancement for Gas Turbine Blade Leading Edge Cooling Using Curved Double-Wall/Vortex Cooling With Various Disturbing Objects

2019 ◽  
Author(s):  
Xiaojun Fan ◽  
Liang Li ◽  
Jiefeng Wang ◽  
Fan Wu
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Pressure Loss ◽  
Total Pressure ◽  
Leading Edge ◽  
Total Pressure Loss ◽  
Wall Impingement ◽  
Pin Fins ◽  
Cooling Passage ◽  
Double Wall

Abstract A new double-wall cooling configuration combined with the vortex cooling is established to study the cooling behavior for the gas turbine blade leading edge. This configuration consists of multiple nozzles, a curved inner cooling passage, a row of bridge holes and a curved outer cooling passage with 4 kinds of disturbing objects (namely smooth wall, pin-fins, dimples and protrusions). Numerical simulations are performed based on the 3D viscous steady Reynolds Averaged Navier-Stokes (RANS) equations and the k-ω turbulence model. The cooling behavior of the Double-wall/vortex cooling configuration is compared with the Double-wall/impingement cooling configuration at the same conditions. Generally, the Double-wall/vortex cooling configuration has a better cooling performance. It is found the Nusselt number of the inner surface for the Double-wall/vortex cooling configuration is 46.7% higher. However, the Double-wall/impingement cooling configuration has a smaller friction coefficient and a total pressure loss. Different disturbing objects have significant influences on the heat transfer performance of the outer surface. The Nusselt number of disturbing objects (pin-fins, dimples and protrusions) is much higher than the smooth wall, and the value is 1.27–2.22 times larger. Configuration with protrusions has the highest globally-averaged Nusselt number. For the heat transfer performance of the inner surface and the total pressure loss coefficient, disturbing objects have no obvious influence. As bridge holes row increases, the overall cooling performance is improved. The globally-averaged Nusselt number of the outer target is enhanced while the total pressure loss is reduced.

Secondary Flow Control Using Vortex Generator Jets

2004 ◽  
Vol 126 (4) ◽  
pp. 650-657 ◽  
Author(s):  
R. K. Sullerey ◽  
A. M. Pradeep
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Static Pressure ◽  
Vortex Generator ◽  
Control Flow ◽  
Secondary Flows ◽  
Total Pressure Loss ◽  
Vortex Generators ◽  
Vortex Generator Jets ◽  
Inflow Conditions

In this paper, results are presented of an experimental investigation into the effectiveness of vortex generator jets in controlling secondary flows in two-dimensional S-duct diffusers. The experiments were performed in uniform and distorted inflow conditions and the performance evaluation of the diffuser was carried out in terms of static pressure recovery and quality of the exit flow. In the case with inflow distortion, tapered fin vortex generators were employed in addition to vortex generator jets to control flow separation that was detected on the wall with inflow distortion. Detailed measurements including total pressure, velocity distribution, surface static pressure, skin friction, and boundary layer measurements were taken at a Reynolds number of 7.8×105. These results are presented in terms of static pressure rise, distortion coefficient, and total pressure loss coefficient at the duct exit. For uniform inflow, the use of vortex generator jets resulted in more than a 30 percent decrease in total pressure loss and flow distortion coefficients. In combination with passive device (tapered fin vortex generators), the vortex generator jets reduce total pressure losses by about 25 percent for distorted inflow conditions. A potential application of this method may include control of secondary flows in turbo machinery.

Flow Investigation Through a 30° Turn Diffusing Duct in Subsonic Flow Regime

2009 ◽  
Author(s):  
Prasanta K. Sinha ◽  
Biswajit Haldar ◽  
Amar N. Mullick ◽  
Bireswar Majumdar
Keyword(s):  
Axial Velocity ◽  
Pressure Loss ◽  
Total Pressure ◽  
High Speed ◽  
Static Pressure ◽  
Transverse Velocity ◽  
Total Pressure Loss ◽  
Pressure Recovery ◽  
Pressure Probe ◽  
Mean Velocity

Curved diffusers are an integral component of the gas turbine engines of high-speed aircraft. These facilitate effective operation of the combustor by reducing the total pressure loss. The performance characteristics of these diffusers depend on their geometry and the inlet conditions. In the present investigation the distribution of axial velocity, transverse velocity, mean velocity, static and total pressures are experimentally studied on a curved diffuser of 30° angle of turn with an area ratio of 1.27. The centreline length was chosen as three times of inlet diameter. The experimental results then were numerically validated with the help of Fluent, the commercial CFD software. The measurements of axial velocity, transverse velocity, mean velocity, static pressure and total pressure distribution were taken at Reynolds number 1.9 × 105 based on inlet diameter and mass average inlet velocity. The mean velocity and all the three components of mean velocity were measured with the help of a pre-calibrated five-hole pressure probe. The velocity distribution shows that the flow is symmetrical and uniform at the inlet and exit sections and high velocity cores are accumulated at the top concave surface due to the combined effect of velocity diffusion and centrifugal action. It also indicates the possible development of secondary motions between the concave and convex walls of the test diffuser. The mass average static pressure recovery and total pressure loss within the curved diffuser increases continuously from inlet to exit and they attained maximum values of 35% and 14% respectively. A comparison between the experimental and predicated results shows a good qualitative agreement between the two. Standard k-ε model in Fluent solver was chosen for validation. It has been observed that coefficient of pressure recovery Cpr for the computational investigation was obtained as 38% compared to the experimental investigation which was 35% and the coefficient of pressure loss is obtained as 13% in computation investigation compared to the 14% in experimental study, which indicates a very good qualitative matching.

Experimental investigation of the role of struts in high speed mixing

2013 ◽  
Vol 117 (1188) ◽  
pp. 193-211 ◽  
Author(s):  
S. L. N. Desikan ◽  
J. Kurian
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
High Speed ◽  
Static Pressure ◽  
Mie Scattering ◽  
Total Pressure Loss ◽  
Pressure Losses ◽  
Mixing Performance ◽  
Supersonic Mixing

AbstractThis paper presents the experimental results of the role of struts in supersonic mixing. Experiments were carried out with novel strut configurations to show their capabilities on mixing with reasonable total pressure losses. The performances were compared with the Baseline Strut configurations (BSPI and BSNI). The analysis presented includes the mixing quantifications using Mie scattering signature, flow field visualisation, measurement of wall static pressure and the total pressure loss calculations. The results clearly demonstrated that the proposed strut configurations achieved increased mixing (7-8%) compared to BSPI with increase in total pressure loss (2%). On the other hand, when compared with BSNI, the mixing performance was found to be decreased by 6% with reduced total pressure loss (12%).

Sign in / Sign up

Export Citation Format

Share Document