scholarly journals Investigation of the Effects of Different Working Fluids on Compressor Cascade Performance

2021 ◽  
Vol 11 (5) ◽  
pp. 1989
Author(s):  
Zhitao Tian ◽  
Chengze Wang ◽  
Qun Zheng
Keyword(s):  
Physical Properties ◽  
Specific Heat ◽  
Pressure Loss ◽  
Total Pressure ◽  
Static Pressure ◽  
Pressure Ratio ◽  
Total Pressure Loss ◽  
Compressor Cascade ◽  
Working Fluids ◽  
Specific Heat Ratio

The compressor of closed Brayton cycle (CBC) plant operating with working fluid other than air is a vital element of the energy conversion unit. However, due to insufficient understanding of the influence of the physical properties of working fluids on the performance of the compressor, the actual working conditions and design conditions of the compressor’s performance deviate greatly. In this paper, the objective is to analyze the influence mechanism of the physical properties on the performance of the cascade of compressor (static pressure ratio and total pressure loss coefficient). Therefore, the impact of a specific heat ratio on the performance of the compressor cascade is studied utilizing carbon dioxide (γ = 1.29), air and carbon monoxide (γ = 1.4), argon and helium (γ = 1.667). Moreover, the relationships of static pressure ratio and total pressure loss coefficient with physical properties of the working fluids are analyzed in the compressor cascade. It is established that a higher specific heat ratio fluid gives a higher coefficient of total pressure loss and static pressure ratio in contrast to smaller specific heat ratio at matching inlet Reynolds number and Mach number.

scholarly journals Accurate 2-D Modelling of Transonic Compressor Cascade Aerodynamics

Aerospace ◽  
2019 ◽  
Vol 6 (5) ◽  
pp. 57 ◽  
Author(s):  
Tommaso Piovesan ◽  
Andrea Magrini ◽  
Ernesto Benini
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Static Pressure ◽  
Pressure Ratio ◽  
Loss Coefficient ◽  
Total Pressure Loss ◽  
Compressor Cascade ◽  
Transonic Compressor ◽  
Pressure Loss Coefficient ◽  
Total Pressure Loss Coefficient

Modern aeronautic fans are characterised by a transonic flow regime near the blade tip. Transonic cascades enable higher pressure ratios by a complex system of shockwaves arising across the blade passage, which has to be correctly reproduced in order to predict the performance and the operative range. In this paper, we present an accurate two-dimensional numerical modelling of the ARL-SL19 transonic compressor cascade. A large series of data from experimental tests in supersonic wind tunnel facilities has been used to validate a computational fluid dynamic model, in which the choice of turbulence closure resulted critical for an accurate reproduction of shockwave-boundary layer interaction. The model has been subsequently employed to carry out a parametric study in order to assess the influence of main flow variables (inlet Mach number, static pressure ratio) and geometric parameters (solidity) on the shockwave pattern and exit status. The main objectives of the present work are to perform a parametric study for investigating the effects of the abovementioned variables on the cascade performance, in terms of total-pressure loss coefficient, and on the shockwave pattern and to provide a quite large series of data useful for a preliminary design of a transonic compressor rotor section. After deriving the relation between inlet and exit quantities, peculiar to transonic compressors, exit Mach number, mean exit flow angle and total-pressure loss coefficient have been examined for a variety of boundary conditions and parametrically linked to inlet variables. Flow visualisation has been used to describe the shock-wave pattern as a function of the static pressure ratio. Finally, the influence of cascade solidity has been examined, showing a potential reduction of total-pressure loss coefficient by employing a higher solidity, due to a significant modification of shockwave system across the cascade.

Experimental and Numerical Investigations of Pressure Loss and 3-D Flow Separations in a Linear Compressor Cascade

2019 ◽  
Author(s):  
Saeed A. El-Shahat ◽  
Hesham M. El-Batsh ◽  
Ali M. A. Attia ◽  
Guojun Li ◽  
Lei Fu
Keyword(s):  
Flow Field ◽  
Flow Separation ◽  
Pressure Loss ◽  
Total Pressure ◽  
Static Pressure ◽  
Axial Compressor ◽  
Total Pressure Loss ◽  
Compressor Cascade ◽  
Loss Mechanism ◽  
Linear Compressor Cascade

Abstract Flow separation is a major parameter affecting the compressor performance. It reduces the compressor efficiency, limits static pressure rise capability and contributes to instability in compressors. In applied research, there is a lack of understanding of the nature and mechanism of the three-dimensional (3-D) flow separation in the axial compressor especially on the juncture of the endwall and blade corner region. In the present study, the 3-D flow field in an axial compressor cascade has been studied experimentally as well as numerically. For the experimental study part, a linear compressor cascade has been installed in an open loop wind tunnel. The experimental data was acquired for a Reynolds number Rec = 2.98 × 105 based on the blade chord and the inlet flow conditions. The total pressure loss progress through the blade passage has been measured by using calibrated five and seven-hole pressure probes connected to ATX sensor module data acquisition system. The static pressure distribution on the endwall has been measured employing static pressure taps connected to digital micromanometers. To investigate the loss mechanism through the cascade, the total pressure loss coefficient has been calculated from the measured data. The computational fluid dynamics (CFD) study of the flow field was performed to gain a better understanding of the flow features. Two turbulence models, Spalart-Allmaras (S-A) and shear stress transport SST (k-ω) were used. From both parts of study, the flow field development and total pressure loss progress through the cascade have been investigated and compared. Moreover, the received data demonstrated a good agreement between the experimental and computational results. The predicted flow streamlines by numerical calculations showed regions characterized by flow separation and recirculation zones that could be used to enhance the understanding of the loss mechanism in compressor cascades. All measurements taken by 5-hole and 7-hole pressure probes have been analyzed and compared. It was found that their readings were almost the same and there are no excellences for using 7-hole probe. Furthermore S-A turbulence model calculations showed more consistencies with experimental results than SST (k-ω) model.

Computation of Shocked Flows in Compressor Cascades

1972 ◽  
Author(s):  
S. Gopalakrishnan ◽  
R. Bozzola
Keyword(s):  
Asymptotic Solution ◽  
Pressure Loss ◽  
Total Pressure ◽  
Static Pressure ◽  
Numerical Technique ◽  
Pressure Ratio ◽  
Physical Problem ◽  
Total Pressure Loss ◽  
Time Dependent ◽  
Dependent Form

A numerical technique is presented for the calculation of shocked flows in compressor cascades. The problem is posed in the time-dependent form and the asymptotic solution at large times provides the solution of the steady physical problem. The solutions exhibit the formation and movement of shocks as the static pressure ratio across the cascade is varied. The resulting inlet and outlet angles and total pressure loss are also shown.

Numerical Study on Effects of Jet Nozzle Angle and Number on Vortex Cooling Behavior for Gas Turbine Blade Leading Edge

2016 ◽  
Author(s):  
Changhe Du ◽  
Liang Li ◽  
XiuXiu Chen ◽  
Xiaojun Fan ◽  
Zhenping Feng
Keyword(s):  
Heat Transfer ◽  
Turbulence Model ◽  
Pressure Loss ◽  
Total Pressure ◽  
Static Pressure ◽  
Pressure Ratio ◽  
Total Pressure Loss ◽  
Upstream Region ◽  
Loss Ratio ◽  
Jet Nozzle

Vortex cooling is a promising blade cooling technique for its excellent heat transfer and pressure loss control behavior. In this paper, the proper vortex chamber model is utilized for vortex cooling mechanism analysis. Three dimensional viscous steady Reynolds Averaged Navier-Stokes (RANS) equations are adopted to explore the influences of jet nozzle angle and number on vortex cooling flow and thermal performance. Turbulence model verification and grid independence analysis are conducted to determine the suitable turbulence model and mesh number for calculations. Results show that due to obvious mass flux enhancement downstream, stronger axial impact effect will generate, leading to the high Nusselt number region downstream deflection towards outlet. As jet nozzle angle increases from α=60° to α=120°, the static pressure ratio increases for the upstream region and decreases for the downstream region, and the total pressure loss ratio increases. The rotation movement and heat transfer intensity will decrease when jet nozzle angle changes away from α=90°. The air jetting velocity decreases and the static pressure ratio increases with the increasing jet nozzle number. When jet nozzle angle increases from 1 to 11, the total pressure loss ratio decreases and the heat transfer intensity increases at first and then decreases.

Endwall Contouring and Fillet Design for Reducing Losses and Homogenizing the Outflow of a Compressor Cascade

2014 ◽  
Author(s):  
Oliver Reutter ◽  
Stefan Hemmert-Pottmann ◽  
Alexander Hergt ◽  
Eberhard Nicke
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Leading Edge ◽  
Total Pressure Loss ◽  
Wall Region ◽  
Optimized Design ◽  
Compressor Cascade ◽  
Outflow Region ◽  
Endwall Contouring ◽  
Operating Points

The following paper deals with the development of an optimized fillet and an endwall contour for reducing the total pressure loss and for homogenizing the outflow of a highly loaded cascade with a low aspect ratio. The NACA-65 K48 cascade profile without a fillet and without endwall contouring is used as a basis. Optimizations are performed using the DLR in-house tool AutoOpti and the RANS-solver TRACE. Three operating points at an inflow Mach number of 0.67 with different inflow angles are used to secure a wide operating range of the optimized design. At first only a fillet is optimized. The optimized fillet is small at the leading edge and rather high, wide and thick towards the trailing edge. It reduces the total pressure loss and homogenizes the outflow up to a blade height of 20 %. Following this a combined optimization of the endwall and the fillet is performed. The optimized contour leads to the development of a vortex, which changes the secondary flow in such a way, that the corner separation is reduced, which in turn significantly reduces the total pressure loss up to 16 % in the design operating point. The contour in the outflow region leads to a significant homogenization of the outflow in the near wall region.

Secondary Flow Control Using Vortex Generator Jets

2004 ◽  
Vol 126 (4) ◽  
pp. 650-657 ◽  
Author(s):  
R. K. Sullerey ◽  
A. M. Pradeep
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Static Pressure ◽  
Vortex Generator ◽  
Control Flow ◽  
Secondary Flows ◽  
Total Pressure Loss ◽  
Vortex Generators ◽  
Vortex Generator Jets ◽  
Inflow Conditions

In this paper, results are presented of an experimental investigation into the effectiveness of vortex generator jets in controlling secondary flows in two-dimensional S-duct diffusers. The experiments were performed in uniform and distorted inflow conditions and the performance evaluation of the diffuser was carried out in terms of static pressure recovery and quality of the exit flow. In the case with inflow distortion, tapered fin vortex generators were employed in addition to vortex generator jets to control flow separation that was detected on the wall with inflow distortion. Detailed measurements including total pressure, velocity distribution, surface static pressure, skin friction, and boundary layer measurements were taken at a Reynolds number of 7.8×105. These results are presented in terms of static pressure rise, distortion coefficient, and total pressure loss coefficient at the duct exit. For uniform inflow, the use of vortex generator jets resulted in more than a 30 percent decrease in total pressure loss and flow distortion coefficients. In combination with passive device (tapered fin vortex generators), the vortex generator jets reduce total pressure losses by about 25 percent for distorted inflow conditions. A potential application of this method may include control of secondary flows in turbo machinery.

Location Effect of Boundary Layer Suction on Compressor Hub-Corner Separation

2014 ◽  
Author(s):  
Ping-Ping Chen ◽  
Wei-Yang Qiao ◽  
Karsten Liesner ◽  
Robert Meyer
Keyword(s):  
Boundary Layer ◽  
Pressure Loss ◽  
Total Pressure ◽  
Three Dimensional ◽  
Base Flow ◽  
Total Pressure Loss ◽  
Compressor Cascade ◽  
Suction Surface ◽  
Corner Separation ◽  
Boundary Layer Suction

The large secondary flow area in the compressor hub-corner region usually leads to three-dimensional separation in the passage with large amounts of total pressure loss. In this paper numerical simulations of a linear high-speed compressor cascade, consisting of five NACA 65-K48 stator profiles, were performed to analyze the flow mechanism of hub-corner separation for the base flow. Experimental validation is used to verify the numerical results. Active control of the hub-corner separation was investigated by using boundary layer suction. The influence of the selected locations of the endwall suction slot was investigated in an effort to quantify the gains of the compressor cascade performance. The results show that the optimal chordwise location should contain the development section of the three-dimensional corner separation downstream of the 3D corner separation onset. The best pitchwise location should be close enough to the vanes’ suction surface. Therefore the optimal endwall suction location is the MTE slot, the one from 50% to 75% chord at the hub, close to the blade suction surface. By use of the MTE slot with 1% suction flow ratio, the total-pressure loss is substantially decreased by about 15.2% in the CFD calculations and 9.7% in the measurement at the design operating condition.

Flow Investigation Through a 30° Turn Diffusing Duct in Subsonic Flow Regime

2009 ◽  
Author(s):  
Prasanta K. Sinha ◽  
Biswajit Haldar ◽  
Amar N. Mullick ◽  
Bireswar Majumdar
Keyword(s):  
Axial Velocity ◽  
Pressure Loss ◽  
Total Pressure ◽  
High Speed ◽  
Static Pressure ◽  
Transverse Velocity ◽  
Total Pressure Loss ◽  
Pressure Recovery ◽  
Pressure Probe ◽  
Mean Velocity

Curved diffusers are an integral component of the gas turbine engines of high-speed aircraft. These facilitate effective operation of the combustor by reducing the total pressure loss. The performance characteristics of these diffusers depend on their geometry and the inlet conditions. In the present investigation the distribution of axial velocity, transverse velocity, mean velocity, static and total pressures are experimentally studied on a curved diffuser of 30° angle of turn with an area ratio of 1.27. The centreline length was chosen as three times of inlet diameter. The experimental results then were numerically validated with the help of Fluent, the commercial CFD software. The measurements of axial velocity, transverse velocity, mean velocity, static pressure and total pressure distribution were taken at Reynolds number 1.9 × 105 based on inlet diameter and mass average inlet velocity. The mean velocity and all the three components of mean velocity were measured with the help of a pre-calibrated five-hole pressure probe. The velocity distribution shows that the flow is symmetrical and uniform at the inlet and exit sections and high velocity cores are accumulated at the top concave surface due to the combined effect of velocity diffusion and centrifugal action. It also indicates the possible development of secondary motions between the concave and convex walls of the test diffuser. The mass average static pressure recovery and total pressure loss within the curved diffuser increases continuously from inlet to exit and they attained maximum values of 35% and 14% respectively. A comparison between the experimental and predicated results shows a good qualitative agreement between the two. Standard k-ε model in Fluent solver was chosen for validation. It has been observed that coefficient of pressure recovery Cpr for the computational investigation was obtained as 38% compared to the experimental investigation which was 35% and the coefficient of pressure loss is obtained as 13% in computation investigation compared to the 14% in experimental study, which indicates a very good qualitative matching.

Experimental investigation of the role of struts in high speed mixing

2013 ◽  
Vol 117 (1188) ◽  
pp. 193-211 ◽  
Author(s):  
S. L. N. Desikan ◽  
J. Kurian
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
High Speed ◽  
Static Pressure ◽  
Mie Scattering ◽  
Total Pressure Loss ◽  
Pressure Losses ◽  
Mixing Performance ◽  
Supersonic Mixing

AbstractThis paper presents the experimental results of the role of struts in supersonic mixing. Experiments were carried out with novel strut configurations to show their capabilities on mixing with reasonable total pressure losses. The performances were compared with the Baseline Strut configurations (BSPI and BSNI). The analysis presented includes the mixing quantifications using Mie scattering signature, flow field visualisation, measurement of wall static pressure and the total pressure loss calculations. The results clearly demonstrated that the proposed strut configurations achieved increased mixing (7-8%) compared to BSPI with increase in total pressure loss (2%). On the other hand, when compared with BSNI, the mixing performance was found to be decreased by 6% with reduced total pressure loss (12%).

Active Separation Control in Circular and Transitioning S-Duct Diffusers Using Vortex Generator Jets

2006 ◽  
Author(s):  
A. M. Pradeep ◽  
R. K. Sullerey
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Static Pressure ◽  
Vortex Generator ◽  
Loss Coefficient ◽  
Total Pressure Loss ◽  
Separation Control ◽  
Pressure Loss Coefficient ◽  
Distortion Coefficient ◽  
Total Pressure Loss Coefficient

Performance enhancement of three-dimensional S-duct diffusers by separation control using vortex generator jets is the objective of the current experimental investigation. Two different diffuser geometries namely, a circular diffuser and a rectangular–to–circular transitioning diffuser were studied in uniform inflow conditions at a Reynolds number of 7.8 × 105 and the performance evaluation of the diffusers was carried out in terms of static pressure improvement and quality (flow uniformity) of the exit flow. Detailed measurements that included total pressure, velocity distribution, surface static pressure, skin friction and boundary layer measurements were taken and these results are presented here in terms of static pressure rise, distortion coefficient and total pressure loss coefficient at the duct exit. The mass flow rate of the air injected through the VGJ was about 0.06 percent of the main flow for separation control. The distortion coefficient reduced by over 25 percent and the total pressure loss coefficient reduced by about 30 percent in both the diffusers. The physical mechanism of the flow control devices used has been explored using smoke visualization images.

Sign in / Sign up

Export Citation Format

Share Document