Gas Dynamic Simulation of Shockless Explosion Combustion for Gas Turbine Power Cycles

2017 ◽  
Author(s):  
T. S. Rähse ◽  
C. O. Paschereit ◽  
P. Stathopoulos ◽  
P. Berndt ◽  
R. Klein
Keyword(s):  
Gas Turbine ◽  
Thermal Efficiency ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Inlet Temperature ◽  
Power Cycles ◽  
Total Enthalpy ◽  
Gas Dynamic ◽  
Turbine Inlet ◽  
Homogeneous Combustion

With the ongoing stagnation of the progress towards higher efficiency gas turbines, alternative approaches in combustion receive more attention than ever before. Besides, increasing efficiency and reducing emissions at the same time has become a first priority of the industry in the last few decades. Constant volume combustion is considered a technology capable of achieving a significant increase in thermal efficiency when applied in gas turbines. In this work, models of gas turbine cycles with two different combustion methods, being a shockless explosion combustion and an isobaric homogeneous combustion, will be simulated and compared. A code based on the one dimensional Euler equations is utilized to calculate the exhaust gas outlet parameters of the shockless explosion combustion chamber, while taking into account all the gas dynamic phenomena in it. The efficiency of the turbine is computed by steady state operational maps. The simulations provide numerous detailed results with a focus on the dependency of the SEC cycle’s thermal efficiency to the compressor pressure ratio and the turbine inlet temperature. Evaluating the kinetic energy in the total enthalpy of the turbine inlet flow is also an essential investigation.

Proposal of Innovative Gas Turbine Combined Cycle Power Generation System

2004 ◽  
Author(s):  
Hideto Moritsuka
Keyword(s):  
Power Generation ◽  
Gas Turbine ◽  
Thermal Efficiency ◽  
Pressure Ratio ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Generation System ◽  
Turbine Inlet Temperature ◽  
Turbine Inlet ◽  
Power Generation System

In order to estimate the possibility to improve thermal efficiency of power generation use gas turbine combined cycle power generation system, benefits of employing the advanced gas turbine technologies proposed here have been made clear based on the recently developed 1500C-class steam cooling gas turbine and 1300C-class reheat cycle gas turbine combined cycle power generation systems. In addition, methane reforming cooling method and NO reducing catalytic reheater are proposed. Based on these findings, the Maximized efficiency Optimized Reheat cycle Innovative Gas Turbine Combined cycle (MORITC) Power Generation System with the most effective combination of advanced technologies and the new devices have been proposed. In case of the proposed reheat cycle gas turbine with pressure ratio being 55, the high pressure turbine inlet temperature being 1700C, the low pressure turbine inlet temperature being 800C, combined with the ultra super critical pressure, double reheat type heat recovery Rankine cycle, the thermal efficiency of combined cycle are expected approximately 66.7% (LHV, generator end).

Disappearing Thermo-Economic Sanity in Gas Turbine Combined Cycle Ratings: A Critique

2019 ◽  
Author(s):  
S. Can Gülen
Keyword(s):  
Gas Turbine ◽  
Thermal Efficiency ◽  
Film Cooling ◽  
Pressure Ratio ◽  
Open Loop ◽  
Product Line ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Turbine Inlet ◽  
Steam Turbine Condenser

Abstract There is very little doubt that there has been a noticeable advance in heavy-duty industrial gas turbine technology for utility scale electric power generation in the last decade. In keeping with the first six decades of the technology (roughly 1950 through 2010), the main drivers in increasing thermal efficiency and megawatt ratings have been increasing turbine inlet temperature and airflow. In accordance with the basic thermodynamic principles governing the underlying Brayton cycle, compressor pressure ratio kept pace with them. It is hard to quibble about the 40+ percent in rated thermal efficiency in simple cycle. If projected turbine inlet temperatures and cycle pressure ratios can be sustained in the field, current state-of-the-art in turbine hot gas path metallurgy, coatings and advanced film cooling techniques indeed support published ratings. Unfortunately, published combined cycle ratings are an altogether different matter. It is one thing to set the product line rating performance at an aggressive level with well-understood albeit optimistic assumptions such as very low water-cooled steam turbine condenser pressure with open-loop cooling. It is yet another thing to blatantly disregard fundamental laws of thermodynamics with outlandish performance ratings, which are unlikely to materialize even in the next decade or two cost-effectively (unless an unforeseen transformative step-change in technology materializes). In this paper, using fundamental thermodynamic arguments and detailed heat and mass balance simulations, it will be shown that some, if not all, OEM ratings are losing touch with reality.

scholarly journals Optimum Power Boosting of Gas Turbine Cycles With Refrigerated Inlet Air and Compressor Intercooling

1996 ◽  
Author(s):  
Mohand A. Ait-Ali
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Inlet Temperature ◽  
Turbine Blade Cooling ◽  
High Pressure Ratio ◽  
Blade Cooling ◽  
Air Inlet ◽  
Turbine Inlet ◽  
Compressor Work

With or without turbine blade cooling, gas turbine cycles have consistently higher turbine inlet temperatures than steam turbine cycles. But this advantage is more than offset by the excessive compressor work induced by warm inlet temperatures, particularly during operation on hot summer days. Instead of seeking still higher turbine inlet temperatures by means of sophisticated blade cooling technology and high temperature-resistant blade materials, it is proposed to greatly increase the cycle net work and also improve thermal efficiency by decreasing the compressor work. This is obtained by using refrigerated inlet air and compressor intercooling to an extent which optimizes the refrigerated air inlet temperature and consequently the gas turbine compression ratio with respect to maximum specific net power. The cost effectiveness of this conceptual cycle, which also includes regeneration, has not been examined in this paper as it requires unusually high pressure ratio gas turbines and compressors, as well as high volumetric air flow rate and low temperature refrigeration equipment for which reliable cost data is not easily available.

Genetic Optimization of Steam Injected Gas Turbine Power Plants

2002 ◽  
Author(s):  
Ibrahim Sinan Akmandor ◽  
O¨zhan O¨ksu¨z ◽  
Sec¸kin Go¨kaltun ◽  
Melih Han Bilgin
Keyword(s):  
Gas Turbine ◽  
Power Output ◽  
Thermal Efficiency ◽  
Gas Turbines ◽  
Power Plants ◽  
Pressure Ratio ◽  
Steam Injection ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Compressor Pressure Ratio

A new methodology is developed to find the optimal steam injection levels in simple and combined cycle gas turbine power plants. When steam injection process is being applied to simple cycle gas turbines, it is shown to offer many benefits, including increased power output and efficiency as well as reduced exhaust emissions. For combined cycle power plants, steam injection in the gas turbine, significantly decreases the amount of flow and energy through the steam turbine and the overall power output of the combined cycle is decreased. This study focuses on finding the maximum power output and efficiency of steam injected simple and combined cycle gas turbines. For that purpose, the thermodynamic cycle analysis and a genetic algorithm are linked within an automated design loop. The multi-parameter objective function is either based on the power output or on the overall thermal efficiency. NOx levels have also been taken into account in a third objective function denoted as steam injection effectiveness. The calculations are done for a wide range of parameters such as compressor pressure ratio, turbine inlet temperature, air and steam mass flow rates. Firstly, 6 widely used simple and combined cycle power plants performance are used as test cases for thermodynamic cycle validation. Secondly, gas turbine main parameters are modified to yield the maximum generator power and thermal efficiency. Finally, the effects of uniform crossover, creep mutation, different random number seeds, population size and the number of children per pair of parents on the performance of the genetic algorithm are studied. Parametric analyses show that application of high turbine inlet temperature, high air mass flow rate and no steam injection lead to high power and high combined cycle thermal efficiency. On the contrary, when NOx reduction is desired, steam injection is necessary. For simple cycle, almost full amount of steam injection is required to increase power and efficiency as well as to reduce NOx. Moreover, it is found that the compressor pressure ratio for high power output is significantly lower than the compressor pressure ratio that drives the high thermal efficiency.

Optimization of Organic Rankine Cycles for Off-Shore Applications

2013 ◽  
Author(s):  
Leonardo Pierobon ◽  
Ulrik Larsen ◽  
Tuong Van Nguyen ◽  
Fredrik Haglind
Keyword(s):  
Gas Turbine ◽  
Thermal Efficiency ◽  
Gas Turbines ◽  
Optimization Procedure ◽  
Working Fluid ◽  
Maximum Pressure ◽  
Inlet Temperature ◽  
Outlet Temperature ◽  
Turbine Inlet ◽  
Organic Rankine Cycles

In off-shore oil and gas platform efficiency, the reliability and fuel flexibility are the major concerns when selecting the gas turbine to support the electrical and mechanical demand on the platform. In order to fulfill these requirements, turbine inlet temperature and pressure ratio are not increased up to the optimal values and one or more redundant gas turbines may be employed. With increasing incentives for reducing the CO2 emissions off-shore, improving the thermal efficiency has become a focus area. Due to the peculiar low turbine outlet temperature and due to space and weight constraints, a steam bottoming cycle is not a convenient solution. On the contrary, organic Rankine cycles (ORCs) present the benefits of high simplicity and compactness. Furthermore, the working fluid can be selected considering the temperature profile at which the heat is supplied; hence the heat transfer process and the thermal efficiency of the cycle can be maximized. This paper is aimed at finding the most optimal ORC tailored for off-shore applications using an optimization procedure based on the genetic algorithm. Numerous working fluids are screened through, considering mainly thermal efficiency, but also other characteristics of the fluids, e.g. stability, environmental and human health impacts, and safety issues. Both supercritical and subcritical ORCs are included in the analysis. The optimization procedure is first applied to a conservative ORC where the maximum pressure is limited to 20 bar. Subsequently the optimal working fluid is identified by removing the restriction on the maximum pressure. Different limits on hazards and global warming potential (GWP) are also set. The study is focused on the SGT-500 gas turbine installed on the Draugen platform in the Norwegian Sea. The simulations suggest that, when a high hazard is accepted, cyclohexane is the best solution. With a turbine inlet pressure limit of 20 bar, the combined gas turbine-ORC system presents an efficiency of 43.7%, corresponding to an improvement of 11.9%-points with respect to the gas turbine efficiency. With no upper pressure boundary, cyclohexane at 55.5 bar is the preferable working fluid with a combined thermal efficiency of 44.3%. The supercritical CO2 cycle with a maximum pressure of 192.9 bar is found to be the best alternative if an extremely low hazard is required.

Rolls Royce/Allison 501-K Gas Turbine Anti-Fouling Compressor Coatings Evaluation

2002 ◽  
Author(s):  
Daniel E. Caguiat
Keyword(s):  
Gas Turbine ◽  
Fuel Consumption ◽  
Gas Turbines ◽  
Performance Degradation ◽  
Specific Fuel Consumption ◽  
Inlet Temperature ◽  
Test Results ◽  
Turbine Inlet ◽  
Compressor Performance ◽  
Compressor Efficiency

The Naval Surface Warfare Center, Carderock Division (NSWCCD) Gas Turbine Emerging Technologies Code 9334 was tasked by NSWCCD Shipboard Energy Office Code 859 to research and evaluate fouling resistant compressor coatings for Rolls Royce Allison 501-K Series gas turbines. The objective of these tests was to investigate the feasibility of reducing the rate of compressor fouling degradation and associated rate of specific fuel consumption (SFC) increase through the application of anti-fouling coatings. Code 9334 conducted a market investigation and selected coatings that best fit the test objective. The coatings selected were Sermalon for compressor stages 1 and 2 and Sermaflow S4000 for the remaining 12 compressor stages. Both coatings are manufactured by Sermatech International, are intended to substantially decrease blade surface roughness, have inert top layers, and contain an anti-corrosive aluminum-ceramic base coat. Sermalon contains a Polytetrafluoroethylene (PTFE) topcoat, a substance similar to Teflon, for added fouling resistance. Tests were conducted at the Philadelphia Land Based Engineering Site (LBES). Testing was first performed on the existing LBES 501-K17 gas turbine, which had a non-coated compressor. The compressor was then replaced by a coated compressor and the test was repeated. The test plan consisted of injecting a known amount of salt solution into the gas turbine inlet while gathering compressor performance degradation and fuel economy data for 0, 500, 1000, and 1250 KW generator load levels. This method facilitated a direct comparison of compressor degradation trends for the coated and non-coated compressors operating with the same turbine section, thereby reducing the number of variables involved. The collected data for turbine inlet, temperature, compressor efficiency, and fuel consumption were plotted as a percentage of the baseline conditions for each compressor. The results of each plot show a decrease in the rates of compressor degradation and SFC increase for the coated compressor compared to the non-coated compressor. Overall test results show that it is feasible to utilize anti-fouling compressor coatings to reduce the rate of specific fuel consumption increase associated with compressor performance degradation.

scholarly journals Cooling and Sealing Air System in Industrial Gas Turbine Engines

1996 ◽  
Author(s):  
A. W. Reichert ◽  
M. Janssen
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Gas Turbines ◽  
State Of The Art ◽  
Cooling System ◽  
Inlet Temperature ◽  
Turbine Inlet ◽  
Air System ◽  
Calculation System ◽  
Cooling Air

Siemens heavy duty Gas Turbines have been well known for their high power output combined with high efficiency and reliability for more than 3 decades. Offering state of the art technology at all times, the requirements concerning the cooling and sealing air system have increased with technological development over the years. In particular the increase of the turbine inlet temperature and reduced NOx requirements demand a highly efficient cooling and sealing air system. The new Vx4.3A family of Siemens gas turbines with ISO turbine inlet temperatures of 1190°C in the power range of 70 to 240 MW uses an effective film cooling technique for the turbine stages 1 and 2 to ensure the minimum cooling air requirement possible. In addition, the application of film cooling enables the cooling system to be simplified. For example, in the new gas turbine family no intercooler and no cooling air booster for the first turbine vane are needed. This paper deals with the internal air system of Siemens gas turbines which supplies cooling and sealing air. A general overview is given and some problems and their technical solutions are discussed. Furthermore a state of the art calculation system for the prediction of the thermodynamic states of the cooling and sealing air is introduced. The calculation system is based on the flow calculation package Flowmaster (Flowmaster International Ltd.), which has been modified for the requirements of the internal air system. The comparison of computational results with measurements give a good impression of the high accuracy of the calculation method used.

Expanding Fuel Flexibility in MHPS’ Dry Low NOx Combustor

2018 ◽  
Author(s):  
Katsuyoshi Tada ◽  
Kei Inoue ◽  
Tomo Kawakami ◽  
Keijiro Saitoh ◽  
Satoshi Tanimura
Keyword(s):  
Power Systems ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Environmental Conservation ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Social Perspectives ◽  
Turbine Inlet ◽  
Fuel Flexibility

Gas-turbine combined-cycle (GTCC) power generation is clean and efficient, and its demand will increase in the future from economic and social perspectives. Raising turbine inlet temperature is an effective way to increase combined cycle efficiency and contributes to global environmental conservation by reducing CO2 emissions and preventing global warming. However, increasing turbine inlet temperature can lead to the increase of NOx emissions, depletion of the ozone layer and generation of photochemical smog. To deal with this issue, MHPS (MITSUBISHI HITACHI POWER SYSTEMS) and MHI (MITSUBISHI HEAVY INDUSTRIES) have developed Dry Low NOx (DLN) combustion techniques for high temperature gas turbines. In addition, fuel flexibility is one of the most important features for DLN combustors to meet the requirement of the gas turbine market. MHPS and MHI have demonstrated DLN combustor fuel flexibility with natural gas (NG) fuels that have a large Wobbe Index variation, a Hydrogen-NG mixture, and crude oils.

Off-design performance improvement of twin-shaft gas turbine by variable geometry turbine and compressor besides fuel control

2019 ◽  
Vol 234 (7) ◽  
pp. 957-980
Author(s):  
Sepehr Sanaye ◽  
Salahadin Hosseini
Keyword(s):  
Life Cycle ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Guide Vane ◽  
Design Parameters ◽  
Inlet Guide Vane ◽  
Inlet Temperature ◽  
Gas Generator ◽  
Turbine Inlet ◽  
Exit Temperature

A novel procedure for finding the optimum values of design parameters of industrial twin-shaft gas turbines at various ambient temperatures is presented here. This paper focuses on being off design due to various ambient temperatures. The gas turbine modeling is performed by applying compressor and turbine characteristic maps and using thermodynamic matching method. The gas turbine power output is selected as an objective function in optimization procedure with genetic algorithm. Design parameters are compressor inlet guide vane angle, turbine exit temperature, and power turbine inlet nozzle guide vane angle. The novel constrains in optimization are compressor surge margin and turbine blade life cycle. A trained neural network is used for life cycle estimation of high pressure (gas generator) turbine blades. Results for optimum values for nozzle guide vane/inlet guide vane (23°/27°–27°/6°) in ambient temperature range of 25–45 ℃ provided higher net power output (3–4.3%) and more secured compressor surge margin in comparison with that for gas turbines control by turbine exit temperature. Gas turbines thermal efficiency also increased from 0.09 to 0.34% (while the gas generator turbine first rotor blade creep life cycle was kept almost constant about 40,000 h). Meanwhile, the averaged values for turbine exit temperature/turbine inlet temperature changed from 831.2/1475 to 823/1471°K, respectively, which shows about 1% decrease in turbine exit temperature and 0.3% decrease in turbine inlet temperature.

Off-Design Performance Investigation of a Low Calorific Value Gas Fired Generic-Type Single-Shaft Gas Turbine

2008 ◽  
Vol 130 (3) ◽  
Author(s):  
Raik C. Orbay ◽  
Magnus Genrup ◽  
Pontus Eriksson ◽  
Jens Klingmann
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Calorific Value ◽  
Working Fluid ◽  
Inlet Temperature ◽  
Flammability Limits ◽  
Generic Type ◽  
Wobbe Index ◽  
The Impact

When low calorific value gases are fired, the performance and stability of gas turbines may deteriorate due to a large amount of inertballast and changes in working fluid properties. Since it is rather rare to have custom-built gas turbines for low lower heating value (LHV) operation, the engine will be forced to operate outside its design envelope. This, in turn, poses limitations to usable fuel choices. Typical restraints are decrease in Wobbe index and surge and flutter margins for turbomachinery. In this study, an advanced performance deck has been used to quantify the impact of firing low-LHV gases in a generic-type recuperated as well as unrecuperated gas turbine. A single-shaft gas turbine characterized by a compressor and an expander map is considered. Emphasis has been put on predicting the off-design behavior. The combustor is discussed and related to previous experiments that include investigation of flammability limits, Wobbe index, flame position, etc. The computations show that at constant turbine inlet temperature, the shaft power and the pressure ratio will increase; however, the surge margin will decrease. Possible design changes in the component level are also discussed. Aerodynamic issues (and necessary modifications) that can pose severe limitations on the gas turbine compressor and turbine sections are discussed. Typical methods for axial turbine capacity adjustment are presented and discussed.

Sign in / Sign up

Export Citation Format

Share Document