Measurements of Radial Vortices, Spill Forward and Vortex Breakdown in a Transonic Compressor

2017 ◽  
Author(s):  
Christoph Brandstetter ◽  
Maximilian Jüngst ◽  
Heinz-Peter Schiffer
Keyword(s):  
High Speed ◽  
Large Scale ◽  
Vortex Breakdown ◽  
Measurement Techniques ◽  
Leading Edge ◽  
Rotating Stall ◽  
Clear Correlation ◽  
Blade Vibration ◽  
Transonic Compressor ◽  
Blade Vibrations

The phenomena prior to rotating stall were investigated in a high-speed compressor test rig using optical and pneumatic measurement techniques. A number of throttling procedures was performed at transonic and subsonic speedlines with the aim to detect the unsteady effects initiating rotating stall or large amplitude blade vibrations. At transonic speed radial vortices traveling around the circumference were detected in the upstream part of the rotor using phase-locked PIV measurements above 92% span and unsteady wall pressure measurements. When these radial vortices impinge on a blade leading edge, they cause a forward spill of fluid around the leading edge. The effects are accompanied by a large-scale vortex breakdown in the blade passage leading to immense blockage in the endwall region. At subsonic speeds, the observed flow phenomena are similar but differ in intensity and structure. During the throttling procedure, blade vibration amplitudes were monitored using strain gauges and blade tip timing instrumentation. Non-synchronous blade vibrations in the first torsional eigenmode were measured as the rotor approached stall. Using the different types of instrumentation, it was possible to align the aerodynamic flow features with blade vibration levels. The results show a clear correlation between the occurrence of radial vortices and blade vibrations.

Measurements of Radial Vortices, Spill Forward, and Vortex Breakdown in a Transonic Compressor

2018 ◽  
Vol 140 (6) ◽  
Author(s):  
Christoph Brandstetter ◽  
Maximilian Jüngst ◽  
Heinz-Peter Schiffer
Keyword(s):  
High Speed ◽  
Large Scale ◽  
Vortex Breakdown ◽  
Measurement Techniques ◽  
Leading Edge ◽  
Rotating Stall ◽  
Clear Correlation ◽  
Blade Vibration ◽  
Transonic Compressor ◽  
Blade Vibrations

The phenomena prior to rotating stall were investigated in a high-speed compressor test rig using optical and pneumatic measurement techniques. A number of throttling procedures were performed at transonic and subsonic speedlines with the aim to detect the unsteady effects initiating rotating stall or large amplitude blade vibrations. At transonic speed, radial vortices traveling around the circumference were detected in the upstream part of the rotor using phase-locked particle-image-velocimetry (PIV) measurements above 92% span and unsteady wall pressure measurements. When these radial vortices impinge on a blade leading edge (LE), they cause a forward spill of fluid around the LE. The effects are accompanied by a large-scale vortex breakdown in the blade passage leading to immense blockage in the endwall region. At subsonic speeds, the observed flow phenomena are similar but differ in intensity and structure. During the throttling procedure, blade vibration amplitudes were monitored using strain gauges (SG) and blade tip timing instrumentation. Nonsynchronous blade vibrations in the first torsional eigenmode were measured as the rotor approached stall. Using the different types of instrumentation, it was possible to align the aerodynamic flow features with blade vibration levels. The results show a clear correlation between the occurrence of radial vortices and blade vibrations.

scholarly journals Blade Vibrations of a High Speed Compressor Blisk-Rotor: Numerical Resonance Tuning and Optical Measurements

1996 ◽  
Author(s):  
J. Frischbier ◽  
G. Schulze ◽  
M. Zielinski ◽  
G. Ziller ◽  
C. Blaha ◽  
...  
Keyword(s):  
Rotor Blade ◽  
High Speed ◽  
Mechanical Design ◽  
Optimization Technique ◽  
Optical Measurements ◽  
Vibration Measurement ◽  
Blade Vibration ◽  
Transonic Compressor ◽  
Resonance Tuning ◽  
Blade Vibrations

A major challenge during the design process of a modern low aspect ratio high speed axial compressor is to find rotor blade geometries that meet both, aerodynamic and mechanical requirements. This paper deals with the mechanical design of a transonic compressor blade. In order to meet the mechanical requirements in a short development time, new methods were used: A numerical optimization tool and an optical blade vibration measurement method: The numerical resonance tuning took advantage of a semi-automatic optimization technique, based on a Finite Element vibration anlysis tool. The intention was to find a geometry which has no critical resonances (with fundamental engine orders) within the operation range. To verify the calculated blade natural frequencies and eigen-values standard shaker tests using a laser holography system were carried out. Blades under g-load in the running compressor were investigated with an in-house developed vibration measurement system. This system is able to measure frequencies and amplitudes of the rotor blade vibrations without blade instrumentation but small optical probes, mounted in the compressor casing. The measured resonance points are in good agreement with the predictions. All amplitudes are far below the blade fatigue limits.

scholarly journals Effects of Tip Leakage Flow on the Aerodynamic Performance and Stability of an Axial-Flow Transonic Compressor Stage

Energies ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4168
Author(s):  
Botao Zhang ◽  
Xiaochen Mao ◽  
Xiaoxiong Wu ◽  
Bo Liu
Keyword(s):  
Boundary Layer ◽  
Shock Wave ◽  
Axial Flow ◽  
Leading Edge ◽  
Rotating Stall ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Transonic Compressor

To explain the effect of tip leakage flow on the performance of an axial-flow transonic compressor, the compressors with different rotor tip clearances were studied numerically. The results show that as the rotor tip clearance increases, the leakage flow intensity is increased, the shock wave position is moved backward, and the interaction between the tip leakage vortex and shock wave is intensified, while that between the boundary layer and shock wave is weakened. Most of all, the stall mechanisms of the compressors with varying rotor tip clearances are different. The clearance leakage flow is the main cause of the rotating stall under large rotor tip clearance. However, the stall form for the compressor with half of the designed tip clearance is caused by the joint action of the rotor tip stall caused by the leakage flow spillage at the blade leading edge and the whole blade span stall caused by the separation of the boundary layer of the rotor and the stator passage. Within the investigated varied range, when the rotor tip clearance size is half of the design, the compressor performance is improved best, and the peak efficiency and stall margin are increased by 0.2% and 3.5%, respectively.

Steady longitudinal vortices in supersonic turbulent separated flows

2011 ◽  
Vol 672 ◽  
pp. 451-476 ◽  
Author(s):  
ERICH SCHÜLEIN ◽  
VICTOR M. TROFIMOV
Keyword(s):  
High Speed ◽  
Large Scale ◽  
Roughness Element ◽  
Vortex Generator ◽  
Vortex Pair ◽  
Leading Edge ◽  
Separated Flows ◽  
Vortex Generators ◽  
Longitudinal Vortices ◽  
Oil Flow

Large-scale longitudinal vortices in high-speed turbulent separated flows caused by relatively small irregularities at the model leading edges or at the model surfaces are investigated in this paper. Oil-flow visualization and infrared thermography techniques were applied in the wind tunnel tests at Mach numbers 3 and 5 to investigate the nominally 2-D ramp flow at deflection angles of 20°, 25° and 30°. The surface contour anomalies have been artificially simulated by very thin strips (vortex generators) of different shapes and thicknesses attached to the model surface. It is shown that the introduced streamwise vortical disturbances survive over very large downstream distances of the order of 104 vortex-generator heights in turbulent supersonic flows without pressure gradients. It is demonstrated that each vortex pair induced in the reattachment region of the ramp is definitely a child of a vortex pair, which was generated originally, for instance, by the small roughness element near the leading edge. The dependence of the spacing and intensity of the observed longitudinal vortices on the introduced disturbances (thickness and spanwise size of vortex generators) and on the flow parameters (Reynolds numbers, boundary-layer thickness, compression corner angles, etc.) has been shown experimentally.

Stall Inception in a High Speed Centrifugal Compressor During Speed Transients

2017 ◽  
Author(s):  
Fangyuan Lou ◽  
John C. Fabian ◽  
Nicole L. Key
Keyword(s):  
Heat Transfer ◽  
Centrifugal Compressor ◽  
High Speed ◽  
Flow Instability ◽  
Leading Edge ◽  
Fast Response ◽  
Rotating Stall ◽  
Transient Performance ◽  
Stall Inception ◽  
Pressure Transducers

The inception and evolution of rotating stall in a high-speed centrifugal compressor are characterized during speed transients. Experiments were performed in the Single Stage Centrifugal Compressor (SSCC) facility at Purdue University and include speed transients from sub-idle to full speed at different throttle settings while collecting transient performance data. Results show a substantial difference in the compressor transient performance for accelerations versus decelerations. This difference is associated with the heat transfer between the flow and the hardware. The heat transfer from the hardware to the flow during the decelerations locates the compressor operating condition closer to the surge line and results in a significant reduction in surge margin during decelerations. Additionally, data were acquired from fast-response pressure transducers along the impeller shroud, in the vaneless space, and along the diffuser passages. Two different patterns of flow instabilities, including mild surge and short-length-scale rotating stall, are observed during the decelerations. The instability starts with a small pressure perturbation at the impeller leading edge and quickly develops into a single-lobe rotating stall burst. The stall cell propagates in the direction opposite of impeller rotation at approximately one third of the rotor speed. The rotating stall bursts are observed in both the impeller and diffuser, with the largest magnitudes near the diffuser throat. Furthermore, the flow instability develops into a continuous high frequency stall and remains in the fully developed stall condition.

On the Breakdown at High Incidences of the Leading Edge Vortices on Delta Wings

1960 ◽  
Vol 64 (596) ◽  
pp. 491-493 ◽  
Author(s):  
B. J. Elle
Keyword(s):  
High Speed ◽  
Recent Article ◽  
Vortex Breakdown ◽  
Leading Edge ◽  
Critical Value ◽  
Delta Wings ◽  
Edge Separation ◽  
Leading Edge Vortices

In a recent article, H. Werlé, has described how the free spiral vortices on delta wings with leading edge separation suddenly expand if the incidence is increased beyond a critical value. His description conforms to a great extent with the results, arrived at during an English investigation of the same phenomenon (called the vortex breakdown), but the interpretations of the observations, suggested by the two sources, are different. Against this background it is felt that some further comments and some pertinent high speed observations, may be of interest.

Fan Stability With Leading Edge Damage: Blind Prediction and Validation

2021 ◽  
Author(s):  
E. J. Gunn ◽  
T. Brandvik ◽  
M. J. Wilson ◽  
R. Maxwell
Keyword(s):  
Supersonic Flow ◽  
High Speed ◽  
Leading Edge ◽  
Rotating Stall ◽  
Stall Inception ◽  
Blind Prediction ◽  
Edge Damage ◽  
The Impact ◽  
Operating Points ◽  
Relative Flow

Abstract This paper considers the impact of a damaged leading edge on the stall margin and stall inception mechanisms of a transonic, low pressure ratio fan. The damage takes the form of a squared-off leading edge over the upper half of the blade. Full-annulus, unsteady CFD simulations are used to explain the stall inception mechanisms for the fan at low- and high-speed operating points. A combination of steady and unsteady simulations show that the fan is predicted to be sensitive to leading edge damage at low speed, but insensitive at high speed. This blind prediction aligns well with rig test data. The difference in response is shown to be caused by the change between subsonic and supersonic flow regimes at the leading edge. Where the inlet relative flow is subsonic, rotating stall is initiated by growth and propagation of a subsonic leading edge flow separation. This separation is shown to be triggered at higher mass flow rates when the leading edge is damaged, reducing the stable flow range. Where the inlet relative flow is supersonic, the flow undergoes a supersonic expansion around the leading edge, creating a supersonic flow patch terminated by a shock on the suction surface. Rotating stall is triggered by growth of this separation, which is insensitive to leading edge shape. This creates a marked difference in sensitivity to damage at low- and high-speed operating points.

Acoustic Resonance in an Axial Multistage Compressor Leading to Non-Synchronous Blade Vibration

2020 ◽  
Author(s):  
Anne-Lise Fiquet ◽  
Agathe Vercoutter ◽  
Nicolas Buffaz ◽  
Stéphane Aubert ◽  
Christoph Brandstetter
Keyword(s):  
Acoustic Waves ◽  
High Speed ◽  
Numerical Study ◽  
Acoustic Resonance ◽  
Structural Vibration ◽  
Wave Number ◽  
Blade Vibration ◽  
Acoustic Modes ◽  
Blade Vibrations ◽  
Circumferential Wave

Abstract Significant non-synchronous blade vibrations (NSV) have been observed in an experimental three-stage high-speed compressor at part-speed conditions. High amplitude acoustic modes, propagating around the circumference and originating in the highly loaded Stage-3 have been observed in coherence with the structural vibration mode. In order to understand the occurring phenomena, a detailed numerical study has been carried out to reproduce the mechanism. Unsteady full annulus RANS simulations of the whole setup have been performed using the solver elsA. The results revealed the development of propagating acoustic modes which are partially trapped in the annulus and are in resonance with an aerodynamic disturbance in Rotor-3. The aerodynamic disturbance is identified as an unsteady separation of the blade boundary layer in Rotor-3. The results indicate that the frequency and phase of the separation adapt to match those of the acoustic wave, and are therefore governed by acoustic propagation conditions. Furthermore, the simulations clearly show the modulation of the propagating wave with the rotor blades, leading to a change of circumferential wave numbers while passing the blade row. To analyze if the effect is self-induced by the blade vibration, a noncoherent structural mode has been imposed in the simulations. Even at high vibration amplitude the formerly observed acoustic mode did not change its circumferential wave number. This phenomenon is highly relevant to modern compressor designs, since the appearance of the axially propagating acoustic waves can excite blade vibrations if they coincide with a structural eigenmode, as observed in the presented experiments.

scholarly journals Investigation on the Flow Field Entropy Structure of Non-Synchronous Blade Vibration in an Axial Turbocompressor

Entropy ◽  
2020 ◽  
Vol 22 (12) ◽  
pp. 1372
Author(s):  
Mingming Zhang ◽  
Anping Hou
Keyword(s):  
Flow Field ◽  
High Speed ◽  
Guide Vane ◽  
Leading Edge ◽  
Inlet Guide Vane ◽  
Tip Leakage Flow ◽  
Good Correspondence ◽  
Blade Vibration ◽  
Tip Leakage ◽  
Spiral Vortex

In order to explore the inducing factors and mechanism of the non-synchronous vibration, the flow field structure and its formation mechanism in the non-synchronous vibration state of a high speed turbocompressor are discussed in this paper, based on the fluid–structure interaction method. The predicted frequencies fBV (4.4EO), fAR (9.6EO) in the field have a good correspondence with the experimental data, which verify the reliability and accuracy of the numerical method. The results indicate that, under a deviation in the adjustment of inlet guide vane (IGV), the disturbances of pressure in the tip diffuse upstream and downstream, and maintain the corresponding relationship with the non-synchronous vibration frequency of the blade. An instability flow that developed at the tip region of 90% span emerged due to interactions among the incoming main flow, the axial separation backflow, and the tip leakage vortices. The separation vortices in the blade passage mixed up with the tip leakage flow reverse at the trailing edge of blade tip, presenting a spiral vortex structure which flows upstream to the leading edge of the adjacent blade. The disturbances of the spiral vortexes emerge to rotate at 54.5% of the rotor speed in the same rotating direction as a modal oscillation. The blade vibration in the turbocompressor is found to be related to the unsteadiness of the tip flow. The large pressure oscillation caused by the movement of the spiral vortex is regarded as the one of the main drivers for the non-synchronous vibration for the present turbocompressor, besides the deviation in the adjustment of IGV.

Visualizations of Flow Structures in the Rotor Passage of an Axial Compressor at the Onset of Stall

2017 ◽  
Vol 139 (4) ◽  
Author(s):  
Huang Chen ◽  
Yuanchao Li ◽  
David Tan ◽  
Joseph Katz
Keyword(s):  
High Speed ◽  
Large Scale ◽  
Incidence Angle ◽  
Axial Compressor ◽  
Leading Edge ◽  
Suction Side ◽  
Stereoscopic Particle Image Velocimetry ◽  
High Speed Imaging ◽  
Vortical Structures ◽  
Flow Phenomena

Experiments preformed in the JHU refractive index matched facility examine flow phenomena developing in the rotor passage of an axial compressor at the onset of stall. High-speed imaging of cavitation performed at low pressures qualitatively visualizes vortical structures. Stereoscopic particle image velocimetry (SPIV) measurements provide detailed snapshots and ensemble statistics of the flow in a series of meridional planes. At prestall condition, the tip leakage vortex (TLV) breaks up into widely distributed intermittent vortical structures shortly after rollup. The most prominent instability involves periodic formation of large-scale backflow vortices (BFVs) that extend diagonally upstream, from the suction side (SS) of one blade at midchord to the pressure side (PS) near the leading edge of the next blade. The 3D vorticity distributions obtained from data recorded in closely spaced planes show that the BFVs originate form at the transition between the high circumferential velocity region below the TLV center and the main passage flow radially inward from it. When the BFVs penetrate to the next passage across the tip gap or by circumventing the leading edge, they trigger a similar phenomenon there, sustaining the process. Further reduction in flow rate into the stall range increases the number and size of the backflow vortices, and they regularly propagate upstream of the leading edge of the next blade, where they increase the incidence angle in the tip corner. As this process proliferates circumferentially, the BFVs rotate with the blades, indicating that there is very little through flow across the tip region.

Sign in / Sign up

Export Citation Format

Share Document