Heat Transfer Augmentation and Flow Visualization With Delta Winglets in a Tube: A Numerical Approach

2020 ◽  
Author(s):  
Md. Islam ◽  
Liang Guangda ◽  
Md. Mahbub Alam
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Thermal Performance ◽  
Performance Enhancement ◽  
Swirling Flow ◽  
Circular Tube ◽  
Vortex Generator ◽  
Attack Angle ◽  
Maximum Enhancement ◽  
Longitudinal Vortices

Abstract In this research, heat transfer and pressure penalty from a circular tube with delta winglets insert are numerically investigated through Computational Fluid Dynamics (CFD) methodology. Numerical analysis with and without vortex generators (VGs) insert in a tube are done for a turbulent air flow, Reynolds number ranging from 6000 to 33000, under constant heat flux condition on the circular tube model surface. In our current research, we employed the shear stress transport (SST) k-omega model. The Nusselt number and friction factor results show the influence of the VGs insert on thermal performance. Effects of different winglet attack angles and blockage ratios on thermal performance enhancement were examined. Thermal performance is enhanced 5.1–30.7% using winglets in a tube. It is observed that small blockage ratio, B = 0.1 performed better than its counterpart of 0.2 and 0.3 for all the Reynolds number and for the same attack angle. The attack angle β = 15° and 30° showed better thermal performance enhancement at lower Re while at higher Re, β = 15° showed better performance. The maximum enhancement obtained for β = 30° and B = 0.1. Winglet vortex generator could create swirling flow when attack angle is 0 or 15°. When attack angle is increased, both swirling flow and longitudinal vortices appeared. At attack angle of 45°, large longitudinal vortices was found.

Heat Transfer Enhancement With Delta Winglets Vortex Generator for Different Arrangement in a Circular Tube

2018 ◽  
Author(s):  
Md. Islam ◽  
A. Nurizki ◽  
A. Kareem ◽  
A. Baba
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Thermal Performance ◽  
Heat Transfer Performance ◽  
Circular Tube ◽  
Flow Behavior ◽  
Vortex Generator ◽  
Attack Angle ◽  
Transfer Performance ◽  
Pitch Ratio

Various technologies have been developed to enhance the heat transfer. Vortex generator (VG) is one of the passive techniques which can change the flow behavior and ultimately enhances the heat transfer performance. Delta winglet (DW) vortex generator can create longitudinal and horseshoe vortices which do not decay until further downstream and consequently increase heat transfer coefficient with comparatively lower pressure drop. With this vortex generator, it is expected to have higher Nusselt number with some increase of friction factor. Therefore, this study is to study the effect of pitch ratio (PR) and attack angle (B) of DW vortex generator to increase the thermal performance of heat exchanger. Four delta winglets are attached into a ring. Those rings attached with VGs will be used to investigate the influence of different parameters to heat transfer performance. In this study VGs were placed inside a circular copper tube and the heating coil was wrapped up around the outer surface of the copper tube to generate a constant heat flux condition. The experimental setup consists of a blower, orifice meter, flow straightener, calm/flow developing section and test section. The results show the friction factor, Nusselt number, and Thermal Performance Enhancement. It increases the thermal performance due to the formation of longitudinal vortex inside the circular tube. Pitch ratio and attack angle seem to have significant impact on the flow and heat transfer. The Pitch ratio of 1.6 have the highest impact on both (f/f0) and (Nu/Nuo) followed by attack angle. Smoke flow visualization technique was used to study flow behavior and flow structures.

Impact of Delta-Winglet Pair of Vortex Generators on the Thermal and Hydraulic Performance of a Triangular Channel Using Al2O3–Water Nanofluid

2013 ◽  
Vol 136 (2) ◽  
Author(s):  
Hamdi E. Ahmed ◽  
M. Z. Yusoff
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Coefficient ◽  
Volume Fraction ◽  
Vortex Generator ◽  
Attack Angle ◽  
Vortex Generators ◽  
Triangular Channel ◽  
Delta Winglet ◽  
The Heat Transfer Coefficient

This paper presents the laminar forced convection of Al2O3–water nanofluid in a triangular channel, subjected to a constant and uniform heat flux at the slant walls, using delta-winglet pair (DWP) of vortex generator which is numerically investigated in three dimensions. The governing equations of mass, momentum, and energy are solved using the finite volume method (FVM). The nanofluid properties are estimated as constant and temperature-dependent properties. The nanoparticle concentrations and diameters are in ranges of 1–4% and 25–85 nm, respectively. Different attack angles of vortex generators are examined which are 7 deg, 15 deg, 30 deg, and 45 deg with range of Reynolds number from 100 to 2000. The results show that the heat transfer coefficient is remarkable dependent on the attack angle of vortex generators and the volume fraction of nanoparticles. The heat transfer coefficient increases as the attack angle increases from 7 deg to 30 deg and then diminishes at 45 deg. The heat transfer rate remarkably depends on the nanoparticle concentration and diameter, attack angle of vortex generator and Reynolds number. An increase in the shear stress is found when attack angle, volume fraction, and Reynolds number increase.

Endwall Heat Transfer Enhancement Around Cylinders With a Wall-Mounted Vortex Generator Pair

2017 ◽  
Author(s):  
Safeer Hussain ◽  
Jian Liu ◽  
Lei Wang ◽  
Bengt Sundén
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Enhancement ◽  
Thermal Performance ◽  
Vortex Generator ◽  
Diameter Ratio ◽  
Upstream Region ◽  
Spanwise Direction ◽  
Transfer Enhancement ◽  
Nusselt Numbers

Measurement of endwall heat transfer around a circular cylinder with a vortex generator pair has been investigated. Steady state liquid crystal thermography is adopted. Cylinders having two different height to diameter ratios have been employed. In one case, the cylinder has one end free in the flow and in the other case it has both ends attached on the walls. Local Nusselt numbers both upstream and downstream of the cylinder with and without the vortex generator pair are calculated. Nusselt numbers in streamwise and spanwise directions for both cases with vortex generator are compared with each other as well as with corresponding base cases. It is found from the experiments that the vortex generator influences the endwall heat transfer significantly downstream of the cylinder but has a small effect in the upstream region. Moreover, for different height to diameter ratio of the cylinder different heat transfer patterns are observed downstream of the cylinder. The vortex generator pair plays its major role on the endwall heat transfer enhancement in the spanwise direction and it expands as one moves from the upstream to downstream direction. To fully understand the advantage of the vortex generator pair, thermal performance is calculated for each case and it was found that in presence of the vortex generator pair, the cylinder with shorter height to diameter ratio shows higher thermal performance. Reynolds number dependence has also been investigated and it was found that the thermal performance decreases with increasing Reynolds number for both cases having a vortex generator pair.

scholarly journals Numerical Study on the Influence of Vortex Generator Arrangement on Heat Transfer Enhancement of Oil-Cooled Motor

Energies ◽  
2021 ◽  
Vol 14 (21) ◽  
pp. 6870
Author(s):  
Junjie Zhao ◽  
Bin Zhang ◽  
Xiaoli Fu ◽  
Shenglin Yan
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Enhancement ◽  
Vortex Generator ◽  
Attack Angle ◽  
Vortex Generators ◽  
Dimensionless Number ◽  
Transfer Enhancement ◽  
Enhanced Heat Transfer ◽  
Longitudinal Distance

At present, vortex generators have been extensively used in radiators to improve the overall heat transfer performance. However, there is no research on the effect of vortex generators on the ends of motor coils. Meanwhile, the current research mainly concentrates on the attack angle, shape and size, and lacks a detailed study on the transverse and longitudinal distance and arrangement of vortex generators. In this paper, the improved dimensionless number is used as the key index to evaluate the overall performance of enhanced heat transfer. Firstly, the influence of the attack angle on heat transfer enhancement is discussed through a single pair of rectangular vortex generators, and the results demonstrate that the vortex generator with a 45° attack angle is superior. On this basis, we compare the effects of different longitudinal distances (2 h, 4 h, and 6 h, h meaning the height of vortex generator) on enhanced heat transfer under four distribution modes: Flow-Up (FU), Flow-Down (FU), Flow-Up-Down (FUD), Flow-Down-UP (FDU). Thereafter, the performances of different transverse distances (0.25 h, 0.5 h, and 0.75 h) of the vortex generators are numerically simulated. When comparing the longitudinal distances, FD with a longitudinal distance of 4 h (FD-4h) performs well when the Reynolds number is less than 4000, and FU with a longitudinal distance of 4 h (FU-4h) performs better when the Reynolds number is greater than 4000. Similarly, in the comparison of transverse distances, FD-4h still performs well when the Reynolds number is less than 4000, and FU with a longitudinal distance of 4 h and transverse distance of 0.5 h (FU-4h − 0.5h) is more prominent when the Reynolds number is greater than 4000.

Air-Side Heat Transfer Enhancement by a Novel Winglet-Type Vortex Generator Array in a Round-Tube Plain-Fin Heat Exchanger

2009 ◽  
Author(s):  
Jing He ◽  
Liping Liu ◽  
Anthony M. Jacobi
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Exchanger ◽  
Heat Transfer Enhancement ◽  
Vortex Generator ◽  
Attack Angle ◽  
Transfer Enhancement ◽  
Number Range ◽  
Reynolds Number Range ◽  
Goodness Factor

The impact of vortex generator (VG) arrays for air-side heat transfer enhancement is experimentally investigated by full-scale wind-tunnel testing of a plain-fin-and-tube heat exchanger. The VG array is deployed in a “V” to try to create a constructive interference between vortices. Each array is composed of two delta-winglet pairs (four VGs), and placed at an attack angle of 10° or 30°. The frontal air velocity considered is between 2.3–5.4 m/s, corresponding to a Reynolds number range based on the hydraulic diameter of 1500–3400. The thermal-hydraulic performance of the heat exchanger with and without VG enhancement is provided under dry-surface conditions. The experimental results indicate little impact at a relatively small attack angle of 10°. While for the 30° array, a 25–55% augmentation in air-side heat transfer coefficient is measured, but with a pressure drop penalty of 100%. Nevertheless, performance evaluation using the area goodness factor and the volume goodness factor both indicate the superiority of the enhanced heat exchanger by the 30° array over the entire Reynolds number range. The proposed array is found more effective at comparatively low Reynolds numbers, representative of many HVAC&R applications and compact heat exchanger designs.

Investigations on Convective Heat Transfer Enhancement in Circular Tube Radiator Using Al2O3 and CuO Nanofluids

2018 ◽  
Vol 10 (5) ◽  
Author(s):  
Sobin Alosious ◽  
S. R. Sarath ◽  
Anjan R. Nair ◽  
K. Krishnakumar
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Reynolds Number ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Volume Concentration ◽  
Circular Tube ◽  
Convective Heat Transfer Coefficient ◽  
Maximum Enhancement ◽  
Study Results

In this study, forced convective heat transfer inside a circular tube automobile radiator is experimentally and numerically investigated. The investigation is carried out using Al2O3 and CuO nanofluids with water as their base fluid. A single radiator circular tube with the same dimensions is numerically modeled. Numerical model is validated using the experimental study results. In the experimental study, Al2O3 and CuO nanofluids of 0.05% volume concentrations (ϕ) were recirculated through the radiator for the Reynolds number (Re) between 260 and 1560. The numerical investigation is conducted for the nanoparticle volume concentration from 0% to 6.0% and 260 < Re < 1560. The investigation shows an enhancement of convective heat transfer coefficient (h) with the increase in nanoparticle volume concentration and with the Reynolds number. A maximum enhancement of 38% and 33% were found for Al2O3 and CuO nanofluids of ϕ = 1% and Re = 1560. For the same cooling load of the radiator, the pumping power can be reduced by 8% and 10%, when Al2O3 and CuO nanofluids (ϕ = 0.8%) were used. Enhancement in convective heat transfer can be utilized to reduce the radiator surface area required. However, the addition of nanofluid results in an enhancement of density (ρ) and viscosity (μ) along with a reduction in specific heat capacity (Cp). Hence, the selection of nanoparticle volume concentration should consider its effect on the thermophysical properties mentioned earlier. It is found that the preferred concentration is between 0.4% and 0.8% for both Al2O3 and CuO nanofluids. In our investigations, it is observed that the convective heat transfer performance of Al2O3 nanofluid is better than the CuO nanofluid.

scholarly journals Simulation approach on turbulent thermal performance factor of Al2O3-Cu/water hybrid nanofluid in circular and non-circular ducts

2021 ◽  
Vol 3 (3) ◽  
Author(s):  
Ing Jiat Kendrick Wong ◽  
Ngieng Tze Angnes Tiong
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Pressure Drop ◽  
Thermal Performance ◽  
Heat Transfer Performance ◽  
Pure Water ◽  
Hybrid Nanofluid ◽  
Performance Factor ◽  
Thermal Performance Factor ◽  
The Heat Transfer Coefficient

AbstractThis paper presents the numerical study of thermal performance factor of Al2O3-Cu/water hybrid nanofluid in circular and non-circular ducts (square and rectangular). Turbulent regime is studied with the Reynolds number ranges from 10000 to 100000. The heat transfer performance and flow behaviour of hybrid nanofluid are investigated, considering the nanofluid volume concentration between 0.1 and 2%. The thermal performance factor of hybrid nanofluid is evaluated in terms of performance evaluation criteria (PEC). This present numerical results are successfully validated with the data from the literature. The results indicate that the heat transfer coefficient and Nusselt number of Al2O3-Cu/water hybrid nanofluid are higher than those of Al2O3/water nanofluid and pure water. However, this heat transfer enhancement is achieved at the expense of an increased pressure drop. The heat transfer coefficient of 2% hybrid nanofluid is approximately 58.6% larger than the value of pure water at the Reynolds number of 10000. For the same concentration and Reynolds number, the pressure drop of hybrid nanofluid is 4.79 times higher than the pressure drop of water. The heat transfer performance is the best in the circular pipe compared to the non-circular ducts, but its pressure drop increment is also the largest. The hybrid nanofluid helps to improve the problem of low heat transfer characteristic in the non-circular ducts. In overall, the hybrid nanofluid flow in circular and non-circular ducts are reported to possess better thermal performance factor than that of water. The maximum attainable PEC is obtained by 2% hybrid nanofluid in the square duct at the Reynolds Number of 60000. This study can help to determine which geometry is efficient for the heat transfer application of hybrid nanofluid.

Heat transfer enhancement using second mode self-oscillating structures

2019 ◽  
Vol 30 (7) ◽  
pp. 3827-3842
Author(s):  
Samer Ali ◽  
Zein Alabidin Shami ◽  
Ali Badran ◽  
Charbel Habchi
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Laminar Flow ◽  
Flow Regime ◽  
Vortex Generator ◽  
Reynolds Numbers ◽  
Content Type ◽  
Laminar Flow Regime ◽  
Second Mode

Purpose In this paper, self-sustained second mode oscillations of flexible vortex generator (FVG) are produced to enhance the heat transfer in two-dimensional laminar flow regime. The purpose of this study is to determine the critical Reynolds number at which FVG becomes more efficient than rigid vortex generators (RVGs). Design/methodology/approach Ten cases were studied with different Reynolds numbers varying from 200 to 2,000. The Nusselt number and friction coefficients of the FVG cases are compared to those of RVG and empty channel at the same Reynolds numbers. Findings For Reynolds numbers higher than 800, the FVG oscillates in the second mode causing a significant increase in the velocity gradients generating unsteady coherent flow structures. The highest performance was obtained at the maximum Reynolds number for which the global Nusselt number is improved by 35.3 and 41.4 per cent with respect to empty channel and rigid configuration, respectively. Moreover, the thermal enhancement factor corresponding to FVG is 72 per cent higher than that of RVG. Practical implications The results obtained here can help in the design of novel multifunctional heat exchangers/reactors by using flexible tabs and inserts instead of rigid ones. Originality/value The originality of this paper is the use of second mode oscillations of FVG to enhance heat transfer in laminar flow regime.

Heat Transfer Enhancement in a Rectangular (AR = 3:1) Channel With V-Shaped Dimples

2012 ◽  
Vol 135 (1) ◽  
Author(s):  
C. Neil Jordan ◽  
Lesley M. Wright
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Liquid Crystal ◽  
Pressure Drop ◽  
Heat Transfer Enhancement ◽  
Thermal Performance ◽  
Secondary Flows ◽  
Transfer Enhancement ◽  
Reduced Pressure

An alternative to ribs for internal heat transfer enhancement of gas turbine airfoils is dimpled depressions. Relative to ribs, dimples incur a reduced pressure drop, which can increase the overall thermal performance of the channel. This experimental investigation measures detailed Nusselt number ratio distributions obtained from an array of V-shaped dimples (δ/D = 0.30). Although the V-shaped dimple array is derived from a traditional hemispherical dimple array, the V-shaped dimples are arranged in an in-line pattern. The resulting spacing of the V-shaped dimples is 3.2D in both the streamwise and spanwise directions. A single wide wall of a rectangular channel (AR = 3:1) is lined with V-shaped dimples. The channel Reynolds number ranges from 10,000–40,000. Detailed Nusselt number ratios are obtained using both a transient liquid crystal technique and a newly developed transient temperature sensitive paint (TSP) technique. Therefore, the TSP technique is not only validated against a baseline geometry (smooth channel), but it is also validated against a more established technique. Measurements indicate that the proposed V-shaped dimple design is a promising alternative to traditional ribs or hemispherical dimples. At lower Reynolds numbers, the V-shaped dimples display heat transfer and friction behavior similar to traditional dimples. However, as the Reynolds number increases to 30,000 and 40,000, secondary flows developed in the V-shaped concavities further enhance the heat transfer from the dimpled surface (similar to angled and V-shaped rib induced secondary flows). This additional enhancement is obtained with only a marginal increase in the pressure drop. Therefore, as the Reynolds number within the channel increases, the thermal performance also increases. While this trend has been confirmed with both the transient TSP and liquid crystal techniques, TSP is shown to have limited capabilities when acquiring highly resolved detailed heat transfer coefficient distributions.

Thermal Performance Assessment of Turbulent Flow Through Dimpled Tubes

2010 ◽  
Author(s):  
Pornchai Nivesrangsan ◽  
Somsak Pethkool ◽  
Kwanchai Nanan ◽  
Monsak Pimsarn ◽  
Smith Eiamsa-ard
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Friction Factor ◽  
Heat Transfer Rate ◽  
Thermal Performance ◽  
Transfer Rate ◽  
Staggered Arrangement ◽  
Plain Tube ◽  
Pitch Ratio ◽  
Surface Patterns

This paper presents the heat transfer augmentation and friction factor characteristics by means of dimpled tubes. The experiments were conducted using the dimpled tubes with two different dimpled-surface patterns including aligned arrangement (A-A) and staggered arrangement (S-A), each with two pitch ratios (PR = p/Di = 0.6 and 1.0), for Reynolds number ranging from 9800 to 67,000. The experimental results achieved from the dimpled tubes are compared with those obtained from the plain tube. Evidently, the dimpled tubes with both arrangements offer higher heat transfer rates compared to the plain tube and the dimpled tube with staggered arrangement shows an advantage on the basis of heat transfer enhancement over the dimpled tube with aligned arrangement. The increase in heat transfer rate with reducing pitch ratio is due to the higher turbulent intensity imparted to the flow between the dimple surfaces. The mean heat transfer rate offered by the dimpled tube with staggered arrangement (S-A) at the lowest pitch ratio (PR = 0.6), is higher than those provided by the plain tube and the dimpled tube with aligned arrangement (A-A) at the same PR by around 127% and 8%, respectively. The empirical correlations developed in terms of pitch ratio (PR), Prandtl number (Pr) and Reynolds number, are fitted the experimental data within ±8% and ±2% for Nusselt number (Nu) and friction factor (f), respectively. In addition, the thermal performance factors under an equal pumping power constraint of the dimple tubes for both dimpled-surface arrangements are also determined.

Sign in / Sign up

Export Citation Format

Share Document