Experimental Investigation of Diesel Engine Performance and Emission Characteristics Fuelled by Jojoba/Diesel Blend and Sunflower Oil

2009 ◽  
Author(s):  
M. S. Shehata ◽  
S. M. Abdel Razek
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Sunflower Oil ◽  
Engine Performance ◽  
Pressure Change ◽  
High Viscosity ◽  
Maximum Pressure ◽  
Performance And Emission ◽  
Brake Mean Effective Pressure ◽  
Biodiesel Fuels

Experimental study has been carried out to investigate performance parameters, emissions, cylinder pressure, exhaust and wall temperatures at different engine speeds and different percentage of EGR using sunflower and jojoba/diesel (B20) blend in comparison to diesel fuel. Sunflower oil and B20 were selected for the study because of its being widely used in Egypt and world. Tests were conducted for three different fuels with different engine speeds. Also, series of tests were conducted at same previous conditions with different percentage of exhaust gas recirculation (EGR) rates from 0 to 12% of inlet mass of air fresh charge. Results indicate that sunflower or B20 blend gives lower brake thermal efficiency, brake power, brake mean effective pressure, and higher BSFC due to lower heating value compared to diesel fuel. Sunflower or B20 blend gives lower NOX concentration due to lower gases temperature. Sunflower or B20 blend gives higher wall/exhaust temperatures due to incomplete combustion inside engine cylinder. Sunflower or B20 blend gives higher CO and CO2 concentrations due to higher carbon/hydrogen ratio. The position of maximum pressure change for diesel fuel is earlier than for sunflower and B20 blend. The results show that sunflower and B20 blend are promising as alternatives fuel for diesel engine. One of the main advantages of vegetable oil is not requiring significant modification of existing engine hard wares. On contrast, the main disadvantages of biodiesel fuels are high viscosity, drying with time, thickening in cold conditions, flow and atomization characteristics.

scholarly journals THE EFFECT OF DIESEL-BIODIESEL BLENDS ON THE PERFORMANCE AND EXHAUST EMISSIONS OF A DIRECT INJECTION OFF-ROAD DIESEL ENGINE

Transport ◽  
2014 ◽  
Vol 29 (4) ◽  
pp. 440-448 ◽  
Author(s):  
Tomas Mickevičius ◽  
Stasys Slavinskas ◽  
Slawomir Wierzbicki ◽  
Kamil Duda
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Direct Injection ◽  
Engine Performance ◽  
Exhaust Emissions ◽  
Bench Test ◽  
Maximum Pressure ◽  
Cylinder Pressure ◽  
Biodiesel Blends ◽  
Performance And Emission

This paper presents a comparative analysis of the diesel engine performance and emission characteristics, when operating on diesel fuel and various diesel-biodiesel (B10, B20, B40, B60) blends, at various loads and engine speeds. The experimental tests were performed on a four-stroke, four-cylinder, direct injection, naturally aspirated, 60 kW diesel engine D-243. The in-cylinder pressure data was analysed to determine the ignition delay, the Heat Release Rate (HRR), maximum in-cylinder pressure and maximum pressure gradients. The influence of diesel-biodiesel blends on the Brake Specific Fuel Consumption (bsfc) and exhaust emissions was also investigated. The bench test results showed that when the engine running on blends B60 at full engine load and rated speed, the autoignition delay was 13.5% longer, in comparison with mineral diesel. Maximum cylinder pressure decreased about 1–2% when the amount of Rapeseed Methyl Ester (RME) expanded in the diesel fuel when operating at full load and 1400 min–1 speed. At rated mode, the minimum bsfc increased, when operating on biofuel blends compared to mineral diesel. The maximum brake thermal efficiency sustained at the levels from 0.3% to 6.5% lower in comparison with mineral diesel operating at full (100%) load. When the engine was running at maximum torque mode using diesel – RME fuel blends B10, B20, B40 and B60 the total emissions of nitrogen oxides decreased. At full and moderate load, the emission of carbon monoxide significantly raised as the amount of RME in fuel increased.

scholarly journals An investigation of effect of biodiesel and aviation fuel jeta-1 mixtures performance and emissions on diesel engine

2014 ◽  
Vol 18 (1) ◽  
pp. 239-247 ◽  
Author(s):  
Hasan Yamik
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Chemical Properties ◽  
Engine Performance ◽  
Combustion Efficiency ◽  
Aviation Fuel ◽  
Aviation Industry ◽  
Performance And Emission ◽  
Performance And Emissions ◽  
Biodiesel Fuels

Biodiesel is an alternative fuel for diesel engines which doesn?t contain pollutants and sulfur; on the contrary it contains oxygen. In addition, both physical and chemical properties of sunflower oil methyl ester (SME) are identical to diesel fuel. Conversely, diesel and biodiesel fuels are widely used with some additives to reduce viscosity, increase the amount of cetane, and improve combustion efficiency. This study uses diesel fuel, SME and its mixture with aviation fuel JetA-1 which are widely used in the aviation industry. . Fuel mixtures were used in 1-cylinder, 4-stroke diesel engine under full load and variable engine speeds. In this experiment, engine performance and emission level are investigated. As a conclusion, as the JetA-1 ratio increases in the mixture, lower nitrogen oxide (NOx) emission is measured. Also, specific fuel consumption is lowered.

scholarly journals A Review on the Thermochemical Recycling of Waste Tyres to Oil for Automobile Engine Application

Energies ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3837
Author(s):  
Mohammad I. Jahirul ◽  
Farhad M. Hossain ◽  
Mohammad G. Rasul ◽  
Ashfaque Ahmed Chowdhury
Keyword(s):  
Diesel Engine ◽  
Engine Performance ◽  
Calorific Value ◽  
High Viscosity ◽  
Combustion Efficiency ◽  
Fuel Additive ◽  
Pyrolysis Oil ◽  
Performance And Emission ◽  
Automobile Engines ◽  
Direct Use

Utilising pyrolysis as a waste tyre processing technology has various economic and social advantages, along with the fact that it is an effective conversion method. Despite extensive research and a notable likelihood of success, this technology has not yet seen implementation in industrial and commercial settings. In this review, over 100 recent publications are reviewed and summarised to give attention to the current state of global tyre waste management, pyrolysis technology, and plastic waste conversion into liquid fuel. The study also investigated the suitability of pyrolysis oil for use in diesel engines and provided the results on diesel engine performance and emission characteristics. Most studies show that discarded tyres can yield 40–60% liquid oil with a calorific value of more than 40 MJ/kg, indicating that they are appropriate for direct use as boiler and furnace fuel. It has a low cetane index, as well as high viscosity, density, and aromatic content. According to diesel engine performance and emission studies, the power output and combustion efficiency of tyre pyrolysis oil are equivalent to diesel fuel, but engine emissions (NOX, CO, CO, SOX, and HC) are significantly greater in most circumstances. These findings indicate that tyre pyrolysis oil is not suitable for direct use in commercial automobile engines, but it can be utilised as a fuel additive or combined with other fuels.

scholarly journals Performance Assessment of DI-Diesel Engine using the Blend of Sunflower Oil and Rice Bran Oil

2019 ◽  
Vol 8 (4) ◽  
pp. 4048-4052
Keyword(s):  
Diesel Engine ◽  
Sunflower Oil ◽  
Fuel Injection ◽  
Rice Bran Oil ◽  
Engine Performance ◽  
Performance And Emission ◽  
Animal Fats ◽  
Di Diesel Engine ◽  
Hc Emissions ◽  
Direct Fuel Injection

Biodiesel, a derivative of vegetable oils and animal fats, is used nowadays as an alternative renewable and sustainable fossil fuel. In this work, the investigation of manufacture, characterization, and results of biodiesel blends are carried out using two important feedstock’s, sunflower oil and ricebran oil on engines. For the collective advantageous of sunflower oil and ricebran oil, the two biodiesels are combined together and the mixture is analysed to assess the engine performance and emission characteristics. NaOH catalyzed transesterification process is used for producing the Biodiesels A 4.4 kW, four-stroke, single-cylinder and direct fuel injection diesel engine is used for measuring physic-chemical with full load and varying speed conditions and using the specifications of ASTM D6751 standard, the properties are compared. It is observed that the Biodiesel mixtures produce a low brake torque and high brake-specific fuel consumption (BSFC) in addition to the reduction of CO and HC emissions. NOx, however, is reduced considerably with the improvement of brake thermal efficiency. The Performance analysis indicates that the mixture of sunflower oil and ricebran oil improves performance and emission characterizes over sunflower oil and ricebran oil biodiesel when they are unmixed..

Biofuel (Cooking Oil) Blends Contribution in DI Diesel Engine – Performance & Emission Study

2014 ◽  
Vol 984-985 ◽  
pp. 839-844
Author(s):  
Natesan Kanthavelkumaran ◽  
P. Seenikannan
Keyword(s):  
Diesel Engine ◽  
Rice Bran ◽  
Diesel Fuel ◽  
Rice Bran Oil ◽  
Direct Injection ◽  
Research Work ◽  
Engine Performance ◽  
Performance And Emission ◽  
Emission Study ◽  
Ci Engines

In present scenario researchers focusing the alternate sources of petroleum products. Based on this, current research work focused the emission study of its characteristics and potential as a substitute for Diesel fuel in CI engines. Current research biodiesel is produced by base catalyzed transesterification of rice bran oil is known as Rice Bran Oil Methyl Ester (Biofuel). In this research various proportions of Biofuel and Diesel are prepared on volume basis. It is used as fuels in a four stroke single cylinder direct injection Diesel engine to study the performance and emission characteristics of these fuels. Varieties of results obtained, that shows around 50% reduction in smoke, 33% reduction in HC and 38% reduction in CO emissions. In result discussion a different blends of the brake power and BTE are reduced nearly 2 to 3% and 3 to 4% respectively around 5% increase in the SFC. Therefore it is accomplished from the this experimental work that the blends of Biofuel and Diesel fuel can successfully be used in Diesel engines as an alternative fuel without any modification in the engine. It is also environment friendly blended fuel by the various emission standards.

scholarly journals Performance of Diesel Engine using Bio-Fuel From Sesame Oil

2019 ◽  
Vol 8 (10) ◽  
pp. 1554-1558 ◽  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fossil Fuels ◽  
Industrial Revolution ◽  
Engine Performance ◽  
High Standard ◽  
Alternative Fuel ◽  
Exhaust Emissions ◽  
High Viscosity ◽  
Sesame Oil

Energy has become a crucial factor for humanity to continue the economic growth and maintain high standard of living especially after industrial revolution. “Fossil fuels are still the main source of energy. But the endless consumption of fossil fuels will bring the reserve to an end in near future. As a result fuel prices are soaring because of diminishing supply than demand. So researchers world over are in constant search of alternate fuels in the last three to four years, aimed at reducing CO2 emissions and global dependency on fossil fuels. The use of vegetable oils as a fuel in diesel engine causes some problems due to their high viscosity compared with conventional diesel fuel. Various techniques and methods are used to solve the problems resulting from high viscosity. One of these techniques is blending of fuel. In this study, a mix of 5%, 10%,15%, 20%, 25% sesame oil and diesel fuel was used as alternative fuel in a direct injection diesel engine. Diesel engine performance and exhaust emissions were investigated and compared with the diesel fuel in a diesel engine. The experimental results show that the engine power and torque of the mixture of sesame oil diesel fuel are close to the values obtained from diesel fuel and the amount of exhaust emissions are lower than those of diesel fuel. Hence it is seen that mix of sesame oil 20% and 80% diesel fuel can be used as an alternative fuel successfully in a diesel engine without any modification and also it is an environmental friendly” fuel in terms of emission parameters.

scholarly journals Experimental Investigation of Performance and Emission Characteristics of IDI Diesel Engine Using Homogenized Water in Bio-Diesel Emulsion

2018 ◽  
Vol 225 ◽  
pp. 04022
Author(s):  
Zainal Ambri Abdul Karim ◽  
Mohammed Yahaya Khan
Keyword(s):  
Diesel Engine ◽  
Nitrogen Oxides ◽  
Diesel Fuel ◽  
Load Condition ◽  
Engine Performance ◽  
Gas Temperature ◽  
Simultaneous Reduction ◽  
Performance And Emission ◽  
Increase With Increase ◽  
Smoke Opacity

Water in diesel emulsion when used as fuel in diesel engine has shown simultaneous reduction in both nitrogen oxides and particulate matters. However, when water in bio-diesel emulsion is used, the effect of simultaneous reduction of nitrogen oxides and particulate reduction is not achieved. The current study aims at investigating the diesel engine performance and exhaust emissions using water in bio-diesel fuel prepared by a homogenizer that produced micro-water particles in the emulsion. A 1.8L indirect injection diesel engine was operated using bio-diesel fuel which contains 95% diesel and 5% palm oil methyl ester, mixed with 5%, 10% and 20% by volume of water. Engine testing was conducted at full load condition with the engine speeds ranges from 1000 to 4000 rpm. Torque, engine speed and fuel consumption were measured along with emissions of NOx, CO, CO2, HC, O2. The results showed small reduction in brake power, 1.4% and 2.1% for WBDE-5 and WBDE-10 respectively, at maximum torque. While, reduction in exhaust gas temperature, CO2 and smoke opacity for all the tested emulsions were exhibited. On the other hand, NOx was found to increase with increase in water contents due to the higher oxygen content in the bio-diesel fuel. WBDE-20 showed the worst efficacy due to having water content of 20% by volume.

Engine Performance and Emission of Emulsified Biodiesel

2014 ◽  
Vol 607 ◽  
pp. 588-593 ◽  
Author(s):  
Amir Aziz ◽  
Ahmad Fitri Yusof ◽  
Rizalman Mamat ◽  
W.N. Azeem
Keyword(s):  
Diesel Engine ◽  
Water Content ◽  
Experimental Work ◽  
Diesel Fuel ◽  
Engine Performance ◽  
Emission Characteristics ◽  
Nox Formation ◽  
Performance And Emission ◽  
Set Up ◽  
Emulsified Biodiesel

An emulsion of biodiesel and water is one of the possible approaches that have been used to overcome diesel engine pollution. In this work, the performance and emission characteristics of a 4-cylinder diesel engine using pure diesel, biodiesel B20 and emulsified biodiesel were investigated. Emulsified biodiesel containing 5 % and 10 % water were utilize for the engine tests. During the experimental work, the engine was set-up at 2500 rpm and 20 % to 60 % loads. The result shows the reduction in NOx formation when the water content in emulsified biodiesel increased from 5 % to 10%. For the performance, there were no significant differences between the engine break powers measured for emulsified biodiesel containing 5% water and diesel fuel.

scholarly journals Production, Quantitative Analysis of Fatty Acids, Engine Performance and Emission Characteristics of Biodiesel Fuel Derived from Virgin Coconut Oil

2020 ◽  
Vol 5 (7) ◽  
pp. 1397-1404
Author(s):  
Alex Y ◽  
Roji George Roy
Keyword(s):  
Diesel Engine ◽  
Physicochemical Properties ◽  
Diesel Fuel ◽  
Diesel Engines ◽  
Engine Performance ◽  
Coconut Oil ◽  
Biodiesel Fuel ◽  
Emission Characteristics ◽  
Virgin Coconut Oil ◽  
Performance And Emission

Biodiesel has become more attractive recently, because of its environmental benefits and the fact that it is made from renewable resources. Over the past few decades, most of the countries depending on diesel engines for transportation. Some of its valuable advantages like highest thermal efficiency made it very popular. At the same time, the cost of diesel fuel is increasing, due to the depletion of fossil fuels. In this current scenario, we need an alternative fuel instead of diesel fuel. Many of the researchers have successfully placed several works on generating energy from different types of alternative sources including solar and some kind of conversion processes including renewable agricultural products into liquid fuel. One of the biggest challenges for developing countries in relation to energy consumption is to develop and implement technologies that help to improve efficiency of automobile engines, also to reduce the emissions of harmful gases and particulate matters. In order to avoid environmental impacts, emissions are reduced or eliminated by introducing renewable energy resources. The present research chronicles the production and testing of renewable biodiesel fuel derived from virgin coconut oil on a diesel engine, to analyses the engine performance and emission characteristics. In the first phase of work, production of biodiesel fuel from virgin coconut oil using transeterification process with two types of catalysts (homogenous and heterogeneous). The preliminary results shows that, with the addition of homogenous catalyst called Potassium Hydroxide (KOH) with methanol shows much higher activity than that of heterogeneous catalysts, and it shows more similar properties with diesel fuel. The results obtained from the chemical test and physicochemical properties of transesterified biodiesel fuel clearly proves the above-mentioned statement. The chemical tests such as GCMS and FT-IR clearly shows that the biodiesel fuel has sufficient amount of volatile components and functional groups. Then, physicochemical properties include, Fire point, Flashpoint, density, and viscosity were analyzed. Finally, Engine performance and Emission characteristics were analysed to confirm, whether this biodiesel fuel is suitable for diesel engines, without any engine modifications. It was found to be, the transesterified virgin coconut oil biodiesel has similar properties to that of the diesel fuel. From the physiochemical properties and engine performance clearly shows that, coconut oil biodiesel is suitable for diesel engine on blending, at a blending percentage level of 20% with conventional diesel fuel. Since the obtained transesterified biofuel can be used as an alternative fuel for diesel engines. The several journal reports and find outs from experimental investigation clearly depicts that the efficiency of the transesterified biofuel mainly depends upon the amount of catalyst adding and type of catalysts present in the biofuel, whether it is homogenous or heterogeneous catalyst is suitable with methanol. Finally, from the analysis made from biodiesel fuel. Coconut Oil Biodiesel fuel has less emission characteristics than that of the diesel fuels.

Sign in / Sign up

Export Citation Format

Share Document