Combustion and Emissions of Jet-A and N-Butanol in RCCI Operation

2017 ◽  
Author(s):  
Valentin Soloiu ◽  
Jose Moncada ◽  
Remi Gaubert ◽  
Spencer Harp ◽  
Kyle Flowers ◽  
...  
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Cetane Number ◽  
Combustion Stability ◽  
Emissions Control ◽  
Local Pressure ◽  
Reactivity Controlled Compression Ignition ◽  
Ultra Low Sulfur Diesel ◽  
Pressure Maximum ◽  
Low Sulfur

Jet-A was investigated in RCCI (Reactivity Controlled Compression Ignition) given that the fuel is readily available and has a similar cetane number compared to ultra-low sulfur diesel (ULSD#2). To promote emissions’ control, RCCI was conducted with direct injection (DI) of Jet-A and PFI (port fuel injection) of n-butanol. Combustion and emission characteristics of Jet-A RCCI were investigated for a medium duty DI experimental engine operated at constant boost and 30% EGR rate and compared to ULSD#2 RCCI and single-fuel ULSD#2 operation. DI fuel was injected at 5 CAD ATDC and constant rail pressure of 1500 bar. A 20% pilot by mass was added and investigated at timings from 15 to 5 CAD BTDC for combustion stability. The results showed that the effect of the pilot injection on Jet-A combustion was not as prominent as compared to that of ULSD#2, suggesting a slightly different spray and mixture formation. Ignition delay for Jet-A was 15–20% shorter compared to ULSD#2 in RCCI. When the pilot was set to 5 CAD BTDC, CA50 phased for ULSD#2 RCCI by 3 CAD later when compared to Jet-A RCCI. After TDC, the local pressure maximum for ULSD#2 RCCI decreased by 3 bar, resulting from a 15% difference in peak heat release rate between ULSD#2 and Jet-A in RCCI at the same pilot timing. NOx and soot levels were reduced by a respective maximum of 35% and 80% simultaneously in Jet-A RCCI mode compared to single-fuel ULSD#2, yet, were higher compared to ULSD#2 RCCI. Ringing intensity was maintained at similar levels and energy specific fuel consumption (ESFC) improved by at least 15% for Jet-A compared to ULSD#2 in RCCI. Mechanical efficiencies additionally improved at earlier pilot timing by 2%. In summary, Jet-A RCCI allowed for emissions control and increased fuel efficiencies compared to single fuel ULSD#2, however, injection should be further tweaked in order to reach lower soot levels.

RCCI of Synthetic Kerosene With PFI of N-Butanol-Combustion and Emissions Characteristics

2015 ◽  
Author(s):  
Valentin Soloiu ◽  
Martin Muiños ◽  
Tyler Naes ◽  
Spencer Harp ◽  
Marcis Jansons
Keyword(s):  
Thermal Efficiency ◽  
Fuel Injection ◽  
Direct Injection ◽  
Cetane Number ◽  
Engine Performance ◽  
Reactivity Controlled Compression Ignition ◽  
Ultra Low Sulfur Diesel ◽  
Indicated Mean Effective Pressure ◽  
Soot Emissions ◽  
Low Sulfur

In this study, the combustion and emissions characteristics of Reactivity Controlled Compression Ignition (RCCI) obtained by direct injection (DI) of S8 and port fuel injection (PFI) of n-butanol were compared with RCCI of ultra-low sulfur diesel #2 (ULSD#2) and PFI of n-butanol at 6 bar indicated mean effective pressure (IMEP) and 1500 rpm. S8 is a synthetic paraffinic kerosene (C6–C18) developed by Syntroleum and is derived from natural gas. S8 is a Fischer-Tropsch fuel that contains a low aromatic percentage (0.5 vol. %) and has a cetane number of 63 versus 47 of ULSD#2. Baselines of DI conventional diesel combustion (CDC), with 100% ULSD#2 and also DI of S8 were conducted. For both RCCI cases, the mass ratio of DI to PFI was set at 1:1. The ignition delay for the ULSD#2 baseline was found to be 10.9 CAD (1.21 ms) and for S8 was shorter at 10.1 CAD (1.12 ms). In RCCI, the premixed charge combustion has been split into two regions of high temperature heat release, an early one BTDC from ignition of ULSD#2 or S8, and a second stage, ATDC from n-butanol combustion. RCCI with n-butanol increased the NOx because the n-butanol contains 21% oxygen, while S8 alone produced 30% less NOx emissions when compared to the ULSD#2 baseline. The RCCI reduced soot by 80–90% (more efficient for S8). However, S8 alone showed a considerable increase in soot emissions compared with ULSD#2. The indicated thermal efficiency was the highest for the ULSD#2 and S8 baseline at 44%. The RCCI strategies showed a decrease in indicated thermal efficiency at 40% ULSD#2-RCCI and 42% and for S8-RCCI, respectively. S8 as a single fuel proved to be a very capable alternative to ULSD#2 in terms of combustion performance nevertheless, exhibited higher soot emissions that have been mitigated with the RCCI strategy without penalty in engine performance.

RCCI Investigations With n-Butanol and ULSD

2019 ◽  
Author(s):  
Valentin Soloiu ◽  
Cesar E. Carapia ◽  
Justin T. Wiley ◽  
Jose Moncada ◽  
Remi Gaubert ◽  
...  
Keyword(s):  
Combustion Chamber ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection Timing ◽  
Compression Ignition ◽  
Reactivity Controlled Compression Ignition ◽  
Ultra Low Sulfur Diesel ◽  
Constant Volume Combustion Chamber ◽  
Soot Emissions ◽  
Low Sulfur

Abstract The focus of this study is to reduce harmful NOx and soot emissions of a compression ignition (CI) engine using reactivity-controlled compression ignition (RCCI) with n-Butanol. RCCI was achieved with the port fuel injection (PFI) of a low reactivity fuel, n-butanol, and a direct injection (DI) of the highly reactive fuel ULSD #2 (Ultra Low Sulfur Diesel) into the combustion chamber. The reactivity, ID, and CD where determined using a Constant Volume Combustion Chamber (CVCC) where ID for n-butanol was found to be 15 times slower than ULSD. The emissions and combustion analysis was conducted at 1500 RPM at an experimental low engine load of 4 bar IMEP; the baseline for emissions comparison was conducted using conventional diesel combustion (CDC) with an injection timing of 16° BTDC at a rail pressure of 800 bar. RCCI was conducted utilizing 75% by mass PFI of n-butanol with 25% ULSD DI, showed a simultaneous reduction of both NOx and soot emissions at a rate of 96.2% and 98.7% respectively albeit with an increase in UHC emissions by a factor of 5. Ringing Intensity was also significantly reduced for Bu75ULSD25 (RCCI Experiment) with a reduction of 62.1% from CDC.

An integrated effort of medium reactivity fuel, in-cylinder, and after-treatment strategies to demonstrate potential reduction in challenging emissions of reactivity controlled compression ignition combustion

2019 ◽  
Vol 234 (5) ◽  
pp. 1260-1278
Author(s):  
R Murugan ◽  
D Ganesh ◽  
G Nagarajan
Keyword(s):  
Carbon Monoxide ◽  
Direct Injection ◽  
Cetane Number ◽  
Combustion Process ◽  
Oxidation Catalyst ◽  
Compression Ignition ◽  
Reactivity Controlled Compression Ignition ◽  
Potential Reduction ◽  
Carbon Monoxide Emission ◽  
Compression Ignition Combustion

Previous studies on reactivity controlled compression ignition combustion indicated that, reducing the hydrocarbon and carbon monoxide emissions at low load conditions still remains a challenge because of lower in-cylinder temperatures due to lower global reactivity gradient and reduced oxidation process. Research in this direction has not been reported so far and with this motivation, an attempt has been made to increase the global reactivity gradient and oxidation of fuel–air mixture by converting the low reactivity fuel methanol into medium reactivity fuel. This is achieved by mixing high octane oxygenated fuel, methanol (Octane Number: 110), with an oxygenated better cetane and volatility fuels like polyoxymethylene dimethyl ether (Cetane Number: 78) and isobutanol (Cetane Number: 15). The medium reactivity fuel with multiple direct injection of diesel fuel timed the combustion of dual fuel–air mixture to avoid too late or too advanced combustion which are the prime factors in controlling the unburnt emissions in a low temperature combustion process. Four medium reactivity fuel samples, M80IB20, M60IB40, M90P10, and M80P20, on percentage volume basis have been prepared and tested on the modified on-road three-cylinder turbocharged common rail direct injection diesel engine to demonstrate higher indicated thermal efficiency and potential reduction in unburnt and oxides of nitrogen/particulate matter emissions from reactivity controlled compression ignition combustion. Experimental results show that, use of medium reactivity fuel with optimized diesel injection strategy resulted in 66% decrease in hydrocarbon emission and 74% decrease in carbon monoxide emission by enhancing the oxidation of fuel–air mixture at lower temperatures which is evidently noticed in the combustion characteristics. Further reduction in hydrocarbon and carbon monoxide emission of about 90% has been achieved by integrating the diesel oxidation catalyst with the engine.

Computational optimization of reactivity controlled compression ignition combustion to achieve high efficiency and clean combustion

2020 ◽  
pp. 146808742093173 ◽  
Author(s):  
Avilash Jain ◽  
Anand Krishnasamy ◽  
Pradeep V
Keyword(s):  
Neural Network ◽  
Artificial Neural Network ◽  
Fuel Injection ◽  
Direct Injection ◽  
Network Models ◽  
Compression Ignition ◽  
Neural Network Models ◽  
Reactivity Controlled Compression Ignition ◽  
Artificial Neural ◽  
Artificial Neural Network Models

One of the major limitations of reactivity controlled compression ignition is higher unburned hydrocarbon and carbon monoxide emissions and lower thermal efficiency at part load operating conditions. In the present study, a combined numerical approach using a commercial three-dimensional computational fluid dynamics code CONVERGE along with artificial neural network and genetic algorithm is presented to address the above limitation. A production light-duty diesel engine is modified to run in reactivity controlled compression ignition by replacing an existing mechanical fuel injection system with a flexible electronic port fuel injection and common rail direct injection systems. The injection schedules of port fuel injection and direct injection injectors are controlled using National Instruments port and direct injection driver modules. Upon validation of combustion and emission parameters, parametric investigations are carried out to establish the effects of direct-injected diesel fuel timing start of injection (SOI), premixed fuel ratio and intake charge temperature on the engine performance and emissions in reactivity controlled compression ignition. The results obtained show that the start of injection timing and intake charge temperature significantly influence combustion phasing, while the premixed fuel ratio controls mixture reactivity and combustion quality. By utilizing the data generated with the validated computational fluid dynamics models, the artificial neural network models are trained to predict the engine exhaust emissions and efficiency. The artificial neural network models for gross indicated efficiency and oxides of nitrogen (NOx) are then coupled with genetic algorithm to maximize gross indicated efficiency while keeping the NOx and soot emissions within Euro VI emission limits. By optimizing the start of injection timing, premixed fuel ratio and intake charge temperature simultaneously using the artificial neural network models coupled with genetic algorithm, 19% improvement in gross indicated efficiency, 60% and 64% reduction in hydrocarbon and carbon monoxide emissions, respectively, are obtained in reactivity controlled compression ignition compared to the baseline case.

Investigation of the Effect of Injection and Control Strategies on Combustion Instability in Reactivity-Controlled Compression Ignition Engines

2015 ◽  
Vol 138 (1) ◽  
Author(s):  
David T. Klos ◽  
Sage L. Kokjohn
Keyword(s):  
Direct Injection ◽  
Combustion Instability ◽  
Pressure Rise ◽  
Operating Conditions ◽  
Combustion Stability ◽  
Cfd Modeling ◽  
Surface Model ◽  
Injection Timing ◽  
Compression Ignition ◽  
Reactivity Controlled Compression Ignition

This paper uses detailed computational fluid dynamics (CFD) modeling with the kiva-chemkin code to investigate the influence of injection timing, combustion phasing, and operating conditions on combustion instability. Using detailed CFD simulations, a large design of experiments (DOE) is performed with small perturbations in the intake and fueling conditions. A response surface model (RSM) is then fit to the DOE results to predict cycle-to-cycle combustion instability. Injection timing had significant tradeoffs between engine efficiency, emissions, and combustion instability. Near top dead center (TDC) injection timing can significantly reduce combustion instability, but the emissions and efficiency drop close to conventional diesel combustion levels. The fuel split between the two direct injection (DI) injections has very little effect on combustion instability. Increasing exhaust gas recirculation (EGR) rate, while making adjustments to maintain combustion phasing, can significantly reduce peak pressure rise rate (PPRR) variation until the engine is on the verge of misfiring. Combustion phasing has a very large impact on combustion instability. More advanced phasing is much more stable, but produces high PPRRs, higher NOx levels, and can be less efficient due to increased heat transfer losses. The results of this study identify operating parameters that can significantly improve the combustion stability of dual-fuel reactivity-controlled compression ignition (RCCI) engines.

Cotton Seed FAME Combustion and Emissions Research in a DI Diesel Engine

2013 ◽  
Author(s):  
Valentin Soloiu ◽  
Jabeous Weaver ◽  
Henry Ochieng ◽  
Marvin Duggan ◽  
Sherwin Davoud ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Cotton Seed ◽  
Methyl Esters ◽  
Direct Injection ◽  
Mechanical Efficiency ◽  
Ultra Low Sulfur Diesel ◽  
Indicated Mean Effective Pressure ◽  
A Value ◽  
Carbon Dioxide Co2 ◽  
Low Sulfur

This study investigates the combustion characteristics of cotton seed fatty acid methyl esters (FAME), with C100 (100% cotton seed biodiesel) and C20 (20% cotton seed biodiesel, 80% ultra-low sulfur diesel #2), in a direct injection diesel engine and compares the results with ultra-low sulfur diesel #2 (ULSD#2). The dynamic viscosity of C100 was found to meet the American Society for Testing and Materials (ASTM) standard. The lower heating value obtained for C100 was 37.7 MJ/kg, compared to 42.7 MJ/kg for ULSD#2. ULSD#2 and C100 displayed ignition delays of 9.6 crank angle degrees (CAD) and 7 CAD representing 1.14 ms and 0.83 ms respectively and a combustion time of 4ms (35 CAD) at 1400 rpm and 8 bar indicated mean effective pressure (IMEP) (100% load). The apparent heat release of the tested fuels at 8 bar IMEP showed both a premixed and diffusion phase and produced maximum values of 122 and 209 J/CAD for C100 and ULSD#2 respectively, with a decreasing trend occurring with increase in percentage of FAME. The 50% mass burnt (CA50) for 100% biodiesel was found to be 3 CAD advanced, compared with ULSD#2. The maximum total heat flux rates showed a value of 3.2 MW/m2 for ULSD#2 at 8 bar IMEP with a 6% increase observed for C100. Mechanical efficiency of ULSD#2 was 83% and presented a 5.35% decrease for C100, while the overall efficiency was 36% for ULSD#2 and 33% for C100 at 8 bar IMEP. The nitrogen oxides (NOx) for C100 presented an 11% decrease compared with ULSD#2. Unburned hydrocarbons value (UHC) for ULSD#2 was 2.8 g/kWh at 8 bar IMEP, and improved by 18% for C100. The carbon monoxide (CO) emissions for C100 decreased by 6% when compared to ULSD#2 at 3 bar IMEP but were relatively constant at 8 bar IMEP, presenting a value of 0.82 g/kWh for both fuels. The carbon dioxide (CO2) emissions for C100 increased by 1% compared with ULSD#2, at 3 bar IMEP. The soot value for ULSD#2 was 1.5 g/kWh and presented a 42% decrease for C100 at 8 bar IMEP. The results suggest a very good performance of cotton seed biodiesel, even at very high content of 100%, especially on the emissions side that showed decreasing values for regulated and non-regulated species.

Effect of Inlet Air Temperature on Auto-Ignition of Fuels With Different Cetane Number and Volatility

2011 ◽  
Author(s):  
Chandrasekharan Jayakumar ◽  
Ziliang Zheng ◽  
Umashankar M. Joshi ◽  
Walter Bryzik ◽  
Naeim A. Henein ◽  
...  
Keyword(s):  
Air Temperature ◽  
Ignition Delay ◽  
Fuel Injection ◽  
Cetane Number ◽  
Delay Period ◽  
Inlet Temperature ◽  
Ignition Process ◽  
Ultra Low Sulfur Diesel ◽  
Auto Ignition ◽  
Ignition Delay Period

This paper investigates the effect of air inlet temperature on the auto-ignition of fuels that have different CN and volatility in a single cylinder diesel engine. The inlet air temperature is varied over a range of 30°C to 110°C. The fuels used are ultra-low-sulfur-diesel (ULSD), JP-8 (two blends with CN 44.1 & 31) and F-T SPK. Detailed analysis is made of the rate of heat release during the ignition delay period, to determine the effect of fuel volatility and CN on the auto-ignition process. A STAR-CD CFD model is applied to simulate the spray behavior and gain more insight into the processes that immediately follow the fuel injection including evaporation, start of exothermic reactions and the early stages of combustion. The mole fractions of different species are determined during the ignition delay period and their contribution in the auto-ignition process is examined. Arrhenius plots are developed to calculate the global activation energy for the auto-ignition reactions of these fuels. Correlations are developed for the ID and the mean air temperature and pressure.

Combustion and Emissions Characterization of Soy Methyl Ester Biodiesel Blends in an Automotive Turbocharged Diesel Engine

2009 ◽  
Author(s):  
Benjamin W. Moscherosch ◽  
Christopher J. Polonowski ◽  
Scott A. Miers ◽  
Jeffrey D. Naber
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Diesel Engines ◽  
Ignition Delay ◽  
Alternative Fuels ◽  
Cetane Number ◽  
Biodiesel Blends ◽  
Ultra Low Sulfur Diesel ◽  
Soy Methyl Ester ◽  
Low Sulfur

Recent increases in petroleum fuel costs, CAFE standards, and environmental concerns about CO2 emissions from petroleum based fuels have created an increased opportunity for diesel engines and renewable alternative fuels such as biodiesel. Additionally, the Environmental Protection Agencies Tier II heavy duty and light duty emissions regulations require significant reductions in NOx and diesel particulate matter emissions for diesel engines. As a result, the diesel engine and aftertreatment system is a highly calibrated system that is sensitive to changing fuel characteristics. This study focuses on the impact of soy methyl ester biodiesel blends on combustion performance, carbonaceous soot matter and NOX emissions. Tests were completed with an I4 1.9L, turbocharged, high speed, direct injection diesel engine using commercially available 15 ppm ultra low sulfur diesel, a soy methyl ester B20 (20% biodiesel and 80% ultra low sulfur diesel) biodiesel blend and a pure soy methyl ester biodiesel. Results show a reduction in NOx and carbonaceous soot matter emissions and an increase in brake specific fuel consumption with the use of biodiesel. Further, traditional methodology assumes that diesel fuels with a high cetane number have a reduced ignition delay. However, results from this study show the cetane number is not the only parameter effecting ignition delay.

Sign in / Sign up

Export Citation Format

Share Document