Experimental Study on the Thermal Properties and Stability of Hybrid Nanofluids and Evaluation of its Heat Exchange Efficiency

2020 ◽  
Author(s):  
Yubai Xiao ◽  
Hu Zhang ◽  
Junmei Wu
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Heat Transfer Performance ◽  
Volume Concentration ◽  
High Thermal Conductivity ◽  
Transfer Efficiency ◽  
Working Fluid ◽  
Transfer Performance ◽  
Heat Transfer Efficiency ◽  
Hybrid Nanofluids

Abstract In recent years, hybrid nanofluids, as a new kind of working fluid, have been widely studied because they possessing better heat transfer performance than single component nanofluids when prepared with proper constituents and proportions. The application of hybrid nanofluids in nuclear power system as a working fluid is an effective way of improving the capability of In-Vessel Retention (IVR) when the reactor is in a severe accident. In order to obtain hybrid nanofluids with excellent heat transfer performance, three kinds of hybrid nanofluids with high thermal conductivity are measured by transient plane source method, and their viscosity and stability are also investigated experimentally. These experimental results are used to evaluate the heat transfer efficiency of hybrid nanofluids. The results show that: (1) The thermal conductivity of hybrid nanofluids increases with increasing temperature and volume concentration. When compared to the base fluid, the thermal conductivity of Al2O3-CuO/H2O, Al2O3-C/H2O and AlN-TiO2/H2O nanofluids at 0.25% volume concentration increased by 36%, 24%, and 22%, respectively. (2) Surfactants can improve the stability of hybrid nanofluids. The Zeta potential value is related to the thermal conductivity of the hybrid nanofluids, and it could be used to explain the relationship between the thermal conductivity of the hybrid nanofluids and the dispersion. It also could provide a reference for subsequent screening of high thermal conductivity nanofluids. (3) The addition of C/H2O can effectively reduce the dynamic viscosity coefficient of hybrid nanofluids. (4) The analysis of heat transfer efficiency of the hybrid nanofluids found that both Al2O3-CuO/H2O and Al2O3-C/H2O have better heat transfer ability than water under certain mixing conditions. This study is conducive to further optimizing hybrid nanofluids and its application to the In-Vessel Retention in severe reactor accidents.

An Evaluation of the Application of Nanofluids in Intercooled Cycle Marine Gas Turbine Intercooler

2015 ◽  
Vol 138 (1) ◽  
Author(s):  
Ningbo Zhao ◽  
Xueyou Wen ◽  
Shuying Li
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Gas Turbine ◽  
Heat Transfer Performance ◽  
Volume Concentration ◽  
Inlet Temperature ◽  
Transfer Performance ◽  
Pumping Power ◽  
Flow And Heat Transfer ◽  
Overall Performance

Coolant is one of the important factors affecting the overall performance of the intercooler for the intercooled (IC) cycle marine gas turbine. Conventional coolants, such as water and ethylene glycol, have lower thermal conductivity which can hinder the development of highly effective compact intercooler. Nanofluids that consist of nanoparticles and base fluids have superior properties like extensively higher thermal conductivity and heat transfer performance compared to those of base fluids. This paper focuses on the application of two different water-based nanofluids containing aluminum oxide (Al2O3) and copper (Cu) nanoparticles in IC cycle marine gas turbine intercooler. The effectiveness-number of transfer unit method is used to evaluate the flow and heat transfer performance of intercooler, and the thermophysical properties of nanofluids are obtained from literature. Then, the effects of some important parameters, such as nanoparticle volume concentration, coolant Reynolds number, coolant inlet temperature, and gas side operating parameters on the flow and heat transfer performance of intercooler, are discussed in detail. The results demonstrate that nanofluids have excellent heat transfer performance and need lower pumping power in comparison with base fluids under different gas turbine operating conditions. Under the same heat transfer, Cu–water nanofluids can reduce more pumping power than Al2O3–water nanofluids. It is also concluded that the overall performance of intercooler can be enhanced when increasing the nanoparticle volume concentration and coolant Reynolds number and decreasing the coolant inlet temperature.

scholarly journals A review on the thermal performance of nanofluid inside circular tube with twisted tape inserts

2020 ◽  
Vol 12 (6) ◽  
pp. 168781402092489
Author(s):  
Saadah Ahmad ◽  
Shahrir Abdullah ◽  
Kamaruzzaman Sopian
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Volume Fraction ◽  
Fluid Mixing ◽  
Transfer Efficiency ◽  
Working Fluid ◽  
Twisted Tape ◽  
Transfer Enhancement ◽  
Heat Transfer Efficiency ◽  
Improve Heat Transfer

Working fluid with higher thermal conductivity and tube with better fluid mixing are two crucial elements for heat transfer enhancement in heat exchanger system. Hence, several methods and techniques have been explored to improve heat transfer efficiency, including dispersing nanoparticles into conventional heat transfer fluid and inserting instruments inside the tube of the heat exchanger. Studies have shown that nanofluid can improve heat transfer efficiency of the system due to its higher thermal conductivity and drastic Brownian motion of nanoparticles while inserts within tube can improve heat transfer efficiency by increasing axial velocity of working fluid for better fluid mixing. This article summarized 109 of journals from recent research on heat transfer enhancement of nanofluid flowing inside the tube with inserts as well as discussing the significant parameters that affected the system’s efficiency such as nanoparticles’ volume fraction, Reynolds number and types and configurations of inserts. Ultimately, analysis will be carried out to determine the most suitable modification of twisted tape inserts with the most optimum value of nanoparticle volume fraction for turbulence flow regime. Finally, some problems that need to be solved for future research such as agglomeration and pressure drop are discussed.

scholarly journals Study on Heat Transfer Performance and Anti-Fouling Mechanism of Ternary Ni-W-P Coating

2020 ◽  
Vol 10 (11) ◽  
pp. 3905
Author(s):  
Lu Ren ◽  
Yanhai Cheng ◽  
Jinyong Yang ◽  
Qingguo Wang
Keyword(s):  
Heat Transfer ◽  
Surface Energy ◽  
Transition State ◽  
Heat Transfer Performance ◽  
High Surface ◽  
Deposition Process ◽  
Oxidation Products ◽  
Transfer Efficiency ◽  
Transfer Performance ◽  
Heat Transfer Efficiency

Since the formation of fouling reduces heat transfer efficiency and causes energy loss, anti-fouling is desirable and may be achieved by coating. In this work, a nickel-tungsten-phosphorus (Ni-W-P) coating was prepared on the mild steel (1015) substrate using electroless plating by varying sodium tungstate concentration to improve its anti-fouling property. Surface morphology, microstructure, fouling behavior, and heat transfer performance of coatings were further reported. Also, the reaction path, transition state, and energy gradient change of calcite, aragonite, and vaterite were also calculated. During the deposition process, as the W and P elements were solids dissolved in the Ni crystal cell, the content of Ni element was obviously higher than that of the other two elements. Globular morphology was evenly covered on the surface. Consequently, the thermal conductivity of ternary Ni-W-P coating decreases from 8.48 W/m·K to 8.19 W/m·K with the increase of W content. Additionally, it goes up to 8.93 W/m·K with the increase of heat source temperature 343 K. Oxidation products are always accompanied by deposits of calcite-phase CaCO3 fouling. Due to the low surface energy of Ni-W-P coating, Ca2+ and [CO3]2− are prone to cross the transition state with a low energy barrier of 0.10 eV, resulting in the more formation of aragonite-phase CaCO3 fouling on ternary Ni-W-P coating. Nevertheless, because of the interaction of high surface energy and oxidation products on the bare matrix or Ni-W-P coating with superior W content, free Ca2+ and [CO3]2− can be easy to nucleate into calcite. As time goes on, the heat transfer efficiency of material with Ni-W-P coating is superior to the bare surface.

scholarly journals Effect of Environmental Wind on Performance of a 600MW Direct Air-cooled Unit Based on FLUENT

2019 ◽  
Vol 118 ◽  
pp. 02019
Author(s):  
Junfeng Xu ◽  
Taoying Wang ◽  
Minmin Zhao
Keyword(s):  
Heat Transfer ◽  
Wind Speed ◽  
Flow Field ◽  
Wind Direction ◽  
Heat Transfer Performance ◽  
Air Flow ◽  
Transfer Efficiency ◽  
Windward Side ◽  
Transfer Performance ◽  
Heat Transfer Efficiency

The external flow field of a 600MW air-cooled unit is numerically simulated based on FLUENT. The distribution law of air flow field of air-cooled unit under different wind speed and wind direction conditions is studied. The influence of wind speed and wind direction on the heat transfer performance of air-cooled unit is analyzed. Predict the exhaust pressure of direct air-cooled unit under the influence of environmental wind. The results show that in the +X direction environmental wind, the first row of air-cooled unit on the windward side is prone to backflow; in the +Y direction environmental wind, the first row of air-cooled unit on the windward side is prone to hot air recirculation. As the wind speed increases, the heat transfer efficiency of the air-cooled unit decreases. The dominant wind direction (WNW) environmental wind has the least impact on the heat transfer efficiency, and the furnace wind (+Y direction wind) has the greatest influence on the heat transfer efficiency. To improve the heat transfer performance of the air-cooled unit under windy conditions, it is necessary to narrow the range of the negative pressure zone below the air-cooled unit and increase the cooling air flow rate of the air-cooled unit.

An Evaluation of the Application of Nanofluids in Intercooled Cycle Marine Gas Turbine Intercooler

2015 ◽  
Author(s):  
Ningbo Zhao ◽  
Xueyou Wen ◽  
Shuying Li
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Gas Turbine ◽  
Heat Transfer Performance ◽  
Volume Concentration ◽  
Inlet Temperature ◽  
Transfer Performance ◽  
Pumping Power ◽  
Flow And Heat Transfer ◽  
Overall Performance

Coolant is one of the important factors affecting the overall performance of the intercooler for the intercooled cycle marine gas turbine. Conventional coolants such as water and ethylene glycol have lower thermal conductivity which can hinder the development of highly effective compact intercooler. Nanofluids that consist of nanoparticles and base fluids have superior properties like extensively higher thermal conductivity and heat transfer performance compared to those of base fluids. This paper focuses on the application of two different water-based nanofluids containing aluminum oxide (Al2O3) and copper (Cu) nanoparticles in intercooled cycle marine gas turbine intercooler. The effectiveness-number of transfer unit method is used to evaluate the flow and heat transfer performance of intercooler and the thermophysical properties of nanofluids are obtained from literature. Then the effects of some important parameters such as nanoparticle volume concentration, coolant Reynolds number, coolant inlet temperature and gas side operating parameters on the flow and heat transfer performance of intercooler are discussed in detail. The results demonstrate that nanofluids have excellent heat transfer performance and need lower pumping power in comparison with base fluids under different gas turbine operating conditions. Under the same heat transfer, Cu-water nanofluids can reduce more pumping power than Al2O3-water nanofluids. It is also concluded that the overall performance of intercooler can be enhanced when increasing the nanoparticle volume concentration and coolant Reynolds number and decreasing the coolant inlet temperature.

scholarly journals Conjugate heat transfer performance of stepped lid-driven cavity with Al2O3/water nanofluid under forced and mixed convection

2021 ◽  
Vol 3 (6) ◽  
Author(s):  
Naveen Janjanam ◽  
Rajesh Nimmagadda ◽  
Lazarus Godson Asirvatham ◽  
R. Harish ◽  
Somchai Wongwises
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Mixed Convection ◽  
Conjugate Heat Transfer ◽  
Heat Transfer Performance ◽  
Pure Water ◽  
Interface Temperature ◽  
Transfer Model ◽  
Transfer Performance ◽  
Driven Cavity

AbstractTwo-dimensional conjugate heat transfer performance of stepped lid-driven cavity was numerically investigated in the present study under forced and mixed convection in laminar regime. Pure water and Aluminium oxide (Al2O3)/water nanofluid with three different nanoparticle volume concentrations were considered. All the numerical simulations were performed in ANSYS FLUENT using homogeneous heat transfer model for Reynolds number, Re = 100 to 500 and Grashof number, Gr = 5000, 13,000 and 20,000. Effective thermal conductivity of the Al2O3/water nanofluid was evaluated by considering the Brownian motion of nanoparticles which results in 20.56% higher value for 3 vol.% Al2O3/water nanofluid in comparison with the lowest thermal conductivity value obtained in the present study. A solid region made up of silicon is present underneath the fluid region of the cavity in three geometrical configurations (forward step, backward step and no step) which results in conjugate heat transfer. For higher Re values (Re = 500), no much difference in the average Nusselt number (Nuavg) is observed between forced and mixed convection. Whereas, for Re = 100 and Gr = 20,000, Nuavg value of mixed convection is 24% higher than that of forced convection. Out of all the three configurations, at Re = 100, forward step with mixed convection results in higher heat transfer performance as the obtained interface temperature is lower than all other cases. Moreover, at Re = 500, 3 vol.% Al2O3/water nanofluid enhances the heat transfer performance by 23.63% in comparison with pure water for mixed convection with Gr = 20,000 in forward step.

EXPERIMENTAL STUDY ON THERMAL TRANSPORT PHENOMENON OF NANOFLUIDS AS WORKING FLUID IN HEAT EXCHANGER

2014 ◽  
Vol 22 (01) ◽  
pp. 1450005 ◽  
Author(s):  
SHUICHI TORII
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Performance ◽  
Pure Water ◽  
Horizontal Tube ◽  
Constant Heat Flux ◽  
Working Fluid ◽  
Transfer Performance ◽  
Nanoparticles Concentration ◽  
Transfer Behavior

This paper aims to study the convective heat transfer behavior of aqueous suspensions of nanoparticles flowing through a horizontal tube heated under constant heat flux condition. Consideration is given to the effects of particle concentration and Reynolds number on heat transfer enhancement and the possibility of nanofluids as the working fluid in various heat exchangers. It is found that (i) significant enhancement of heat transfer performance due to suspension of nanoparticles in the circular tube flow is observed in comparison with pure water as the working fluid, (ii) enhancement is intensified with an increase in the Reynolds number and the nanoparticles concentration, and (iii) substantial amplification of heat transfer performance is not attributed purely to the enhancement of thermal conductivity due to suspension of nanoparticles.

Heat Transfer Performance of Different Nanofluids Flows in a Helically Coiled Heat Exchanger

2013 ◽  
Vol 832 ◽  
pp. 160-165 ◽  
Author(s):  
Mohammad Alam Khairul ◽  
Rahman Saidur ◽  
Altab Hossain ◽  
Mohammad Abdul Alim ◽  
Islam Mohammed Mahbubul
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Friction Factor ◽  
Heat Exchangers ◽  
Heat Transfer Performance ◽  
Volume Concentration ◽  
Transfer Performance

Helically coiled heat exchangers are globally used in various industrial applications for their high heat transfer performance and compact size. Nanofluids can provide excellent thermal performance of this type of heat exchangers. In the present study, the effect of different nanofluids on the heat transfer performance in a helically coiled heat exchanger is examined. Four different types of nanofluids CuO/water, Al2O3/water, SiO2/water, and ZnO/water with volume fractions 1 vol.% to 4 vol.% was used throughout this analysis and volume flow rate was remained constant at 3 LPM. Results show that the heat transfer coefficient is high for higher particle volume concentration of CuO/water, Al2O3/water and ZnO/water nanofluids, while the values of the friction factor and pressure drop significantly increase with the increase of nanoparticle volume concentration. On the contrary, low heat transfer coefficient was found in higher concentration of SiO2/water nanofluids. The highest enhancement of heat transfer coefficient and lowest friction factor occurred for CuO/water nanofluids among the four nanofluids. However, highest friction factor and lowest heat transfer coefficient were found for SiO2/water nanofluids. The results reveal that, CuO/water nanofluids indicate significant heat transfer performance for helically coiled heat exchanger systems though this nanofluids exhibits higher pressure drop.

scholarly journals Numerical study of flow patterns and heat transfer in mini twisted oval tubes

2015 ◽  
Vol 26 (12) ◽  
pp. 1550140 ◽  
Author(s):  
Amin Ebrahimi ◽  
Ehsan Roohi
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Performance ◽  
Numerical Study ◽  
Critical Role ◽  
Reynolds Numbers ◽  
Flow Patterns ◽  
Working Fluid ◽  
Transfer Performance ◽  
Temperature Dependent ◽  
Overall Performance

Flow patterns and heat transfer inside mini twisted oval tubes (TOTs) heated by constant-temperature walls are numerically investigated. Different configurations of tubes are simulated using water as the working fluid with temperature-dependent thermo-physical properties at Reynolds numbers ranging between 500 and 1100. After validating the numerical method with the published correlations and available experimental results, the performance of TOTs is compared to a smooth circular tube. The overall performance of TOTs is evaluated by investigating the thermal-hydraulic performance and the results are analyzed in terms of the field synergy principle and entropy generation. Enhanced heat transfer performance for TOTs is observed at the expense of a higher pressure drop. Additionally, the secondary flow generated by the tube-wall twist is concluded to play a critical role in the augmentation of convective heat transfer, and consequently, better heat transfer performance. It is also observed that the improvement of synergy between velocity and temperature gradient and lower irreversibility cause heat transfer enhancement for TOTs.

Sign in / Sign up

Export Citation Format

Share Document