General Beam Cross-Section Analysis Using a 3D Finite Element Slice

2014 ◽  
Author(s):  
Philippe Couturier ◽  
Steen Krenk
Keyword(s):  
Finite Element ◽  
Cross Section ◽  
Cross Sections ◽  
Degrees Of Freedom ◽  
Finite Thickness ◽  
Single Layer ◽  
Element Discretization ◽  
Cubic Polynomial ◽  
Hermitian Interpolation ◽  
Section Analysis

A formulation for analysis of general cross-section properties has been developed. This formulation is based on the stress-strain states in the classic six equilibrium modes of a beam by considering a finite thickness slice modelled by a single layer of 3D finite elements. The displacement variation in the lengthwise direction is in the form of a cubic polynomial, which is here represented by Hermitian interpolation, whereby the degrees of freedom are concentrated on the front and back faces of the slice. The theory is illustrated by application to a simple cross-section for which an analytical solution is available. The paper also shows an application to wind turbine blade cross-sections and discusses the effect of the finite element discretization on the cross-section properties such as stiffness parameters and the location of the elastic and shear centers.

scholarly journals Consistent coupling of positions and rotations for embedding 1D Cosserat beams into 3D solid volumes

2021 ◽  
Author(s):  
Ivo Steinbrecher ◽  
Alexander Popp ◽  
Christoph Meier
Keyword(s):  
Finite Element ◽  
Cross Section ◽  
Lagrange Multiplier ◽  
Degrees Of Freedom ◽  
Element Discretization ◽  
Geometrically Exact Beam ◽  
Coupling Constraints ◽  
Rotational Degrees Of Freedom ◽  
3D Solid ◽  
Cosserat Continua

AbstractThe present article proposes a mortar-type finite element formulation for consistently embedding curved, slender beams into 3D solid volumes. Following the fundamental kinematic assumption of undeformable cross-section s, the beams are identified as 1D Cosserat continua with pointwise six (translational and rotational) degrees of freedom describing the cross-section (centroid) position and orientation. A consistent 1D-3D coupling scheme for this problem type is proposed, requiring to enforce both positional and rotational constraints. Since Boltzmann continua exhibit no inherent rotational degrees of freedom, suitable definitions of orthonormal triads are investigated that are representative for the orientation of material directions within the 3D solid. While the rotation tensor defined by the polar decomposition of the deformation gradient appears as a natural choice and will even be demonstrated to represent these material directions in a $$L_2$$ L 2 -optimal manner, several alternative triad definitions are investigated. Such alternatives potentially allow for a more efficient numerical evaluation. Moreover, objective (i.e. frame-invariant) rotational coupling constraints between beam and solid orientations are formulated and enforced in a variationally consistent manner based on either a penalty potential or a Lagrange multiplier potential. Eventually, finite element discretization of the solid domain, the embedded beams, which are modeled on basis of the geometrically exact beam theory, and the Lagrange multiplier field associated with the coupling constraints results in an embedded mortar-type formulation for rotational and translational constraint enforcement denoted as full beam-to-solid volume coupling (BTS-FULL) scheme. Based on elementary numerical test cases, it is demonstrated that a consistent spatial convergence behavior can be achieved and potential locking effects can be avoided, if the proposed BTS-FULL scheme is combined with a suitable solid triad definition. Eventually, real-life engineering applications are considered to illustrate the importance of consistently coupling both translational and rotational degrees of freedom as well as the upscaling potential of the proposed formulation. This allows the investigation of complex mechanical systems such as fiber-reinforced composite materials, containing a large number of curved, slender fibers with arbitrary orientation embedded in a matrix material.

A Finite Element Model for Cables With Nonsymmetrical Geometry and Loads

1994 ◽  
Vol 116 (1) ◽  
pp. 14-20 ◽  
Author(s):  
T. T. Le ◽  
R. H. Knapp
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Cross Section ◽  
Cross Sections ◽  
Degrees Of Freedom ◽  
Circular Cross Section ◽  
Element Model ◽  
Computer Code ◽  
Deformation Analysis ◽  
Contact Points

A new two-dimensional finite element model is proposed for the deformation analysis of cable cross sections. The deformations of the cable cross section are of considerable design interest because of their effect on the induced torque or rotation of the cable. This model accounts for material orthotropy and nonsymmetrical geometry and loads. Each component of the cable is assumed to possess a circular cross section and is modeled as a macro-element having nodal degrees-of-freedom at all contact points with adjoining components. Usual finite element procedures are applied to solve for the unknown displacements at contact nodal points. The model is implemented in a computer code and is verified by test results obtained for an as-built cable.

Cross Section Analysis of Cu Filled TSVs Based on High Throughput Plasma-FIB Milling

2012 ◽  
Author(s):  
Frank Altmann ◽  
Jens Beyersdorfer ◽  
Jan Schischka ◽  
Michael Krause ◽  
German Franz ◽  
...  
Keyword(s):  
High Resolution ◽  
Cross Section ◽  
High Throughput ◽  
Cross Sections ◽  
Electron Backscatter Diffraction ◽  
Grain Structure ◽  
Electron Backscatter ◽  
Section Surface ◽  
Backscatter Diffraction ◽  
Section Analysis

Abstract In this paper the new Vion™ Plasma-FIB system, developed by FEI, is evaluated for cross sectioning of Cu filled Through Silicon Via (TSV) interconnects. The aim of the study presented in this paper is to evaluate and optimise different Plasma-FIB (P-FIB) milling strategies in terms of performance and cross section surface quality. The sufficient preservation of microstructures within cross sections is crucial for subsequent Electron Backscatter Diffraction (EBSD) grain structure analyses and a high resolution interface characterisation by TEM.

Stress concentration factors for the torsion of curved beams of arbitrary cross-section

2006 ◽  
Vol 220 (12) ◽  
pp. 1709-1726 ◽  
Author(s):  
R E Cornwell
Keyword(s):  
Finite Element ◽  
Stress Concentration ◽  
Cross Section ◽  
Cross Sections ◽  
Shear Stresses ◽  
Curved Beams ◽  
Finite Element Implementation ◽  
Out Of Plane ◽  
Concentration Factors ◽  
Stress Concentration Factors

There are numerous situations in machine component design in which curved beams with cross-sections of arbitrary geometry are loaded in the plane of curvature, i.e. in flexure. However, there is little guidance in the technical literature concerning how the shear stresses resulting from out-of-plane loading of these same components are effected by the component's curvature. The current literature on out-of-plane loading of curved members relates almost exclusively to the circular and rectangular cross-sections used in springs. This article extends the range of applicability of stress concentration factors for curved beams with circular and rectangular cross-sections and greatly expands the types of cross-sections for which stress concentration factors are available. Wahl's stress concentration factor for circular cross-sections, usually assumed only valid for spring indices above 3.0, is shown to be applicable for spring indices as low as 1.2. The theory applicable to the torsion of curved beams and its finite-element implementation are outlined. Results developed using the finite-element implementation agree with previously available data for circular and rectangular cross-sections while providing stress concentration factors for a wider variety of cross-section geometries and spring indices.

scholarly journals The Cross Section for the J = 0 → 2 Rotational Excitation of Hydrogen by Slow Electrons

1969 ◽  
Vol 22 (6) ◽  
pp. 715 ◽  
Author(s):  
RW Crompton ◽  
DK Gibson ◽  
AI McIntosh
Keyword(s):  
Momentum Transfer ◽  
Cross Section ◽  
Cross Sections ◽  
Vibrational Excitation ◽  
The Cross ◽  
Excitation Processes ◽  
Slow Electrons ◽  
And Diffusion ◽  
Momentum Transfer Cross Section ◽  
Section Analysis

The results of electron drift and diffusion measurements in parahydrogen have been analysed to determine the cross sections for momentum transfer and for rotational and vibrational excitation. The limited number of possible excitation processes in parahydrogen and the wide separation of the thresholds for these processes make it possible to determine uniquely the J = 0 → 2 rotational cross section from threshold to 0.3 eV. In addition, the momentum transfer cross section has been determined for energies less than 2 eV and it is shown that, near threshold, a vibrational cross section compatible with the data must lie within relatively narrow limits. The problems of uniqueness and accuracy inherent in the swarm method of cross section analysis are discussed. The present results are compared with other recent theoretical and experimental determinations; the agreement with the most recent calculations of Henry and Lane is excellent.

scholarly journals Membrane analogy for multi-material bars under torsion

2019 ◽  
Vol 475 (2225) ◽  
pp. 20190124 ◽  
Author(s):  
Laura Galuppi ◽  
Gianni Royer-Carfagni
Keyword(s):  
Finite Element ◽  
Cross Section ◽  
Cross Sections ◽  
Three Dimensional ◽  
Element Model ◽  
Elastic Problem ◽  
Two Dimensional ◽  
Torsion Problem ◽  
Linear Elastic ◽  
Physical Apparatus

Prandtl's membrane analogy for the torsion problem of prismatic homogeneous bars is extended to multi-material cross sections. The linear elastic problem is governed by the same equations describing the deformation of an inflated membrane, differently tensioned in regions that correspond to the domains hosting different materials in the bar cross section, in a way proportional to the inverse of the material shear modulus. Multi-connected cross sections correspond to materials with vanishing stiffness inside the holes, implying infinite tension in the corresponding portions of the membrane. To define the interface constrains that allow to apply such a state of prestress to the membrane, a physical apparatus is proposed, which can be numerically modelled with a two-dimensional mesh implementable in commercial finite-element model codes. This approach presents noteworthy advantages with respect to the three-dimensional modelling of the twisted bar.

Cross-Section Analysis in the Study of Windflow over Mountainous Terrain

1961 ◽  
Vol 42 (10) ◽  
pp. 693-702 ◽  
Author(s):  
Owen P. Cramer ◽  
Robert E. Lynott
Keyword(s):  
Cross Section ◽  
Cross Sections ◽  
Potential Temperature ◽  
Mountainous Terrain ◽  
Coast Range ◽  
Mountain Areas ◽  
Oregon Coast Range ◽  
Oregon Coast ◽  
Wind Structure ◽  
Section Analysis

The application of atmospheric cross sections to a relatively small area is explored as a tool in the study of surface winds in mountainous terrain. Covering a distance of only 50 mi through the Oregon Coast Range, these charts help in tracing airflow over local obstacles and portray changes in stability and stratification. Evidence is presented that vertical patterns of potential temperature must be considered in the detailed analysis of wind structure in mountain areas.

Development of a Nonlinear, C1-Beam Finite-Element Code for Actuator Design of Slender Flexible Robots

2017 ◽  
Author(s):  
Hidenori Murakami ◽  
Oscar Rios ◽  
Takeyuki Ono
Keyword(s):  
Finite Element ◽  
Large Deformation ◽  
Cross Section ◽  
Beam Model ◽  
Finite Element Code ◽  
Shape Functions ◽  
Lagrange Equations ◽  
Element Discretization ◽  
Flexible Robots ◽  
Actuator Design

For actuator design and motion simulations of slender flexible robots, planar C1-beam elements are developed for Reissner’s large deformation, shear-deformable, curbed-beam model. Internal actuation is mechanically modeled by a rate-form of beam constitutive relation, where actuation curvature is prescribed at each time. Geometrically, a curbed beam is modeled as a frame bundle, whereby at each point on beam’s curve of centroids a moving orthonormal frame is attached to a cross section. After a finite element discretization, a curve of centroids is modeled as a C1-curve, employing cubic shape functions for both planar coordinates with an arc-parameter. The cubic shape functions have already been utilized in linear Euler-Bernoulli beams for the interpolation of transverse displacement. To define the rotation angle of each cross section or the attitude of the moving frame, quadratic shape functions are used introducing a middle node, resulting in three angular nodal displacements. As a result, each beam element has total eleven nodal coordinates. The implementation of a nonlinear finite element code is facilitated by the principle of virtual work, which yields Reissner’s large deformation curbed beam model as the Euler-Lagrange equations. For time integration, the Newmark method is utilized. Finally, as applications of the code, a few inchworm motions induced by different actuation curvature fields are presented.

Support-Condition Analyses of Rotating Beams Under Distributed Imbalance Loading

2011 ◽  
Author(s):  
Kai Jokinen ◽  
Erno Keskinen ◽  
Marko Jorkama ◽  
Wolfgang Seemann
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Cross Section ◽  
Cross Sections ◽  
Natural Frequencies ◽  
Element Model ◽  
Mode Shapes ◽  
Constant Cross Section ◽  
Support Condition ◽  
Beam Elements

In roll balancing the behaviour of the roll can be studied either experimentally with trial weights or, if the roll dimensions are known, analytically by forming a model of the roll to solve response to imbalance. Essential focus in roll balancing is to find the correct amount and placing for the balancing mass or masses. If this selection is done analytically the roll model used in calculations has significant effect to the balancing result. In this paper three different analytic methods are compared. In first method the mode shapes of the roll are defined piece wisely. The roll is divided in to five parts having different cross sections, two shafts, two roll ends and a shell tube of the roll. Two boundary conditions are found for both supports of the roll and four combining equations are written to the interfaces of different roll parts. Totally 20 equations are established to solve the natural frequencies and to form the mode shapes of the non-uniform roll. In second model the flexibility of shafts and the stiffness of the roll ends are added to the support stiffness as serial springs and the roll is modelled as a one flexibly supported beam having constant cross section. Finally the responses to imbalance of previous models are compared to finite element model using beam elements. Benefits and limitations of each three model are then discussed.

Residual stress distribution in built-in beams

2020 ◽  
pp. 146442072095861
Author(s):  
FA de Castro ◽  
Paulo P Kenedi ◽  
LL Vignoli ◽  
I I T Riagusoff
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Stress Distribution ◽  
Cross Section ◽  
Cross Sections ◽  
Element Model ◽  
Residual Stress Distribution ◽  
Concentrated Load ◽  
Load Growth ◽  
Final Failure

Metallic hyperstatic structures, like beams, submitted to excessive loads, do not fail completely before fully yielding in more than one cross section. Indeed, for built-in beams, three cross sections must be fully yielded before the final failure can occur. So, modeling the evolution of the cross-section residual stress distribution is an important subject that should be addressed to guarantee the stress analysis modeling correctness. This paper analyses the residual stress distribution evolution, in critical cross sections, of built-in beams during a transversal concentrated load growth, until the final failure through hinges formation. A finite element model is also presented. The results show good matches with the numerical model, used as a reference.

Sign in / Sign up

Export Citation Format

Share Document