A Parametric Study of Air-Pumping Phenomenon in Tire Grooves Using Computational Fluid Dynamics

2016 ◽  
Author(s):  
Prashanta Gautam ◽  
Yousof Azizi ◽  
Abhilash J. Chandy
Keyword(s):  
Computational Model ◽  
Turbulence Modeling ◽  
Stokes Equations ◽  
Near Field ◽  
Hybrid Approach ◽  
Operating Conditions ◽  
Navier Stokes ◽  
Analytical Prediction ◽  
Tire Noise ◽  
Tire Rotation

The tire/road interaction process results in generation of noise, which is transmitted and audible in the inside and outside of the car. In the recent years, the structural-borne noise in a tire has been extensively studied. However, very few studies have been conducted on air-borne noise. Various studies and indoor experimental measurements suggest that among all air-borne tire noise mechanisms, air-pumping mechanisms, i.e. rapid displacement of air near the tire/road contact patch, is the dominant source of noise for certain tires and operating conditions. This research focuses on studying air-pumping mechanisms and uses a previously developed computational model to predict air-borne noise generated using a hybrid approach. The basis of the hybrid approach is a direct prediction of near-field solution using compressible Navier-Stokes equations with turbulence modeling, combined with an analytical prediction of far-field acoustics using an acoustic model. Only the near-field acoustic characteristics are discussed in this paper. The tire rotation and groove deformations at the tire/road contact is modeled through mesh motion and prescribed deformation functions, thereby circumventing the need for coupling with a structural solver for fluid-structure interactions. The capability of the developed computational model in estimating the tire noise is shown and the effects of varying different parameters such as tire speed and geometry on the evolution of the estimated responses at various near-field receiver locations are studied.

Computational Analysis of Tonal Noise Generated High-Bypass Ratio Fan Stage

2005 ◽  
Author(s):  
Aleksey M. Sipatov ◽  
Michail V. Usanin ◽  
Valery G. Avgustinovich ◽  
Natalia O. Chuhlantseva
Keyword(s):  
Pressure Distribution ◽  
Acoustic Analysis ◽  
Stokes Equations ◽  
Near Field ◽  
Hybrid Approach ◽  
Leading Edge ◽  
Navier Stokes ◽  
Far Field ◽  
Unsteady Pressure ◽  
Acoustic Contribution

The paper shows the procedure of estimating different fan stage geometries from the point of the fan stage aerodynamic and acoustic efficiency by using CFX v.5.6 gas dynamics software. Two different fan stages were examined. The acoustic analysis was made based on unsteady pressure distribution along exit guide vanes. The unsteady pressure distribution was determined from 3-D calculations of rotor-stator interactions. An improved approach is suggested to estimate acoustic sources with the leading edge geometry considered. Three various grid models were analyzed to estimate the grid discretization influence on computational results. The hybrid approach was used to evaluate the acoustic contribution of fan stage rotor–stator interaction to a turbo-jet engine total noise level on first harmonic in a far field. This approach consists of three steps. The first step includes the solving of Navier-Stokes equations in fan stage, the second step includes the solving of linearized Euler’s equations (LEE) in a near field and, then, the third covers the calculation of Ffowcs Williams–Hawkings (FWH) integral in a far field. The first step marked the effect of strong attenuation of acoustics modes in the fan passage. The results of calculations in the far field were compared with experiment data.

A Computational Analysis of Flow Field in Twin-Track Subway Tunnel to Improve Air Quality

2013 ◽  
Vol 319 ◽  
pp. 599-604
Author(s):  
Makhsuda Juraeva ◽  
Kyung Jin Ryu ◽  
Sang Hyun Jeong ◽  
Dong Joo Song
Keyword(s):  
Air Quality ◽  
Computational Model ◽  
Stokes Equations ◽  
Ventilation System ◽  
Three Dimensional ◽  
Aerodynamic Characteristics ◽  
Navier Stokes ◽  
Subway Tunnel ◽  
Air Supply ◽  
And Performance

A computational model of existing Seoul subway tunnelwas analyzed in this research. The computational model was comprised of one natural ventilationshaft, two mechanical ventilationshafts, one mechanical airsupply, a twin-track tunnel, and a train. Understanding the flow pattern of the train-induced airflow in the tunnel was necessary to improve ventilation performance. The research objective wasto improve the air quality in the tunnel by investigating train-induced airflow in the twin-track subway tunnel numerically. The numerical analysis characterized the aerodynamic behavior and performance of the ventilation system by solving three-dimensional turbulent Reynolds-averaged Navier-Stokes equations. ANSYS CFX software was used for the computations. The ventilation and aerodynamic characteristics in the tunnel were investigated by analyzing the mass flowrateat the exits of the ventilation mechanicalshafts. As the train passed the mechanical ventilation shafts, the amount of discharged-air in the ventilationshafts decreased rapidly. The air at the exits of the ventilation shafts was gradually recovered with time, after the train passed the ventilation shafts. The developed mechanical air-supply for discharging dusty air and supplying clean airwas investigated.The computational results showed that the developed mechanical air-supplycould improve the air quality in the tunnel.

ANALYSIS OF A HETEROGENEOUS DOMAIN DECOMPOSITION FOR COMPRESSIBLE VISCOUS FLOW

2001 ◽  
Vol 11 (04) ◽  
pp. 565-599 ◽  
Author(s):  
CRISTIAN A. COCLICI ◽  
WOLFGANG L. WENDLAND
Keyword(s):  
Domain Decomposition ◽  
Stokes Equations ◽  
Domain Decomposition Method ◽  
Near Field ◽  
Outer Region ◽  
Navier Stokes ◽  
Far Field ◽  
Computational Domain ◽  
Linearized Euler Equations ◽  
Naca0012 Airfoil

We analyze a nonoverlapping domain decomposition method for the treatment of two-dimensional compressible viscous flows around airfoils. Since at some distance to the given profile the inertial forces are strongly dominant, there the viscosity effects are neglected and the flow is assumed to be inviscid. Accordingly, we consider a decomposition of the original flow field into a bounded computational domain (near field) and a complementary outer region (far field). The compressible Navier–Stokes equations are used close to the profile and are coupled with the linearized Euler equations in the far field by appropriate transmission conditions, according to the physical properties and the mathematical type of the corresponding partial differential equations. We present some results of flow around the NACA0012 airfoil and develop an a posteriori analysis of the approximate solution, showing that conservation of mass, momentum and energy are asymptotically attained with the linear model in the far field.

scholarly journals Development of Hybrid Airlift-Jet Pump with Its Performance Analysis

2018 ◽  
Vol 8 (9) ◽  
pp. 1413 ◽  
Author(s):  
Dan Yao ◽  
Kwongi Lee ◽  
Minho Ha ◽  
Cheolung Cheong ◽  
Inhiug Lee
Keyword(s):  
Boundary Conditions ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Stokes Equations ◽  
Flow Characteristics ◽  
Operating Conditions ◽  
Navier Stokes ◽  
Jet Pump ◽  
Two Phase

A new pump, called the hybrid airlift-jet pump, is developed by reinforcing the advantages and minimizing the demerits of airlift and jet pumps. First, a basic design of the hybrid airlift-jet pump is schematically presented. Subsequently, its performance characteristics are numerically investigated by varying the operating conditions of the airlift and jet parts in the hybrid pump. The compressible unsteady Reynolds-averaged Navier-Stokes equations, combined with the homogeneous mixture model for multiphase flow, are used as the governing equations for the two-phase flow in the hybrid pump. The pressure-based methods combined with the Pressure-Implicit with Splitting of Operators (PISO) algorithm are used as the computational fluid dynamics techniques. The validity of the present numerical methods is confirmed by comparing the predicted mass flow rate with the measured ones. In total, 18 simulation cases that are designed to represent the various operating conditions of the hybrid pump are investigated: eight of these cases belong to the operating conditions of only the jet part with different air and water inlet boundary conditions, and the remaining ten cases belong to the operating conditions of both the airlift and jet parts with different air and water inlet boundary conditions. The mass flow rate and the efficiency are compared for each case. For further investigation into the detailed flow characteristics, the pressure and velocity distributions of the mixture in a primary pipe are compared. Furthermore, a periodic fluctuation of the water flow in the mass flow rate is found and analyzed. Our results show that the performance of the jet or airlift pump can be enhanced by combining the operating principles of two pumps into the hybrid airlift-jet pump, newly proposed in the present study.

scholarly journals Optimal design of nose and tail of an autonomous underwater vehicle hull to reduce drag force using numerical simulation

2019 ◽  
Vol 234 (1) ◽  
pp. 76-88 ◽  
Author(s):  
Mohammad Saghafi ◽  
Roham Lavimi
Keyword(s):  
Energy Consumption ◽  
Drag Force ◽  
Autonomous Underwater Vehicle ◽  
Turbulence Modeling ◽  
Stokes Equations ◽  
Autonomous Underwater Vehicles ◽  
Three Dimensional ◽  
Underwater Vehicle ◽  
Underwater Vehicles ◽  
Navier Stokes

In this research, the flow around the autonomous underwater vehicles with symmetrical bodies is numerically investigated. Increasing the drag force in autonomous underwater vehicles increases the energy consumption and decreases the duration of underwater exploration and operations. Therefore, the main objective of this research is to decrease drag force with the change in geometry to reduce energy consumption. In this study, the decreasing or increasing trends of the drag force of axisymmetric bare hulls have been studied by making alterations in the curve equations and creating the optimal geometric shapes in terms of hydrodynamics for the noses and tails of autonomous underwater vehicles. The incompressible, three-dimensional, and steady Navier–Stokes equations have been used to simulate the flow. Also, k-ε Realizable with enhanced wall treatment was used for turbulence modeling. Validation results were acceptable with respect to the 3.6% and 1.4% difference with numerical and experimental results. The results showed that all the autonomous underwater vehicle hulls designed in this study, at an attack angle of 0°, had a lower drag force than the autonomous underwater vehicle hull used for validation except geometry no. 1. In addition, nose no. 3 has been selected as the best nose according to the lowest value of stagnation pressure, and also tail no. 3 has been chosen as the best tail due to the production of the lowest vortex. Therefore, geometry no. 5 has been designed using nose and tail no. 3. The comparison made here showed that the maximum drag reduction in geometry no. 5 was equal to 26%, and therefore, it has been selected as the best bare hull in terms of hydrodynamics.

scholarly journals Modeling the 3-d flow around a cylinder using the SAS hybrid model

2014 ◽  
Vol 16 (5) ◽  
pp. 901-918 ◽  
Keyword(s):  
Turbulence Modeling ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Cross Flow ◽  
Numerical Code ◽  
Navier Stokes ◽  
Computational Domain ◽  
Mean Flow ◽  
Unstable Flow ◽  
Vortex Size

<div> <p>Three-dimensional calculations were performed to simulate the flow around a cylindrical vegetation element using the Scale Adaptive Simulation (SAS) model; commonly, this is the first step of the modeling of the flow through multiple vegetation elements. SAS solves the Reynolds Averaged Navier-Stokes equations in stable flow regions, while in regions with unstable flow it goes unsteady producing a resolved turbulent spectrum after reducing eddy viscosity according to the locally resolved vortex size represented by the von Karman length scale. A finite volume numerical code was used for the spatial discretisation of the rectangular computational domain with stream-wise, cross-flow and vertical dimensions equal to 30D, 11D and 1D, respectively, which was resolved with unstructured grids. Calculations were compared with experiments and Large Eddy Simulations (LES). Predicted overall flow parameters and mean flow velocities exhibited a very satisfactory agreement with experiments and LES, while the agreement of predicted turbulent stresses was satisfactory. Calculations showed that SAS is an efficient and relatively fast turbulence modeling approach, especially in relevant practical problems, in which the very high accuracy that can be achieved by LES at the expense of large computational times is not required.</p> </div> <p>&nbsp;</p>

Use of Experimental Data for an Efficient Description of Turbulent Flows

1990 ◽  
Vol 43 (5S) ◽  
pp. S240-S245 ◽  
Author(s):  
N. Aubry
Keyword(s):  
Experimental Data ◽  
Turbulent Flows ◽  
Turbulence Modeling ◽  
Stokes Equations ◽  
Original System ◽  
Navier Stokes ◽  
Lorenz Attractor ◽  
Wall Region ◽  
Lorenz Equations ◽  
Chaotic Solution

The proper orthogonal decomposition (POD), also called Karhunen-Loe`ve expansion, which extracts ‘coherent structures’ from experimental data, is a very efficient tool for analyzing and modeling turbulent flows. It has been shown that it converges faster than any other expansion in terms of kinetic energy (Lumley 1970). First, the POD is applied to the chaotic solution of the Lorenz equations. The dynamics of the Lorenz attractor is reconstructed by only the first three POD modes. In the second part of this paper, we show how the POD can be used in turbulence modeling. The particular case studied is the wall region of a turbulent boundary layer. In this flow, the velocity field is expanded into POD modes in the normal direction and Fourier modes in the streamwise and spanwise directions. Dynamical systems are obtained by Galerkin projections of the Navier Stokes equations onto the different modes. Aubry et al. (1988) applied the technique to derive and study a ten dimensional representation which reproduced qualitatively the bursting event experimentally observed. It is shown that streamwise modes, absent in Aubry et al.’s model, participate to the bursting events. This agrees remarkably well with experimental observations. In both examples, the dynamics of the original system is very well recovered from the contribution of only a few modes.

Assessing the Dynamic Stability of an Offshore Supply Vessel

2011 ◽  
Author(s):  
Vladimir Shigunov ◽  
Ould el Moctar ◽  
Thomas E. Schellin ◽  
Jan Kaufmann ◽  
Rasmus Stute
Keyword(s):  
Dynamic Stability ◽  
Stokes Equations ◽  
Operating Conditions ◽  
Navier Stokes ◽  
Ship Motions ◽  
Navier Stokes Equations ◽  
Counter Measures ◽  
Seakeeping Analysis ◽  
Design Speed ◽  
Run Up

The dynamic stability was investigated of a typical offshore service vessel operating under stability critical operating conditions. Excessive roll motions and relative motions at the stern were studied for two loading conditions for ship speeds ranging from zero to the design speed. A linear frequency-domain seakeeping analysis was followed by nonlinear time-domain simulations of ship motions in waves. Based on results from these methods, critical scenarios were selected and simulated using finite-volume solvers of the Reynolds-averaged Navier-Stokes equations to understand the phenomena related to dynamically unstable ship motions as well as to confirm the results of the simpler analysis methods. Results revealed the possibility of excessive roll motions and water run-up on deck; counter measures such as a ship-specific operational guidance are discussed.

Three-Dimensional Flowfields Inside a Transonic Compressor With Swept Blades

1991 ◽  
Vol 113 (2) ◽  
pp. 241-250 ◽  
Author(s):  
C. Hah ◽  
A. J. Wennerstrom
Keyword(s):  
Turbulence Modeling ◽  
Three Dimensional ◽  
Secondary Flows ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Navier Stokes ◽  
Navier Stokes Equation ◽  
Tip Clearance Flow ◽  
Transonic Compressor ◽  
Improved Performance

The concept of swept blades for a transonic or supersonic compressor was reconsidered by Wennerstrom in the early 1980s. Several transonic rotors designed with swept blades have shown very good aerodynamic efficiency. The improved performance of the rotor is believed to be due to reduced shock strength near the shroud and better distribution of secondary flows. A three-dimensional flowfield inside a transonic rotor with swept blades is analyzed in detail experimentally and numerically. A Reynolds-averaged Navier–Stokes equation is solved for the flow inside the rotor. The numerical solution is based on a high-order upwinding relaxation scheme, and a two-equation turbulence model with a low Reynolds number modification is used for the turbulence modeling. To predict flows near the shroud properly, the tip-clearance flow also must be properly calculated. The numerical results at three different operating conditions agree well with the available experimental data and reveal various interesting aspects of shock structure inside the rotor.

Sign in / Sign up

Export Citation Format

Share Document