Using Adsorption Cooling and Thermal Solar Collection for Residential Cooling Applications in Canada

2018 ◽  
Author(s):  
Jordan McNally ◽  
Christopher Baldwin ◽  
Cynthia A. Cruickshank
Keyword(s):  
Water Temperature ◽  
Flat Plate ◽  
Flow Rate ◽  
Heating System ◽  
Cooling Capacity ◽  
Hot Water ◽  
Inlet Temperature ◽  
Solar Collectors ◽  
Adsorption Chiller ◽  
The Difference

An adsorption chiller is a type of chiller that uses heat input as the driving force for chemical compression of a refrigerant and provides cooling with low electrical consumption. An experimental setup was designed, instrumented, and constructed to meet constant inlet temperature and flow rate requirements for the commercially available adsorption chiller unit tested. Two types of tests were conducted, one with a constant hot water temperature which represents a district style heating system and another with a varying hot water temperature, representing a system using flat plate solar collectors. Numerous tests were run with constant inlet temperatures across the complete operating range of the chiller and at varying flow rates for each of the three main inputs. It was determined that variations in temperature had a much more significant impact on the performance of the chiller, compared to the variations in flow rate, which were almost negligible within tested range. Dynamic inlet temperature tests were run using the modified system which uses data from a weather file to simulate a system using flat plate solar collectors and vary the hot water inlet temperature to the system. The results showed that when the average hot water inlet temperature is lower than 60°C and higher than 75°C, the difference in performance between constant inlet temperature and dynamic inlet temperature tests was very small. However, the cooling capacity at 75°C was about 4 kWth greater than at 60°C. Majority of the test produced a thermal COP between 0.45 and 0.50. Therefore, based off the solar collector system’s capacity to maintain a suitable average hot water temperature, the cooling performance of the chiller can be deemed suitable for residential applications.

scholarly journals EXPERIMENTAL STUDY OF FLAT PLATE SOLAR COLLECTORS WITH VARIOUS FLOW RATE OF WATER

2017 ◽  
Vol 5 (10) ◽  
pp. 112-116
Author(s):  
Anupras Shukla ◽  
Pushpraj Singh
Keyword(s):  
Experimental Study ◽  
Flat Plate ◽  
Flow Rate ◽  
Hot Water ◽  
Circular Pipe ◽  
Solar Water Heater ◽  
Solar Collectors ◽  
Flexible Pipe ◽  
Water Heater ◽  
Solar Water

In this paper, we are studying about solar water heater. The solar water heater are consisting of several components such as circular pipe, flexible pipe, and metallic container for water and circulating pump. We are analyzed the outlet temperatures of hot water using of various flow rate (in liters/ Minutes).

An Investigation of a Residential Solar System Coupled to a Radiant Panel Ceiling

1988 ◽  
Vol 110 (3) ◽  
pp. 172-179 ◽  
Author(s):  
Z. Zhang ◽  
M. Pate ◽  
R. Nelson
Keyword(s):  
Heat Exchanger ◽  
Solar System ◽  
Flat Plate ◽  
Storage Tank ◽  
Heating System ◽  
Hot Water ◽  
Radiant Heating ◽  
Solar Collectors ◽  
Water Storage Tank ◽  
Radiant Panel

An experimental study of a solar-radiant heating system was performed at Iowa State University’s Energy Research House (ERH). The ERH was constructed with copper tubes embedded in the plaster ceilings, thus providing a unqiue radiant heating system. In addition, 24 water-glycol, flat-plate solar collectors were mounted on the south side of the residence. The present study uses the solar collectors to heat a storage tank via a submerged copper tube coil. Hot water from the storage tank is then circulated through a heat exchanger, which heats the water flowing through the radiant ceiling. This paper contains a description of the solar-radiant system and an interpretation of the data that were measured during a series of transient experiments. In addition, the performance of the flat-plate solar collectors and the water storage tank were evaluated. The characteristics of a solar-to-radiant heat exchanger were also investigated. The thermal behavior of the radiant ceiling and the room enclosures were observed, and the heat transfer from the ceiling by radiation and convection was estimated. The overall heating system was also evaluated using the thermal performances of the individual components. The results of this study verify that it is feasible to use a solar system coupled to a low-temperature radiant-panel heating system for space heating. A sample performance evaluation is also presented.

scholarly journals Performance Investigation of a Two-Bed Type Adsorption Chiller with Various Adsorbents

Energies ◽  
2020 ◽  
Vol 13 (10) ◽  
pp. 2553 ◽  
Author(s):  
Jung-Gil Lee ◽  
Kyung Jin Bae ◽  
Oh Kyung Kwon
Keyword(s):  
Performance Evaluation ◽  
Physical Properties ◽  
Water Temperature ◽  
Silica Gel ◽  
System Performance ◽  
Waste Heat ◽  
Sustainable Energy ◽  
Cooling Capacity ◽  
Hot Water ◽  
Adsorption Chiller

In this study, the performance evaluation of an adsorption chiller (AD) system with three different adsorbents—silica-gel, aluminum fumarate, and FAM-Z01—was conducted to investigate the effects of adsorption isotherms and physical properties on the system’s performance. In addition, the performance evaluation of the AD system for a low inlet hot-water temperature of 60 °C was performed to estimate the performance of the system when operated by low quality waste heat or sustainable energy sources. For the simulation work, a two-bed type AD system is considered, and silica-gel, metal organic frameworks (MOFs), and ferro-aluminophosphate (FAPO, FAM-Z01) were employed as adsorbents. The simulation results were well matched with the laboratory-scale experimental results and the maximum coefficient of performance (COP) difference was 7%. The cooling capacity and COP of the AD system were investigated at different operating conditions to discuss the influences of the adsorbents on the system performance. Through this study, the excellence of the adsorbent, which has an S-shaped isotherm graph, was presented. In addition, the influences of the physical properties of the adsorbent were also discussed with reference to the system performance. Among the three different adsorbents employed in the AD system, the FAM-Z01 shows the best performance at inlet hot water temperature of 60 °C, which can be obtained from waste heat or sustainable energy, where the cooling capacity and COP were 5.13 kW and 0.47, respectively.

scholarly journals Technical Analysis of Glazed and Unglazed Flat Plate Solar Collectors at Several Water Flow Rate and Inlet Temperature

2019 ◽  
Vol 07 (1) ◽  
pp. 113-120
Author(s):  
Rustam Efendi ◽  
◽  
Leopold Oscar Nelwan ◽  
Dyah Wulandani ◽  
◽  
...  
Keyword(s):  
Flat Plate ◽  
Water Flow ◽  
Flow Rate ◽  
Water Flow Rate ◽  
Technical Analysis ◽  
Inlet Temperature ◽  
Solar Collectors

scholarly journals Optimal design of compact organic Rankine cycle units for domestic solar applications

2014 ◽  
Vol 18 (3) ◽  
pp. 811-822 ◽  
Author(s):  
Luca Barbazza ◽  
Leonardo Pierobon ◽  
Alberto Mirandola ◽  
Fredrik Haglind
Keyword(s):  
Heat Exchanger ◽  
Water Temperature ◽  
Flat Plate ◽  
Thermal Efficiency ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Hot Water ◽  
Working Fluid ◽  
Solar Collectors ◽  
Allowable Temperature

Organic Rankine cycle turbogenerators are a promising technology to transform the solar radiation harvested by solar collectors into electric power. The present work aims at sizing a small-scale organic Rankine cycle unit by tailoring its design for domestic solar applications. Stringent design criteria, i. e., compactness, high performance and safe operation, are targeted by adopting a multi-objective optimization approach modeled with the genetic algorithm. Design-point thermodynamic variables, e. g., evaporating pressure, the working fluid, minimum allowable temperature differences, and the equipment geometry, are the decision variables. Flat plate heat exchangers with herringbone corrugations are selected as heat transfer equipment for the preheater, the evaporator and the condenser. The results unveil the hyperbolic trend binding the net power output to the heat exchanger compactness. Findings also suggest that the evaporator and condenser minimum allowable temperature differences have the largest impact on the system volume and on the cycle performances. Among the fluids considered, the results indicate that R1234yf and R1234ze are the best working fluid candidates. Using flat plate solar collectors (hot water temperature equal to 75 ?C), R1234yf is the optimal solution. The heat exchanger volume ranges between 6.0 and 23.0 dm3, whereas the thermal efficiency is around 4.5%. R1234ze is the best working fluid employing parabolic solar collectors (hot water temperature equal to 120 ?C). In such case the thermal efficiency is around 6.9%, and the heat exchanger volume varies from 6.0 to 18.0 dm3.

scholarly journals THE USE OF SOLAR ENERGY FOR PREPARING DOMESTIC HOT WATER IN A MULTI-STOREY BUILDING / SAULĖS ENERGIJOS PANAUDOJIMAS KARŠTAM VANDENIUI RUOŠTI DAUGIABUČIAME NAME

2012 ◽  
Vol 5 (4) ◽  
pp. 507-512 ◽  
Author(s):  
Giedrius Šiupšinskas ◽  
Solveiga Adomėnaitė
Keyword(s):  
Flat Plate ◽  
Water System ◽  
District Heating ◽  
Heating System ◽  
Hot Water ◽  
Solar Collectors ◽  
District Heating System ◽  
Climate Conditions ◽  
Domestic Hot Water ◽  
Life Project

The article analyses the possibilities of solar collectors used for a domestic hot water system and installed on the roofs of modernized multi-storey buildings under the existing climate conditions. A number of combinations of flat plate and vacuum solar collectors with accumulation tank systems of various sizes have been examined. Heat from the district heating system is used as an additional heat source for preparing domestic hot water. The paper compares calculation results of energy and economy regarding the combinations of flat plate and vacuum solar collectors and the size of the accumulation tank. The influence of variations in the main indicators on the final economic results has also been evaluated. Research has been supported applying EC FP7 CONCERTO program (‘‘Sustainable Zero Carbon ECO-Town Developments Improving Quality of Life across EU - ECO-Life’’ (ECO-Life Project) Contract No. TREN/FP7EN/239497/”ECOLIFE”). Santrauka Straipsnyje analizuojamos saulės kolektorių, skirtų karšto vandentiekio sistemai ant modernizuojamų daugiabučių namų stogų įrengti esamomis klimatinėmis sąlygomis galimybės. Nagrinėjamos įvairaus dydžio plokščiųjų ir vakuuminių saulės kolektorių su akumuliacinėmis talpyklomis sistemų kombinacijos. Kaip papildomas šilumos šaltinis karštam vandeniui pašildyti naudojama iš centralizuotų šilumos tinklų tiekiama šiluma. Lyginami plokščiųjų, vakuuminių saulės kolektorių ir akumuliacinio bako dydžio kombinacijų energinių ir ekonominių skaičiavimų rezultatai. Įvertinama kai kurių esminių rodiklių pokyčių įtaka galutiniams ekonominiams rodikliams.

scholarly journals Minimum Number of Experimental Data for the Thermal Characterization of a Hot Water Storage Tank

Energies ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4741
Author(s):  
María Gasque ◽  
Federico Ibáñez ◽  
Pablo González-Altozano
Keyword(s):  
Experimental Data ◽  
Water Temperature ◽  
Temperature Profile ◽  
Storage Tank ◽  
Water Storage ◽  
Hot Water ◽  
Experimental Temperature ◽  
Inlet Temperature ◽  
Water Storage Tank ◽  
Minimum Number

This paper demonstrates that it is possible to characterize the water temperature profile and its temporal trend in a hot water storage tank during the thermal charge process, using a minimum number of thermocouples (TC), with minor differences compared to experimental data. Four experimental tests (two types of inlet and two water flow rates) were conducted in a 950 L capacity tank. For each experimental test (with 12 TC), four models were developed using a decreasing number of TC (7, 4, 3 and 2, respectively). The results of the estimation of water temperature obtained with each of the four models were compared with those of a fifth model performed with 12 TC. All models were tested for constant inlet temperature. Very acceptable results were achieved (RMSE between 0.2065 °C and 0.8706 °C in models with 3 TC). The models were also useful to estimate the water temperature profile and the evolution of thermocline thickness even with only 3 TC (RMSE between 0.00247 °C and 0.00292 °C). A comparison with a CFD model was carried out to complete the study with very small differences between both approaches when applied to the estimation of the instantaneous temperature profile. The proposed methodology has proven to be very effective in estimating several of the temperature-based indices commonly employed to evaluate thermal stratification in water storage tanks, with only two or three experimental temperature data measurements. It can also be used as a complementary tool to other techniques such as the validation of numerical simulations or in cases where only a few experimental temperature values are available.

Experimental Investigation of a Pilot Compression Chiller With Alternatives Refrigerants R401a and R134a

2005 ◽  
Author(s):  
M. Fatouh
Keyword(s):  
Experimental Investigation ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Water Mass ◽  
Cooling Water ◽  
Cooling Capacity ◽  
Inlet Temperature ◽  
Chilled Water ◽  
Water Mass Flow Rate

This paper reports the results of an experimental investigation on a pilot compression chiller (4 kW cooling capacity) working with R401a and R134a as R12 alternatives. Experiments are conducted on a single-stage vapor compression refrigeration system using water as a secondary working fluid through both evaporator and condenser. Influences of cooling water mass flow rate (170–1900 kg/h), cooling water inlet temperature (27–43°C) and chilled water mass flow rate (240–1150 kg/h) on performance characteristics of chillers are evaluated for R401a, R134a and R12. Increasing cooling water mass flow rate or decreasing its inlet temperature causes the operating pressures and electric input power to reduce while the cooling capacity and coefficient of performance (COP) to increase. Pressure ratio is inversely proportional while actual loads and COP are directly proportional to chilled water mass flow rate. The effect of cooling water inlet temperature, on the system performance, is more significant than the effects of cooling and chilled water mass flow rates. Comparison between R12, R134a and R401a under identical operating conditions revealed that R401a can be used as a drop-in refrigerant to replace R12 in water-cooled chillers.

Evacuated Tube Heat Pipe Solar Collectors Applied to Recirculation Loop in a Federal Building: SSA Philadelphia

Solar Energy ◽  
2004 ◽  
Author(s):  
Andy Walker ◽  
Fariborz Mahjouri ◽  
Robert Stiteler
Keyword(s):  
Solar Energy ◽  
Heat Pipe ◽  
Heat Loss ◽  
Heating System ◽  
Hot Water ◽  
Solar Array ◽  
Solar Collectors ◽  
Water Heating ◽  
Evacuated Tube ◽  
Recirculation Loop

This paper describes design, simulation, construction and measured initial performance of a solar water heating system (360 Evacuated Heat-Pipe Collector tubes, 54 m2 gross area, 36 m2 net absorber area) installed at the top of the hot water recirculation loop in the Social Security Mid-Atlantic Center in Philadelphia. Water returning to the hot water storage tank is heated by the solar array when solar energy is available. This new approach, as opposed to the more conventional approach of preheating incoming water, is made possible by the thermal diode effect of heat pipes and low heat loss from evacuated tube solar collectors. The simplicity of this approach and its low installation costs makes the deployment of solar energy in existing commercial buildings more attractive, especially where the roof is far removed from the water heating system, which is often in the basement. Initial observed performance of the system is reported. Hourly simulation estimates annual energy delivery of 111 GJ/year of solar heat and that the annual efficiency (based on the 54 m2 gross area) of the solar collectors is 41%, and that of the entire system including parasitic pump power, heat loss due to freeze protection, and heat loss from connecting piping is 34%. Annual average collector efficiency based on a net aperture area of 36 m2 is 61.5% according to the hourly simulation.

scholarly journals An experimental study of the thermal performance of the square and rhombic solar collectors

2018 ◽  
Vol 22 (1 Part B) ◽  
pp. 487-494 ◽  
Author(s):  
Aminreza Noghrehabadi ◽  
Ebrahim Hajidavaloo ◽  
Mojtaba Moravej ◽  
Ali Esmailinasab
Keyword(s):  
Experimental Study ◽  
Flat Plate ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Thermal Performance ◽  
Thermal Efficiency ◽  
Solar Collectors ◽  
Heating Systems ◽  
Solar Water Heating

Solar collectors are the key part of solar water heating systems. The most widely produced solar collectors are flat plate solar collectors. In the present study, two types of flat plate collectors, namely square and rhombic collectors are experi?mentally tested and compared and the thermal performance of both collectors is investigated. The results show both collectors have the same performance around noon (?61%), but the rhombic collector has better performance in the morning and afternoon. The values for rhombic and square collectors are approximately 56.2% and 53.5% in the morning and 56.1% and 54% in the afternoon, respectively. The effect of flow rate is also studied. The thermal efficiency of rhombic and square flat plate collectors increases in proportion to the flow rate. The results indicated the rhombic collector had better performance in comparison with the square collector with respect to the mass-flow rate.

Sign in / Sign up

Export Citation Format

Share Document