Vibration Analysis of Cable-Driven Parallel Robot for Asymmetric Tension and Position

2016 ◽  
Author(s):  
Hyundong Do ◽  
Kyoung-Su Park
Keyword(s):  
Vibration Analysis ◽  
Parallel Manipulators ◽  
Parallel Robot ◽  
The Other ◽  
End Effector ◽  
Cable Robot

Cable-driven parallel robot (CDPR) consists of three parts: an end-effector, a number of cables and actuators. CDPRs are a type of parallel manipulators which the end-effector is supported in parallel by cables. CDPRs have two types. One is the fully-constrained type, and the other is the under constrained type. Fully-constrained type cable robot require n+1 wires, where n is the number of freedom to be constrained [1].

Experimental results for the flexible joint cable-suspended manipulator of ICaSbot

Robotica ◽  
2013 ◽  
Vol 31 (6) ◽  
pp. 887-904 ◽  
Author(s):  
M. H. Korayem ◽  
M. Bamdad ◽  
H. Tourajizadeh ◽  
A. H. Korayem ◽  
R. M. Zehtab ◽  
...  
Keyword(s):  
Degrees Of Freedom ◽  
Experimental Tests ◽  
Parallel Robot ◽  
Joint Space ◽  
End Effector ◽  
Flexible Joint ◽  
Cable Robot ◽  
Six Dof ◽  
And Control ◽  
Computed Torque

SUMMARYIn this paper, design, dynamic, and control of the motors of a spatial cable robot are presented considering flexibility of the joints. End-effector control in order to control all six spatial degrees of freedom (DOFs) of the system and motor control in order to control the joints flexibility are proposed here. Corresponding programing of its operation is done by formulating the kinematics and dynamics and also control of the robot. Considering the existence of gearboxes, flexibility of the joints is modeled in the feed-forward term of its controller to achieve better accuracy. A two sequential closed-loop strategy consisting of proportional derivative (PD) for linear actuators in joint space and computed torque method for nonlinear end-effector in Cartesian space is presented for further accuracy. Flexibility is estimated using modeling and simulation by MATLAB and SimDesigner. A prototype has been built and experimental tests have been done to verify the efficiency of the proposed modeling and controller as well as the effect of flexibility of the joints. The ICaSbot (IUST Cable-Suspended robot) is an under-constrained six-DOF parallel robot actuated by the aid of six suspended cables. An experimental test is conducted for the manufactured flexible joint cable robot of ICaSbot and the outputs of sensors are compared with simulation. The efficiency of the proposed schemes is demonstrated.

DeltaBot: A New Cable-Based Ultra High Speed Robot

2003 ◽  
Author(s):  
Saeed Behzadipour ◽  
Robert Dekker ◽  
Amir Khajepour ◽  
Edmon Chan
Keyword(s):  
High Speed ◽  
Degrees Of Freedom ◽  
Manufacturing Industry ◽  
Design Procedure ◽  
Parallel Manipulators ◽  
Parallel Robot ◽  
Parallel Robots ◽  
Manufacturing Cost ◽  
End Effector ◽  
Serial Manipulators

The growing needs for high speed positioning devices in the automated manufacturing industry have been challenged by robotic science for more than two decades. Parallel manipulators have been widely used for this purpose due to their advantage of lower moving inertia over the conventional serial manipulators. Cable actuated parallel robots were introduced in 1980’s to reduce the moving inertia even further. In this work, a new cable-based parallel robot is introduced. For this robot, the cables are used not only to actuate the end-effector but also to apply the necessary kinematic constraints to provide three pure translational degrees of freedom. In order to maintain tension in the cables, a passive air cylinder is used to push the end-effector against the stationary platform. In addition to low moving inertia, the new design benefits from simplicity and low manufacturing cost by eliminating joints from the robot’s mechanism. The design procedure and the results of experiments will be discussed in the following.

Kinematic and Kinetostatic Analysis of Parallel Manipulators with Emphasis on Position, Motion, and Actuation Singularities

Robotica ◽  
2018 ◽  
Vol 37 (4) ◽  
pp. 599-625 ◽  
Author(s):  
M. Kemal Ozgoren
Keyword(s):  
Inverse Kinematics ◽  
Parallel Manipulators ◽  
Singularity Analysis ◽  
The Other ◽  
Forward Kinematics ◽  
Velocity Mapping ◽  
Active Joint ◽  
End Effector ◽  
Jacobian Matrices ◽  
Other Hand

SummaryThis paper provides a contribution to the singularity analysis of the parallel manipulators by introducing the position singularities in addition to the motion and actuation singularities. The motion singularities are associated with the linear velocity mapping between the task and joint spaces. So, they are the singularities of the relevant Jacobian matrices. On the other hand, the position singularities are associated with the nonlinear position mapping between the task and joint spaces. So, they are encountered in the position-level solutions of the forward and inverse kinematics problems. In other words, they come out irrespective of the velocity mapping and the Jacobian matrices. Considering these distinctions, a kinematic singularity is denoted here by one of the four acronyms, which are PSFK (position singularity of forward kinematics), PSIK (position singularity of inverse kinematics), MSFK (motion singularity of forward kinematics), and MSIK (motion singularity of inverse kinematics). There may also occur an actuation singularity (ACTS) concerning the kinetostatic relationships that involve forces and moments. However, it is verified that an ACTS is the same as an MSFK. Each singularity induces different consequences in the joint and task spaces. A PSFK imposes a constraint on the active joint variables and makes the end-effector position indefinite and uncontrollable. Therefore, it must be avoided. An MSFK imposes a constraint on the rates of the active joint variables and makes the end-effector motion indefinite and easily perturbable. Besides, since it is also an ACTS, it causes the actuator torques or forces to grow without bound. Therefore, it must also be avoided. On the other hand, a PSIK imposes a constraint on the end-effector position but provides freedom for the active joint variables. Similarly, an MSIK imposes a constraint on the end-effector motion but provides freedom for the rates of the active joint variables. A PSIK or MSIK need not be avoided if the constraint it imposes on the position or motion of the end-effector is acceptable or if the task can be planned to be compatible with that constraint. Besides, with such a compatible task, a PSIK or MSIK may even be advantageous, because the freedom it provides for the active joint variables can sometimes be used for a secondary purpose. This paper is also concerned with the multiplicities of forward kinematics in the assembly modes of the manipulator and the multiplicities of inverse kinematics in the posture modes of the legs. It is shown that the assembly mode changing poses of the manipulator are the same as the MSFK poses, and the posture mode changing poses of the legs are the same as the MSIK poses.

Oscillation Reduction and Frequency Analysis of Under-Constrained Cable-Driven Parallel Robot with Three Cables

Robotica ◽  
2019 ◽  
Vol 38 (3) ◽  
pp. 375-395 ◽  
Author(s):  
Sung Wook Hwang ◽  
Jeong-Hyeon Bak ◽  
Jonghyun Yoon ◽  
Jong Hyeon Park
Keyword(s):  
Frequency Analysis ◽  
Degrees Of Freedom ◽  
Natural Frequencies ◽  
Vibration Suppression ◽  
Parallel Manipulators ◽  
Parallel Robot ◽  
Parallel Robots ◽  
Input Shaping ◽  
End Effector ◽  
Multi Mode

SummaryCable-driven parallel robots (CDPRs) possess a lot of advantages over conventional parallel manipulators and link-based robot manipulators in terms of acceleration due to their low inertia. This paper deals with under-constrained CDPRs, which manipulate the end-effector to carrying the payload by using a number of cables less than six, often used preferably owing to their simple structures. Since a smaller number of cables than six are used, the end-effector of CDPR has uncontrollable degrees of freedom and that causes swaying motion and oscillations. In this paper, a scheme to curb on the unwanted oscillation of the end-effector of the CDPR with three cables is proposed based on multimode input shaping. The precise dynamic model of the under-constrained CDPR is obtained to find natural frequencies, which depends on the position of the end-effector. The advantage of the proposed method is that it is practicable to generate the trajectories for vibration suppression based on multi-mode input-shaping scheme in spite of the complexity in the dynamics and the difficulty in computing the natural frequencies of the CDPR, which are required in any input-shaping scheme. To prove the effectiveness of the proposed method, computer simulations and experiments were carried out by using 3-D motion for CDPR with three cables.

Calibration of Hexaglide Parallel Manipulators Using Only Input Joint Variables

2008 ◽  
Author(s):  
Mansour Abtahi ◽  
Hodjat Pendar ◽  
Aria Alasty ◽  
Gholamreza Vossoughi
Keyword(s):  
Task Performance ◽  
Parallel Manipulators ◽  
Parallel Robot ◽  
Parallel Robots ◽  
Positioning Accuracy ◽  
Measuring Device ◽  
End Effector ◽  
System Calibration ◽  
On Line ◽  
Calibration Accuracy

In the application of parallel robots, it is necessary to calibrate the geometric parameters and improve the positioning accuracy for accurate task performance. Traditionally, to perform system calibration, one needs to measure a number of robot poses using an external measuring device. However, this process is often time-consuming, expensive and difficult for robot on-line calibration. In this paper, a methodical way of self-calibrating of Hexaglide parallel robot is introduced. This method is performable only by measuring input joint variables in some sets of configurations where in each set center of the end-effector is fixed, but orientations are different. Simulations give us an idea about the number of points that must be measured, the number of orientations in each point and the effect of noise on the calibration accuracy.

Static of Parallel Manipulators and Closeness to Singularity

2008 ◽  
Vol 1 (1) ◽  
Author(s):  
J. Hubert ◽  
J.-P. Merlet
Keyword(s):  
Static Analysis ◽  
Parallel Manipulators ◽  
Parallel Robot ◽  
Parallel Robots ◽  
Practical Issue ◽  
End Effector ◽  
Joint Forces ◽  
Fixed Threshold

Singularity is a major problem for parallel robots as in these configurations the robot cannot be controlled, and there may be infinite forces/torques in its joints, possibly leading to a robot breakdown. In the recent years classification and detection of singularities have made large progress. However, the issue of closeness to a singularity is still open and we propose in this paper an approach that is based on a static analysis. Our measure of closeness to a singularity is based on the very practical issue of having the joint forces/torques lower than a given threshold. We consider a planar parallel robot whose end-effector has a constant orientation and is submitted to a known wrench and we show that it is possible to compute the border of the region that describes all possible end-effector location for which the joint forces are lower than the fixed threshold.

Analysis and Optimization of a New Differentially Driven Cable Parallel Robot

2015 ◽  
Vol 7 (3) ◽  
Author(s):  
Hamed Khakpour ◽  
Lionel Birglen ◽  
Souheil-Antoine Tahan
Keyword(s):  
Kinematic Analysis ◽  
Design Methodology ◽  
Degrees Of Freedom ◽  
Parallel Robot ◽  
Cable Robot ◽  
Proper Design ◽  
Two Indices ◽  
Three Degrees Of Freedom ◽  
Cable Robots

In this paper, a new three degrees of freedom (DOF) differentially actuated cable parallel robot is proposed. This mechanism is driven by a prismatic actuator and three cable differentials. Through this design, the idea of using differentials in the structure of a spatial cable robot is investigated. Considering their particular properties, the kinematic analysis of the robot is presented. Then, two indices are defined to evaluate the workspaces of the robot. Using these indices, the robot is subsequently optimized. Finally, the performance of the optimized differentially driven robot is compared with fully actuated mechanisms. The results show that through a proper design methodology, the robot can have a larger workspace and better performance using differentials than the fully driven cable robots using the same number of actuators.

Kinematic analysis and design of a novel 6-degree of freedom parallel robot

2014 ◽  
Vol 229 (2) ◽  
pp. 291-303 ◽  
Author(s):  
DU Hui ◽  
GAO Feng ◽  
PAN Yang
Keyword(s):  
Set Theory ◽  
Kinematic Analysis ◽  
Parallel Mechanism ◽  
Design Methodology ◽  
Parallel Robot ◽  
End Effector ◽  
Analysis And Design ◽  
Velocity Models ◽  
Reachable Workspace ◽  
Rotational Motions

A novel 3-UP3R parallel mechanism with six degree of freedoms is proposed in this paper. One most important advantage of this mechanism is that the three translational and three rotational motions are partially decoupled: the end-effector position is only determined by three inputs, while the rotational angles are relative to all six inputs. The design methodology via GF set theory is brought out, using which the limb type can be determined. The mobility of the end-effector is analyzed. After that, the kinematic and velocity models are formulated. Then, workspace is studied, and since the robot is partially decoupled, the reachable workspace is also the dexterous workspace. In the end, both local and global performances are discussed using conditioning indexes. The experiment of real prototype shows that this mechanism works well and may be applied in many fields.

Three-Degree-of-Freedom Parallel Robot Arm

2006 ◽  
Author(s):  
Martin Hosek ◽  
Michael Valasek ◽  
Jairo Moura
Keyword(s):  
Parallel Robot ◽  
Degree Of Freedom ◽  
Motion Path ◽  
Angular Orientation ◽  
Robot Arm ◽  
Flat Panel Display ◽  
End Effector ◽  
Cluster Tools ◽  
Manufacturing Applications ◽  
Three Degree Of Freedom

This paper presents single- and dual-end-effector configurations of a planar three-degree of freedom parallel robot arm designed for automated pick-place operations in vacuum cluster tools for semiconductor and flat-panel-display manufacturing applications. The basic single end-effector configuration of the arm consists of a pivoting base platform, two elbow platforms and a wrist platform, which are connected through two symmetric pairs of parallelogram mechanisms. The wrist platform carries an end-effector, the position and angular orientation of which can be controlled independently by three motors located at the base of the robot. The joints and links of the mechanism are arranged in a unique geometric configuration which provides a sufficient range of motion for typical vacuum cluster tools. The geometric properties of the mechanism are further optimized for a given motion path of the robot. In addition to the basic symmetric single end-effector configuration, an asymmetric costeffective version of the mechanism is derived, and two dual-end-effector alternatives for improved throughput performance are described. In contrast to prior attempts to control angular orientation of the end-effector(s) of the conventional arms employed currently in vacuum cluster tools, all of the motors that drive the arm can be located at the stationary base of the robot with no need for joint actuators carried by the arm or complicated belt arrangements running through the arm. As a result, the motors do not contribute to the mass and inertia properties of the moving parts of the arm, no power and signal wires through the arm are necessary, the reliability and maintenance aspects of operation are improved, and the level of undesirable particle generation is reduced. This is particularly beneficial for high-throughput applications in vacuum and particlesensitive environments.

scholarly journals Proposal of a Decoupled Structure of Fuzzy-PID Controllers Applied to the Position Control in a Planar CDPR

Electronics ◽  
2021 ◽  
Vol 10 (6) ◽  
pp. 745
Author(s):  
Marco Carpio ◽  
Roque Saltaren ◽  
Julio Viola ◽  
Cristian Calderon ◽  
Juan Guerra
Keyword(s):  
Position Control ◽  
Control Structure ◽  
Parallel Robot ◽  
Pid Controllers ◽  
Fuzzy Pid ◽  
End Effector ◽  
Robot Systems ◽  
Decoupled Control ◽  
The Mathematical Model ◽  
Decoupled Structure

The design of robot systems controlled by cables can be relatively difficult when it is approached from the mathematical model of the mechanism, considering that its approach involves non-linearities associated with different components, such as cables and pulleys. In this work, a simple and practical decoupled control structure proposal that requires practically no mathematical analysis was developed for the position control of a planar cable-driven parallel robot (CDPR). This structure was implemented using non-linear fuzzy PID and classic PID controllers, allowing performance comparisons to be established. For the development of this research, first the structure of the control system was proposed, based on an analysis of the cables involved in the movement of the end-effector (EE) of the robot when they act independently for each axis. Then a tuning of rules was carried out for fuzzy PID controllers, and Ziegler–Nichols tuning was applied to classic PID controllers. Finally, simulations were performed in MATLAB with the Simulink and Simscape tools. The results obtained allowed us to observe the effectiveness of the proposed structure, with noticeably better performance obtained from the fuzzy PID controllers.

Sign in / Sign up

Export Citation Format

Share Document