Projection Micro-Stereolithography of Temperature Responsive Mechanically Tough Hydrogels

2016 ◽  
Author(s):  
Daehoon Han ◽  
Zhaocheng Lu ◽  
Howon Lee
Keyword(s):  
Mechanical Properties ◽  
Transition Temperature ◽  
High Resolution ◽  
Hybrid Networks ◽  
Micro Fabrication ◽  
Temperature Responsive ◽  
Degree Of Swelling ◽  
3D Printed ◽  
Reconfigurable Structures ◽  
Ionic Crosslinks

Temperature responsive hydrogel has attracted considerable attention as an outstanding material for creating a variety of reconfigurable structures. As a well-known temperature responsive hydrogel, poly(N-isopropylacrylamide) (PNIPAAm) has been widely used in various applications. Here, we report high resolution 3D micro fabrication of PNIPAAm structures using projection micro-stereolithography (PμSL). We also show the controllability of degree of swelling and transition temperature of 3D printed PNIPAAm structures by controlling process parameters of PμSL. In addition, we demonstrate improvement of mechanical properties of PNIPAAm by introducing ionic crosslinks into 3D printed PNIPAAm structures to form ionically and covalently crosslinked hybrid networks.

Autonomous self-healing polyisoprene elastomers with high modulus and good toughness based on the synergy of dynamic ionic crosslinks and highly disordered crystals

2020 ◽  
Vol 11 (41) ◽  
pp. 6549-6558
Author(s):  
Yohei Miwa ◽  
Mayu Yamada ◽  
Yu Shinke ◽  
Shoichi Kutsumizu
Keyword(s):  
Mechanical Properties ◽  
Room Temperature ◽  
Self Healing ◽  
High Modulus ◽  
Disordered Crystals ◽  
Ionic Crosslinks

We designed a novel polyisoprene elastomer with high mechanical properties and autonomous self-healing capability at room temperature facilitated by the coexistence of dynamic ionic crosslinks and crystalline components that slowly reassembled.

scholarly journals Studies on the Modification of Commercial Bisphenol-A-Based Epoxy Resin Using Different Multifunctional Epoxy Systems

2021 ◽  
Vol 2 (2) ◽  
pp. 419-430
Author(s):  
Ankur Bajpai ◽  
James R. Davidson ◽  
Colin Robert
Keyword(s):  
Mechanical Properties ◽  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Bisphenol A ◽  
Epoxy Resin ◽  
Tensile Fracture ◽  
Chemical Structures ◽  
Amino Phenol ◽  
Epoxy Systems

The tensile fracture mechanics and thermo-mechanical properties of mixtures composed of two kinds of epoxy resins of different chemical structures and functional groups were studied. The base resin was a bi-functional epoxy resin based on diglycidyl ether of bisphenol-A (DGEBA) and the other resins were (a) distilled triglycidylether of meta-amino phenol (b) 1, 6–naphthalene di epoxy and (c) fluorene di epoxy. This research shows that a small number of multifunctional epoxy systems, both di- and tri-functional, can significantly increase tensile strength (14%) over neat DGEBA while having no negative impact on other mechanical properties including glass transition temperature and elastic modulus. In fact, when compared to unmodified DGEBA, the tri-functional epoxy shows a slight increase (5%) in glass transition temperature at 10 wt.% concentration. The enhanced crosslinking of DGEBA (90 wt.%)/distilled triglycidylether of meta-amino phenol (10 wt.%) blends may be the possible reason for the improved glass transition. Finally, the influence of strain rate, temperature and moisture were investigated for both the neat DGEBA and the best performing modified system. The neat DGEBA was steadily outperformed by its modified counterpart in every condition.

Influence of slicing parameters on surface quality and mechanical properties of 3D-printed CF/PLA composites fabricated by FDM technique

2021 ◽  
pp. 1-18
Author(s):  
N. Vinoth Babu ◽  
N. Venkateshwaran ◽  
N. Rajini ◽  
Sikiru Oluwarotimi Ismail ◽  
Faruq Mohammad ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Surface Quality ◽  
3D Printed

scholarly journals Synthesis, Properties, and Biodegradability of Thermoplastic Elastomers Made from 2-Methyl-1,3-propanediol, Glutaric Acid and Lactide

Life ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 43
Author(s):  
Lamya Zahir ◽  
Takumitsu Kida ◽  
Ryo Tanaka ◽  
Yuushou Nakayama ◽  
Takeshi Shiono ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Glutaric Acid ◽  
Triblock Copolymers ◽  
Tensile Tests ◽  
Thermoplastic Elastomers ◽  
Proteinase K ◽  
Synthesis Properties

An innovative type of biodegradable thermoplastic elastomers with improved mechanical properties from very common and potentially renewable sources, poly(L-lactide)-b-poly(2-methyl-1,3-propylene glutarate)-b-poly(L-lactide) (PLA-b-PMPG-b-PLA)s, has been developed for the first time. PLA-b-PMPG-b-PLAs were synthesized by polycondensation of 2-methyl-1,3-propanediol and glutaric acid and successive ring-opening polymerization of L-lactide, where PMPG is an amorphous central block with low glass transition temperature and PLA is hard semicrystalline terminal blocks. The copolymers showed glass transition temperature at lower than −40 °C and melting temperature at 130–152 °C. The tensile tests of these copolymers were also performed to evaluate their mechanical properties. The degradation of the copolymers and PMPG by enzymes proteinase K and lipase PS were investigated. Microbial biodegradation in seawater was also performed at 27 °C. The triblock copolymers and PMPG homopolymer were found to show 9–15% biodegradation within 28 days, representing their relatively high biodegradability in seawater. The macromolecular structure of the triblock copolymers of PLA and PMPG can be controlled to tune their mechanical and biodegradation properties, demonstrating their potential use in various applications.

scholarly journals Fabrication of Polycaprolactone/Nano Hydroxyapatite (PCL/nHA) 3D Scaffold with Enhanced In Vitro Cell Response via Design for Additive Manufacturing (DfAM)

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1394
Author(s):  
Yong Sang Cho ◽  
So-Jung Gwak ◽  
Young-Sam Cho
Keyword(s):  
Mechanical Properties ◽  
Cell Response ◽  
Structural Characteristics ◽  
Structure Design ◽  
Compressive Modulus ◽  
Control Group ◽  
Design For Additive Manufacturing ◽  
3D Scaffold ◽  
3D Printed

In this study, we investigated the dual-pore kagome-structure design of a 3D-printed scaffold with enhanced in vitro cell response and compared the mechanical properties with 3D-printed scaffolds with conventional or offset patterns. The compressive modulus of the 3D-printed scaffold with the proposed design was found to resemble that of the 3D-printed scaffold with a conventional pattern at similar pore sizes despite higher porosity. Furthermore, the compressive modulus of the proposed scaffold surpassed that of the 3D-printed scaffold with conventional and offset patterns at similar porosities owing to the structural characteristics of the kagome structure. Regarding the in vitro cell response, cell adhesion, cell growth, and ALP concentration of the proposed scaffold for 14 days was superior to those of the control group scaffolds. Consequently, we found that the mechanical properties and in vitro cell response of the 3D-printed scaffold could be improved by kagome and dual-pore structures through DfAM. Moreover, we revealed that the dual-pore structure is effective for the in vitro cell response compared to the structures possessing conventional and offset patterns.

Physical property of 3D-printed sinusoidal pattern using shape memory TPU filament

2020 ◽  
Vol 90 (21-22) ◽  
pp. 2399-2410 ◽  
Author(s):  
Shahbaj Kabir ◽  
Hyelim Kim ◽  
Sunhee Lee
Keyword(s):  
Mechanical Properties ◽  
Tensile Test ◽  
Shape Memory ◽  
Fused Deposition Modeling ◽  
Loss Modulus ◽  
Thermoplastic Polyurethane ◽  
Heating Process ◽  
Fused Deposition ◽  
3D Printed ◽  
Sinusoidal Pattern

This study has investigated the physical properties of 3D-printable shape memory thermoplastic polyurethane (SMTPU) filament and its 3D-printed sinusoidal pattern obtained by fused deposition modeling (FDM) technology. To investigate 3D filaments, thermoplastic polyurethane (TPU) and SMTPU filament were examined by conducting infrared spectroscopy, x-ray diffraction (XRD), dynamic mechanical thermal analysis (DMTA), differential scanning calorimetry (DSC) and a tensile test. Then, to examine the 3D-printed sinusoidal samples, a sinusoidal pattern was developed and 3D-printed. Those samples went through a three-step heating process: (a) untreated state; (b) 5 min heating at 70°C, cooling for 30 min at room temperature; and (c) a repeat of step 2. The results obtained by the three different heating processes of the 3D-printed sinusoidal samples were examined by XRD, DMTA, DSC and the tensile test to obtain the effect of heating or annealing on the structural and mechanical properties. The results show significant changes in structure, crystallinity and thermal and mechanical properties of SMTPU 3D-printed samples due to the heating steps. XRD showed the increase in crystallinity with heating. In DMTA, storage modulus, loss modulus and the tan σ peak position also changed for various heating steps. The DSC result showed that the Tg for different steps of the SMTPU 3D-printed sample remained almost the same at around 51°C. The tensile property of the TPU 3D-printed sinusoidal sample decreased in terms of both load and elongation with increased heating processes, while for the SMTPU 3D-printed sinusoidal sample, the load decreased but elongation increased about 2.5 times.

Effect of molecular weight on mechanical properties and microstructure of 3D printed PEEK

2020 ◽  
Author(s):  
Qinfei Xu ◽  
Yingshuang Shang ◽  
Zilong Jiang ◽  
Zhaoyang Wang ◽  
Chenyi Zhou ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Molecular Weight ◽  
3D Printed
Sign in / Sign up

Export Citation Format

Share Document