A Quantitative Analysis of Kinetic Energy Harvesting for Hybrid Power Supplies

2012 ◽  
Author(s):  
Edwar Romero ◽  
Gerardo Carbajal ◽  
Robert Warrington ◽  
Michael Neuman
Keyword(s):  
Quantitative Analysis ◽  
Energy Harvesting ◽  
Figure Of Merit ◽  
Energy Harvester ◽  
Electronic Devices ◽  
Consumer Electronics ◽  
Power Supplies ◽  
Body Motion ◽  
Battery Life ◽  
Biomedical Monitoring

This study presents a quantitative analysis of experimental data for extracting energy from human body motion and its possibility of powering portable electronic devices, such as consumer electronics or biomedical monitoring sensors. Since portable electronic devices are typically limited by the size and lifespan of batteries, energy harvesting shows potential as alternative for extending battery life. The acceleration was collected experimentally from 10 subjects while walking and running at different velocities on a treadmill. The acceleration results were studied and a figure of merit consisting of the acceleration-squared-to-frequency was found to determine, in addition to the quality factor, as the important factors for optimal energy harvesting. It was determined that from average walking an energy harvester can produce a power output density greater than 1mW/cm3.

Arm Motion Dynamics to Excite a Mobile Energy Harvesting Autowinder

2020 ◽  
Author(s):  
Abby George ◽  
David Moline ◽  
John Wagner
Keyword(s):  
Energy Harvesting ◽  
Energy Harvester ◽  
Electronic Devices ◽  
Human Motion ◽  
Gear Train ◽  
Future Research ◽  
System Response ◽  
Battery Life ◽  
Arm Motion ◽  
Motion Dynamics

Abstract A mobile energy harvester device based on the inertial automatic winding mechanism found in watches is explored. Through normal human motion during walking and running, the arm travels a spatial path that can potentially be used for energy harvesting. The conceptual harvester consists of a rotary pendulum coupled to a small generator through a step-up gear train. The generator’s electrical output may be stored and utilized as a power source for portable electronic devices that require a smaller amount of power for operation. In this paper, the equations of motion governing the human arm motion dynamics and harvester pendulum excitation are fully derived. Two cases of human walking and running are considered to analyze the system response. A series of representative simulation studies have been conducted for representative arm motion to determine the potential energy. The energy available for harvesting was greater in the case of the human subject running at 2.06 mJ, while when walking it offered an output of 0.42 mJ for a 5 second time period. The two numerical results serve as a basis for building a mobile energy harvester for future research into a renewable device that can be used by humans to augment battery life for portable electronic devices.

Improvement of Figure of Merit Pb(Zr,Ti)O3–Pb(Zn,Ni,Nb)O3–Pb(In,Nb)O3 Piezoelectric Ceramics

2021 ◽  
Vol 21 (3) ◽  
pp. 1978-1983
Author(s):  
Bo Su Kim ◽  
Jae-Hoon Ji ◽  
Masao Kamiko ◽  
Seong Jin Kim ◽  
Jung-Hyuk Koh
Keyword(s):  
Dielectric Constant ◽  
Energy Harvesting ◽  
Lead Zirconate Titanate ◽  
Figure Of Merit ◽  
Energy Harvester ◽  
Relative Dielectric Constant ◽  
Lead Zirconate ◽  
Electric Voltage ◽  
Piezoelectric Energy ◽  
Piezoelectric Charge

Figure of merit the product of piezoelectric charge constant and the piezoelectric voltage constant—d33 × g33 in piezoelectric energy harvesting systems are critical measures in energy harvester applications. It is difficult to achieve high figure of merit because of the interdependence of d33 and the relative dielectric constant, εr. Until now, the prohibitive amount of effort required to solve this problem has led to it being considered an unsolvable issue. Lead zirconate titanate ceramic, Pb(Zr,Ti)O3, has been reported to exhibit high values of d33 and εr. However, to be employed as piezoelectric energy harvester, a candidate material is required to exhibit both high piezoelectric charge coefficient and high piezoelectric electric voltage coefficient simultaneously. To enhance the figure of merit of Pb(Zr,Ti)O3-based materials, dopants have also been considered. Pb(Zn,Ni,Nb)O3- added Pb(Zr,Ti)O3, Pb(Zr,Ti)O3–Pb(Zn,Ni,Nb)O3 ceramic has been reported to exhibit a high d33 value of 561 pC/N. It's dielectric constant has also been reported to be low at 1898. In this study, Pb(Zr,Ti)O3–Pb(Zn,Ni,Nb)O3–Pb(In,Nb)O3 was investigated in the context of enhancing the figure of merit of Pb(Zr,Ti)O3-based materials. During the proposed process, we increased the corresponding figure of merit by adding Pb(In,Nb)O3 material. Besides exhibiting a low dielectric constant, the Pb(In,Nb)O3 material was also observed to exhibit high d33 × g33 as the proposed doping increased the value of d33 greatly, while maintaining the dielectric constant (Yan, J., et al., 2019. Large engancement of trans coefficient in PZT-PZN energy harvesting system through introducing low εrPIN relaxor. Journal of the European Ceramic Society, 39, pp.2666–2672). Further, we conducted an optimization experiment by controlling the doping concentration and the sintering temperature.

Simply supported FPEDs connected by springs for broadband energy harvesting

2020 ◽  
Vol 64 (1-4) ◽  
pp. 201-210
Author(s):  
Yoshikazu Tanaka ◽  
Satoru Odake ◽  
Jun Miyake ◽  
Hidemi Mutsuda ◽  
Atanas A. Popov ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Evaluation Method ◽  
Energy Harvester ◽  
Vibrational Energy ◽  
Functional Materials ◽  
Vibration Energy ◽  
Theoretical Evaluation ◽  
Vibration Energy Harvester ◽  
Polyvinylidene Difluoride ◽  
Simply Supported

Energy harvesting methods that use functional materials have attracted interest because they can take advantage of an abundant but underutilized energy source. Most vibration energy harvester designs operate most effectively around their resonant frequency. However, in practice, the frequency band for ambient vibrational energy is typically broad. The development of technologies for broadband energy harvesting is therefore desirable. The authors previously proposed an energy harvester, called a flexible piezoelectric device (FPED), that consists of a piezoelectric film (polyvinylidene difluoride) and a soft material, such as silicon rubber or polyethylene terephthalate. The authors also proposed a system based on FPEDs for broadband energy harvesting. The system consisted of cantilevered FPEDs, with each FPED connected via a spring. Simply supported FPEDs also have potential for broadband energy harvesting, and here, a theoretical evaluation method is proposed for such a system. Experiments are conducted to validate the derived model.

scholarly journals Electrode and electrolyte configurations for low frequency motion energy harvesting based on reverse electrowetting

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Pashupati R. Adhikari ◽  
Nishat T. Tasneem ◽  
Russell C. Reid ◽  
Ifana Mahbub
Keyword(s):  
Energy Harvesting ◽  
Bias Voltage ◽  
Energy Harvester ◽  
Superior Performance ◽  
Maximum Output ◽  
Electrowetting On Dielectric ◽  
External Bias ◽  
Motion Energy ◽  
Ac Current ◽  
Self Powered

AbstractIncreasing demand for self-powered wearable sensors has spurred an urgent need to develop energy harvesting systems that can reliably and sufficiently power these devices. Within the last decade, reverse electrowetting-on-dielectric (REWOD)-based mechanical motion energy harvesting has been developed, where an electrolyte is modulated (repeatedly squeezed) between two dissimilar electrodes under an externally applied mechanical force to generate an AC current. In this work, we explored various combinations of electrolyte concentrations, dielectrics, and dielectric thicknesses to generate maximum output power employing REWOD energy harvester. With the objective of implementing a fully self-powered wearable sensor, a “zero applied-bias-voltage” approach was adopted. Three different concentrations of sodium chloride aqueous solutions (NaCl-0.1 M, NaCl-0.5 M, and NaCl-1.0 M) were used as electrolytes. Likewise, electrodes were fabricated with three different dielectric thicknesses (100 nm, 150 nm, and 200 nm) of Al2O3 and SiO2 with an additional layer of CYTOP for surface hydrophobicity. The REWOD energy harvester and its electrode–electrolyte layers were modeled using lumped components that include a resistor, a capacitor, and a current source representing the harvester. Without using any external bias voltage, AC current generation with a power density of 53.3 nW/cm2 was demonstrated at an external excitation frequency of 3 Hz with an optimal external load. The experimental results were analytically verified using the derived theoretical model. Superior performance of the harvester in terms of the figure-of-merit comparing previously reported works is demonstrated. The novelty of this work lies in the combination of an analytical modeling method and experimental validation that together can be used to increase the REWOD harvested power extensively without requiring any external bias voltage.

scholarly journals Piezoelectric Impact Energy Harvester Based on the Composite Spherical Particle Chain for Self-Powered Sensors

Sensors ◽  
2021 ◽  
Vol 21 (9) ◽  
pp. 3151
Author(s):  
Shuo Yang ◽  
Bin Wu ◽  
Xiucheng Liu ◽  
Mingzhi Li ◽  
Heying Wang ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Spherical Particle ◽  
Impact Energy ◽  
Energy Harvester ◽  
Composite Particle ◽  
Piezoelectric Energy Harvesting ◽  
Particle Chain ◽  
Piezoelectric Energy ◽  
Self Powered ◽  
Particle Chains

In this study, a novel piezoelectric energy harvester (PEH) based on the array composite spherical particle chain was constructed and explored in detail through simulation and experimental verification. The power test of the PEH based on array composite particle chains in the self-powered system was realized. Firstly, the model of PEH based on the composite spherical particle chain was constructed to theoretically realize the collection, transformation, and storage of impact energy, and the advantages of a composite particle chain in the field of piezoelectric energy harvesting were verified. Secondly, an experimental system was established to test the performance of the PEH, including the stability of the system under a continuous impact load, the power adjustment under different resistances, and the influence of the number of particle chains on the energy harvesting efficiency. Finally, a self-powered supply system was established with the PEH composed of three composite particle chains to realize the power supply of the microelectronic components. This paper presents a method of collecting impact energy based on particle chain structure, and lays an experimental foundation for the application of a composite particle chain in the field of piezoelectric energy harvesting.

Enhanced frequency synchronization for concurrent aeroelastic and base vibratory energy harvesting using a softening nonlinear galloping energy harvester

2021 ◽  
pp. 1045389X2110263
Author(s):  
Shun Chen ◽  
David Eager ◽  
Liya Zhao
Keyword(s):  
Energy Harvesting ◽  
Electromechanical Coupling ◽  
Energy Harvester ◽  
Poor Performance ◽  
Effective Bandwidth ◽  
Frequency Synchronization ◽  
Periodic Oscillations ◽  
Energy Harvesters ◽  
Paper Form ◽  
Excited Oscillation

This paper proposes a softening nonlinear aeroelastic galloping energy harvester for enhanced energy harvesting from concurrent wind flow and base vibration. Traditional linear aeroelastic energy harvesters have poor performance with quasi-periodic oscillations when the base vibration frequency deviates from the aeroelastic frequency. The softening nonlinearity in the proposed harvester alters the self-excited galloping frequency and simultaneously extends the large-amplitude base-excited oscillation to a wider frequency range, achieving frequency synchronization over a remarkably broadened bandwidth with periodic oscillations for efficient energy conversion from dual sources. A fully coupled aero-electro-mechanical model is built and validated with measurements on a devised prototype. At a wind speed of 5.5 m/s and base acceleration of 0.1 g, the proposed harvester improves the performance by widening the effective bandwidth by 300% compared to the linear counterpart without sacrificing the voltage level. The influences of nonlinearity configuration, excitation magnitude, and electromechanical coupling strength on the mechanical and electrical behavior are examined. The results of this paper form a baseline for future efficiency enhancement of energy harvesting from concurrent wind and base vibration utilizing monostable stiffness nonlinearities.

Multi-Stable Magnetic Spring-Based Energy Harvester Subject to Harmonic Excitation: Comparative Study and Experimental Evaluation

2018 ◽  
Author(s):  
Hieu Nguyen ◽  
Hamzeh Bardaweel
Keyword(s):  
Energy Harvesting ◽  
Kinetic Energy ◽  
Comparative Study ◽  
Experimental Evaluation ◽  
Chaotic Motion ◽  
Energy Harvester ◽  
Electric Energy ◽  
Harmonic Excitation ◽  
Jump Frequency ◽  
Piezoelectric Elements

The work presented here investigates a unique design platform for multi-stable energy harvesting using only interaction between magnets. A solid cylindrical magnet is levitated between two stationary magnets. Peripheral magnets are positioned around the casing of the energy harvester to create multiple stable positions. Upon external vibration, kinetic energy is converted into electric energy that is extracted using a coil wrapped around the casing of the harvester. A prototype of the multi-stable energy harvester is fabricated. Monostable and bistable configurations are demonstrated and fully characterized in static and dynamic modes. Compared to traditional multi-stable designs the harvester introduced in this work is compact, occupies less volume, and does not require complex circuitry normally needed for multi-stable harvesters involving piezoelectric elements. At 2.5g [m/s2], results from experiment show that the bistable harvester does not outperform the monostable harvester. At this level of acceleration, the bistable harvester exhibits intrawell motion away from jump frequency. Chaotic motion is observed in the bistable harvester when excited close to jump frequency. Interwell motion that yields high displacement amplitudes and velocities is absent at this acceleration.

Piezoelectric Energy Harvesting Design Principles for Materials and Structures: Material Figure‐of‐Merit and Self‐Resonance Tuning

2020 ◽  
Vol 32 (51) ◽  
pp. 2002208
Author(s):  
Hyun‐Cheol Song ◽  
Sun‐Woo Kim ◽  
Hyun Soo Kim ◽  
Dong‐Gyu Lee ◽  
Chong‐Yun Kang ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Figure Of Merit ◽  
Design Principles ◽  
Piezoelectric Energy Harvesting ◽  
Piezoelectric Energy ◽  
Resonance Tuning

Magnetoelectric Alternator

2016 ◽  
Vol 3 (2) ◽  
Author(s):  
R. V. Petrov ◽  
N. A. Kolesnikov ◽  
M. I. Bichurin
Keyword(s):  
Energy Harvesting ◽  
Magnetoelectric Effect ◽  
Electronic Devices ◽  
Synchronous Generator ◽  
Resonant Mode ◽  
Practical Application ◽  
Variable Voltage ◽  
Power Generation Equipment ◽  
High Power Consumption ◽  
Energy Harvesting Devices

AbstractThe article is devoted to researching the practical application of the magnetoelectric effect for the development of energy harvesting devices, in particular for the design of magnetoelectric synchronous generator. The energy harvesting devices are designed to provide by the energy of remote or nonvolatile electronic devices that don’t require the high power consumption. General dimensions of the generator were as follows: diameter of 12 cm, thickness of 2.4 cm. The model of generator comprising eight ME elements with dimensions of one element of 40×10×0.5 mm at the frequency of the alternating magnetic field of 38 Hz provides the output constant voltage of 1.12 V and current of 3.82 microamps. Variable voltage before the rectifier was of 1.7 V. Total generated power was of 4.28 µW. The studies of resonant and non-resonant mode of ME element were carried out. Resonance mode of ME element provides a much greater output power. Designed generator can be applied in the construction of wind power sets, hydrogenerators, turbogenerators and other power generation equipment.

scholarly journals Energy Harvesting Untethered Soft Electronic Devices (Adv. Healthcare Mater. 17/2021)

2021 ◽  
Vol 10 (17) ◽  
pp. 2170077
Author(s):  
Kyun Kyu Kim ◽  
Joonhwa Choi ◽  
Seung Hwan Ko
Keyword(s):  
Energy Harvesting ◽  
Electronic Devices
Sign in / Sign up

Export Citation Format

Share Document