Investigation of Soft and Hard Ceramics and Single Crystals for Resonant and Off-Resonant Piezoelectric Energy Harvesting

2010 ◽  
Author(s):  
Alper Erturk ◽  
Ho-Yong Lee ◽  
Daniel J. Inman
Keyword(s):  
Power Generation ◽  
Energy Harvesting ◽  
Resonance Frequency ◽  
Single Crystals ◽  
Energy Harvester ◽  
Low Frequency ◽  
Harmonic Excitation ◽  
Resonant Excitation ◽  
Piezoelectric Energy Harvesting ◽  
Piezoelectric Energy

Piezoelectric materials have received the most attention for vibration-to-electricity conversion over the last decade. Harmonic excitation is the most commonly investigated form of excitation in piezoelectric energy harvesting and it can be divided into two subgroups as resonant and off-resonant excitations. Although resonant excitation is preferred for extracting the maximum electrical power output from the device, there are several practical cases where it is not possible to excite the energy harvester at its resonance frequency (e.g. varying frequency excitations or very low frequency excitations where the input frequency is much lower than the fundamental resonance frequency). Several researchers have used soft piezoceramics (e.g. PZT-5A and PZT-5H) for power generation under resonant excitation. Typically, these soft piezoceramics have larger piezoelectric strain constant and larger elastic compliance compared to hard piezoceramics (e.g. PZT-4 and PZT-8). However, it is known that hard piezoceramics can have an order of magnitude larger mechanical quality factor compared to soft piezoceramics. Consequently, hard piezoceramics can generate more power under resonant excitation even though researchers have mostly focused on the soft piezoceramics. On the other hand, soft piezoceramics can generate more power for low frequency excitation below the resonance frequency due to their large effective piezoelectric stress constants. This difference is also the case for soft and hard single crystals (e.g. soft PMN-PZT versus hard PMN-PZT-Mn). In addition, single crystals can generate more power than ceramics at low off-resonant frequencies due to their large dynamic flexibilities (which is related to their large elastic compliances). This work investigates the specific advantages of soft and hard piezoceramics and single crystals for vibration-based energy harvesting. An experimentally validated piezoelectric energy harvester model is used to compare the power generation performances of soft and hard ceramics as well as soft and hard single crystals. The soft and the hard piezoceramics considered in this work are PZT-5H and PZT-8, respectively, while the soft and the hard single crystals considered here are PMN-PZT and PMN-PZT-Mn, respectively.

scholarly journals A Review on Piezoelectric Energy Harvesting: Materials, Methods, and Circuits

2019 ◽  
Vol 4 (1) ◽  
pp. 3-39 ◽  
Author(s):  
Shashank Priya ◽  
Hyun-Cheol Song ◽  
Yuan Zhou ◽  
Ronnie Varghese ◽  
Anuj Chopra ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Power Management ◽  
Energy Harvester ◽  
Piezoelectric Materials ◽  
Low Frequency ◽  
Small Scale ◽  
Piezoelectric Energy Harvesting ◽  
Wide Bandwidth ◽  
Piezoelectric Energy ◽  
Continuous Power

Abstract Piezoelectric microelectromechanical systems (PiezoMEMS) are attractive for developing next generation self-powered microsystems. PiezoMEMS promises to eliminate the costly assembly for microsensors/microsystems and provide various mechanisms for recharging the batteries, thereby, moving us closer towards batteryless wireless sensors systems and networks. In order to achieve practical implementation of this technology, a fully assembled energy harvester on the order of a quarter size dollar coin (diameter=24.26 mm, thickness=1.75 mm) should be able to generate about 100 μW continuous power from low frequency ambient vibrations (below 100 Hz). This paper reviews the state-of-the-art in microscale piezoelectric energy harvesting, summarizing key metrics such as power density and bandwidth of reported structures at low frequency input. This paper also describes the recent advancements in piezoelectric materials and resonator structures. Epitaxial growth and grain texturing of piezoelectric materials is being developed to achieve much higher energy conversion efficiency. For embedded medical systems, lead-free piezoelectric thin films are being developed and MEMS processes for these new classes of materials are being investigated. Non-linear resonating beams for wide bandwidth resonance are also reviewed as they would enable wide bandwidth and low frequency operation of energy harvesters. Particle/granule spray deposition techniques such as aerosol-deposition (AD) and granule spray in vacuum (GSV) are being matured to realize the meso-scale structures in a rapid manner. Another important element of an energy harvester is a power management circuit, which should maximize the net energy harvested. Towards this objective, it is essential for the power management circuit of a small-scale energy harvester to dissipate minimal power, and thus it requires special circuit design techniques and a simple maximum power point tracking scheme. Overall, the progress made by the research and industrial community has brought the energy harvesting technology closer to the practical applications in near future.

scholarly journals Piezoelectric Impact Energy Harvester Based on the Composite Spherical Particle Chain for Self-Powered Sensors

Sensors ◽  
2021 ◽  
Vol 21 (9) ◽  
pp. 3151
Author(s):  
Shuo Yang ◽  
Bin Wu ◽  
Xiucheng Liu ◽  
Mingzhi Li ◽  
Heying Wang ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Spherical Particle ◽  
Impact Energy ◽  
Energy Harvester ◽  
Composite Particle ◽  
Piezoelectric Energy Harvesting ◽  
Particle Chain ◽  
Piezoelectric Energy ◽  
Self Powered ◽  
Particle Chains

In this study, a novel piezoelectric energy harvester (PEH) based on the array composite spherical particle chain was constructed and explored in detail through simulation and experimental verification. The power test of the PEH based on array composite particle chains in the self-powered system was realized. Firstly, the model of PEH based on the composite spherical particle chain was constructed to theoretically realize the collection, transformation, and storage of impact energy, and the advantages of a composite particle chain in the field of piezoelectric energy harvesting were verified. Secondly, an experimental system was established to test the performance of the PEH, including the stability of the system under a continuous impact load, the power adjustment under different resistances, and the influence of the number of particle chains on the energy harvesting efficiency. Finally, a self-powered supply system was established with the PEH composed of three composite particle chains to realize the power supply of the microelectronic components. This paper presents a method of collecting impact energy based on particle chain structure, and lays an experimental foundation for the application of a composite particle chain in the field of piezoelectric energy harvesting.

Multimodal Energy Harvesting System: Piezoelectric and Electromagnetic

2008 ◽  
Vol 20 (5) ◽  
pp. 625-632 ◽  
Author(s):  
Yonas Tadesse ◽  
Shujun Zhang ◽  
Shashank Priya
Keyword(s):  
Energy Harvesting ◽  
Resonance Frequency ◽  
Permanent Magnet ◽  
Cantilever Beam ◽  
Piezoelectric Energy Harvesting ◽  
Prototype System ◽  
Finite Element Software ◽  
Piezoelectric Energy ◽  
Energy Harvesting System ◽  
Tip Mass

In this study, we report a multimodal energy harvesting device that combines electromagnetic and piezoelectric energy harvesting mechanism. The device consists of piezoelectric crystals bonded to a cantilever beam. The tip of the cantilever beam has an attached permanent magnet which, oscillates within a stationary coil fixed to the top of the package. The permanent magnet serves two purpose (i) acts as a tip mass for the cantilever beam and lowers the resonance frequency, and (ii) acts as a core which oscillates between the inductive coils resulting in electric current generation through Faraday's effect. Thus, this design combines the energy harvesting from two different mechanisms, piezoelectric and electromagnetic, on the same platform. The prototype system was optimized using the finite element software, ANSYS, to find the resonance frequency and stress distribution. The power generated from the fabricated prototype was found to be 0.25 W using the electromagnetic mechanism and 0.25 mW using the piezoelectric mechanism at 35 g acceleration and 20 Hz frequency.

Broadband Rotational Energy Harvesting Using Micro Energy Harvester

2018 ◽  
Author(s):  
Jui-Ta Chien ◽  
Yung-Hsing Fu ◽  
Chao-Ting Chen ◽  
Shun-Chiu Lin ◽  
Yi-Chung Shu ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Output Voltage ◽  
Energy Harvester ◽  
Low Frequency ◽  
Rotational Energy ◽  
Open Circuit ◽  
Maximum Output ◽  
Rotational Excitation ◽  
Rotating Speed ◽  
Piezoelectric Energy

This paper proposes a broadband rotational energy harvesting setup by using micro piezoelectric energy harvester (PEH). When driven in different rotating speed, the PEH can output relatively high power which exhibits the phenomenon of frequency up-conversion transforming the low frequency of rotation into the high frequency of resonant vibration. It aims to power self-powered devices used in the applications, like smart tires, smart bearings, and health monitoring sensors on rotational machines. Through the excitation of the rotary magnetic repulsion, the cantilever beam presents periodically damped oscillation. Under the rotational excitation, the maximum output voltage and power of PEH with optimal impedance is 28.2 Vpp and 663 μW, respectively. The output performance of the same energy harvester driven in ordinary vibrational based excitation is compared with rotational oscillation under open circuit condition. The maximum output voltage under 2.5g acceleration level of vibration is 27.54 Vpp while the peak output voltage of 36.5 Vpp in rotational excitation (in 265 rpm).

scholarly journals Piezoelectric Energy Harvesting with an Ultrasonic Vibration Source

Actuators ◽  
2019 ◽  
Vol 8 (1) ◽  
pp. 8
Author(s):  
Tao Li ◽  
Pooi Lee
Keyword(s):  
Energy Harvesting ◽  
High Power ◽  
High Frequency ◽  
Energy Harvester ◽  
Impedance Matching ◽  
Low Frequency ◽  
Vibration Source ◽  
Piezoelectric Energy ◽  
Power Ultrasonic ◽  
Ultrasonic Cutting

A piezoelectric energy harvester was developed in this paper. It is actuated by the vibration leakage from the nodal position of a high-power ultrasonic cutting transducer. The harvester was excited at a low displacement amplitude (0.73 µmpp). However, its operation frequency is quite high and reaches the ultrasonic range (24.4 kHz). Compared with another low frequency harvester (66 Hz), both theoretical and experimental results proved that the advantages of this high frequency harvester include (i) high current generation capability (up to 20 mApp compared to 1.3 mApp of the 66 Hz transducer) and (ii) low impedance matching resistance (500 Ω in contrast to 50 kΩ of the 66 Hz transducer). This energy harvester can be applied either in sensing, or vibration controlling, or simply energy harvesting in a high-power ultrasonic system.

Study of Cantilever Structures Based on Piezoelectric Materials for Energy Harvesting at Low Frequency of Vibration

2014 ◽  
Vol 976 ◽  
pp. 159-163 ◽  
Author(s):  
Roberto Ambrosio ◽  
Hector Gonzalez ◽  
Mario Moreno ◽  
Alfonso Torres ◽  
Rafael Martinez ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Output Power ◽  
Lead Zirconate Titanate ◽  
Maximum Output Power ◽  
Low Frequency ◽  
Electrical Contacts ◽  
Piezoelectric Energy Harvesting ◽  
Maximum Output ◽  
Coupling Coefficients ◽  
Piezoelectric Energy

In this work is presented a study of a piezoelectric energy harvesting device used for low power consumption applications operating at relative low frequency. The structure consists of a cantilever beam made by Lead Zirconate Titanate (PZT) layer with two gold electrodes for electrical contacts. The piezoelectric material was selected taking into account its high coupling coefficients. Different structures were analyzed with variations in its dimensions and shape of the cantilever. The devices were designed to operate at the resonance frequency to get maximum electrical power output. The structures were simulated using finite element (FE) software. The analysis of the harvesting devices was performed in order to investigate the influence of the geometric parameters on the output power and the natural frequency. To validate the simulation results, an experiment with a PZT cantilever with brass substrate was carried out. The experimental data was found to be very close to simulation data. The results indicate that large structures, in the order of millimeters, are the ideal for piezoelectric energy harvesting devices providing a maximum output power in the range of mW

Performance Analysis of Piezoelectric Energy Harvesting in Pavement: Laboratory Testing and Field Simulation

2019 ◽  
Vol 2673 (3) ◽  
pp. 115-124 ◽  
Author(s):  
Abbas F. Jasim ◽  
Hao Wang ◽  
Greg Yesner ◽  
Ahmad Safari ◽  
Pat Szary
Keyword(s):  
Energy Harvesting ◽  
Power Output ◽  
Laboratory Testing ◽  
Energy Harvester ◽  
Total Power ◽  
Piezoelectric Energy Harvesting ◽  
Loading Frequency ◽  
Vehicle Speed ◽  
Piezoelectric Energy ◽  
Energy Harvesting System

This study investigated the energy harvesting performance of a piezoelectric module in asphalt pavements through laboratory testing and multi-physics based simulation. The energy harvester module was assembled with layers of Bridge transducers and tested in the laboratory. A decoupled approach was used to study the interaction between the energy harvester and the surrounding pavement. The effects of embedment location, vehicle speed, and temperature on energy harvesting performance were investigated. The analysis findings indicate that the embedment location and vehicle speed affects the resulted power output of the piezoelectric energy harvesting system. The embedment depth of the energy module affects both the magnitude and frequency of stress pulse on top of the energy module induced by tire loading. On the other hand, higher vehicle speed causes greater loading frequency and thus greater power output; the effect of pavement temperature is negligible. The analysis of total power output before reaching fatigue failure of the energy module can be used to determine the optimum embedment location in the asphalt layer. The proposed energy harvesting system provides great potential to generate green energy from waste kinetic energy in roadway pavements. Field study is recommended to verify these findings with long-term performance monitoring of pavement with embedded energy harvesters.

On Mathematical Modeling of Piezoelectric Energy Harvesters

2014 ◽  
Vol 953-954 ◽  
pp. 655-658 ◽  
Author(s):  
Guang Qing Shang ◽  
Hong Bing Wang ◽  
Chun Hua Sun
Keyword(s):  
Mathematical Modeling ◽  
Energy Harvesting ◽  
Energy Harvester ◽  
Vibration Energy ◽  
Piezoelectric Energy Harvesting ◽  
Vibration Energy Harvester ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Energy Harvesting System ◽  
Piezoelectric Vibration

Energy harvesting system has become one of important areas of ​​research and develops rapidly. How to improve the performance of the piezoelectric vibration energy harvester is a key issue in engineering applications. There are many literature on piezoelectric energy harvesting. The paper places focus on summarizing these literature of mathematical modeling of piezoelectric energy harvesting, ranging from the linear to nonlinear, from early a single mechanical degree to piezoaeroelastic problems.

scholarly journals Experimental Study and Parameter Optimization of a Magnetic Coupled Piezoelectric Energy Harvester

2018 ◽  
Vol 8 (12) ◽  
pp. 2609 ◽  
Author(s):  
Xiaobo Rui ◽  
Yibo Li ◽  
Yue Liu ◽  
Xiaolei Zheng ◽  
Zhoumo Zeng
Keyword(s):  
Flux Density ◽  
Parameter Optimization ◽  
Energy Harvester ◽  
Fiber Composite ◽  
Electrical Power ◽  
Low Frequency ◽  
Harmonic Excitation ◽  
Lumped Parameter Model ◽  
Peak Output Power ◽  
Piezoelectric Energy

Piezoelectric energy harvesting is a promising way to develop self-sufficient systems. Structural design and parameter optimization are key issues to improve the performance in applications. This paper presents a magnetic coupled piezoelectric energy harvester to increase the output and bandwidth. A lumped parameter model considering the static position is established and various modes are simulated. This paper focuses on the “Low frequency repulsion mode”, which is more practical. The experiment platform is built with the Macro Fiber Composite (MFC) material, and the results are consistent with the analytical simulation. The optimization process of some key parameters, such as magnets spacing and flux density, is carried out. The results show that there is a corresponding optimal spacing for each flux density, which is positive correlated. With the optimized parameter design, the system achieves peak electrical power of 3.28 mW under the harmonic excitation of 4 m/s2. Compared with the conventional single cantilever harvester, the operated bandwidth is increased by 66.7% and the peak output power is increased by 35.0% in experiment.

Sign in / Sign up

Export Citation Format

Share Document