Shear Rate in the Couette Viscometer

1968 ◽  
Vol 12 (1) ◽  
pp. 5-11 ◽  
Author(s):  
Irvin M. Krieger
Keyword(s):  
Shear Rate ◽  
Couette Viscometer

Shear rate in the Couette viscometer with a narrow annular gap between cylinders. A new approximate formula

1975 ◽  
Vol 14 (11) ◽  
pp. 976-978 ◽  
Author(s):  
A. Apelblat ◽  
J. C. Healy ◽  
M. Joly
Keyword(s):  
Shear Rate ◽  
Approximate Formula ◽  
Couette Viscometer ◽  
Annular Gap

scholarly journals Rheological behavior of a bentonite mud

2020 ◽  
Vol 30 (1) ◽  
pp. 107-118
Author(s):  
Daniela Martins Marum ◽  
Maria Diná Afonso ◽  
Brian Bernardo Ochoa
Keyword(s):  
Shear Stress ◽  
Shear Rate ◽  
Temperature Effects ◽  
Drilling Fluids ◽  
Drilling Process ◽  
Gas Extraction ◽  
Pseudoplastic Fluid ◽  
Shear Rates ◽  
Couette Viscometer ◽  
Mud Flow

Abstract Predicting drilling fluids rheology is crucial to control/optimize the drilling process and the gas extraction from drilling fluids in logging systems. A Couette viscometer measured the apparent viscosity of a bentonite mud at various shear rates and temperatures. The bentonite mud behaved as a yield-pseudoplastic fluid, and a modified Herschel-Bulkley model predicted the shear rate and temperature effects upon the shear stress. A pipe viscometer was built to seek a correlation between the mud flow rate and the pressure drop and thereby determine refined Herschel-Bulkley parameters. Coupling a rheological model to a pipe viscometer enables the continuous acquisition of apparent viscosities of Newtonian or non-Newtonian fluids at a rig-site surface.

Adenosine Diphosphate-Induced Aggregation of Human Platelets in Flow Through Tubes: III. Shear and Extrinsic Fibrinogen-Dependent Effects

1994 ◽  
Vol 71 (01) ◽  
pp. 078-090 ◽  
Author(s):  
H L Goldsmith ◽  
M M Frojmovic ◽  
Susan Braovac ◽  
Fiona McIntosh ◽  
T Wong
Keyword(s):  
Shear Rate ◽  
Single Cells ◽  
Adenosine Diphosphate ◽  
Human Platelets ◽  
Size Analysis ◽  
Fibrinogen Concentration ◽  
Human Fibrinogen ◽  
Shear Rates ◽  
Rate Dependent ◽  
Induced Aggregation

SummaryThe effect of shear rate and fibrinogen concentration on adenosine diphosphate-induced aggregation of suspensions of washed human platelets in Poiseuille flow at 23°C was studied using a previously described double infusion technique and resistive particle counter size analysis (1). Using suspensions of multiple-centrifuged and -washed cells in Tyrodes-albumin [3 × 105 μl−1; (17)] with [fibrinogen] from 0 to 1.2μM, the, rate and extent of aggregation with 0.7 μM ADP in Tyrodes-albumin were measured over a range of mean transit times from 0.2 to 43 s, and at mean tube shear rates, Ḡ, = 41.9, 335 and 1,335 s−1. As measured by the decrease in singlet concentration, aggregation at 1.2 μM fibrinogen increased with increasing Ḡ up to 1,335 s1, in contrast to that previously reported in citratcd plasma, in which aggregation reached a maximum at Ḡ = 335 s−1. Without added fibrinogen, there was no aggregation at Ḡ = 41.9 s1; at Ḡ = 335 s1, there was significant aggregation but with an initial lag time, aggregation increasing further at Ḡ = 1,335 s−1. Without added fibrinogen, aggregation was abolished at all Ḡ upon incubation with the hexapeptide GRGDSP, but was almost unaffected by addition of an F(ab’)2 fragment of an antibody to human fibrinogen. Aggregation in the absence of added fibrinogen was also observed at 37°C. The activation of the multiple-washed platelets was tested using flow cytometry with the fluorescently labelled monoclonal antibodies FITC-PAC1 and FITC-9F9. It was shown that 57% of single cells in unactivated PRT expressed maximal GPIIb-IIIa fibrinogen receptors (MoAb PAC1) and 54% expressed pre-bound fibrinogen (MoAb 9F9), with further increases on ADP activation. However, incubation with GRGDSP and the F(ab’)2 fragment did not inhibit the prebound fibrinogen. Moreover, relatively unactivated cells (8% expressing receptor, 14% prebound fibrinogen), prepared from acidified cPRP by single centrifugation with 50 nM of the stable prostacyclin derivative, ZK 36 374, and resuspension in Tyrodes-albumin at 5 × 104 μl−1, aggregated with 2 and 5 μM ADP at Ḡ = 335 and 1,335 s−1 in the absence of added fibrinogen. We therefore postulate that a protein such as von Willebrand factor, secreted during platelet isolation or in flow at sufficiently high shear rates, may yield the observed shear-rate dependent aggregation without fibrinogen.

Platelet and Shear Rate Promote Tumor Cell Adhesion to Human Endothelial Extracellular Matrix - Absence of a Role for Platelet Cyclooxygenase

1989 ◽  
Vol 61 (03) ◽  
pp. 485-489 ◽  
Author(s):  
Eva Bastida ◽  
Lourdes Almirall ◽  
Antonio Ordinas
Keyword(s):  
Cell Adhesion ◽  
Shear Rate ◽  
Tumor Cell ◽  
Umbilical Vein ◽  
Blood Platelets ◽  
Flow Conditions ◽  
Tumor Cell Adhesion ◽  
Rate Dependent ◽  
Static Conditions

SummaryBlood platelets are thought to be involved in certain aspects of malignant dissemination. To study the role of platelets in tumor cell adherence to vascular endothelium we performed studies under static and flow conditions, measuring tumor cell adhesion in the absence or presence of platelets. We used highly metastatic human adenocarcinoma cells of the lung, cultured human umbilical vein endothelial cells (ECs) and extracellular matrices (ECM) prepared from confluent EC monolayers. Our results indicated that under static conditions platelets do not significantly increase tumor cell adhesion to either intact ECs or to exposed ECM. Conversely, the studies performed under flow conditions using the flat chamber perfusion system indicated that the presence of 2 × 105 pl/μl in the perfusate significantly increased the number of tumor cells adhered to ECM, and that this effect was shear rate dependent. The maximal values of tumor cell adhesion were obtained, in presence of platelets, at a shear rate of 1,300 sec-1. Furthermore, our results with ASA-treated platelets suggest that the role of platelets in enhancing tumor cell adhesion to ECM is independent of the activation of the platelet cyclooxygenase pathway.

The Effect of Red Blood Cells on the ADP-induced Aggregation of Human Platelets in Flow Through Tubes

1990 ◽  
Vol 63 (01) ◽  
pp. 112-121 ◽  
Author(s):  
David N Bell ◽  
Samira Spain ◽  
Harry L Goldsmith
Keyword(s):  
Platelet Aggregation ◽  
Shear Rate ◽  
Red Blood Cells ◽  
Blood Cells ◽  
Platelet Rich Plasma ◽  
Mean Transit Time ◽  
White Blood Cells ◽  
Aggregate Size ◽  
Human Platelets ◽  
Induced Aggregation

SummaryThe effect of red blood cells, rbc, and shear rate on the ADPinduced aggregation of platelets in whole blood, WB, flowing through polyethylene tubing was studied using a previously described technique (1). Effluent WB was collected into 0.5% glutaraldehyde and the red blood cells removed by centrifugation through Percoll. At 23°C the rate of single platelet aggregtion was upt to 9× greater in WB than previously found in platelet-rich plasma (2) at mean tube shear rates Ḡ = 41.9,335, and 1,920 s−1, and at both 0.2 and 1.0 µM ADP. At 0.2 pM ADP, the rate of aggregation was greatest at Ḡ = 41.9 s−1 over the first 1.7 s mean transit time through the flow tube, t, but decreased steadily with time. At Ḡ ≥335 s−1 the rate of aggregation increased between t = 1.7 and 8.6 s; however, aggregate size decreased with increasing shear rate. At 1.0 µM ADP, the initial rate of single platelet aggregation was still highest at Ḡ = 41.9 s1 where large aggregates up to several millimeters in diameter containing rbc formed by t = 43 s. At this ADP concentration, aggregate size was still limited at Ḡ ≥335 s−1 but the rate of single platelet aggregation was markedly greater than at 0.2 pM ADP. By t = 43 s, no single platelets remained and rbc were not incorporated into aggregates. Although aggregate size increased slowly, large aggregates eventually formed. White blood cells were not significantly incorporated into aggregates at any shear rate or ADP concentration. Since the present technique did not induce platelet thromboxane A2 formation or cause cell lysis, these experiments provide evidence for a purely mechanical effect of rbc in augmenting platelet aggregation in WB.

Generalized Transient Leveque Problem

1996 ◽  
Vol 61 (9) ◽  
pp. 1267-1284
Author(s):  
Ondřej Wein
Keyword(s):  
Mass Transfer ◽  
Exact Solution ◽  
Shear Rate ◽  
Transfer Problem ◽  
Numerical Data ◽  
Wall Shear Rate ◽  
Response Operator ◽  
Mass Transfer Problem ◽  
Finite Step ◽  
General Response

Response of an electrodiffusion friction sensor to a finite step of the wall shear rate is studied by numerically solving the relevant mass-transfer problem. The resulting numerical data on transient currents are treated further to provide reasonably accurate analytical representations. Existing approximations to the general response operator are checked by using the obtained exact solution.

scholarly journals Fiber Formation and Structural Development of HBA/HNA Thermotropic Liquid Crystalline Polymer in High-Speed Melt Spinning

Polymers ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 1134
Author(s):  
Bo Seok Song ◽  
Jun Young Lee ◽  
Sun Hwa Jang ◽  
Wan-Gyu Hahm
Keyword(s):  
Mechanical Properties ◽  
Shear Rate ◽  
High Speed ◽  
Melt Spinning ◽  
Liquid Crystalline Polymer ◽  
Liquid Crystalline ◽  
Crystalline Polymer ◽  
Fiber Formation ◽  
Structural Development ◽  
Thermotropic Liquid Crystalline Polymer

High-speed melt spinning of thermotropic liquid crystalline polymer (TLCP) resin composed of 4-hydroxybenzoic acid (HBA) and 2-hydroxy-6-napthoic acid (HNA) monomers in a molar ratio of 73/27 was conducted to investigate the characteristic structure development of the fibers under industrial spinning conditions, and the obtained as-spun TLCP fibers were analyzed in detail. The tensile strength and modulus of the fibers increased with shear rate in nozzle hole, draft in spin-line and spinning temperature and exhibited the high values of approximately 1.1 and 63 GPa, respectively, comparable to those of industrial as-spun TLCP fibers, at a shear rate of 70,000 s−1 and a draft of 25. X-ray diffraction demonstrated that the mechanical properties of the fibers increased with the crystalline orientation factor (fc) and the fractions of highly oriented crystalline and non-crystalline anisotropic phases. The results of structure analysis indicated that a characteristic skin–core structure developed at high drafts (i.e., spinning velocity) and low spinning temperatures, which contributed to weakening the mechanical properties of the TLCP fibers. It is supposed that this heterogeneous structure in the cross-section of the fibers was induced by differences in the cooling rates of the skin and core of the fiber in the spin-line.

scholarly journals Tanning Wastewater Treatment by Ultrafiltration: Process Efficiency and Fouling Behavior

Membranes ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 461
Author(s):  
Fu Yang ◽  
Zhengkun Huang ◽  
Jun Huang ◽  
Chongde Wu ◽  
Rongqing Zhou ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Shear Rate ◽  
Membrane Surface ◽  
Filtration Efficiency ◽  
Operating Conditions ◽  
Process Efficiency ◽  
Transmembrane Pressure ◽  
Leather Industry ◽  
Pore Blocking ◽  
The Impact

Ultrafiltration is a promising, environment-friendly alternative to the current physicochemical-based tannery wastewater treatment. In this work, ultrafiltration was employed to treat the tanning wastewater as an upstream process of the Zero Liquid Discharge (ZLD) system in the leather industry. The filtration efficiency and fouling behaviors were analyzed to assess the impact of membrane material and operating conditions (shear rate on the membrane surface and transmembrane pressure). The models of resistance-in-series, fouling propensity, and pore blocking were used to provide a comprehensive analysis of such a process. The results show that the process efficiency is strongly dependent on the operating conditions, while the membranes of either PES or PVDF showed similar filtration performance and fouling behavior. Reversible resistance was the main obstacle for such process. Cake formation was the main pore blocking mechanism during such process, which was independent on the operating conditions and membrane materials. The increase in shear rate significantly increased the steady-state permeation flux, thus, the filtration efficiency was improved, which resulted from both the reduction in reversible resistance and the slow-down of fouling layer accumulate rate. This is the first time that the fouling behaviors of tanning wastewater ultrafiltration were comprehensively evaluated, thus providing crucial guidance for further scientific investigation and industrial application.

scholarly journals Self-diffusion scalings in dense granular flows

Soft Matter ◽  
2021 ◽  
Author(s):  
Riccardo Artoni ◽  
Michele Larcher ◽  
James T. Jenkins ◽  
Patrick Richard
Keyword(s):  
Shear Rate ◽  
Solid Fraction ◽  
Granular Flows ◽  
The Self ◽  
Granular Temperature ◽  
Restitution Coefficient ◽  
Self Diffusion ◽  
Diffusivity Tensor ◽  
Dense Granular Flows

The self-diffusivity tensor in homogeneously sheared dense granular flows is anisotropic. We show how its components depend on solid fraction, restitution coefficient, shear rate, and granular temperature.

Sign in / Sign up

Export Citation Format

Share Document