The emission spectroscopy of some elements in high-temperature flames

1979 ◽  
Vol 44 (1) ◽  
pp. 69-79 ◽  
Author(s):  
Marie Pištěková ◽  
Jaroslav Jambor ◽  
Vítězslav Otruba ◽  
Lumír Sommer
Keyword(s):  
High Temperature ◽  
Atomic Absorption ◽  
Aluminium Alloys ◽  
Emission Spectroscopy ◽  
Scattered Light ◽  
Good Resolution ◽  
Matrix Elements ◽  
Chemical Interference ◽  
The Matrix ◽  
Small Chemical

The emission of atoms of a large number of elements in laminar high-temperature acetylene-N2O, H2-N2O, H2-O2, acetylene-air, and H2-air flames was studied; of these the most suitable are flame mixtures containing N2O. Methods were developed for determining Ca, Sr, Ba, for Cu, Cr, Mn and Ni in steels and for Cu, Fe, Mn and Ni in aluminium alloys using an acetylene-N2O flame. A small chemical interference for the matrix elements was found provided that a monochromator with good resolution and with a small amount of scattered light was employed. These conditions are fulfilled by most modern atomic absorption instruments with which comparable results are obtained.

Effect of High Temperature on Wear Behavior of Stir Cast Aluminium/Boron Carbide Composites

2020 ◽  
Vol 22 (4) ◽  
pp. 1031-1046
Author(s):  
X. Canute ◽  
M. C. Majumder
Keyword(s):  
High Temperature ◽  
Wear Rate ◽  
Boron Carbide ◽  
Wear Behavior ◽  
Base Alloy ◽  
Weight Fraction ◽  
Sliding Velocity ◽  
Wear Properties ◽  
High Temperature Wear ◽  
The Matrix

AbstractThe need for development of high temperature wear resistant composite materials with superior mechanical properties and tribological properties is increasing significantly. The high temperature wear properties of aluminium boron carbide composites was evaluated in this investigation. The effect of load, sliding velocity, temperature and reinforcement percentage on wear rate was determined by the pin heating method using pin heating arrangement. The size and structure of base alloy particles change considerably with an increase of boron carbide particles. The wettability and interface bonding between the matrix and reinforcement enhanced by the addition of potassium flurotitanate. ANOVA technique was used to study the effect of input parameters on wear rate. The investigation reveals that the load had higher significance than sliding velocity, temperature and weight fraction. The pin surface was studied with a high-resolution scanning electron microscope. Regression analysis revealed an extensive association between control parameters and response. The developed composites can be used in the production of automobile parts requiring high wear, frictional and thermal resistance.

scholarly journals On the Modular Operator of Mutli-component Regions in Chiral CFT

2021 ◽  
Author(s):  
Stefan Hollands
Keyword(s):  
Field Theory ◽  
Integral Equation ◽  
Hilbert Problem ◽  
Matrix Elements ◽  
New Approach ◽  
Conformal Field ◽  
The Matrix ◽  
Kms Condition ◽  
Modular Operator ◽  
Riemann Hilbert Problem

AbstractWe introduce a new approach to find the Tomita–Takesaki modular flow for multi-component regions in general chiral conformal field theory. Our method is based on locality and analyticity of primary fields as well as the so-called Kubo–Martin–Schwinger (KMS) condition. These features can be used to transform the problem to a Riemann–Hilbert problem on a covering of the complex plane cut along the regions, which is equivalent to an integral equation for the matrix elements of the modular Hamiltonian. Examples are considered.

scholarly journals Analytical angular solutions for the atom–diatom interaction potential in a basis set of products of two spherical harmonics: two approaches

2021 ◽  
Author(s):  
Mariusz Pawlak ◽  
Marcin Stachowiak
Keyword(s):  
Spherical Harmonics ◽  
Interaction Potential ◽  
Chem Phys ◽  
Basis Set ◽  
Matrix Elements ◽  
Trigonometric Functions ◽  
Variational Theory ◽  
Molecular Collision ◽  
The Matrix ◽  
Analytical Expressions

AbstractWe present general analytical expressions for the matrix elements of the atom–diatom interaction potential, expanded in terms of Legendre polynomials, in a basis set of products of two spherical harmonics, especially significant to the recently developed adiabatic variational theory for cold molecular collision experiments [J. Chem. Phys. 143, 074114 (2015); J. Phys. Chem. A 121, 2194 (2017)]. We used two approaches in our studies. The first involves the evaluation of the integral containing trigonometric functions with arbitrary powers. The second approach is based on the theorem of addition of spherical harmonics.

High Temperature Mechanical Properties of Ni-Al-Cr Based Alloys with Refractory Alloying Elements

2006 ◽  
Vol 510-511 ◽  
pp. 358-361
Author(s):  
Won Yong Kim ◽  
Han Sol Kim ◽  
In Dong Yeo ◽  
Mok Soon Kim
Keyword(s):  
High Temperature ◽  
Volume Fraction ◽  
Lattice Parameter ◽  
Alloying Elements ◽  
Solid Solution Hardening ◽  
High Temperature Strength ◽  
High Temperature Mechanical Properties ◽  
Die Materials ◽  
The Matrix ◽  
Effective Role

We report on advanced Ni3Al based high temperature structural alloys with refractory alloying elements such as Zr and Mo to be apllied in the fields of die-casting and high temperature press forming as die materials. The duplex microstructure consisting of L12 structured Ni3Al phase and Ni5Zr intermetallic dispersoids was observed to display the microstructural feature for the present alloys investigated. Depending on alloying elements, the volume fraction of 2nd phase was measured to be different, indicating a difference in solid solubility of alloying elements in the matrix γ’ phase. Lattice parameter of matrix phase increased with increasing content of alloying elements. In the higher temperature region more than 973K, the present alloys appeared to show their higher strength compared to those obtained in conventional superalloys. On the basis of experimental results obtained, it is suggested that refractory alloying elements have an effective role to improve the high temperature strength in terms of enhanced thermal stability and solid solution hardening.

scholarly journals Towards high-temperature applications of aluminium alloys enabled by additive manufacturing

2021 ◽  
pp. 1-48
Author(s):  
Richard A. Michi ◽  
Alex Plotkowski ◽  
Amit Shyam ◽  
Ryan R. Dehoff ◽  
Sudarsanam Suresh Babu
Keyword(s):  
High Temperature ◽  
Additive Manufacturing ◽  
Aluminium Alloys ◽  
Temperature Applications

scholarly journals Homogenisation Efficiency Assessed with Microstructure Analysis and Hardness Measurements in the EN AW 2011 Aluminium Alloy

Metals ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1211
Author(s):  
Maja Vončina ◽  
Aleš Nagode ◽  
Jožef Medved ◽  
Irena Paulin ◽  
Borut Žužek ◽  
...  
Keyword(s):  
Experimental Data ◽  
Image Analysis ◽  
Phase Equilibrium ◽  
Aluminium Alloy ◽  
Phase Formation ◽  
Aluminium Alloys ◽  
Eutectic Phase ◽  
The Matrix ◽  
Equilibrium Solidification ◽  
Homogenisation Process

When extruding the casted rods from EN AW 2011 aluminium alloys, not only their homogenized structure, but also their extrudable properties were significantly influenced by the hardness of the alloy. In this study, the object of investigations was the EN AW 2011 aluminium alloy, and the effect of homogenisation time on hardness was investigated. First, homogenisation was carried out at 520 °C for different times, imitating industrial conditions. After homogenisation, the samples were analysed by hardness measurements and further characterised by microscopy and image analysis to verify the influence of homogenisation on the resulting microstructural constituents. In addition, non-equilibrium solidification was simulated using the program Thermo-Calc and phase formation during solidification was investigated. The homogenisation process enabled more rounded shape of the Al2Cu eutectic phase, equilibrium formation of the phases, and the precipitation in the matrix, leading to a significant increase in the hardness of the EN AW 2011 aluminium alloy. The experimental data revealed a suitable homogenisation time of 4–6 h at a temperature of 520 °C, enabling optimal extrusion properties.

Synthesize Ti3SiC2 and Ti3SiC2-Diamond Composites at High Pressure and High Temperature

2012 ◽  
Vol 512-515 ◽  
pp. 671-675 ◽  
Author(s):  
Ai Guo Zhou ◽  
Liang Li ◽  
Tai Chao Su ◽  
Shang Sheng Li
Keyword(s):  
High Pressure ◽  
High Temperature ◽  
Intermediate Products ◽  
Diamond Particles ◽  
Ternary Carbide ◽  
The Matrix

Ti3SiC2, a ternary carbide, was proposed at this paper to use as the binder of polycrystalline diamonds to overcome the weaknesses of traditional metal binders and ceramic binders. Ti3SiC2was first reported to be in-situ synthesized under high pressure (4GPa) and at high temperature (1400°C) (HPHT) from the mixtures of Ti, Si and graphite powders or the mixture of Ti, SiC and graphite powders. Ti3SiC2-damond composites were also made at HPHT from the previous mixtures and diamond particles. TiCx, Ti5Si3Cxand TiSi2were main impurities and/or intermediate products of Ti3SiC2samples synthesized at HPHT. Ti3SiC2content increased as synthesized time increased from 10 min to 60 min. For as-synthesized composites, diamond particles were evenly distributed in matrix. The diamond particles are bonded well with the matrix by three types of interface.

Sign in / Sign up

Export Citation Format

Share Document