Flexural ductility of reinforced concrete beams with lap-spliced bars

2014 ◽  
Vol 41 (7) ◽  
pp. 594-604 ◽  
Author(s):  
Mehrollah Rakhshanimehr ◽  
M. Reza Esfahani ◽  
M. Reza Kianoush ◽  
B. Ali Mohammadzadeh ◽  
S. Roohollah Mousavi
Keyword(s):  
Reinforced Concrete ◽  
Bond Strength ◽  
Concrete Beams ◽  
Concrete Strength ◽  
Reinforced Concrete Beams ◽  
Transverse Reinforcement ◽  
Rc Beams ◽  
Flexural Ductility ◽  
Ductility Ratio ◽  
Strength And Ductility

In this paper, the flexural ductility of lap-spliced reinforced concrete (RC) beams is experimentally investigated. Twenty-four specimens were designed and manufactured for laboratory experiments. Concrete compressive strength, amount of transverse reinforcement over the splice length, and the diameter of longitudinal bars were selected as the main variables. The ductility of tested specimens is evaluated based on a previously defined ductility ratio. Results show that concrete strength and amount of transverse reinforcement over the splice have major effects on ductility. With an appropriate amount of transverse reinforcement, a satisfactory ductility response for different concrete strengths can be obtained. The CSA-A23.3-04 Standard provisions on bond strength and ductility of lap-spliced RC beams are evaluated and discussed. This study shows that the provisions in predicting the bond strength of lap-spliced concrete beams are adequate but may not achieve a satisfactory performance for ductility. An equation is proposed to achieve the appropriate ductility.

Effect of cracking localization on the structural ductility of normal strength and high strength reinforced concrete beams with steel fibers

2019 ◽  
Vol 10 (4) ◽  
pp. 457-469 ◽  
Author(s):  
Avraham N Dancygier ◽  
Yuri S Karinski
Keyword(s):  
Reinforced Concrete ◽  
Transition Point ◽  
Concrete Beams ◽  
High Strength ◽  
Reinforcement Ratio ◽  
Steel Fibers ◽  
Reinforced Concrete Beams ◽  
Flexural Ductility ◽  
Ductility Ratio ◽  
The Impact

This article presents a study of cracking localization in normal and high strength concrete beams that include steel fibers and the influence of this localization on their structural ductility. It is shown that for a given fiber type and content, as the reinforcement ratio ρ decreases, the cracking localization level increases. The effect of ρ on the level of cracking localization is more pronounced for low amounts of conventional reinforcement. This range of conventional reinforcement ratio is typical of slabs and especially for the commonly thicker protective slabs. Examination of the effect of the reinforcement ratio on the flexural ductility shows that there exists a transition point below which the ductility ratio decreases with  ρ. This transition point is well above the minimum reinforcement ratio, which is required in design codes for plain reinforced concrete elements. Empirical analysis of the relation between cracking localization and ductility ratio shows that up to the same transition point, as cracking localization increases, the flexural ductility decreases. Findings of this study show that the positive effect of adding fibers on enhancing the impact resistance of slabs and beams is conflicted by their negative influence on reducing the structural ductility for low reinforcement ratios, which are typical of protective slabs.

scholarly journals Modelling of Shear Strength for Reinforced Concrete Beams Provided with Side-Face Reinforcement in Dependence of Crack Inclination Angle

2019 ◽  
Vol 8 (6) ◽  
pp. 3941-3950
Keyword(s):  
Shear Strength ◽  
Reinforced Concrete ◽  
Inclination Angle ◽  
Concrete Beams ◽  
Concrete Strength ◽  
Reinforced Concrete Beams ◽  
Rc Beams ◽  
Shear Design ◽  
Web Reinforcement ◽  
Side Face

Shear behavior of reinforced concrete beams (RCbeams) is proved to be influenced by different parameters such as web reinforcement, beam size, shear span-to-depth ratio, concrete strength, and longitudinal reinforcement. In addition to these parameters, researches acknowledge the significant contribution of side-face reinforcement (SFR) in shear strength of RC-beams. This paper aims at proposing a new model for predicting shear strength of RC-beams that accounts for the contribution of SFR in shear strength along with the other above-mentioned parameters. An explicit formula is derived based on a mechanical conceptual model that considers the variation of the inclination angle of diagonal shear cracking. The derived formula is verified on the basis of numerical analysis results in addition to the available results from relevant experimental researches in literature. Reliability of the proposed formula is investigated compared to design provisions in different codes. Results demonstrates that the proposed formula is more capable of predicting shear strength of RC-beams provided with SFR rather than shear design codes. Consistency of the proposed formula in predicting shear strength implies that the mechanical concept, on which the proposed formula is derived, is in consistent with the actual mechanical behavior.

Laboratory Fast Corrosion Test of Plain Steel Bars in Concrete Beams

2012 ◽  
Vol 535-537 ◽  
pp. 1803-1806
Author(s):  
Shun Bo Zhao ◽  
Peng Bing Hou ◽  
Fu Lai Qu
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beams ◽  
Numerical Models ◽  
Concrete Strength ◽  
Reinforced Concrete Beams ◽  
Uniform Corrosion ◽  
Pure Bending ◽  
Accelerated Corrosion ◽  
Steel Bars ◽  
Bending Length

An experimental study was carried out to examine the non-uniform corrosion of plain steel bars in reinforced concrete beams partially placed in 5% sodium chloride solution under conditions of accelerated corrosion. 4 reinforced concrete beams with different concrete strength were made. The crack distributions of the beams due to pre-loads and expansion of corrosion product, and the sectional corrosion characteristics of plain steel bars are described in detail. The sectional area loss relating to mass loss and change along pure bending length of the beams are discussed. These can be used as the basis of test for further studies to build the numerical models of serviceability of corroded reinforced concrete beams.

Reliability-Based Balanced Condition for Strengthened RC Beams

2013 ◽  
Vol 756-759 ◽  
pp. 25-28 ◽  
Author(s):  
Chun Xia Li ◽  
Zhi Sheng Ding ◽  
Shi Lin Yan ◽  
Jun Ming Chen
Keyword(s):  
Reinforced Concrete ◽  
Carbon Fiber ◽  
Stress Distribution ◽  
Tensile Strain ◽  
Concrete Beams ◽  
Reinforced Concrete Beams ◽  
Experimental Result ◽  
Rc Beams ◽  
Yield Strain ◽  
Reliability Indicator

Based on the experimental result of the flexure capability of reinforced concrete beams strengthened by carbon fiber sheets, the stress distribution changes only after steel yielding and carbon fiber sheets function better. However serious the extent of the damage is before strengthened, the tensile strain of main steel reaches about 1.6 times of the yield strain for the secondary grade of steel as failure happens. To satisfy the object reliability indicator, reliability is analyzed using the ratio of the steel strain at the balanced failure to the yield strain as variable to obtain its optimum value, which is coincide with the experimental result, and makes better consistency between calculated reliability indicator and object reliability indicator.

scholarly journals RETROFITTING AND DACTILITY OF REINFORCED CONCRETE BEAMS USING AN EXTERNAL REINFORCEMENT METHOD

2019 ◽  
Vol 3 (2) ◽  
pp. 135
Author(s):  
Novita Ike Triyuliani ◽  
Sri Murni Dewi ◽  
Lilya Susanti
Keyword(s):  
Reinforced Concrete ◽  
Ultimate Load ◽  
Concrete Beams ◽  
Concrete Block ◽  
Steel Reinforcement ◽  
Reinforced Concrete Beams ◽  
Building Structures ◽  
Average Increase ◽  
External Reinforcement ◽  
Strength And Ductility

The innovations strengthening building structures are important topics. Failure in structures such as beams and columns due to time, re-functions of a building, even initial design errors that are weak or lack the safety factor of a building structure. External reinforced concrete beams are one of the beams currently being developed. It is a concrete block with reinforcement of steel reinforcement on the outer (external) of the beam. This study aims to determine the index of increasing beam strength and ductility after retrofitting external steel reinforcement, which has the dimension of beams 15 x 15 x 100 cm, repeating 12 pcs, with external reinforcement each 6 pcs 2Ø6 and 3Ø6. The results from this study are an increasing the index of beam flexural strength after retrofit with external steel reinforcement. Meanwhile, beams after retrofit with 2Ø6 external steel have an average increase index of 1.25 and 1.21 while for external steel 3Ø6 are 1.29 and 1.60 respectively. The ductility depends on the value of ultimate load and maximum deflection that occurs, where the ductility value for the comparison of each specimen experiences a reduction in the average ductility value with 2Ø6 external steel which is 37.74% and 70.95% while with 3Ø6 external steel is 61,65% and 60.62%. Berbagai inovasi upaya peningkatan kekuatan struktur bangunan telah menjadi bahasan yang penting. Kegagalan pada struktur seperti balok dan kolom karena umur, alih fungsi suatu bangunan, bahkan kesalahan desain awal yang lemah atau kurang memenuhi faktor keamanan suatu struktur bangunan. Balok beton bertulangan eksternal adalah salah satu balok yang sedang dikembangkan pada saat ini, yaitu balok beton dengan perkuatan tulangan baja di sisi terluar (eksternal). Penelitian ini bertujuan untuk mengetahui indeks peningkatan kekuatan balok dan daktilitas setelah dilakukan perbaikan menggunakan tulangan baja eksternal, dengan dimensi balok 15 × 15 × 100 cm berulang 12 buah, penambahan tulangan baja eksternal masingmasing 6 buah 2Ø6 dan 3Ø6. Hasil yang didapat dari penelitian ini adalah indeks peningkatan kekuatan lentur balok setelah dilakukan perbaikan menggunakan tulangan baja eksternal. Dimana balok setelah dilakukan perbaikan dengan baja eksternal 2Ø6 memiliki indeks peningkatan rata-rata 1,25 dan 1,21 sedangkan untuk baja eksternal 3Ø6 masing-masing 1,29 dan 1,60. Daktilitas tergantung dari nilai beban ultimit dan lendutan maksimum yang terjadi, dimana nilai daktilitas untuk perbandingan tiap benda uji mengalami reduksi nilai daktilitas rata-rata dengan baja eksternal 2Ø6 yaitu sebesar 37,74% dan 70,95% sedangkan dengan baja eksternal 3Ø6 sebesar 61,65% dan 60,62%.

scholarly journals DUCTILITY RESPONSE OF HYBRID FIBRE REINFORCED CONCRETE BEAMS

2018 ◽  
pp. 174-179 ◽  
Author(s):  
Eswari Natarajan
Keyword(s):  
Reinforced Concrete ◽  
Ultimate Load ◽  
Concrete Beams ◽  
Volume Fraction ◽  
Fibre Volume ◽  
Reinforced Concrete Beams ◽  
Fibre Reinforced Concrete ◽  
Hybrid Fibre ◽  
Service Load ◽  
Strength And Ductility

Abstract: The effect of fibre content on the Strength and ductility behaviour of hybrid fibre reinforced concrete (HFRC) beams having different fibre volume fractions was investigated. The parameters of this investigation included service load, ultimate load, service load deflection, ultimate load deflection, crack width, deflection ductility and energy ductility. The fibre volume fraction (Vf) ranged from 0.0 to 2.0 percent. Steel and polyolefin fibres were combined in different proportions and their impact on the above parameters was studied. The ductile response of hybrid fibre reinforced concrete beams was compared with that of control beam. The test results show that addition of 2.0 percent by volume of hybrid fibres improve the strength and ductility appreciably. Empirical expressions for predicting the strength and ductility of hybrid fibre reinforced concrete (HFRC) are proposed based on regression analysis. A close agreement has been obtained between the predicted and experimental results.

scholarly journals Seismic Behaviors of Concrete Beams Reinforced with Steel-FRP Composite Bars under Quasi-Static Loading

2018 ◽  
Vol 8 (10) ◽  
pp. 1913 ◽  
Author(s):  
Tong-Liang Xiao ◽  
Hong-Xing Qiu ◽  
Jia-Le Li
Keyword(s):  
Reinforced Concrete ◽  
Seismic Performance ◽  
Concrete Beams ◽  
Concrete Strength ◽  
Reinforced Concrete Beams ◽  
Ultimate Capacity ◽  
Shear Span ◽  
Frp Composite ◽  
Drift Ratio ◽  
Seismic Behaviors

Steel-fiber reinforced polymer (FRP) composite bar (SFCB) is a new composite material with good corrosion resistance and designable post-yield stiffness. Substitution of steel bar with SFCB can greatly increase the durability and ultimate capacity associated with seismic performance. First, the method and main results of the experiment are briefly introduced, then a simplified constitutive model of composite bar material was applied to simulate the seismic behaviors of the concrete beams reinforced with SFCBs by fiber element modeling. The simulation results were found to be in good agreement with test results, indicating that the finite element model is reasonable and accurate in simulating the seismic behaviors of beams reinforced with SFCB. Based on the numerical simulation method, a parametric study was then conducted. The main variable parameters were the FRP type in composite bars (i.e., basalt, carbon FRP and E-glass FRP), the concrete strength, basalt FRP (BFRP) content in SFCBs and shear span ratio. Seismic behaviors such as load-displacement pushover curves, seismic ultimate capacity and its corresponding drift ratio of the SFCBs reinforced concrete beams were also evaluated. The results showed that (1) the fiber type of the composite bar had a great impact on the mechanical properties of the beam, among which the beam reinforced with BFRP composite bar has higher seismic ultimate capacity and better ductility. With the increase of the fiber bundle in the composite bar, the post-yield stiffness and ultimate capacity of the component increase and the ductility is better; (2) at the pre-yield stage, concrete strength has little influence on the seismic performance of concrete beams while after yielding, the seismic ultimate capacity and post-yielding stiffness of specimens increased slowly with the increase in concrete strength, however, the ductility was reduced accordingly; (3) as the shear span ratio of beams increased from 3.5 to 5.5, the seismic ultimate capacity decreased gradually while the ultimate drift ratio increased by more than 50%. Through judicious setting of the fiber content and shear span ratio of the composite bar reinforced concrete beam, concrete beams reinforced with composite bars can have good ductility while maintaining high seismic ultimate capacity.

Finite Element Analysis of Shear Strength of Reinforced Concrete Beams after Fire

2013 ◽  
Vol 671-674 ◽  
pp. 474-478 ◽  
Author(s):  
Kai Xiang ◽  
Guo Hui Wang ◽  
Bi Zhao
Keyword(s):  
Finite Element ◽  
Shear Strength ◽  
Reinforced Concrete ◽  
Exposure Time ◽  
Concrete Strength ◽  
Reinforced Concrete Beams ◽  
Rc Beams ◽  
Fire Exposure ◽  
Shear Span ◽  
Strength And Stiffness

Shear strength and stiffness of fire-damaged reinforced concrete (RC) beams were researched. The nonlinear finite element method (FEM) was developed to simulate shear strength of fire-damaged RC beams. Considering mechanical properties deterioration of concrete and steel reinforcing bar, the parameters of fire-damaged RC beams, including fire exposure time, shear span to depth ratios, concrete strength, diameters of stirrups and spacing of stirrups, were analyzed. Based on numerical analysis, the change of shear strength and stiffness of fire-damaged RC beams were identified. The results showed that shear strength and stiffness of fire-damaged RC beams changed under different parameters. With increase of fire exposure time or increase of shear span to depth ratio or decrease of concrete strength, shear strength and stiffness of fire-damaged RC beams descended obviously. With decrease of diameters of stirrups or increase of spacing of stirrups, shear strength of fire-damaged RC beams descended gradually, but stiffness of fire-damaged RC beams had little change.

Sign in / Sign up

Export Citation Format

Share Document