Effect of particle size and strain conditions on the strength of crushed basalt

1983 ◽  
Vol 20 (4) ◽  
pp. 706-717 ◽  
Author(s):  
Mosaid Al-Hussaini
Keyword(s):  
Particle Size ◽  
Stress Level ◽  
Level Density ◽  
Triaxial Compression ◽  
Volumetric Strain ◽  
Confining Pressure ◽  
Strain Diagram ◽  
Compression Tests ◽  
Cohesionless Soils ◽  
Lower Shear

This paper describes the results of an investigation carried out to study the influence of particle size, stress level, density, method of consolidation, and strain conditions on the strength and compressibility of crushed basalt. All specimens were prepared at medium or high density, consolidated isotropically or under K0 consolidation, and sheared under effective confining pressure ranging from 443 to 2297 kPa. The material used in the test program had a straight line grain size distribution with maximum particle size ranges from 0.63 to 76.2 mm and minimum particle size equivalent to No. 30 U.S. standard sieve size:The tests indicated that an increase in the particle size (i.e., gradation) increases the strength and decreases the axial and the volumetric strain at failure. The study indicated further that the crushed basalt under triaxial compression has a lower shear strength than when sheared under plane strain conditions. Particles crushed were significantly influenced by the stress level and gradation and to a lesser degree by density of material. Keywords: cohesionless soils, density (mass/volume), shear tests, stress–strain diagram, compression tests, rockfill dams.

scholarly journals The influence of particle breakage on stress-dilatancy relationship for granular soils

2019 ◽  
Vol 92 ◽  
pp. 09004 ◽  
Author(s):  
Zenon Szypcio
Keyword(s):  
Internal Energy ◽  
Stress Level ◽  
Triaxial Compression ◽  
Volumetric Strain ◽  
Stress Path ◽  
State Theory ◽  
Particle Breakage ◽  
Compression Tests ◽  
Particle Crushing ◽  
Soil Gradation

The influence of particle breakage on soil behaviour is important from theoretical and practical perspectives. Particle breakage changes the internal energy in two ways. First, internal energy is consumed for particle crushing and second, the internal energy changes because of additional volumetric strain caused by particle crushing. These two effects may be quantified by use of Frictional State Theory. The analysed drained triaxial compression tests of Toyoura sand, gravel and Dog's Bay sand at different stress level and stress path revealed that the effect of particle breakage is a function of soil gradation, strength of soil grains, stress level and stress path.

Mechanical behaviour of powders using a medium pressure flexible boundary cubical triaxial tester

2003 ◽  
Vol 217 (3) ◽  
pp. 233-241 ◽  
Author(s):  
F Li ◽  
V M Puri
Keyword(s):  
Shear Modulus ◽  
Mechanical Behaviour ◽  
Triaxial Compression ◽  
Three Dimensional ◽  
Volumetric Strain ◽  
Confining Pressure ◽  
Alumina Powder ◽  
Medium Pressure ◽  
Mean Pressure ◽  
Confining Pressures

A medium pressure (<21 MPa) flexible boundary cubical triaxial tester was designed to measure the true three-dimensional response of powders. In this study, compression behaviour and strength of a microcrystalline cellulose powder (Avicel® PH102), a spray-dried alumina powder (A16SG), and a fluid-bed-granulated silicon nitride based powder (KY3500) were measured. To characterize the mechanical behaviour, three types of triaxial stress paths, that is, the hydrostatic triaxial compression (HTC), the conventional triaxial compression (CTC), and the constant mean pressure triaxial compression (CMPTC) tests were performed. The HTC test measured the volumetric response of the test powders under isostatic pressure from 0 to 13.79MPa, during which the three powders underwent a maximum volumetric strain of 40.8 per cent for Avicel® PH102, 30.5 per cent for A16SG, and 33.0 per cent for KY3500. The bulk modulus values increased 6.4-fold from 57 to 367MPa for Avicel® PH102, 3.7-fold from 174 to 637 MPa for A16SG, and 8.1-fold from 74 to 597MPa for KY3500, when the isotropic stress increased from 0.69 to 13.79 MPa. The CTC and CMPTC tests measured the shear response of the three powders. From 0.035 to 3.45MPa confining pressure, the shear modulus increased 28.7-fold from 1.6 to 45.9MPa for Avicel® PH102, 35-fold from 1.7 to 60.5MPa for A16SG, and 28.5-fold from 1.5 to 42.8MPa for KY3500. In addition, the failure stresses of the three powders increased from 0.129 to 4.41 MPa for Avicel® PH102, 0.082 to 3.62 MPa for A16SG, and 0.090 to 4.66MPa for KY3500, respectively, when consolidation pressure increased from 0.035 to 3.45MPa. In addition, the shear modulus and failure stress values determined from the CTC test at 2.07, 2.76, and 3.45MPa confining pressures are consistently greater than those from the CMPTC test at the same constant mean pressures. This observation demonstrates the influence of stress paths on material properties. The CTT is a useful tool for characterizing the three-dimensional response of powders and powder mixtures.

Experimental investigation of the effect of compliant pores on reservoir rocks under hydrostatic and triaxial compression stress states

2019 ◽  
Vol 56 (7) ◽  
pp. 983-991
Author(s):  
Hua Yu ◽  
Kam Ng ◽  
Dario Grana ◽  
John Kaszuba ◽  
Vladimir Alvarado ◽  
...  
Keyword(s):  
Pore Pressure ◽  
Triaxial Compression ◽  
Matrix Material ◽  
Volumetric Strain ◽  
Confining Pressure ◽  
Differential Pressure ◽  
Sandstone Sample ◽  
Stress States ◽  
Rock Springs ◽  
Stage 1

The presence of compliant pores in rocks is important for understanding the stress–strain behaviors under different stress conditions. This paper describes findings on the effect of compliant pores on the mechanical behavior of a reservoir sandstone under hydrostatic and triaxial compression. Laboratory experiments were conducted at reservoir temperature on Weber Sandstone samples from the Rock Springs Uplift, Wyoming. Each experiment was conducted at three sequential stages: (stage 1) increase in the confining pressure while maintaining the pore pressure, (stage 2) increase in the pore pressure while maintaining the confining pressure, and (stage 3) application of the deviatoric load to failure. The nonlinear pore pressure – volumetric strain relationship governed by compliant pores under low confining pressure changes to a linear behavior governed by stiff pores under higher confining pressure. The estimated compressibilities of the matrix material in sandstone samples are close to the typical compressibility of quartz. Because of the change in pore structures during stage 1 and stage 2 loadings, the estimated bulk compressibilities of the sandstone sample under the lowest confining pressure decrease with increasing differential pressure. The increase in crack initiation stress is limited with increasing differential pressure because of similar total crack length governed by initial compliant porosity in sandstone samples.

scholarly journals Semi-empirical elastic–thermoviscoplastic model for clay

2016 ◽  
Vol 53 (10) ◽  
pp. 1583-1599 ◽  
Author(s):  
David Kurz ◽  
Jitendra Sharma ◽  
Marolo Alfaro ◽  
Jim Graham
Keyword(s):  
Stress Level ◽  
Axial Strain ◽  
Triaxial Compression ◽  
Compression Tests ◽  
One Dimensional ◽  
Load Duration ◽  
Compression Creep ◽  
Overconsolidated Clays ◽  
Semi Empirical ◽  
Triaxial Compression Tests

Clays exhibit creep in compression and shear. In one-dimensional compression, creep is commonly known as “secondary compression” even though it is also a significant component of deformations resulting from shear straining. It reflects viscous behaviour in clays and therefore depends on load duration, stress level, the ratio of shear stress to compression stress, strain rate, and temperature. Research described in the paper partitions strains into elastic (recoverable) and plastic (nonrecoverable) components. The plastic component includes viscous strains defined by a creep rate coefficient ψ that varies with plasticity index and temperature (T), but not with stress level or overconsolidation ratio (OCR). Earlier elastic–viscoplastic (EVP) models have been modified so that ψ = ψ(T) in a new elastic–thermoviscoplastic (ETVP) model. The paper provides a sensitivity analysis of simulated results from undrained (CIŪ) triaxial compression tests for normally consolidated and lightly overconsolidated clays. Axial strain rates range from 0.15%/day to 15%/day, and temperatures from 28 to 100 °C.

scholarly journals Researches on the Constitutive Models of Artificial Frozen Silt in Underground Engineering

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Yugui Yang ◽  
Feng Gao ◽  
Hongmei Cheng ◽  
Yuanming Lai ◽  
Xiangxiang Zhang
Keyword(s):  
Mechanical Characteristic ◽  
Stress Level ◽  
Strain Softening ◽  
Triaxial Compression ◽  
High Stress ◽  
Constitutive Models ◽  
Confining Pressure ◽  
Frozen Soil ◽  
Conventional Triaxial Compression ◽  
Shear Process

The researches on the mechanical characteristic and constitutive models of frozen soil have important meanings in structural design of deep frozen soil wall. In the present study, the triaxial compression and creep tests have been carried out, and the mechanical characteristic of frozen silt is obtained. The experiment results show that the deformation characteristic of frozen silt is related to confining pressure under conventional triaxial compression condition. The frozen silt presents strain softening in shear process; with increase of confining pressure, the strain softening characteristic gradually decreases. The creep curves of frozen silt present the decaying and the stable creep stages under low stress level; however, under high stress level, once the strain increases to a critical value, the creep strain velocity gradually increases and the specimen quickly happens to destroy. To reproduce the deformation behavior, the disturbed state elastoplastic and new creep constitutive models of frozen silt are developed. The comparisons between experimental results and calculated results from constitutive models show that the proposed constitutive models could describe the conventional triaxial compression and creep deformation behaviors of frozen silt.

scholarly journals Triaxial Compressive Failure Characteristics and Constitutive Model Study of Jurassic-Cretaceous Weakly Cemented Sandstone

2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
Jinlong Cai ◽  
Wei Zou
Keyword(s):  
Constitutive Model ◽  
Residual Strength ◽  
Triaxial Compression ◽  
Volumetric Strain ◽  
Ductile Failure ◽  
Mathematical Expression ◽  
Confining Pressure ◽  
Mining Area ◽  
Peak Strength ◽  
Correction Coefficient

A conventional triaxial compression test of Jurassic-Cretaceous typical weakly consolidated sandstone from a mining area in Ordos, China, was conducted using an MTS816 tester. Results showed that, before the peak, the rock had a distinct yield stage. When the specimen reached its peak strength, the strength decreased rapidly and showed an obvious brittle failure. When the confining pressure was increased to 15 MPa, the decrease of strength was slow and the rock tended toward ductile failure. With the increase of confining pressure, the cyclic strain initially increased slightly, whereas the volumetric strain increased greatly and the rock sample was in a compression state. When the load reached a critical value, the curve was reversely bent, resulting in volume expansion, whereas the peak strength, residual strength, and elastic modulus increased with confining pressure, and Poisson’s ratio decreased with the confining pressure. In the model based on macroscopic failure rock, the expression of the relationship between fracture angle and confining pressure provided a solid theoretical basis for the direction and failure mode of the macroscopic crack. Based on the rock strength theory and Weibull random distribution assumption of rock element strength, the damage variable correction coefficient was introduced when the residual strength was considered. Then, the mathematical expression of the 3D damage statistical constitutive model was established. Finally, the theoretical curve of the established constitutive model was compared with the triaxial test curve, which showed a high degree of coincidence.

scholarly journals Triaxial Testing of Geosynthetics Reinforced Tailings with Different Reinforced Layers

Materials ◽  
2020 ◽  
Vol 13 (8) ◽  
pp. 1943
Author(s):  
Fu Yi ◽  
Changbo Du
Keyword(s):  
Triaxial Compression ◽  
Friction Angle ◽  
Confining Pressure ◽  
Test Results ◽  
Compression Tests ◽  
Strength Index ◽  
Stress Strain ◽  
High Confining Pressure ◽  
Zhang Model ◽  
Triaxial Compression Tests

To evaluate the shear properties of geotextile-reinforced tailings, triaxial compression tests were performed on geogrids and geotextiles with zero, one, two, and four reinforced layers. The stress–strain characteristics and reinforcement effects of the reinforced tailings with different layers were analyzed. According to the test results, the geogrid stress–strain curves show hardening characteristics, whereas the geotextile stress–strain curves have strain-softening properties. With more reinforced layers, the hardening or softening characteristics become more prominent. We demonstrate that the stress–strain curves of geogrids and geotextile reinforced tailings under different reinforced layers can be fitted by the Duncan–Zhang model, which indicates that the pseudo-cohesion of shear strength index increases linearly whereas the friction angle remains primarily unchanged with the increase in reinforced layers. In addition, we observed that, although the strength of the reinforced tailings increases substantially, the reinforcement effect is more significant at a low confining pressure than at a high confining pressure. On the contrary, the triaxial specimen strength decreases with the increase in the number of reinforced layers. Our findings can provide valuable input toward the design and application of reinforced engineering.

scholarly journals Influence of fissure inclination and confining pressure on the local behaviour of natural clays

2019 ◽  
Vol 92 ◽  
pp. 03004
Author(s):  
Erika Tudisco ◽  
Claudia Vitone ◽  
Cristina Mondello ◽  
Gioacchino Viggiani ◽  
Stephen A. Hall ◽  
...  
Keyword(s):  
Volumetric Strain ◽  
Confining Pressure ◽  
Image Correlation ◽  
Compression Tests ◽  
Confinement Pressure ◽  
Santa Croce ◽  
Deformation Processes ◽  
Natural Clays ◽  
Scaly Clay

In this experimental study the influence of fissuring orientation and confinement pressure on the mechanical behaviour of natural clays is investigated. The tested material, the scaly clay from Santa Croce di Magliano (south of Italy), is characterised by an intense network of pre-existing fissures of single orientation. Several plane strain compression tests have been conducted, under different confinement pressures (i.e., from 50 to 600 kPa), on specimens having fissures with vertical, medium and horizontal inclination. Digital Image Correlation has been used to follow the deformation processes of the specimens throughout the tests by measuring incremental shear and volumetric strain maps. The results showed a strong coupling between the total confinement and the fissure inclination, that is controlling both the onset and the development of the patterns of the localisation processes. The new results have been compared with previous ones carried out on the same material without confinement. The comparison shed light on the role of total confinement that becomes particularly relevant from certain levels of pressures and fissuring inclination.

scholarly journals Experimental Investigation and Micromechanical Modeling of Elastoplastic Damage Behavior of Sandstone

Materials ◽  
2020 ◽  
Vol 13 (15) ◽  
pp. 3414
Author(s):  
Chaojun Jia ◽  
Qiang Zhang ◽  
Susheng Wang
Keyword(s):  
Damage Evolution ◽  
Triaxial Compression ◽  
Damage Model ◽  
Confining Pressure ◽  
Micromechanical Modeling ◽  
Compression Tests ◽  
Integration Algorithm ◽  
Damage Behavior ◽  
Plastic Strain Increment ◽  
Elastoplastic Damage

The mechanical behavior of the sandstone at the dam site is important to the stability of the hydropower station to be built in Southwest China. A series of triaxial compression tests under different confining pressures were conducted in the laboratory. The critical stresses were determined and the relationship between the critical stress and confining pressure were analyzed. The Young’s modulus increases non-linearly with the confining pressure while the plastic strain increment Nϕ and the dilation angle ϕ showed a negative response. Scanning electron microscope (SEM) tests showed that the failure of the sandstone under compression is a coupled process of crack growth and frictional sliding. Based on the experimental results, a coupled elastoplastic damage model was proposed within the irreversible thermodynamic framework. The plastic deformation and damage evolution were described by using the micromechanical homogenization method. The plastic flow is inherently driven by the damage evolution. Furthermore, a numerical integration algorithm was developed to simulate the coupled elastoplastic damage behavior of sandstone. The main inelastic properties of the sandstone were well captured. The model will be implemented into the finite element method (FEM) to estimate the excavation damaged zones (EDZs) which can provide a reference for the design and construction of such a huge hydropower project.

Effect of ageing on stiffness of very loose sand

2002 ◽  
Vol 39 (1) ◽  
pp. 149-156 ◽  
Author(s):  
J A Howie ◽  
T Shozen ◽  
Y P Vaid
Keyword(s):  
Soil Structure ◽  
Stress Ratio ◽  
Triaxial Compression ◽  
High Stress ◽  
Volumetric Strain ◽  
Compression Tests ◽  
Close Attention ◽  
Stress Ratios ◽  
Creep Modulus ◽  
Triaxial Compression Tests

The paper presents the results of laboratory triaxial compression tests to study the stiffness of very loose Fraser River sands. The stiffness has been shown to be very dependent on the time of confinement prior to shearing and the stress ratio at which the sample is aged. Higher stress ratios resulted in very low initial moduli with no ageing, but the moduli increased by several hundred percent during the first 1000 min of ageing. For ageing at a stress ratio of 1.0 (i.e., isotropic ageing), the initial moduli were higher than those for ageing at high stress ratios, but the stiffness increased by only about 60% during the first 1000 min of ageing. The rate of stiffness increase was approximately linear with the logarithm of time up to ageing times of 10 000 min (>1 week). Ageing at any stress ratio resulted in reduced contractive volumetric strain during subsequent shearing, reflecting a change in soil structure during ageing. The dεv /dεa ratio under triaxial compression loading decreased as the ageing stress ratio increased. The results suggest that close attention must be paid to the age of laboratory samples prepared to study the stress–strain response of sands at strains up to about 0.1%, particularly in studies on loose sand.Key words: sands, ageing, creep, modulus.

Sign in / Sign up

Export Citation Format

Share Document