Effect of soil properties and soil disturbance on frost heaving of mineral soil: a laboratory experiment

2006 ◽  
Vol 36 (11) ◽  
pp. 2885-2893 ◽  
Author(s):  
Michelle de Chantal ◽  
Hannu Rita ◽  
Urban Bergsten ◽  
Mikaell Ottosson Löfvenius ◽  
Harald Grip
Keyword(s):  
Laboratory Experiment ◽  
Repeated Measures ◽  
Sandy Loam ◽  
Mineral Soil ◽  
Fine Sand ◽  
Soil Disturbance ◽  
Coarse Sand ◽  
Loamy Sand ◽  
Frost Heaving ◽  
C And N

A laboratory experiment was done to identify the properties that make a substrate susceptible to frost heaving. Tests were carried out on nondisturbed soil cores (fresh and dry) of Ae and B horizons from sand, loamy sand, and sandy loam in a freezing cabinet (–3.5 °C). Cores were continuously supplied with water from below. Freezing tests were repeated after soil disturbance (V-shaped furrow, 50% increase in surface area). The effects of texture, horizon, drying, and disturbance on frost heaving were tested using repeated-measures analysis of variance with soil elements (organic Al, organic Fe, inorganic Al, inorganic Fe, C, and N) and soil fractions (clay, fine silt, coarse silt, fine sand, and coarse sand) as covariates. The effect of horizon was as important as that of texture, and soil disturbance increased frost heaving. Disturbed fresh B horizon from loamy sand and sandy loam heaved the most (soil expansion >5% in height), whereas nondisturbed dry Ae horizon, regardless of texture, and nondisturbed dry B horizon from sand heaved the least (soil expansion <0.8% in height). Soil elements and fractions had an impact on frost heaving, especially organic Al, although it was of a smaller magnitude. Therefore, it is suggested that seedbeds or planting substrates be prepared by exposing the nondisturbed Ae horizon only, that is, without exposing or disturbing the B horizon.

scholarly journals Determination of the Boundaries of the Compressible Strata When Conducting Engineering Surveys

2020 ◽  
Vol 24 (3) ◽  
pp. 79-87
Author(s):  
K. O. Dubrakova ◽  
V. A. Solodilova
Keyword(s):  
Sandy Loam ◽  
Physical And Mechanical Properties ◽  
Fine Sand ◽  
Coarse Sand ◽  
Adequate Accuracy ◽  
Practical Standpoint ◽  
The Cost ◽  
The Given ◽  
Main Influence

Purpose of research. Errors and inaccuracies in the preparation of deliverables based on the results of engineering surveys which are an integral and important part of the design and estimate documentation, can lead to irreversible consequences and significantly reduce the life of buildings and structures. The main difficulty in investigating soil physical and mechanical properties at a construction site is to determine the depth of excavation. This is due to the fact that an increase in the calculated depth leads to the increase in the cost of work, and its decrease leads to the risk of inaccuracies and errors in the design of foundations of buildings and structures. In accordance with the current regulatory documents, the excavation depth during soil investigation should be 1-2 meters below the boundary of the compressible strata. The condition on the basis of which the specified boundary is determined is provided. The development of a technique that allows determining the depth of the compressible strata at the stage of engineering surveying with adequate accuracy is an important task from a practical standpoint. Methods. Determining natural stress Ϭzg,0 as the product of foundation depth d and the specific gravity of the soil above the base ɣ′ІІ,  , taking into account the fact that the average pressure tends to the value of the estimated resistance of the soil, it is shown that physical-mechanical structure of the base soil exerts the main influence on the parameters of the compressible strata, and correspondingly, to the excavation depth value. In this case, the stresses transferred by the foundation of a building or structure have an indirect effect. Results. The maximum values of the depth of excavation for engineering and geological surveying for tight coarse sand, medium density and fineness sand, and fine sand and sandy loam are determined. Conclusion. It is concluded that the given technique allows determining the depth of excavation during engineering and geological surveying with an adequate accuracy.

scholarly journals Impacts of organic soil amendments on forage grass production under different soil conditions

2020 ◽  
Vol 29 (5) ◽  
Author(s):  
Tomas Persson ◽  
Wieslaw Szulc ◽  
Beata Rutkowska ◽  
Mats Höglind ◽  
Hans Martin Hanslin ◽  
...  
Keyword(s):  
Tall Fescue ◽  
Sandy Loam ◽  
Organic Amendments ◽  
Organic Soil ◽  
Coarse Sand ◽  
Loamy Sand ◽  
Control Treatment ◽  
Soil Conditions ◽  
Significant Yield ◽  
Grassland Productivity

Organic amendments can improve grassland productivity. Timothy and tall fescue were sown on a sandy loam and a coarse sand at Særheim, Norway, in September 2016 and on a loamy sand at Skierniewice, Poland, in April 2017, and cut and fertilised according to normal practices for the two regions from 2017 to 2019. At both sites, 0.75 kg DM m-2 of either digested or undigested manure (the latter with or without 2.9 kg biochar m-2) were incorporated prior to sowing. On the coarse sand at Særheim, total seasonal tall fescue yield in 2018 was 46–60% higher in the organic amendment treatments, and total seasonal timothy yield in the digestate treatment was 97% higher, than in the control treatment for the same species with only mineral fertiliser. On the sandy loam at Særheim and the loamy sand at Skierniewice, none of the amendments resulted in significant yield increments. These results indicate a clear effect on soil type on grassland biomass response to organic amendments.

Comparison of oxidoreductive enzyme activities in three coal tar creosote-contaminated soils

Soil Research ◽  
2019 ◽  
Vol 57 (8) ◽  
pp. 814 ◽  
Author(s):  
Arkadiusz Telesiński ◽  
Teresa Krzyśko-Łupicka ◽  
Krystyna Cybulska ◽  
Barbara Pawłowska ◽  
Robert Biczak ◽  
...  
Keyword(s):  
Contaminated Soils ◽  
Sandy Loam ◽  
Coal Tar ◽  
Loamy Sand ◽  
Clay Loam ◽  
Oxidoreductase Activity ◽  
Sandy Clay Loam ◽  
Sandy Clay ◽  
Polycyclic Aromatic ◽  
Negative Effect

This study used laboratory experiments to compare the effects of coal tar creosote on the activity of oxidoreductive enzymes in sandy loam, loamy sand and sandy clay loam soils. Different amounts of coal tar creosote were added to soil samples as follows: 0 (control), 2, 10 or 50 g kg–1 dry matter. The activity of soil dehydrogenases (DHAs), o-diphenol oxidase (o-DPO), catalase (CAT), nitrate reductase (NR) and peroxidases (POX) was determined. Contamination of soil with coal tar creosote affected oxidoreductase activity. Oxidoreductive enzyme activity following soil contamination with coal tar creosote was in the following order: DHAs &gt; CAT &gt; NR &gt; POX &gt; o-DPO in loamy sand and in sandy loam; and DHAs &gt; POX &gt; CAT &gt; NR &gt; o-DPO in sandy clay loam. The index of soil oxidoreductive activity (IOx) introduced in this study confirms the negative effect of coal tar creosote on oxidoreductase activity in soil. DHAs were the most sensitive to the contamination of soil with coal tar creosote. Moreover, the greatest changes in oxidoreductase activities were observed in loamy sand. Knowledge of the mechanism underlying the effects of coal tar creosote on oxidoreductive processes may enable development of a method for the bioremediation of polycyclic aromatic hydrocarbon-contaminated soils.

Comparison of carbon and nitrogen storage in mineral soils of graminoid and shrub tundra sites, western Greenland

2016 ◽  
Vol 2 (4) ◽  
pp. 165-182 ◽  
Author(s):  
Chelsea L. Petrenko ◽  
Julia Bradley-Cook ◽  
Emily M. Lacroix ◽  
Andrew J. Friedland ◽  
Ross A. Virginia
Keyword(s):  
Vegetation Type ◽  
Mineral Soil ◽  
Biotic Interactions ◽  
The Arctic ◽  
Soil C ◽  
N Storage ◽  
C Storage ◽  
Arctic Soils ◽  
C Pools ◽  
C And N

Shrub species are expanding across the Arctic in response to climate change and biotic interactions. Changes in belowground carbon (C) and nitrogen (N) storage are of global importance because Arctic soils store approximately half of global soil C. We collected 10 (60 cm) soil cores each from graminoid- and shrub-dominated soils in western Greenland and determined soil texture, pH, C and N pools, and C:N ratios by depth for the mineral soil. To investigate the relative chemical stability of soil C between vegetation types, we employed a novel sequential extraction method for measuring organo-mineral C pools of increasing bond strength. We found that (i) mineral soil C and N storage was significantly greater under graminoids than shrubs (29.0 ± 1.8 versus 22.5 ± 3.0 kg·C·m−2 and 1.9 ± .12 versus 1.4 ± 1.9 kg·N·m−2), (ii) chemical mechanisms of C storage in the organo-mineral soil fraction did not differ between graminoid and shrub soils, and (iii) weak adsorption to mineral surfaces accounted for 40%–60% of C storage in organo-mineral fractions — a pool that is relatively sensitive to environmental disturbance. Differences in these C pools suggest that rates of C accumulation and retention differ by vegetation type, which could have implications for predicting future soil C pool storage.

Silvicultural treatments, microclimatic conditions and seedling response in Southern Interior clearcuts

1998 ◽  
Vol 78 (1) ◽  
pp. 115-126 ◽  
Author(s):  
R. L. Fleming ◽  
T. A. Black ◽  
R. S. Adams ◽  
R. J. Stathers
Keyword(s):  
Soil Moisture ◽  
Seedling Establishment ◽  
Initial Period ◽  
Mineral Soil ◽  
Soil Disturbance ◽  
Near Surface ◽  
Lower Elevation ◽  
Organic Horizons ◽  
Soil Temperatures ◽  
Microclimatic Conditions

Post-harvest levels of soil disturbance and vegetation regrowth strongly influence microclimate conditions, and this has important implications for seedling establishment. We examined the effects of blading (scalping), soil loosening (ripping) and vegetation control (herbicide), as well as no soil disturbance, on growing season microclimates and 3-yr seedling response on two grass-dominated clearcuts at different elevations in the Southern Interior of British Columbia. Warmer soil temperatures were obtained by removing surface organic horizons. Ripping produced somewhat higher soil temperatures than scalping at the drier, lower-elevation site, but slightly reduced soil temperatures at the wetter, higher-elevation site. Near-surface air temperatures were more extreme (higher daily maximums and lower daily minimums) over the control than over exposed mineral soil. Root zone soil moisture deficits largely reflected transpiration by competing vegetation; vegetation removal was effective in improving soil moisture availability at the lower elevation site, but unnecessary from this perspective at the higher elevation site. The exposed mineral surfaces self-mulched and conserved soil moisture after an initial period of high evaporation. Ripping and scalping resulted in somewhat lower near-surface available soil water storage capacities. Seedling establishment on both clearcuts was better following treatments which removed vegetation and surface organic horizons and thus enhanced microclimatic conditions, despite reducing nutrient supply. Such treatments may, however, compromise subsequent stand development through negative impacts on site nutrition. Temporal changes in the relative importance of different physical (microclimate) and chemical (soil nutrition) properties to soil processes and plant growth need to be considered when evaluating site productivity. Key words: Microclimate, soil temperature, air temperature, soil moisture, clearcut, seedling establishment

Determination of water content in drying soils: incorporating transition from liquid phase to vapour phase

Soil Research ◽  
2004 ◽  
Vol 42 (1) ◽  
pp. 1 ◽  
Author(s):  
F. Konukcu ◽  
A. Istanbulluoglu ◽  
I. Kocaman
Keyword(s):  
Water Content ◽  
Transition Zone ◽  
Sandy Loam ◽  
Vapour Phase ◽  
Coarse Sand ◽  
Arid Environments ◽  
Evaporation Front ◽  
Matric Potential ◽  
Silty Loam

In arid and semi-arid environments, soil profiles often exhibit a liquid–vapour displacement known as evaporation front characterised by a critical matric potential (ψme) or water content (θe) located somewhere inside the unsaturated zone above a watertable (WT). The objective of this study was to determine the θe including the range of water content (θ) in the transition zone from liquid to vapour both theoretically and experimentally for different soil textures under saline and non-saline WTs. Characteristic shapes of water content and salt concentration profiles were the criteria to obtain θe experimentally, and the θ–diffusivity relationship was used to compute the θe and θ range in the transition zone. Measured θe values of 0.05 and 0.12 m3/m3 under non-saline WT and 0.07 and 0.15 m3/m3 under saline WT were in agreement with the computed values of 0.05 and 0.10 m3/m3 for sandy loam and clay loam soils, respectively. The model calculates roughly the same θe for saline and non-saline conditions. Besides experimental soils, θe and range of θ in the transition zone were calculated for silty loam and coarse sand. The lighter the soil texture, the smaller is θe and the steeper the transition zone. The results were further compared with those calculated by different authors.

scholarly journals Marine substrate response from the analysis of seismic attributes in CHIRP sub-bottom profiles

2017 ◽  
Vol 65 (3) ◽  
pp. 332-345 ◽  
Author(s):  
Larissa Felicidade Werkhauser Demarco ◽  
Antonio Henrique da Fontoura Klein ◽  
Jorge Antonio Guimarães de Souza
Keyword(s):  
Grain Size ◽  
Seismic Reflection ◽  
Ground Truth ◽  
Fine Sand ◽  
Seismic Attributes ◽  
Coarse Sand ◽  
Unconsolidated Sediments ◽  
Shallow Gas ◽  
Size Classes ◽  
Seismic Reflection Profiles

Abstract This paper presents an evaluation of the response of seismic reflection attributes in different types of marine substrate (rock, shallow gas, sediments) using seafloor samples for ground-truth statistical comparisons. The data analyzed include seismic reflection profiles collected using two CHIRP subbottom profilers (Edgetech Model 3100 SB-216S), with frequency ranging between 2 and 16 kHz, and a number (38) of sediment samples collected from the seafloor. The statistical method used to discriminate between different substratum responses was the non-parametric Kruskal-Wallis analysis, carried out in two steps: 1) comparison of Seismic Attributes between different marine substrates (unconsolidated sediments, rock and shallow gas); 2) comparison of Seismic Attributes between different sediment classes in seafloors characterized by unconsolidated sediments (subdivided according to sorting). These analyses suggest that amplitude-related attributes were effective in discriminating between sediment and gassy/rocky substratum, but did not differentiate between rocks and shallow gas. On the other hand, the Instantaneous Frequency attribute was effective in differentiating sediments, rocks and shallow gas, with sediment showing higher frequency range, rock an intermediate range, and shallow gas the lowest response. Regarding grain-size classes and sorting, statistical analysis discriminated between two distinct groups of samples, the SVFS (silt and very fine sand) and the SFMC (fine, medium and coarse sand) groups. Using a Spearman coefficient, it was found that the Instantaneous Amplitude was more efficient in distinguishing between the two groups. None of the attributes was able to distinguish between the closest grain size classes such as those of silt and very fine sand.

scholarly journals Carbon, nitrogen and sulfur (CNS) status and dynamics in Amazon basin upland soils, Brazil

2019 ◽  
Author(s):  
Jörg Matschullat ◽  
Roberval Monteiro Bezerra de Lima ◽  
Sophie F. von Fromm ◽  
Solveig Pospiech ◽  
Andrea M. Ramos ◽  
...  
Keyword(s):  
Climate Change ◽  
Amazon Basin ◽  
Forest Canopy ◽  
Regional Climate ◽  
Mineral Soil ◽  
Regional Climate Change ◽  
Wet Season ◽  
N Losses ◽  
Carbon And Nitrogen ◽  
C And N

Abstract. Given the dimensions of the Amazon basin (7.5 million km2), its internal dynamics, increasing anthropogenic strain on this large biome, and its global role as one of two continental biospheric tipping elements, it appears crucial to have data-based knowledge on carbon and nitrogen concentrations and pools as well as on possible intra-annual dynamics. We quantified carbon (Ct, Corg), nitrogen (N) and sulfur (S) concentrations in litter (ORG) and mineral soil material (TOP 0–20 cm, BOT 30–50 cm) of upland (terra firme) oxisols across Amazonas state and present a first pool calculation. Data are based on triplicate seasonal sampling at 29 sites (forest and post-forest) within the binational project EcoRespira-Amazon (ERA). Repeated sampling increased data accuracy and allows for interpreting intra-annual (seasonal) and climate-change related dynamics. Extreme conditions between the dry season in 2016 and the subsequent wet season (ENSO-related) show differences more clearly. Median CNS in the Amazon basin TOP soils (Ct 1.9, Corg 1.6, N 0.15, S 0.03 wt-% under forest canopy) as well as Corg / N ratios show concentrations similar to European soils (FOREGS, GEMAS). TOP Ct concentrations ranged from 1.02 to 3.29 wt-% (medianForest 2.17 wt-%; medianPost-Forest 1.75 wt-%), N from 0.088 to 0.233 wt-% (medianForest 0.17 wt-%; medianPost-Forest 0.09 wt-%) and S from 0.012 to 0.051 wt.-% (medianForest 0.03 wt.-%; medianPost-Forest 0.02 wt-%). Corg / N ratios ranged from 6 to 14 (median 10). A first pool calculation (hectare-based) illustrates forest versus post-forest changes. The elements are unevenly distributed in the basin with generally higher CNS values in the central part (Amazonas graben) as compared to the southern part of the basin. Deforestation and drought conditions lead to C and N losses – within 50 years after deforestation, C and N losses average 10 to 15 %. Regional climate change with increased drought will likely speed up carbon and nitrogen losses.

The late Wisconsinan olistostrome of the lower Coppermine River valley, Northwest Territories

1986 ◽  
Vol 23 (11) ◽  
pp. 1700-1708 ◽  
Author(s):  
Denis A. St-Onge ◽  
Jean Lajoie
Keyword(s):  
Debris Flows ◽  
Late Quaternary ◽  
Fine Sand ◽  
Coarse Sand ◽  
Coarse Fraction ◽  
River Valley ◽  
Glacial Lake ◽  
The North ◽  
Geologic Record ◽  
Coppermine River

The late Quaternary olistostrome exposed in the lower Coppermine River valley fills a paleovalley that ranges in apparent width from 150 to 400 m and was cut into Precambrian bedrock before the last glaciation. The olistostrome is here named the Sleigh Creek Formation. The coarse fraction of the formation is matrix supported; beds are massive or reversely graded and have sharp, nonerosive contacts. These characteristics suggest deposition of the coarse fraction by debris flows. The olistostrome sequence is bracketed by, and wedged into, a marine rhythmite sequence, which indicates that deposition occurred in a marine environment.About 10 500 years BP glacier ice in the Coronation Gulf lowland dammed the valley to the south, which was occupied by glacial Lake Coppermine. Sediments accumulated in this lake in a 30 m thick, coarsening upward sequence ranging from glaciolacustrine rhythmites of silt and fine sand at the base to coarse sand alluvium, and deltaic gravels at the top. As the Coronation Gulf lowlands became ice free, the Coppermine River reoccupied its former drainage course to the north. The steep south to north gradient and rapid downcutting by the river through the glacial lake sediments produced unstable slope conditions. The resulting debris flows filled a bedrock valley network below the postglacial sea level, forming the diamicton sequence.The interpretation of the Sleigh Creek Formation raises questions concerning silimar diamicton deposits usually defined as "flowtills." More generally, the results of this study indicate that care must be used when attempting paleogeographic reconstructions of "glaciogenic" deposits in marine sequences in any part of the geologic record.

Sign in / Sign up

Export Citation Format

Share Document