A First-Order Fully Cascadable Current-Mode Universal Filter Composed of Dual Output CCIIs and a Grounded Capacitor

2016 ◽  
Vol 25 (05) ◽  
pp. 1650042 ◽  
Author(s):  
Erkan Yuce ◽  
Shahram Minaei
Keyword(s):  
Second Generation ◽  
Current Mode ◽  
Passive Component ◽  
Current Conveyors ◽  
Universal Filter ◽  
First Order ◽  
Low Pass ◽  
In Series ◽  
Component Matching ◽  
High Pass

In this paper, a new first-order current-mode (CM) universal filter employing two dual output second-generation current conveyors (DO-CCIIs), one resistor and a grounded capacitor is proposed. The proposed filter has low input and high output impedances; thus, it can be easily connected with other CM circuits. It can simultaneously realize first-order low-pass (LP) and all-pass (AP) responses and can provide high-pass (HP) response with interconnection of LP and AP responses. It can be tuned electronically by replacing with dual output second-generation current controlled conveyors (DO-CCCIIs) instead of DO-CCIIs and removing the resistor. It has only a resistor but no capacitor connected in series to X terminal of DO-CCII; accordingly, it can be operated at high frequencies. Also, it does not need any critical passive component matching conditions and cancellation constraints. A number of simulation results based on SPICE program are included to exhibit performance, workability and effectiveness of the proposed filter configuration.

CURRENT-MODE ACTIVE-C FILTER EMPLOYING REDUCED NUMBER OF CCCII+s

2007 ◽  
Vol 16 (04) ◽  
pp. 507-516 ◽  
Author(s):  
SHAHRAM MINAEI ◽  
ERKAN YUCE
Keyword(s):  
Current Mode ◽  
Pass Band ◽  
Passive Component ◽  
Resistorless Filter ◽  
Low Pass ◽  
Component Matching ◽  
Band Pass ◽  
High Output Impedance ◽  
Quality Factor Q ◽  
High Pass

In this paper, a universal current-mode second-order active-C filter for simultaneously realizing low-pass, band-pass and high-pass responses is proposed. The presented filter employs only three plus-type second-generation current-controlled conveyors (CCCII+s). This filter needs no critical active and passive component matching conditions and no additional active and passive elements for realizing high output impedance low-pass, band-pass and high-pass characteristics. The angular resonance frequency (ω0) and quality factor (Q) of the proposed resistorless filter can be tuned electronically. To verify the theoretical analysis and to exhibit the performance of the proposed filter, it is simulated with SPICE program.

scholarly journals One-Input Three-Output Current-Mode Universal Filter Using Translinear Current Conveyors

2019 ◽  
Vol 2 (4) ◽  
pp. 101
Author(s):  
Montree Kumngern
Keyword(s):  
Current Mode ◽  
Pass Band ◽  
Current Conveyors ◽  
Current Response ◽  
Universal Filter ◽  
Low Pass ◽  
Band Pass ◽  
Active Matching ◽  
High Output Impedance ◽  
High Pass

This paper presents a new current-mode universal filter with one-input three-output employing three translinear current conveyors and two grounded capacitors. The proposed filter provides low-pass, band-pass, high-pass current response with high output impedance output which can be directly connected for current-mode circuit. The band-pass and all-pass filters can also be obtained. The parameters wo and Q can be controlled separately and electronically by the bias currents of current conveyors. For realizing all filtering functions, no passive and active matching conditions are required. The active and passive sensitivities are low. The characteristic of the proposed circuit can be confirmed by SPICE simulations.

scholarly journals Voltage-Mode Multifunction Biquadratic Filter with One Input and Six Outputs Using Two ICCIIs

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
Hua-Pin Chen
Keyword(s):  
Theoretical Analysis ◽  
Second Generation ◽  
Current Conveyors ◽  
Matching Conditions ◽  
Voltage Mode ◽  
Low Pass ◽  
Biquadratic Filter ◽  
Component Matching ◽  
High Pass

A novel voltage-mode multifunction biquadratic filter with one input and six outputs is presented. The proposed circuit can realize inverting and noninverting low-pass, bandpass, and high-pass filters, simultaneously, by using two inverting second-generation current conveyors (ICCIIs), two grounded capacitors, and four resistors. Moreover, the proposed circuit offers the following attractive advantages: no requirements for component matching conditions, the use of only grounded capacitors, and low active and passive sensitivities. HSPICE and MATLAB simulations results are provided to demonstrate the theoretical analysis.

A New Versatile Universal Biquad Configuration for Emerging Signal Processing Applications

2018 ◽  
Vol 27 (12) ◽  
pp. 1850196 ◽  
Author(s):  
Bhartendu Chaturvedi ◽  
Jitendra Mohan ◽  
Atul Kumar
Keyword(s):  
Second Generation ◽  
Current Mode ◽  
Pass Band ◽  
Current Conveyors ◽  
Fully Differential ◽  
Input Matching ◽  
Low Pass ◽  
Single Input ◽  
Band Pass ◽  
High Pass

The paper introduces a new versatile universal biquadratic configuration based on two fully differential second generation current conveyors without need of input matching conditions. The proposed circuit consists of two fully differential second generation current conveyors, four resistors and two grounded capacitors. The proposed biquad configuration provides all five standard filtering responses: low-pass, high-pass, band-pass, band-reject and all-pass in voltage-mode, transadmittance-mode, current-mode and transimpedance-mode. The proposed circuit is single-input multiple-outputs type, so all responses are available simultaneously. Moreover, extra inverting amplifier and double-type amplifier are also not required in the proposed circuit for any filtering response. The nonideal and parasitic effects of fully differential second generation current conveyor on the proposed circuit have also been investigated. HSPICE simulation results have been incorporated to validate the proposal.

Improved Electronically-Tunable Current-Mode Square-Root-Domain First-Order Multifunction Filter

2021 ◽  
pp. 2150190
Author(s):  
Manoj Kumar Jain
Keyword(s):  
Transient Response ◽  
Current Mode ◽  
Square Root ◽  
Spice Simulation ◽  
First Order ◽  
Low Pass ◽  
Multifunction Filter ◽  
Simulation Results ◽  
Electronically Tunable ◽  
High Pass

Some time back, Kircay reported an electronically-tunable current-mode square-root-domain first-order filter capable of realizing low-pass (LP), high-pass (HP) and all-pass (AP) filter functions. When simulated in SPICE, Kircay’s circuit has been found to exhibit DC offsets in case of LP and AP responses and incorrect transient response in case of HP response. In this paper, an improved circuit overcoming these difficulties/deficiencies has been suggested and its workability of the improved circuit as well as its capability in meeting the intended objectives has been demonstrated by SPICE simulation results.

MULTI-OUTPUT CURRENT FOLLOWER BASED CURRENT-MODE UNIVERSAL FILTER EMPLOYING ONLY GROUNDED CAPACITORS

2014 ◽  
Vol 23 (09) ◽  
pp. 1450123 ◽  
Author(s):  
HALIL ALPASLAN ◽  
ERKAN YUCE
Keyword(s):  
Output Voltage ◽  
Current Mode ◽  
Passive Component ◽  
Theoretical Knowledge ◽  
Universal Filter ◽  
Output Current ◽  
Matching Conditions ◽  
Current Follower ◽  
Component Matching ◽  
High Output

In this paper, a new two-input three-output second-order universal filter is proposed. Two multi-output voltage controlled current followers (MO-VCCFs) and two capacitors are used in the proposed filter. The proposed filter does not have external passive resistors. It has high output impedances yielding easy cascadability. It has the property of electronic tunability. It does not need any critical passive component matching conditions. Also, it is composed of only grounded capacitors; accordingly, it is suitable for integration. Theoretical knowledge is supported via SPICE simulations.

scholarly journals REALIZATION OF FIRST-ORDER CURRENT-MODE FILTERS WITH LOW NUMBER OF MOS TRANSISTORS

2013 ◽  
Vol 22 (01) ◽  
pp. 1250071 ◽  
Author(s):  
ERKAN YUCE ◽  
SHAHRAM MINAEI ◽  
NORBERT HERENCSAR ◽  
JAROSLAV KOTON
Keyword(s):  
Low Voltage ◽  
Current Mode ◽  
Low Noise ◽  
Mos Transistors ◽  
Pass Filter ◽  
First Order ◽  
Saturation Region ◽  
Low Pass ◽  
High Pass ◽  
Nmos Transistors

In this paper, a new current-mode (CM) circuit for realizing all of the first-order filter responses is suggested. The proposed configuration contains low number of components, only two NMOS transistors both operating in saturation region, two capacitors and two resistors. Major advantages of the presented circuit are low voltage, low noise and high linearity. The proposed filter circuit can simultaneously provide both inverting and non-inverting first-order low-pass, high-pass and all-pass filter responses. Computer simulation results achieved through SPICE tool and experimental results are given as examples to demonstrate performance and effectiveness of the proposed topology.

scholarly journals Grounded Impedance Simulator Topologies Employing Minimum Passive Elements

2018 ◽  
Vol 7 (2.28) ◽  
pp. 1 ◽  
Author(s):  
Mohammad Faseehuddin ◽  
Jahariah Sampe ◽  
Sawal Hamid Md Ali
Keyword(s):  
Current Mode ◽  
Cmos Technology ◽  
Passive Component ◽  
Passive Components ◽  
Theoretical Predictions ◽  
Low Pass ◽  
Multifunction Filter ◽  
Component Matching ◽  
Order Butterworth Filter ◽  
Matching Constraints

In this research three new grounded inductance simulators (GIS) are proposed. In addition, frequency dependent negative resistor (FDNR) and grounded capacitor (GC) simulators are also developed. The voltage differencing current conveyor (VDCC) is utilized in the design. All the developed simulator circuits need a single active block and only two grounded passive components. All the designed simulator circuits are perfectly tunable and did not suffer from passive component matching constraints. To demonstrate the performance of the inductor, FDNR and GC circuits they are employed in designing  current mode parallel RLC multifunction filter, low pass third order Butterworth filter and RLC resonance circuits. The VDCC is designed in 0.18μm CMOS technology parameters from TSMC and simulated in P-Spice software to prove the theoretical predictions. 

A New Voltage-Mode Multifunctional Filter Using Only Two Voltage Followers and a Minimum Number of Passive Elements

2015 ◽  
Vol 24 (06) ◽  
pp. 1550085 ◽  
Author(s):  
Firat Yucel ◽  
Erkan Yuce
Keyword(s):  
Experimental Tests ◽  
Passive Component ◽  
High Input ◽  
Voltage Mode ◽  
Low Power Dissipation ◽  
Low Pass ◽  
Minimum Number ◽  
Component Matching ◽  
Matching Constraints ◽  
High Pass

A new voltage-mode (VM) multifunctional filter using only two voltage followers (VFs), two resistors and two capacitors is proposed. The proposed filter with two inputs and two outputs can provide low-pass (LP) and high-pass (HP) responses. It does not need any critical passive component matching constraints. Additionally, it has low output impedances, low power dissipation and adequately low THD values. However, it does not have high input impedances; accordingly, it requires an extra VF to obtain high input impedance. A number of time domain and frequency domain simulations and experimental tests are performed to verify the claimed theory.

scholarly journals The voltage-mode first order universal filter using single voltage differencing differential input buffered amplifier with electronic controllability

2022 ◽  
Vol 12 (2) ◽  
pp. 1308
Author(s):  
Danupat Duangmalai ◽  
Peerawut Suwanjan
Keyword(s):  
Integrated Circuit ◽  
Universal Filter ◽  
Differential Input ◽  
First Order ◽  
Voltage Mode ◽  
Transconductance Amplifier ◽  
Low Pass ◽  
Simulation And Experiment ◽  
Electronically Tunable ◽  
High Pass

In this research contribution, the electronically tunable first-order universal filter employing a single voltage differencing differential input buffered amplifier (VD-DIBA) (constructed from two commercially available integrated circuit (IC): the operational transconductance amplifier, IC number LT1228, and the differential voltage input buffer, IC number AD830), one capacitor and two resistors. The features of the designed first order universal filter are as follows. Three voltage-mode first-order functions, low-pass (LP), all-pass (AP) and high-pass (HP) responses are given. The natural frequency (𝜔0) of the presented configuration can be electronically adjusted by setting the DC bias current. Moreover, the voltage gain of the LP and HP filters can be controllable. The phase responses of an AP configuration can be varied from 00 to −1800 and 1800 to 00. The power supply voltages were set at ±5 𝑉. Verification of the theoretically described performances of the introduced electronically tunable universal filter was proved by the PSpice simulation and experiment.

Sign in / Sign up

Export Citation Format

Share Document