scholarly journals The voltage-mode first order universal filter using single voltage differencing differential input buffered amplifier with electronic controllability

Author(s):  
Danupat Duangmalai ◽  
Peerawut Suwanjan

In this research contribution, the electronically tunable first-order universal filter employing a single voltage differencing differential input buffered amplifier (VD-DIBA) (constructed from two commercially available integrated circuit (IC): the operational transconductance amplifier, IC number LT1228, and the differential voltage input buffer, IC number AD830), one capacitor and two resistors. The features of the designed first order universal filter are as follows. Three voltage-mode first-order functions, low-pass (LP), all-pass (AP) and high-pass (HP) responses are given. The natural frequency (𝜔0) of the presented configuration can be electronically adjusted by setting the DC bias current. Moreover, the voltage gain of the LP and HP filters can be controllable. The phase responses of an AP configuration can be varied from 00 to −1800 and 1800 to 00. The power supply voltages were set at ±5 𝑉. Verification of the theoretically described performances of the introduced electronically tunable universal filter was proved by the PSpice simulation and experiment.

Author(s):  
Rashmika Rai ◽  
◽  
S Indu

The study presents a universal filter and Oscillator obtain by applying only single input. All the passive components used are grounded which is suitable for integrated circuit implementation. In the circuit by applying for single input simultaneously low pass, High Pass, Band Pass, All Pass, and Notch filter is obtained by using two blocks of Differential Difference current conveyor transconductance amplifier.


2019 ◽  
Vol 28 (05) ◽  
pp. 1950078 ◽  
Author(s):  
Montree Kumngern ◽  
Pichai Suksaibul ◽  
Fabian Khateb

This paper presents a new electronically tunable voltage-mode universal filter with four-input one-output employing six simple operational transconductance amplifiers (OTAs), two grounded capacitors and two MOS resistors. The use of grounded passive components is beneficial for integrated circuit implementation. The proposed filter can realize low-pass, band-pass, high-pass, band-stop and all-pass filtering functions without active and passive component-matching conditions and inverting-type input signals requirements. The natural frequency and quality factor can be tuned independently and electronically by adjusting the bias currents. The voltage-mode filter offers the features of high-input impedance and low active and passive sensitivities. The characteristics of the proposed universal filter are verified using PSPICE simulators through 0.35[Formula: see text][Formula: see text]m CMOS process. Experimental results are used to confirm the workability of proposed circuit through LM13600 commercially available OTAs. Also a digitally programmable filter is shown to confirm the advantage of multiple-input universal filter.


2020 ◽  
Vol 41 (3) ◽  
Author(s):  
Tattaya Pukkalanun ◽  
Worapong Tangsrirat ◽  
Natchanai Roongmuanpha

This paper describes the practical realization of electronically adjustable voltage-mode universal filter with three inputs and single output (TISO) using the commercially available integrated circuit (IC)-based voltage differencing buffered amplifiers (VDBAs). The realization is resistor-less and contains only two VDBAs and two capacitors. The described filter structure can realize all the five standard biquadratic filter functions from the same configuration without needing any component matching criterions. It also exhibits low-output impedance, which enables for easy cascading in voltage-mode operation. Owing to practical VDBA realization, the filter circuit can be easily made electronically tunable with orthogonal o-Q tuning. The effects of the VDBA non-idealities on the filter performance have been analyzed in detail. To prove the theoretical finding, the performance of the studied circuit was also experimentally measured using the operational transconductance amplifier


2005 ◽  
Vol 14 (01) ◽  
pp. 159-164 ◽  
Author(s):  
SUDHANSHU MAHESHWARI ◽  
IQBAL A. KHAN

A novel voltage-mode universal filter employing only two current differencing buffered amplifiers (CDBAs) is proposed. The filter uses four inputs and single output to realize six responses, viz. low-pass, high-pass, inverting band-pass, noninverting band-pass, band-elimination, and all-pass through input selection with independent pole-Q control. Computer simulation results using SPICE are also given to verify the theory.


Author(s):  
Manoj Kumar Jain

Some time back, Kircay reported an electronically-tunable current-mode square-root-domain first-order filter capable of realizing low-pass (LP), high-pass (HP) and all-pass (AP) filter functions. When simulated in SPICE, Kircay’s circuit has been found to exhibit DC offsets in case of LP and AP responses and incorrect transient response in case of HP response. In this paper, an improved circuit overcoming these difficulties/deficiencies has been suggested and its workability of the improved circuit as well as its capability in meeting the intended objectives has been demonstrated by SPICE simulation results.


2016 ◽  
Vol 25 (12) ◽  
pp. 1650154 ◽  
Author(s):  
Ahmet Abaci ◽  
Erkan Yuce

In this paper, two new second-order voltage-mode universal filters are proposed. Both of the proposed filters use only two differential voltage current conveyors (DVCCs), four resistors and two grounded capacitors which are advantageous from integrated circuit technology point of view. They can simultaneously provide second-order low-pass, high-pass, band-pass, notch and all-pass responses. They offer orthogonal control of angular resonance frequency and quality factor. However, they have a single matching condition for only all-pass responses. A number of simulations based on SPICE program are accomplished in order to demonstrate the performance of both filters.


2011 ◽  
Vol 20 (03) ◽  
pp. 549-555 ◽  
Author(s):  
A. K. SINGH ◽  
R. SENANI ◽  
D. R. BHASKAR ◽  
R. K. SHARMA

A number of configurations for realizing voltage-mode (VM) biquads using op-amps and OTAs have been presented in the literature, however, none of these provide the following desirable properties simultaneously: (i) realizability of all the five standard filters (namely; low pass, high pass, band pass, band stop and all pass), (ii) tunability of all the three filter parameters (namely; ω0, bandwidth or Q0 and gain) and (iii) not requiring any realization condition in any of the five filter responses. This paper presents a new configuration which does possess all the above mentioned desirable properties simultaneously while using only two internally-compensated type op-amps and a reasonable number of OTAs. The workability of the new configuration has been demonstrated by SPICE simulations based upon CMOS Op-amp and CMOS OTAs.


2013 ◽  
Vol 22 (01) ◽  
pp. 1250064 ◽  
Author(s):  
NEETA PANDEY ◽  
SAJAL K. PAUL

The configuration with electronic tunable characteristics that can work in mixed mode may be useful from IC realization viewpoint and application adaptability. This paper proposes an electronically tunable mixed mode universal filter based on multiple output current controlled current conveyor (MOCCCII) and this single topology without any alteration can be used in all four modes i.e., voltage (VM), current (CM), transimpedance (TIM) and transadmittance (TAM). The architecture uses four MOCCCIIs and two grounded capacitors; and can realize universal filter functions — low pass (LP), band pass (BP), high pass (HP), notch (NF) and all pass (AP) for all four modes. Moreover the input impedance is high and output impedance is low for voltage signal and vice-versa for current signal, hence the proposed topology is suitable for cascading for all four modes. The workability of the proposed circuit has been verified via SPICE simulations using AMS 0.35 μm CMOS technology.


Author(s):  
May Phu Pwint Wai ◽  
Winai Jaikla ◽  
Surapong Siripongdee ◽  
Amornchai Chaichana ◽  
Peerawut Suwanjan

This study aims to design an electronically tunable voltage-mode (VM) universal filter utilizing commercially available LT1228 integrated circuits (ICs) with three-input and single-output (TISO) configuration. With the procedure based on two integrator loop filtering structures, the proposed filter consists of two LT1228s, four resistors, and two grounded capacitors. It realizes five filter output responses: low-pass, all-pass, band-reject, band-pass, and high-pass functions. By selecting input voltage signals, each output responses can be achieved without changing the circuit architecture. The natural angular frequency can be controlled electronically. The input voltage nodes Vin1 and Vin3 possess high impedance. The output node has low impedance, so it can be cascaded to other circuits. The performance of the proposed filter is corroborated by PSpice simulation and hardware implementation which support the theoretical assumptions. The result shows that the range of total harmonic distortion (THD) is lower than 1%, and that the higher the temperature is, the lower the natural angular frequency is.


2012 ◽  
Vol 21 (01) ◽  
pp. 1250013 ◽  
Author(s):  
MEHMET SAGBAS ◽  
MUHAMMET KOKSAL

In this paper, a general electronically tunable resistorless biquad, which realizes current ratio transfer function using current backward transconductance amplifiers is proposed. The biquad contains only two active components and two grounded capacitors, which make it convenient for production by the integrated circuit technology. The proposed biquad realizes all of the basic second order filter characteristics: low pass, high pass, band pass, band reject, and finally all pass. It is convenient for cascading with other similar biquads as well as with any two-port circuit with low impedance input to achieve higher order filter characteristics. The simulations that are performed using PSPICE simulator exhibit satisfactory results coherent with the theory.


Sign in / Sign up

Export Citation Format

Share Document