FRICTION AND WEAR BEHAVIORS OF Ti6Al4V ALLOY TREATED BY PLASMA Ni ALLOYING

2018 ◽  
Vol 25 (05) ◽  
pp. 1850096
Author(s):  
ZHENXIA WANG ◽  
WENLAN CAI ◽  
HAIRUI WU ◽  
NAIMING LIN ◽  
XIAOHONG YAO ◽  
...  
Keyword(s):  
Friction Coefficient ◽  
Wear Mechanism ◽  
Friction And Wear ◽  
Wear Behavior ◽  
Displacement Amplitude ◽  
Ti6al4v Substrate ◽  
Abrasion Wear ◽  
Modified Layer ◽  
Plasma Surface Alloying Technique ◽  
Plasma Surface Alloying

The Ni modified layer was prepared on surface of the Ti6Al4V substrate by plasma surface alloying technique (PSAT). The cross-section micro structure, phase structure and microhardness of Ni modified layer were studied. The friction and wear behavior of the Ni modified layer and the Ti6Al4V substrate were analysed. The effects of displacement amplitude, frequency and fretting time on friction coefficient of the Ni modified layer were investigated. The results indicated that the wear rate was lower compared with that of the Ti6Al4V substrate. Friction coefficient of the Ni modified layer increased with the increase of frequency. But it was insensitive to the change of wear time and the displacement amplitude. The wear mechanism of the Ti6Al4V was adhesion and abrasion wear mechanism while the Ni modified layer showed slightly abrasion wear.

HIGH-TEMPERATURE TRIBOLOGICAL BEHAVIORS OF TiNi/Ti2Ni ALLOYED LAYER ON SURFACE OF Ti6Al4V ALLOY

2017 ◽  
Vol 24 (03) ◽  
pp. 1750028 ◽  
Author(s):  
ZHENXIA WANG ◽  
HAIRUI WU ◽  
NAIMING LIN ◽  
XIAOHONG YAO ◽  
ZHIYONG HE ◽  
...  
Keyword(s):  
High Temperature ◽  
Friction Coefficient ◽  
Friction And Wear ◽  
Room Temperature ◽  
Alloyed Layer ◽  
Surface Alloying ◽  
Wear Performance ◽  
Ti6al4v Substrate ◽  
Oxidation Wear ◽  
Plasma Surface Alloying

Plasma surface alloying (PSA) technique was employed with nickel as incident ions to prepare the TiNi/Ti2Ni alloyed layer on surface of Ti6Al4V. High-temperature friction and wear performance of TiNi/Ti2Ni alloyed layer and the Ti6Al4V substrate were evaluated at 500[Formula: see text]C. The results indicated that the TiNi/Ti2Ni alloyed layer exhibited superior high-temperature wear performance. The variations of friction coefficient were the same rule but wear rate was lower compared to Ti6Al4V substrate. The wear mechanism of TiNi/Ti2Ni alloyed layer was mainly slight abrasion and the Ti6Al4V substrate showed abrasion and oxidation wear. The friction coefficient of the TiNi/Ti2Ni alloyed layer decreased from 0.90 to 0.50 with the increase of temperature from room temperature to 500[Formula: see text]C.

TiN Modified Layer on the 20CrNiMo Steel Surface by Needle–Shape Cathode Glow Plasma Discharging

2011 ◽  
Vol 306-307 ◽  
pp. 553-556
Author(s):  
Fei Chen ◽  
Jia Qing Chen ◽  
Hai Zhou
Keyword(s):  
Friction Coefficient ◽  
High Speed ◽  
Friction And Wear ◽  
Wear Behavior ◽  
Wear Test ◽  
Dry Sliding ◽  
Test Rig ◽  
Modified Layer ◽  
Glow Plasma ◽  
Testing Condition

The structure made of alloying and coating layers of TiN was achieved on the surface of 20CrNiMo steel by the needle-shape cathode glow discharging. It is aimed to reduce the friction coefficient of the 20CrNiMo and to improve the property of the wear-resistance. The morphology of TiN modified layer at cross section was observed by the scanning electron microscope (SEM). The friction and wear behavior of the TiN layer under dry sliding against GCr15 steel was evaluated on a MFT-4000 high speed to-and-fro wear test rig. The results showed that it was feasible to prepare TiN modified layer of 40μm thickness by the needle-shape cathode glow plasma discharging. It has been found that the TiN modified layer has excellent friction and wear-resistant behaviors. The friction coefficient of the 20CrNiMo substrate was about 0.324 under dry sliding, while the TiN modified layer experienced much abated friction coefficient to 0.169 under the same testing condition.

Tribological characterization of all-polymer prosthesis based on multi-directional motion

2021 ◽  
pp. 089270572110286
Author(s):  
Xinyue Zhang ◽  
Dekun Zhang ◽  
Kai Chen ◽  
Handong Xu ◽  
Cunao Feng
Keyword(s):  
Friction Coefficient ◽  
Abrasive Wear ◽  
Wear Mechanism ◽  
Friction And Wear ◽  
Quantitative Relationship ◽  
Motion Path ◽  
Aspect Ratios ◽  
Directional Motion ◽  
Motion Paths ◽  
Prosthesis Material

The complex movement of artificial joints is closely related to the wear mechanism of the prosthesis material, especially for the polymer prosthesis, which is sensitive to motion paths. In this paper, the “soft-soft” all-polymer of XLPE/PEEK are selected to study the influence of motion paths on the friction and wear performance. Based on the periodic characteristics of friction coefficient and wear morphology, this paper reveals the friction and wear mechanism of XLPE/peek under multi-directional motion path, and obtains the quantitative relationship between friction coefficient and the aspect ratios of “∞”-shape motion path, which is of great significance to reveal and analyze the wear mechanism of “soft” all-polymer under multi-directional motion path. The results show that the friction coefficient is affected by the motion paths and have periodicity. Morever, under the multi-directional motion paths, the wear of PEEK are mainly abrasive wear and adhesive wear due to the cross shear effect, while the wear of XLPE is mainly abrasive wear with plastic accumulation. In addition, the friction coefficient is greatly affected the aspect ratios Rs-l of “∞”-shape and loads. Meanwhile, the wear morphologies are greatly affected by the aspect ratios Rs-l of “∞”-shape, but less affected by loads.

Friction and Wear Response of a Hard-Anodized AA6082

2021 ◽  
Vol 1016 ◽  
pp. 1235-1239
Author(s):  
Eleonora Santecchia ◽  
Marcello Cabibbo ◽  
Abdel Magid S. Hamouda ◽  
Farayi Musharavati ◽  
Anton Popelka ◽  
...  
Keyword(s):  
Wear Resistance ◽  
Friction Coefficient ◽  
Scientific Community ◽  
Friction And Wear ◽  
Wear Behavior ◽  
Anodized Aluminum ◽  
Tribological Tests ◽  
Hard Anodizing ◽  
Before And After ◽  
Wear Response

The properties of anodized aluminum, and wear resistance in particular, are of high interest for the scientific community. In this study, discs of AA6082 were subjected to a peculiar hard anodizing process leading to anodized samples having different thicknesses. In order to investigate the wear mechanism of samples, unidirectional tribological tests were performed against alumina balls (corundum) under different loading conditions. Surface and microstructure of all the samples were characterized before and after the tribological tests, using different characterization techniques. The tribological tests showed remarkable differences in the friction coefficient and wear behavior of the anodized AA6082 samples, related to the microstructure modifications and to the specific applied sliding conditions.

The Friction and Wear of Thin, Sintered, Fluoride Films

1972 ◽  
Vol 94 (1) ◽  
pp. 12-18 ◽  
Author(s):  
M. T. Lavik ◽  
B. D. McConnell ◽  
G. David Moore
Keyword(s):  
Friction Coefficient ◽  
Friction And Wear ◽  
Room Temperature ◽  
Wear Behavior ◽  
Strong Dependence ◽  
Aluminum Phosphate ◽  
Friction And Wear Behavior ◽  
Wear Life ◽  
Compositional Changes ◽  
Cure Temperature

Results are presented for the bonding of thin, sintered, fluoride films of BaF2 and CaF2 with mono-aluminum phosphate. Friction and wear behavior of these films has been defined in terms of film compositional changes, film curing procedures, and substrate variations when subjected to varying levels of temperature and load. Mono-aluminum phosphate was found to greatly enhance the adhesion of the sintered fluoride film. There was a strong dependence of wear life at 1000 deg F on the mono-aluminum phosphate content of the film. Films containing 6 vol. percent phosphate appear to be near optimum and exhibited wear lives of 1,000,000 load cycles under sliding conditions in a dual rub-shoe device with friction coefficient levels in the order of 0.10 to 0.20. Near-optimum values were determined for cure temperature (950 deg C), and surface finish (23 μ in. rms) on rhodium-plated substrates. Graphite and gold were added to the aluminum phosphate bonded BaF2: CaF2 films. Both additives were found to lower the friction coefficient at room temperature.

Friction and Wear Behavior of Polypropylene/Montmorillonite Intercalated Nanocomposites

2011 ◽  
Vol 311-313 ◽  
pp. 92-95 ◽  
Author(s):  
Kui Chen ◽  
Tian Yun Zhang ◽  
Wei Wei
Keyword(s):  
Stainless Steel ◽  
Friction Coefficient ◽  
Wear Rate ◽  
Abrasive Wear ◽  
Wear Mechanisms ◽  
Mass Fraction ◽  
Friction And Wear ◽  
Adhesive Wear ◽  
Wear Behavior ◽  
Friction And Wear Behavior

Polypropylene/organo-montmorillonite (PP/OMMT) composites were investigated by XRD. Friction and wear behaviors of this composites sliding against GCr15 stainless steel were examined on M-2000 text rig in a ring-on-block configuration. Worn surfaces of PP and its composites were analyzed by SEM. The result shows that PP macromolecule chains have intercalated into OMMT layers and form intercalated nanocomposites. With the increase of mass fraction of OMMT, both wear rate and friction coefficient of composites first decrease then rise. With the increase of load, from 150 N, 200 N to 250 N, wear rate of composites increases, while friction coefficient reduces. The wear mechanisms of composites are connected with the content of OMMT. Composites were dominated by adhesive wear, abrasive wear and adhesive wear accompanied by abrasive wear respectively with the increase of OMMT content.

Friction and Wear Behavior of Polyetherimide(PEI) Filled With Polytetrafluoroethylene(PTFE)

2010 ◽  
Author(s):  
LiQin Wang ◽  
JianWei Sun ◽  
Le Gu
Keyword(s):  
Friction Coefficient ◽  
Dry Friction ◽  
Friction And Wear ◽  
Wear Behavior ◽  
Surface Hardness ◽  
Tribological Performance ◽  
Friction Condition ◽  
Test Rig ◽  
Friction And Wear Behavior ◽  
Ring Configuration

The tribological performance of Polyetherimide (PEI) composites filled with different Polytetrafluoroethylene (PTFE) content was comparatively evaluated on MM-200 test rig in block-on-ring configuration under dry friction condition. The microstructures of worn surfaces, fractured surfaces and wear mechanisms of the PEI composite were examined under scanning electron microscope (SEM). The variations of elastic modulus and surface hardness with variation in composition were also investigated. The results showed that under conditions of dry friction the PTFE can lower the friction coefficient and reduce wear of the PEI composites. When filled with 10 wt. % PTFE, the composite had the lowest wear rate. For PEI filled with 5wt. % PTFE the friction coefficient was about 0.3 and remained comparatively stable with increase of the PTFE content.

Study on the Friction and Wear Behavior of Grind-Hardened Layer

2010 ◽  
Vol 431-432 ◽  
pp. 385-388 ◽  
Author(s):  
Jian Hua Zhang ◽  
Pei Qi Ge ◽  
Lei Zhang ◽  
Yang Yu ◽  
Hui Li
Keyword(s):  
Friction Coefficient ◽  
Wear Rate ◽  
Wear Debris ◽  
Friction And Wear ◽  
Wear Behavior ◽  
Hardened Layer ◽  
Hardened Steel ◽  
Wear Performance ◽  
Friction And Wear Behavior ◽  
Grind Hardening

The grind-hardening technology utilizes the grinding heat to harden the surface of the workpiece. The friction and wear performance of the grind-hardened layer is one of the important parameters. In this paper, the friction and wear performance of the grind-hardened layer was studied by the friction and wear experiment. The wear rate and the friction coefficient of the grind-hardened steel were studied by comparing with conventional hardened steel and non-hardened steel. The surface worn morphology and the collected wear debris of the grind-hardened steel were observed during the experiment. The wear mechanism of the grind-hardened steel was analyzed under different friction conditions.

Effect of Various Nanoparticles on Friction and Wear Properties of Glass Fiber Reinforced Epoxy Composites

2010 ◽  
Vol 150-151 ◽  
pp. 1106-1109 ◽  
Author(s):  
Yong Kun Wang ◽  
Li Chen ◽  
Zhi Wei Xu
Keyword(s):  
Friction Coefficient ◽  
Wear Rate ◽  
Glass Fiber ◽  
Friction And Wear ◽  
Wear Behavior ◽  
Specific Wear Rate ◽  
Wear Properties ◽  
Nano Tio2 ◽  
Nano Sio2 ◽  
Multi Walled Carbon Nanotubes

The glass fiber (GF) reinforced epoxy (EP) composites filled by nano-Al2O3, nano-TiO2, nano-SiO2 and multi-walled carbon nanotubes (MWCNTs) were prepared. The friction and wear behavior of composites under dry condition were evaluated with block-on-ring friction and wear tester. The morphologies of the worn surfaces of the composites were analyzed by scanning electric microscopy (SEM). The results show that 0.5 wt% MWCNTs and nano-TiO2 can significantly lower the friction coefficient and specific wear rate of composites, respectively, while 0.5 wt% nano-SiO2 and nano-Al2O3 can slightly lower the friction coefficient and specific wear rate of the composites.

scholarly journals Friction and Wear Behavior of Polyimide Composites Reinforced by Surface-Modified Poly-p-Phenylenebenzobisoxazole (PBO) Fibers in High Ambient Temperatures

Polymers ◽  
2019 ◽  
Vol 11 (11) ◽  
pp. 1805
Author(s):  
Yu ◽  
Zhang ◽  
Tang ◽  
Gao
Keyword(s):  
Wear Resistance ◽  
Friction Coefficient ◽  
Wear Rate ◽  
Friction And Wear ◽  
Wear Behavior ◽  
Specific Wear Rate ◽  
Interface Properties ◽  
Sliding Velocity ◽  
Friction And Wear Behavior ◽  
Ambient Temperatures

(1) In order to improve the properties of antifriction and wear resistance of polyimide (PI) composite under high temperature conditions, (2) 3-Aminopropyltriethoxysilane (APTES) and Lanthanum (La) salt modifications were employed to manufacture poly-p-phenylenebenzobisoxazole (PBO)/PI composites with different interface properties. The representative ambient temperatures of 130 and 260 °C were chosen to study the friction and wear behavior of composites with different interface properties. (3) Results revealed that while both modification methods can improve the chemical activity of the surface of PBO fibers, the La salt modification is more effective. The friction coefficient of all composites decreases with the increase of sliding velocity and load at two temperatures, and the specific wear rate is increases. Contrary to the situation in the 130 °C environment, the wear resistance of the unmodified composite in the 260 °C environment is greatly affected by the sliding velocity and load, while the modified composites are less affected. Under the same test parameters, the PBO–La/PI composite has the lowest specific wear rate and friction coefficient, and (4) La salt modification is a more effective approach to improve the properties of antifriction and wear resistance of PI composite than APTES modification in high ambient temperatures.

Sign in / Sign up

Export Citation Format

Share Document