IMPROVEMENT IN HARDNESS AND ELECTROCHEMICAL CORROSION RESISTANCE OF AL-7075 ALLOY BY ARTIFICIAL AGEING

2022 ◽  
Author(s):  
RABIA MUKHTAR ◽  
NAVEED AFZAL ◽  
MOHSIN RAFIQUE ◽  
AMEEQ FAROOQ
Keyword(s):  
Corrosion Resistance ◽  
Electrochemical Corrosion ◽  
Lattice Parameter ◽  
Ageing Temperature ◽  
Aged Alloy ◽  
Artificial Ageing ◽  
Electrochemical Tests ◽  
Al 7075 ◽  
Electrochemical Corrosion Resistance ◽  
7075 Alloy

Artificial ageing of Al-7075 alloy was performed in a muffle furnace at different temperatures ranging from 120∘C to 190∘C for 3[Formula: see text]h. The formation of MgZn2 precipitates in the aged alloy was confirmed through the XRD data. The lattice parameter and crystallite size of aluminum were increased with the increase of the ageing temperature. The scanning electron microscopy results validated the precipitates of different shapes and sizes in the aged samples. The number density of the precipitates was found to be maximum at 170∘C. The Vickers hardness of Al-7075 alloy was increased from 125[Formula: see text]HV to 172[Formula: see text]HV with an increase of the ageing temperature from 120∘C to 170∘C and then decreased at 190∘C. The electrochemical tests of the un-aged and aged samples (in 3.5[Formula: see text]wt.% NaCl solution) showed a decrease in the corrosion rate (0.003[Formula: see text]mm/y) and an increase in the corrosion potential ([Formula: see text]137[Formula: see text]mV) of the alloy upon ageing up to 150∘C, indicating improvement in its corrosion resistance.

Structure and Resistance to Electrochemical Corrosion of NiTi Alloy

2013 ◽  
Vol 203-204 ◽  
pp. 335-338 ◽  
Author(s):  
Bożena Łosiewicz ◽  
Magdalena Popczyk ◽  
Tomasz Goryczka ◽  
Józef Lelątko ◽  
Agnieszka Smołka ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Niti Alloy ◽  
Electrochemical Corrosion ◽  
High Resolution Electron Microscopy ◽  
Potential Method ◽  
Passive Layer ◽  
Open Circuit ◽  
Experimental Conditions ◽  
Electrochemical Tests ◽  
Reflectivity Method

The NiTi alloy (50.6 at.% Ni) passivated for 30 min at 130°C by autoclaving has been studied towards corrosion resistance in aqueous solutions of 3% NaCl, 0.1 M H2SO4, 1 M H2SO4 and HBSS. Structure and thickness of the passive layer (TiO2, rutile) were examined by X-ray reflectivity method and high resolution electron microscopy. Corrosion behavior of this oxide layer was investigated by open circuit potential method and polarization curves. It was found that the corrosion resistance of the passivated NiTi alloy is strongly dependent on the type of corrosive environment. The higher corrosion resistance of the tested samples was revealed in sulfate solutions as compared to chloride ones. The highest resistance to electrochemical corrosion of the NiTi alloy was observed in 0.1 M H2SO4 solution. Susceptibility to pitting corrosion of the tested samples was observed which increased with the concentration rise of chlorine anions in solution. Electrochemical tests for 316L stainless steel carried out under the same experimental conditions revealed a weaker corrosion resistance in all solutions as compared to the highly corrosion resistant NiTi alloy.

scholarly journals Microstructure and Corrosion Resistance of Underwater Laser Cladded Duplex Stainless Steel Coating after Underwater Laser Remelting Processing

Materials ◽  
2021 ◽  
Vol 14 (17) ◽  
pp. 4965
Author(s):  
Congwei Li ◽  
Jialei Zhu ◽  
Zhihai Cai ◽  
Le Mei ◽  
Xiangdong Jiao ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Phase Composition ◽  
Duplex Stainless Steel ◽  
Electrochemical Corrosion ◽  
Chemical Components ◽  
Laser Remelting ◽  
Underwater Environment ◽  
Underwater Laser ◽  
Electrochemical Corrosion Resistance

Combined with the technologies of underwater local dry laser cladding (ULDLC) and underwater local dry laser remelting (ULDLR), a duplex stainless steel (DSS) coating has been made in an underwater environment. The phase composition, microstructure, chemical components and electrochemical corrosion resistance was studied. The results show that after underwater laser remelting, the phase composition of DSS coating remains unchanged and the phase transformation from Widmanstätten austenite + intragranular austenite + (211) ferrite to (110) ferrite occurred. The ULDLR process can improve the corrosion resistance of the underwater local dry laser cladded coating. The corrosion resistance of remelted coating at 3 kW is the best, the corrosion resistance of remelted coating at 1kW and 5kW is similar and the corrosion resistance of (110) ferrite phase is better than grain boundary austenite phase. The ULDLC + ULDLR process can meet the requirements of efficient underwater maintenance, forming quality control and corrosion resistance. It can also be used to repair the surface of S32101 duplex stainless steel in underwater environment.

Effects of mass ratios on salt spray corrosion and electrochemical corrosion behaviors of laser cladded Cr–Ni coatings

2019 ◽  
Vol 66 (3) ◽  
pp. 352-359
Author(s):  
Li Jiahong ◽  
Kong Dejun
Keyword(s):  
Corrosion Resistance ◽  
Laser Cladding ◽  
Salt Spray ◽  
Electrochemical Corrosion ◽  
Corrosion Mechanism ◽  
H13 Steel ◽  
Content Type ◽  
Salt Spray Corrosion ◽  
Electrochemical Tests ◽  
Mass Ratios

Purpose The purpose of this paper is to improve the salt spray corrosion and electrochemical corrosion performances of H13 hot work mould steel, Cr–Ni coatings with the different Cr and Ni mass ratios are fabricated using a laser cladding (LC), which provides an experimental basis for the surface modification treatment of H13 steel. Design/methodology/approach Cr–Ni coatings with the different Cr and Ni mass ratios were firstly fabricated on H13 hot work mould steel using a laser cladding (LC). The salt spray corrosion (SSC) and electrochemical corrosion performances of Cr–Ni coatings in 3.5 Wt.% NaCl solution were investigated to analyze the corrosion mechanism, and the effect of mass ratios of Cr and Ni on their corrosion mechanism was discussed. Findings The laser cladded Cr–Ni coatings with the different Cr and Ni mass ratios are composed of Cr–Ni compounds, which are metallurgically combined with the substrate. The SSC resistance of Cr–Ni coating with the Cr and Ni mass ratios of 24:76 is the highest. The electrochemical corrosion resistance of Cr–Ni coating with the Cr and Ni mass ratio of 24:76 is the best among the three kinds of coatings. Originality/value In this study, the corrosion resistance of laser cladded Cr–Ni coatings with the Cr and Ni mass ratios of 17: 83, 20: 80 and 24: 76 was first evaluated using salt spray corrosion (SSC) and electrochemical tests, and the effect of mass ratios of Cr and Ni on their corrosion mechanism was discussed.

Appraisal on corrosion performances of CrNi, TiAlN/CrNi and CrNi–Al2O3–TiO2 coatings on H13 hot work mold

2020 ◽  
Vol 67 (2) ◽  
pp. 150-157
Author(s):  
Kong Dejun ◽  
Li Jiahong
Keyword(s):  
Corrosion Resistance ◽  
Salt Spray ◽  
Test Chamber ◽  
Electrochemical Corrosion ◽  
Optical Microscope ◽  
Electrochemical Performances ◽  
X Ray Diffraction ◽  
H13 Steel ◽  
Content Type ◽  
Electrochemical Corrosion Resistance

Purpose The purpose of this paper is to evaluate the salt spray corrosion (SSC) and electrochemical corrosion performances of CrNi, TiAlN/NiCr and CrNi–Al2O3–TiO2 coatings on H13 steel, which improved the corrosion resistance of H13 hot work mold. Design/methodology/approach CrNi, TiAlN/NiCr and CrNi–Al2O3–TiO2 coatings were fabricated on H13 hot work mold steel using a laser cladding and cathodic arc ion plating. The SSC and electrochemical performances of obtained coatings were investigated using a corrosion test chamber and electrochemical workstation, respectively. The corrosion morphologies, microstructure and phases were analyzed using an electron scanning microscope, optical microscope and X-ray diffraction, respectively, and the mechanisms of corrosion resistance were also discussed. Findings The CrNi coating is penetrated by corrosion media, producing the oxide of Fe3O4 on the coating surface; and the TiAlN coating is corroded to enter into the CrNi coating, forming the oxides of TiO and NiO, the mechanism is pitting corrosion, whereas the CrNi–Al2O3–TiO2 coating is not penetrated, with no oxides, showing the highest SSC resistance among the three kinds of coatings. The corrosion potential of CrNi coating, TiAlN/CrNi and CrNi–Al2O3–TiO2 coatings was –0.444, –0.481 and –0.334 V, respectively, and the corresponding polarization resistances were 3,074, 2,425 and 86,648 cm2, respectively. The electrochemical corrosion resistance of CrNi–Al2O3–TiO2 coating is the highest, which is enhanced by the additions of Al2O3 and TiO2. Originality/value The CrNi, TiAlN/CrNi and CrNi–Al2O3–TiO2 coatings on H13 hot work mold were firstly evaluated by the SSC and electrochemical performances.

scholarly journals Electrochemical Corrosion Resistance of Ni and Co Bonded Near-Nano and Nanostructured Cemented Carbides

Metals ◽  
2020 ◽  
Vol 10 (2) ◽  
pp. 224 ◽  
Author(s):  
Tamara Aleksandrov Fabijanić ◽  
Marin Kurtela ◽  
Irbas Škrinjarić ◽  
Johannes Pötschke ◽  
Markus Mayer
Keyword(s):  
Mechanical Properties ◽  
Corrosion Resistance ◽  
Grain Growth ◽  
Electrochemical Impedance ◽  
Electrochemical Corrosion ◽  
Common Interest ◽  
Cemented Carbides ◽  
Wear Resistant ◽  
Two Samples ◽  
Electrochemical Corrosion Resistance

The advantages of nanostructured cemented carbides are a uniform, homogenous microstructure and superior, high uniform mechanical properties, which makes them the best choice for wear-resistant applications. Wear-resistant applications in the chemical and petroleum industry, besides mechanical properties, require corrosion resistance of the parts. Co as a binder is not an optimal solution due to selective dissolution in an acidic environment. Thus, the development of cemented carbides with alternative binders to increase the corrosion resistance but still retaining mechanical properties is of common interest. Starting mixtures with WC powder, grain growth inhibitors GGIs; VC and Cr3C2, and an identical binder amount of 11-wt.% were prepared. GGIs were added to retain the size of the starting WC powder in the sintered samples. The parameters of the powder metallurgy process were adapted, and samples have been successfully consolidated. A very fine homogeneous microstructure with relatively uniform grain-size distribution and without microstructural defects in the form of carbide agglomerates and abnormal grain growth was achieved for both Ni-bonded and Co-bonded samples. Achieved mechanical properties, Vickers hardness, and Palmqvist toughness, of Ni-bonded near-nanostructured cemented carbides are slightly lower but still comparable to Co-bonded nanostructured cemented carbides. Two samples of each grade were researched by different electrochemical direct current corrosion techniques. The open circuit potential Ecorr, the linear polarisation resistance (LPR), the Tafel extrapolation method, and the electrochemical impedance spectroscopy (EIS) at room temperature in the solution of 3.5% NaCl. From the carried research, it was found that chemical composition of the binder significantly influenced the electrochemical corrosion resistance. Better corrosion resistance was observed for Ni-bonded samples compared to Co-bonded samples. The corrosion rate of Ni-bonded cemented carbides is approximately four times lower compared to Co-bonded cemented carbides.

Sign in / Sign up

Export Citation Format

Share Document