Direct preparation and microstructure investigation of p-type transparent conducting Ga-doped SnO2 thin films

2010 ◽  
Vol 25 (S1) ◽  
pp. S36-S39 ◽  
Author(s):  
Tieying Yang ◽  
Xiubo Qin ◽  
Huan-hua Wang ◽  
Quanjie Jia ◽  
Runsheng Yu ◽  
...  
Keyword(s):  
Thin Films ◽  
Rf Magnetron Sputtering ◽  
Photoelectron Spectra ◽  
X Ray Diffraction ◽  
X Ray ◽  
Fine Microstructure ◽  
Direct Preparation ◽  
Sno2 Thin Films ◽  
P Type ◽  
Reactive Rf Magnetron Sputtering

Transparent p-type conducting Ga-doped SnO2 thin films were prepared using reactive rf-magnetron sputtering. Good p-type conduction was directly realized without the need of postdeposition annealing. The p-type conductivity was found to be very sensitive to the growth condition and process, suggesting that the carrier behavior is strongly related to the fine microstructure of the films. The microstructures of the films were characterized using synchrotron X-ray diffraction and specular reflectivity techniques. The valence state of the Ga dopant was measured from X-ray photoelectron spectra to explain the origin of net holes presented in the films.

scholarly journals Cu 4O3 thin films deposited by non-reactive rf-magnetron sputtering from a copper oxide target

2021 ◽  
Vol 67 (3 May-Jun) ◽  
pp. 495
Author(s):  
M. A. Cruz Almazán ◽  
E. Vigueras Santiago ◽  
R. López ◽  
S. Hernández López ◽  
V. Hugo Castrejón Sánchez ◽  
...  
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Copper Oxide ◽  
Cuprous Oxide ◽  
Cupric Oxide ◽  
Rf Magnetron Sputtering ◽  
X Ray Diffraction ◽  
Oxide Thin Films ◽  
X Ray ◽  
Reactive Rf Magnetron Sputtering

Copper oxide thin films deposited by sputtering are frequently formed by using metal copper targets in reactive atmospheres. In this report, paramelaconite (Cu4O3) thin films were deposited by non-reactive rf magnetron sputtering. The target used for sputtering was a copper oxide disk fabricated by oxidation of metal copper at 1000 °C for 24 h in airatmosphere. X-ray diffraction (XRD) results showed that the copper oxide target was mainly composed of cupric oxide (CuO) and cuprous oxide (Cu2O) crystals. Raman analyses suggested that the surface of the copper oxide disk is composed by a (CuO) layer. XRD measurements performed to the copper oxide thin films deposited by non-reactive rf magnetron sputtering showed that the film is composed of (Cu4O3) crystals. However,Raman measurements indicated that the Cu4O3 thin films are also composed by amorphous CuO and Cu2O.

Structural and optical properties of Tin Oxide and Indium doped SnO2 thin films deposited by thermal evaporation technique

2016 ◽  
Vol 12 (3) ◽  
pp. 4394-4399
Author(s):  
Sura Ali Noaman ◽  
Rashid Owaid Kadhim ◽  
Saleem Azara Hussain
Keyword(s):  
Thin Films ◽  
Optical Properties ◽  
Tin Oxide ◽  
Thermal Evaporation ◽  
Pure Sno2 ◽  
X Ray Diffraction ◽  
Structural And Optical Properties ◽  
X Ray ◽  
Evaporation Technique ◽  
Sno2 Thin Films

Tin Oxide and Indium doped Tin Oxide (SnO2:In) thin films were deposited on glass and Silicon  substrates  by  thermal evaporation technique.  X-ray diffraction pattern of  pure SnO2 and SnO2:In thin films annealed at 650oC and the results showed  that the structure have tetragonal phase with preferred orientation in (110) plane. AFM studies showed an inhibition of grain growth with increase in indium concentration. SEM studies of pure  SnO2 and  Indium doped tin oxide (SnO2:In) ) thin films showed that the films with regular distribution of particles and they have spherical shape.  Optical properties such as  Transmission , optical band-gap have been measured and calculated.

Properties of Sputter Deposited ZnO Films Co-doped with Lithium and Phosphorus

2013 ◽  
Vol 1494 ◽  
pp. 77-82
Author(s):  
T. N. Oder ◽  
A. Smith ◽  
M. Freeman ◽  
M. McMaster ◽  
B. Cai ◽  
...  
Keyword(s):  
Rf Magnetron Sputtering ◽  
Zno Films ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sapphire Substrates ◽  
Hall Effect Measurements ◽  
Sputter Deposited ◽  
P Type ◽  
Post Deposition ◽  
Co Doped

ABSTRACTThin films of ZnO co-doped with lithium and phosphorus were deposited on sapphire substrates by RF magnetron sputtering. The films were sequentially deposited from ultra pure ZnO and Li3PO4 solid targets. Post deposition annealing was carried using a rapid thermal processor in O2 and N2 at temperatures ranging from 500 °C to 1000 °C for 3 min. Analyses performed using low temperature photoluminescence spectroscopy measurements reveal luminescence peaks at 3.359, 3.306, 3.245 eV for the co-doped samples. The x-ray diffraction 2θ-scans for all the films showed a single peak at about 34.4° with full width at half maximum of about 0.17°. Hall Effect measurements revealed conductivities that change from p-type to n-type over time.

Substrate Temperature and La0.9Sr0.1Ga0.8Mg0.2O3-δ Electrolyte Film Growth by Radio Frequency Magnetron Sputtering

2015 ◽  
Vol 833 ◽  
pp. 127-133
Author(s):  
Jie Yu ◽  
Jie Xing ◽  
Xiu Hua Chen ◽  
Wen Hui Ma ◽  
Rui Li ◽  
...  
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Substrate Temperature ◽  
Radio Frequency ◽  
Film Growth ◽  
Rf Magnetron Sputtering ◽  
X Ray Diffraction ◽  
X Ray ◽  
Electrolyte Film ◽  
Porous Anode

La0.9Sr0.1Ga0.8Mg0.2O3-δ (LSGM) electrolyte thin films were fabricated on La0.7Sr0.3Cr0.5Mn0.5O2.75 (LSCM) porous anode substrates by Radio Frequency (RF) magnetron sputtering method. The compatibility between LSGM and LSCM was examined. Microstructures of LSGM thin films fabricated were observed by scanning electron microscope (SEM). The effect of substrate temperature on LSGM thin films was clarified by X-ray Diffraction (XRD). Deposition rate increases firstly at the range of 50°C~150°C, and then decreases at the range of 150°C ~300°C. After annealing, perovskite structure with the same growth orientation forms at different substrate temperature. Crystallite size decreases at first, to the minimum point at 150°C, then increases as substrate temperature rises.

scholarly journals Structural and Electrochemical Properties of Lithium Nickel Oxide Thin Films

2014 ◽  
Vol 2014 ◽  
pp. 1-5 ◽  
Author(s):  
Gyu-bong Cho ◽  
Tae-hoon Kwon ◽  
Tae-hyun Nam ◽  
Sun-chul Huh ◽  
Byeong-keun Choi ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Electrochemical Properties ◽  
Discharge Capacity ◽  
Oxygen Deficiency ◽  
Oxide Phase ◽  
Rf Magnetron Sputtering ◽  
X Ray Diffraction ◽  
X Ray ◽  
Lithium Nickel Oxide

LiNiO2thin films were fabricated by RF magnetron sputtering. The microstructure of the films was determined by X-ray diffraction and field-emission scanning electron microscopy. The electrochemical properties were investigated with a battery cycler using coin-type half-cells. The LiNiO2thin films annealed below 500°C had the surface carbonate. The results suggest that surface carbonate interrupted the Li intercalation and deintercalation during charge/discharge. Although the annealing process enhanced the crystallization of LiNiO2, the capacity did not increase. When the annealing temperature was increased to 600°C, the FeCrNiO4oxide phase was generated and the discharge capacity decreased due to an oxygen deficiency in the LiNiO2thin film. The ZrO2-coated LiNiO2thin film provided an improved discharge capacity compared to bare LiNiO2thin film suggesting that the improved electrochemical characteristic may be attributed to the inhibition of surface carbonate by ZrO2coating layer.

Formation of p-type Cu3BiS3 absorber thin films by annealing chemically deposited Bi2S3–CuS thin films

1997 ◽  
Vol 12 (3) ◽  
pp. 651-656 ◽  
Author(s):  
P. K. Nair ◽  
L. Huang ◽  
M. T. S. Nair ◽  
Hailin Hu ◽  
E. A. Meyers ◽  
...  
Keyword(s):  
Thin Films ◽  
Visible Region ◽  
Atomic Diffusion ◽  
Optical Coatings ◽  
X Ray Diffraction ◽  
X Ray ◽  
Cell Structures ◽  
Potential Applications ◽  
Xrd Patterns ◽  
P Type

Formation of the ternary compound Cu3BiS3 during annealing of chemically deposited CuS (∼0.3 μm) films on Bi2S3 film (∼0.1 μm on glass substrate) is reported. The interfacial atomic diffusion leading to the formation of the compound during the annealing is indicated in x-ray photoelectron depth profile spectra of the films. The formation of Cu3BiS3 (Wittichenite, JCPDS 9-488) is confirmed by the x-ray diffraction (XRD) patterns. The films are optically absorbing in the entire visible region (absorption coefficient 4 × 104 cm−1 at 2.48 eV or 0.50 μm) and are p-type with electrical conductivity of 102−103 Ω−1 cm−1. Potential applications of these films as optical coatings in the control of solar energy transmittance through glazings and as a p-type absorber film in solar cell structures are indicated.

Highly C-Axis Oriented Barium Titanate Ferroelectric Films Deposited on SrTiO3 Substrate Using an Off-Axis Sputtered Conductive Oxide Layer as Bottom Electrode

2011 ◽  
Vol 399-401 ◽  
pp. 926-929
Author(s):  
Wei Zhang ◽  
Mei Ling Yuan ◽  
Xian Yang Wang ◽  
Jun Ouyang
Keyword(s):  
Thin Films ◽  
Bottom Electrode ◽  
Rf Magnetron Sputtering ◽  
X Ray Diffraction ◽  
Ferroelectric Films ◽  
Axis Orientation ◽  
X Ray ◽  
Pure Argon ◽  
Single Target ◽  
Conductive Oxide

BaTiO3(BTO) thin films were grown on (100) SrTiO3(STO) single crystal substrates using the RF-magnetron sputtering technique (RFMS) in both pure argon and mixed Ar/O2(20% O2) atmosphere. A La0.5Sr0.5CoO3(LSCO) layer was deposited as the bottom electrode by a 90° off-axis single-target RFMS. θ-2θ X-ray diffraction measurements showed that BTO thin films grown in both cases had a highly preferred c-axis orientation (001). From hysteresis measurements, it was confirmed that both films are ferroelectric. The ferroelectric polarizations 2Pr were 6.6 μC/cm2and 27.1 μC/cm2, for the BTO films grown in pure argon and in mixed Ar/O2atmosphere, respectively.

Microstructural and Properties of P-type Nickel Oxide (NiO) Thin Films Deposited by RF Magnetron Sputtering

2018 ◽  
Vol 24 (8) ◽  
pp. 5866-5871 ◽  
Author(s):  
G Balakrishnan ◽  
J. S. Ram Vinoba ◽  
R Rishaban ◽  
S Nathiya ◽  
O. S. Nirmal Ghosh
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Nickel Oxide ◽  
High Mobility ◽  
Rf Magnetron Sputtering ◽  
X Ray Diffraction ◽  
Glass Substrates ◽  
Type Semiconductor ◽  
P Type ◽  
Nio Films

Nickel oxide (NiO) thin films were deposited on glass substrates using the RF magnetron sputtering technique at room temperature. The Argon and oxygen flow rates were kept constant at 10 sccm and 5 sccm respectively. The films were annealed at various temperatures (RT-300 °C) and its influence on the microstructural, optical and electrical properties were investigated. The X-ray diffraction (XRD) investigation of NiO films indicated the polycrystallinity of the films with the (111), (200) and (220) reflections corresponding to the cubic structure of NiO films. The crystallite size of NiO films was in the range ~4–14 nm. The transmittance of the films increased from 20 to 75% with increasing annealed temperature. The optical band gap of the films was 3.6–3.75 eV range for the as-deposited and annealed films. The Hall effect studies indicated the p-type conductivity of films and the film annealed at 300 °C showed higher carrier concentration (N), high conductivity (σ) and high mobility (μ) compared to other films. These NiO films can be used as a P-type semiconductor material in the devices require transparent conducting films.

Reactive Sputtering Growth and Characterizations of InN Thin Films on Si Substrates

2012 ◽  
Vol 545 ◽  
pp. 290-293
Author(s):  
Maryam Amirhoseiny ◽  
Hassan Zainuriah ◽  
Ng Shashiong ◽  
Mohd Anas Ahmad
Keyword(s):  
Thin Films ◽  
Room Temperature ◽  
Rf Magnetron Sputtering ◽  
Rf Power ◽  
X Ray Diffraction ◽  
Nitrogen Gas ◽  
X Ray ◽  
Force Microscopy ◽  
Si Substrates ◽  
Atomic Force

We have studied the effects of deposition conditions on the crystal structure of InN films deposited on Si substrate. InN thin films have been deposited on Si(100) substrates by reactive radio frequency (RF) magnetron sputtering method with pure In target at room temperature. The nitrogen gas pressure, applied RF power and the distance between target and substrate were 2×10-2 Torr, 60 W and 8 cm, respectively. The effects of the Ar–N2 sputtering gas mixture on the structural properties of the films were investigated by using scanning electron microscope, energy-dispersive X-ray spectroscopy, atomic force microscopy and X-ray diffraction techniques.

Sign in / Sign up

Export Citation Format

Share Document