scholarly journals Homogeneous Precipitation Synthesis and Magnetic Properties of Cobalt Ferrite Nanoparticles

2008 ◽  
Vol 2008 ◽  
pp. 1-4 ◽  
Author(s):  
Zhigang Liu ◽  
Xiaodong Li ◽  
Yonghua Leng ◽  
Jingbao Lian ◽  
Shaohong Liu ◽  
...  
Keyword(s):  
Particle Size ◽  
Magnetic Properties ◽  
Cobalt Ferrite ◽  
Ph Value ◽  
Average Particle Size ◽  
Spherical Shape ◽  
Average Particle ◽  
Homogeneous Precipitation ◽  
Transmission Electron ◽  
Reaction Solution

Magnetic nanoparticles (NPs) of cobalt ferrite have been synthesized via a homogeneous precipitation route using hexamethylenetetramine (HMT) as the precipitant. The particle size, crystal structure, and magnetic properties of the synthesized particles were investigated by X-ray diffraction, transmission electron microscopy, and vibrating sample magnetometer. The NPs are of cubic inverse spinel structure and nearly spherical shape. With the increase of oxidation time from 30 to 180 minutes in the reaction solution at90∘C, the average particle size increases from ~30 nm to ~45 nm. The as-synthesized NPs ~30 nm in size show higherMs(61.5 emu/g) and moderate Hc (945 Oe) andMr/Ms(0.45) value compared with the materials synthesized by coprecipitation method using NaOH as precipitate at high pH value.

scholarly journals Experimental Investigation of Chloride Uptake Performances of Hydrocalumite-Like Ca-Al LDHs with Different Microstructures

2020 ◽  
Vol 10 (11) ◽  
pp. 3760
Author(s):  
Shupeng Zhang ◽  
Feng Yu ◽  
Wenting He ◽  
Dapeng Zheng ◽  
Hongzhi Cui ◽  
...  
Keyword(s):  
Particle Size ◽  
Adsorption Capacity ◽  
Ph Value ◽  
Average Particle Size ◽  
Chloride Ion ◽  
Average Particle ◽  
Chloride Uptake ◽  
Reaction Solution ◽  
Interlayer Anion ◽  
Double Hydroxides

In this study, hydrocalumite-like Ca2Al-NO3− layered double hydroxides (Ca-Al LDHs) with different microstructures were synthesized. The crystalline properties, structure composition, morphology and particle size distribution of the Ca-Al LDH (CAL) samples were illustrated. To obtain the chloride uptake performances of CAL, the influences of contact time, initial concentration of Cl−, pH of reaction solution and coexistence anions on the chloride uptake were examined systematically. Compared to the CAL samples obtained at a higher aging temperature, CAL synthesized at 60 °C demonstrated the minimum average particle size (6.148 μm) and the best Cl− adsorption capacity (211.324 mg/g). Based on the test results, the main adsorption mechanism of chloride ion on CAL was recognized as an interlayer anion exchanging reaction other than the dissolution-precipitate mode. With the increase in the pH value of reaction solution from 7 to 13, it was found that the amount of chloride ion adsorbed by CAL increased slightly, and the solution could remain at relatively high pH value even after the adsorption. The presence of CO32− and SO42− reduced the adsorption capacity of CAL dramatically as compared with OH− due to the destruction of layered structure and the formation of precipitates (CaCO3 or CaSO4). The interference sequence of the investigated anions on the chloride uptake of CAL was SO42−, CO32− and OH−, and the order of interlayer anionic affinity was Cl− > OH− > NO3−. The results illustrated that the synthesized CAL could be used as a promising chloride ion adsorbent for the corrosion inhibition of reinforcement embedded cement-based materials.

Microstructure Characterization of Ag Nanoparticles Prepared by Hydrothermal Method

2012 ◽  
Vol 476-478 ◽  
pp. 1138-1141
Author(s):  
Zhi Qiang Wei ◽  
Qiang Wei ◽  
Li Gang Liu ◽  
Hua Yang ◽  
Xiao Juan Wu
Keyword(s):  
Crystal Structure ◽  
Particle Size ◽  
Hydrothermal Method ◽  
Ag Nanoparticles ◽  
Average Particle Size ◽  
Average Particle ◽  
Face Centered Cubic ◽  
Selected Area Electron Diffraction ◽  
Transmission Electron ◽  
Face Centered

Ag nanoparticles were successfully synthesized by hydrothermal method under the polyol system combined with traces of sodium chloride, Silver nitrate(AgNO3) and polyvinylpyrrolidone (PVP) acted as the silver source and dispersant respectively. The samples by this process were characterized via X-ray powder diffraction (XRD), Brunauer–Emmett–Teller (BET) adsorption equation, transmission electron microscopy (TEM) and the corresponding selected area electron diffraction (SAED) to determine the chemical composition, particle size, crystal structure and morphology. The experiment results indicate that the crystal structure of the samples is face centered cubic (FCC) structure as same as the bulk materials, The specific surface area is 24 m2/g, the particle size distribution ranging from10 to 50 nm, with an average particle size about 26 nm obtained by TEM and confirmed by XRD and BET results.

Synthesis and Characterization of Water-Soluble Monolayer-Protected Gold Nanoparticles

2011 ◽  
Vol 415-417 ◽  
pp. 617-620 ◽  
Author(s):  
Yan Su ◽  
Ying Yun Lin ◽  
Yu Li Fu ◽  
Fan Qian ◽  
Xiu Pei Yang ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Particle Size ◽  
Gold Nanoparticles ◽  
Average Particle Size ◽  
Water Soluble ◽  
Synthesis And Characterization ◽  
Average Particle ◽  
Transmission Electron

Water-soluble gold nanoparticles (AuNPs) were prepared using 2-mercapto-4-methyl-5- thiazoleacetic acid (MMTA) as a stabilizing agent and sodium borohydride (NaBH4) as a reducing agent. The AuNPs product was analyzed by transmission electron microscopy (TEM), UV-vis absorption spectroscopy and Fourier transform infrared spectroscopy (FTIR). The TEM image shows that the particles were well-dispersed and their average particle size is about 5 nm. The UV-vis absorption and FTIR spectra confirm that the MMTA-AuNPs was stabilized by the carboxylate ions present on the surface of the AuNPs.

Preparation ZnO nanoparticles with Different Concentration by Laser Ablation in Liquid

2021 ◽  
Vol 39 (1B) ◽  
pp. 197-202
Author(s):  
Ghufran S. Jaber ◽  
Khawla S. Khashan ◽  
Maha J. Abbas
Keyword(s):  
Particle Size ◽  
Laser Ablation ◽  
Laser Pulse ◽  
Laser Energy ◽  
Average Particle Size ◽  
Spherical Shape ◽  
Pulse Number ◽  
Average Particle ◽  
Zno Nps ◽  
Laser Ablation In Liquid

The effects of varying laser pulse numbers on the fabricated of ZnONPs by pulsed laser ablation in deionized water of Zn-metal are investigated. The Nd: YAG laser at energy 600mJ prepared three samples by change the laser pulse number (100, 150, and 200). The results were collected and examined using an electron scanning microscope, XRD – diffraction, and transmission electron microscope. The result revealed the colloidal spherical shape and the homogeneous composition of the ZnO NPs. The nanoparticles resulted in different concentrations and sized distributions by changing the pulse number of a laser. The average particle size and the mass concentration of particle size increase with an increasing number of laser pulses by fixed the laser energy.

scholarly journals Effect of the polymeric coating over Fe3O4 particles used for magnetic separation

2010 ◽  
Vol 8 (5) ◽  
pp. 1041-1046 ◽  
Author(s):  
Raúl Reza ◽  
Carlos Martínez Pérez ◽  
Claudia Rodríguez González ◽  
Humberto Romero ◽  
Perla García Casillas
Keyword(s):  
Particle Size ◽  
Magnetite Nanoparticles ◽  
Average Particle Size ◽  
Spherical Shape ◽  
Polymeric Coating ◽  
Average Particle ◽  
Synthesis Conditions ◽  
Aging Conditions ◽  
Magnetite Particles ◽  
Average Size

AbstractIn this work, the synthesis of magnetite nanoparticles by two variant chemical coprecipitation methods that involve reflux and aging conditions was investigated. The influence of the synthesis conditions on particle size, morphology, magnetic properties and protein adsorption were studied. The synthesized magnetite nanoparticles showed a spherical shape with an average particle size directly influenced by the synthesis technique. Particles of average size 27 nm and 200 nm were obtained. When the coprecipitation method was used without reflux and aging, the smallest particles were obtained. Magnetite nanoparticles obtained from both methods exhibited a superparamagnetic behavior and their saturation magnetization was particle size dependent. Values of 67 and 78 emu g−1 were obtained for the 27 nm and 200 nm magnetite particles, respectively. The nanoparticles were coated with silica, aminosilane, and silica-aminosilane shell. The influence of the coating on protein absorption was studied using Bovine Serum Albumin (BSA) protein.

MICROSTRUCTURE AND MAGNETIC PROPERTIES OF Sm2Fe17NNx−ALLOY- POWDERS AND OF BONDED ANISOTROPIC MAGNETS

1993 ◽  
Vol 07 (01n03) ◽  
pp. 716-720
Author(s):  
B. WALL ◽  
M. KATTER ◽  
W. RODEWALD ◽  
M. VELICESCU
Keyword(s):  
Solid Solution ◽  
Particle Size ◽  
Magnetic Properties ◽  
Average Particle Size ◽  
Average Particle ◽  
Interstitial Solid Solution ◽  
Demagnetization Curve ◽  
Microstructure And Magnetic Properties

In cast Sm2Fe17 ingots minor fractions of SmFe2 and SmFe3 may occur. Nitrogenation of such alloy-powders inidicates that only Sm2Fe17 forms an interstitial solid solution whereas SmFe2 and SmFe3 decompose directly into SmN and α-Fe. From Sm2Fe17Nx alloy powders with an average particle size of about 3 μm anisotropic magnets were prepared by adding 15 wt% Zn-powder. Annealing at 390 ºC results in intrinsic coercivities > 15 kOe promoted by the formation of an unknown binary Fe8Zn92-compound. Whereas annealing at temperatures > 420 ºC leads to the formation of binary Fe3Zn7 and ternary Sm2FeZn2. By the formation of Sm2FeZn2 from Sm2Fe17Nx+Zn some α-Fe occurs inducing a step in the demagnetization curve J(H).

Facile Synthesis and Characterization of Fe-Co Nanoparticles Supported Silica Rice Husk

2016 ◽  
Vol 709 ◽  
pp. 66-69
Author(s):  
Jeyashelly Andas ◽  
Rahmah Atikah Rosdi ◽  
Nur Izzati Mohd Anuar
Keyword(s):  
Particle Size ◽  
Rice Husk ◽  
Sol Gel ◽  
Average Particle Size ◽  
Average Particle ◽  
Silica Source ◽  
Transmission Electron ◽  
Particle Size Analyzer ◽  
Bimetallic Materials ◽  
Co Nanoparticles

A series of Fe-Co nanoparticles were synthesized via sol-gel route at acidic, neutral and basic condition using rice husk as the silica source. The synthesized nanomaterials were designated as Fe-Co3, Fe-Co7 and Fe-Co9 and characterized by Fourier Transform Infrared (FTIR), Transmission Electron Microscope (TEM) and particle size analyzer. The great effect of pH was clearly evidenced from the shifting in the siloxane bond in the FTIR spectrum. TEM investigation confirmed the existence of discrete and almost sphere like nanoparticles. The particle size decreased with an increase in the pH, registering the smallest average particle size at pH 9. In brief, this study promises a fast, rapid and promising method for the conversion of silica rice husk into nanoscale bimetallic materials.

Preparation and Particle Size Characterization of Cu Nanoparticles Prepared by Anodic Arc Plasma

2010 ◽  
Vol 92 ◽  
pp. 163-169
Author(s):  
Hong Xia Qiao ◽  
Zhi Qiang Wei ◽  
Ming Ru Zhou ◽  
Zhong Mao He
Keyword(s):  
Crystal Structure ◽  
Particle Size ◽  
Specific Surface ◽  
Size Distribution ◽  
Surface Area ◽  
Specific Surface Area ◽  
Average Particle Size ◽  
Spherical Shape ◽  
Average Particle ◽  
Uniform Size

Copper nanoparticles were successfully prepared in large scales by means of anodic arc discharging plasma method in inert atmosphere. The particle size, specific surface area, crystal structure and morphology of the samples were characterized by X-ray diffraction (XRD), BET equation, transmission electron microscopy (TEM) and the corresponding selected area electron diffraction (SAED). The experiment results indicate that the crystal structure of the samples is fcc structure as same as that of the bulk materials. The specific surface area is is 11 m2/g, with the particle size distribution ranging from 30 to 90 nm, the average particle size about 67nm obtained from TEM and confirmed from XRD and BET results. The nanoparticles have uniform size, higher purity, narrow size distribution and spherical shape can be prepared by this convenient and effective method.

The Aggregation Study and Characterization of Silver Nanoparticles

2017 ◽  
Vol 263 ◽  
pp. 165-169
Author(s):  
Silvia Chowdhury ◽  
Faridah Yusof ◽  
Nadzril Sulaiman ◽  
Mohammad Omer Faruck
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Particle Size ◽  
Silver Nanoparticles ◽  
Absorption Spectrum ◽  
Average Particle Size ◽  
Average Particle ◽  
Transmission Electron ◽  
Vis Spectroscopy

In this article, we have studied the process of silver nanoparticles (AgNPs) aggregation and to stop aggregation 0.3% Polyvinylpyrrolidone (PVP) was used. Aggregation study carried out via UV-vis spectroscopy and it is reported that the absorption spectrum of spherical silver nanoparticles were found a maximum peak at 420 nm wavelength. Furthermore, Transmission Electron Microscopy (TEM) were used to characterized the size and shape of AgNPs, where the average particle size is around 10 to 25 nm in diameter and the AgNPs shape is spherical. Next, Dynamic Light Scattering (DLS) were used, owing to observed size distribution and self-correlation of AgNPs.

Frequency dependence and fuel effect on optical properties of nano TiO2-based structures

2016 ◽  
Vol 30 (18) ◽  
pp. 1650247 ◽  
Author(s):  
Mahdi Ghasemifard ◽  
Misagh Ghamari ◽  
Meysam Iziy
Keyword(s):  
Particle Size ◽  
Optical Properties ◽  
Average Particle Size ◽  
Combustion Method ◽  
Average Particle ◽  
X Ray Diffraction ◽  
Nano Tio2 ◽  
Transmission Electron ◽  
Auto Combustion ◽  
Xrd Patterns

TiO2-(Ti[Formula: see text]Si[Formula: see text]O2 nanopowders (TS-NPs) with average particle size around 90 nm were successfully synthesized by controlled auto-combustion method by using citric acid/nitric acid (AC:NA) and urea/metal cation (U:MC). The structure of powders was studied based on their X-ray diffraction (XRD) patterns. The XRD of TS-NPs shows that rutile and anatase are the main phases of TS-NPs for AC:NA and U:MC, respectively. Particle size and histogram of nanopowders were characterized by transmission electron microscopy (TEM) and dynamic light scattering (DLS). Optical properties of TS-NPs were calculated by Fourier transform infrared spectroscopy (FTIR) and Kramers–Kroning (KK) relation. Plasma frequencies of TS-NPs obtained from energy loss functions depend on fuels as a result of changes in crystal structure, particle size distribution, and morphology.

Sign in / Sign up

Export Citation Format

Share Document