scholarly journals Magnesium Borate Synthesis by Microwave Energy: A New Method

2013 ◽  
Vol 2013 ◽  
pp. 1-6 ◽  
Author(s):  
Azmi Seyhun Kipcak ◽  
Emek Moroydor Derun ◽  
Sabriye Piskin
Keyword(s):  
Reaction Times ◽  
High Heat ◽  
New Method ◽  
X Ray Diffraction ◽  
Magnesium Borate ◽  
X Ray ◽  
Boron Minerals ◽  
Ft Ir ◽  
Borate Minerals

Magnesium borates are one of the major groups of boron minerals that have important properties such as high heat and corrosion resistances and high coefficients of elasticity. In this study, magnesium borate minerals are synthesized using boric acid and magnesium oxide with a new method of microwave, and the synthesized minerals are characterized by various analysis techniques. The results show that pure, “magnesium borate hydrate” minerals are obtained at the end of various steps. The characterization of the products is determined with the techniques of X-Ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FT-IR), Raman Spectroscopy, and Scanning Electron Microscopy (SEM). Additionally, overall “magnesium borate hydrate” yields are calculated and found about 67% at 270 W, 8 minutes and 360 W, 3 minutes of reaction times, respectively.

scholarly journals Rapid four-component synthesis of dihydropyrano[2,3-c]pyrazoles using nano-eggshell/Ti(IV) as a highly compatible natural based catalyst

BMC Chemistry ◽  
2021 ◽  
Vol 15 (1) ◽  
Author(s):  
Arefeh Dehghani Tafti ◽  
Bi Bi Fatemeh Mirjalili ◽  
Abdolhamid Bamoniri ◽  
Naeimeh Salehi
Keyword(s):  
Thermo Gravimetric Analysis ◽  
Reaction Times ◽  
Diffraction Field ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Solvent Free Conditions ◽  
High Yields ◽  
Work Up

AbstractNano-eggshell/Ti(IV) as a novel naturally based catalyst was prepared, characterized and applied for the synthesis of dihydropyrano[2,3-c]pyrazole derivatives. The characterization of nano-eggshell/Ti(IV) was performed using Fourier Transform Infrared spectroscopy, X-ray Diffraction, Field Emission Scanning Electron Microscopy, Energy-Dispersive X-ray Spectroscopy, and Thermo Gravimetric Analysis. Dihydropyrano[2,3-c]pyrazoles were synthesized in the presence of nano-eggshell/Ti(IV) via a four component reaction of aldehydes, ethyl acetoacetate, malononitrile and hydrazine hydrate at room temperature under solvent free conditions. The principal affairs of this procedure are mild condition, short reaction times, easy work-up, high yields, reusability of the catalyst and the absence of toxic organic solvents.

One Step Synthesis and Characterization of Zirconia-Graphene Composites

2012 ◽  
Vol 600 ◽  
pp. 174-177 ◽  
Author(s):  
Jian Fei Xia ◽  
Zong Hua Wang ◽  
Yan Zhi Xia ◽  
Fei Fei Zhang ◽  
Fu Qiang Zhu ◽  
...  
Keyword(s):  
Synthesis And Characterization ◽  
Two Dimensional ◽  
X Ray Diffraction ◽  
X Ray ◽  
Graphene Composite ◽  
Transmission Electron ◽  
One Step ◽  
Ft Ir ◽  
Xrd Techniques

Zirconia-graphene composite (ZrO2-G) has been successfully synthesized via decomposition of ZrOCl2•6H2O in a water-isopropanol system with dispersed graphene oxide (GO) utilizing Na2S as a precursor could enable the occurrence of the deposition of Zr4+ and the deoxygenation of GO at the same time. Transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FT-IR) and X-ray diffraction (XRD) techniques were used to characterize the samples. It was found that graphene were fully coated with ZrO2, and the ZrO2 existing in tetragonal phase, which resulted in the formation of two-dimensional composite.

Microwave-assisted solvent-free synthesis and spectral and structural characterization of cyclotriphosphazene hexakis(o-tolylamide)

2018 ◽  
Vol 73 (12) ◽  
pp. 999-1003 ◽  
Author(s):  
Mohammad Hakimi ◽  
Homeyra Rezaei ◽  
Keyvan Moeini ◽  
Heidar Raissi ◽  
Vaclav Eigner ◽  
...  
Keyword(s):  
Nmr Spectroscopy ◽  
Microwave Irradiation ◽  
Stacking Interactions ◽  
X Ray Diffraction ◽  
Aromatic Rings ◽  
X Ray ◽  
Microwave Assisted ◽  
Ft Ir ◽  
Solvent Free Synthesis

AbstractA new cyclotriphosphazene, 2,2,4,4,6,6-hexakis (o-tolylamono)-1,3,5,2λ5,4λ5,6λ5-triazatriphosphinine (MPAP), was prepared using microwave irradiation and identified by elemental analysis, FT-IR, Raman, 31P NMR spectroscopy, and single-crystal X-ray diffraction. In the crystal, in addition to hydrogen bonds, the network is further stabilized by inter- and intramolecular π–π stacking interactions between aromatic rings.

scholarly journals Synthesis of new bimetallic phosphate (Al/Ag3PO4) and study for its Catalytic performance in the synthesis of 1,2-dihydro-l-phenyl-3H-naphth [1,2-e]-[1,3] oxazin-3-one derivatives

2021 ◽  
Vol 11 (3) ◽  
pp. 215
Author(s):  
Achraf El Hallaoui ◽  
Tourya Ghailane ◽  
Soukaina Chehab ◽  
Youssef Merroun ◽  
Rachida Ghailane ◽  
...  
Keyword(s):  
Reaction Times ◽  
Catalytic Performance ◽  
X Ray Diffraction ◽  
One Pot ◽  
X Ray ◽  
Silver Sulfate ◽  
Triple Super Phosphate ◽  
Aryl Aldehyde ◽  
Ft Ir ◽  
First Time

<p>This work aims to prepare a new bimetallic phosphate catalyst using a new simple and effective method. This new catalyst was ready for the first time by a modification of Triple Super Phosphate (TSP) fertilizer with silver sulfate (AgSO<sub>4</sub>), followed by the impregnation of the aluminum atoms using aluminum nitrate (Al(NO<sub>3</sub>)<sub>3</sub>). The use of Al/Ag<sub>3</sub>PO<sub>4</sub>, for the first time as a heterogeneous catalyst in organic chemistry, offers a new, efficient, and green pathway for synthesizing 1,2-dihydro-l-phenyl-3H-naphth[1,2-e]-[1,3]oxazin-3-one derivatives by one-pot three-component cyclocondensation of b-naphthol, aryl aldehyde, and urea. The structure and the morphology of the prepared catalyst were characterized by spectroscopic methods such as X-Ray Diffraction (XRD), Fourier Transform Infrared spectroscopy (FT-IR), and dispersive X-ray spectrometry coupled with a scanning electron microscope (EDX-SEM). In addition, the optimization of the reaction parameters was carried out considering the effect of catalyst amount, the temperature, and the solvent. The procedure described herein allowed a comfortable preparation of oxazine derivatives with excellent yields, short reaction times, and in the absence of organic solvent.</p>

The Characterization of Bovine Bone-Derived Hydroxyapatite Isolated Using Novel Non-Hazardous Method

2020 ◽  
Vol 45 ◽  
pp. 49-56
Author(s):  
Aniek Setiya Budiatin ◽  
Samirah ◽  
Maria Apriliani Gani ◽  
Wenny Putri Nilamsari ◽  
Chrismawan Ardianto ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Extraction Method ◽  
Bovine Bone ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ft Ir ◽  
Novel Method ◽  
Scanning Electron

Bovine bone is a considerable source for the production of hydroxyapatite. The recent study reported a novel method to extract hydroxyapatite from bovine bone without producing hazardous residue. The bovine bones were cut and boiled in the opened chamber followed by boiling in pressurized tank. The bones were then soaked into 95% ethanol. Calcination was then conducted in 800°C, 900°C and 1,000°C, for 2 hours. The result was then grinded and sieved. The powder then was characterized using Fourier transform infrared (FT-IR), Scanning electron microscopy (SEM) and X-ray diffraction analysis (XRD) to measure the purity of hydroxyapatite. It is concluded that the hydroxyapatite derived from this process showed 100% purity, resulting 35.34 ± 0.39% w/w from the wet bone weight and 72.3% w/w from the dried weight. The present extraction method has been proven to yield high amount of pure hydroxyapatite as well as reducing the use of hazardous reagent.

scholarly journals Synthesis, Crystal Structures, and Spectroscopic Characterization of Bis-aldehyde Monomers and Their Electrically Conductive Pristine Polyazomethines

Polymers ◽  
2019 ◽  
Vol 11 (9) ◽  
pp. 1498 ◽  
Author(s):  
Abdul Hafeez ◽  
Zareen Akhter ◽  
John F. Gallagher ◽  
Nawazish Ali Khan ◽  
Asghari Gul ◽  
...  
Keyword(s):  
Electrical Conductivity ◽  
Spectroscopic Characterization ◽  
Spectroscopic Techniques ◽  
Conductivity Measurements ◽  
X Ray Diffraction ◽  
Electrically Conductive ◽  
X Ray ◽  
Vis Spectroscopy ◽  
Ft Ir

Bis-aldehyde monomers 4-(4′-formyl-phenoxy)benzaldehyde (3a), 3-methoxy-4-(4′-formyl-phenoxy)benzaldehyde (3b), and 3-ethoxy-4-(4′-formyl-phenoxy)benzaldehyde (3c) were synthesized by etherification of 4-fluorobenzaldehyde (1) with 4-hydroxybenzaldehyde (2a), 3-methoxy-4-hydroxybenzaldehyde (2b), and 3-ethoxy-4-hydroxybenzaldehyde (2c), respectively. Each monomer was polymerized with p-phenylenediamine and 4,4′-diaminodiphenyl ether to yield six poly(azomethine)s. Single crystal X-ray diffraction structures of 3b and 3c were determined. The structural characterization of the monomers and poly(azomethine)s was performed by FT-IR and NMR spectroscopic techniques and elemental analysis. Physicochemical properties of polymers were investigated by powder X-ray diffraction, thermogravimetric analysis (TGA), viscometry, UV–vis, spectroscopy and photoluminescence. These polymers were subjected to electrical conductivity measurements by the four-probe method, and their conductivities were found to be in the range 4.0 × 10−5 to 6.4 × 10−5 Scm−1, which was significantly higher than the values reported so far.

Characterization of Electrospun Poly(Lactic Acid)/polyaniline Blend Nanofibers

2011 ◽  
Vol 332-334 ◽  
pp. 317-320 ◽  
Author(s):  
Hui Qin Zhang
Keyword(s):  
Lactic Acid ◽  
Composite Nanofibers ◽  
Weight Ratio ◽  
Electrospinning Process ◽  
Poly Lactic Acid ◽  
X Ray Diffraction ◽  
Sem Images ◽  
X Ray ◽  
Ft Ir

In this study, composite nanofibers of polyaniline doped with dodecylbenzene sulfonic acid (PANI-DBSA) and Poly(lactic acid) (PLA) were prepared via an electrospinning process. The surface morphology, thermal properties and crystal structure of PLA/PANI-DBSA nanofibers are characterized using Fourier transform infrared spectroscopy (FT-IR), wide-angle x-ray diffraction (WAXD) and scanning electron microscopy (SEM). SEM images showed that the morphology and diameter of the nanofibers were affected by the weight ratio of blend solution.

Preparation and Electrical Characterization of Poly(Aniline) NanoClay Composites

2015 ◽  
Vol 34 (4) ◽  
Author(s):  
Esma Ahlatcioǧlu ◽  
Bahire Filiz şenkal ◽  
Mustafa Okutan
Keyword(s):  
Electrical Characterization ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
Inorganic Hybrid ◽  
X Ray ◽  
Ft Ir ◽  
Doped Polyaniline ◽  
Poly Aniline ◽  
Scanning Electron

AbstractIn this work, synthesis and characterization of composite materials based on NanoClay(NC) and boric acid doped PolyAniline (PANI) is studied. PANI was successfully incorporated into NC to form PANI-NC composites. The resulting organic-inorganic hybrid material, PANI-NC was characterized by various physicochemical techniques. Formation of PANI inside the clay tactoid has been confirmed by X-ray diffraction studies (XRD), scanning electron microscope (SEM) and FT-IR. Also, conductivity and physical properties of the PANI-NC composites were investigated.

Preparation and Characterization of Supported H3PW12O40 and Supported Cesium-Substituted Dodecatungstophosphate

2012 ◽  
Vol 509 ◽  
pp. 321-327 ◽  
Author(s):  
Zi Li Liu ◽  
Cui Xia Xu ◽  
Qian Wen Dai ◽  
Chao Xiang ◽  
Jian Jie Zhang
Keyword(s):  
Solid Acid ◽  
Solid Acid Catalysts ◽  
Incipient Wetness Impregnation ◽  
Acid Catalysts ◽  
X Ray Diffraction ◽  
X Ray ◽  
Highly Dispersed ◽  
Probe Experiment ◽  
Ft Ir

Supported H3PW12O40 (HPW) and supported Cesium-Substituted dodecatungsto-phosphate are eco-friendly solid acid catalysts. A series of different loading H3PW12O40/SiO2 and HPW/diatomite were prepared by a typical incipient wetness impregnation of methanol, meanwhile SiO2 and diatomite supported Cs-salt catalysts were prepared via two-step impregnating method. The catalysts were investigated by X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FT-IR). The results indicate that the Keggin structure of HPW is intact in the SiO2-supported HPW and SiO2-supported CsHPW. HPW and CsHPW are highly dispersed in the SiO2 at the low loading, while the loading is more than 40% the catalyst grains increase and gather on the surface of the carrier. What's more, diatomite is not a suitable support. HPW and CsHPW have better distribution in the SiO2 than in the diatomite. The activity of catalyst was tested in probe experiment of the alkylation of thiopene (TH) with 1-hexene.

scholarly journals Growth and Characterization of Pure and Doped L-Alanine Tartrate Single Crystals

2013 ◽  
Vol 2013 ◽  
pp. 1-5 ◽  
Author(s):  
K. Rajesh ◽  
B. Milton Boaz ◽  
P. Praveen Kumar
Keyword(s):  
Single Crystals ◽  
Vickers Microhardness ◽  
Diffraction Method ◽  
Dielectric Studies ◽  
X Ray Diffraction ◽  
X Ray ◽  
Cell Parameters ◽  
Ft Ir ◽  
Ft Ir Spectroscopy

Single crystals of pure and Lanthanum doped L-Alanine Tartrate were grown by slow evaporation method. The cell parameters were determined using single crystal X-ray diffraction method. To improve the physical properties of the LAT crystal, Lanthanum dopant was added by 2 mol%. ICP studies confirm the presence of Lanthanum in the grown LAT crystal. Transparency range of the crystal was determined using UV-VIS-NIR spectrophotometer. The functional groups of pure and doped LAT crystals were analyzed by FT-IR spectroscopy. Using Vickers microhardness tester, mechanical strength of the material was found. Dielectric studies of pure and doped LAT single crystals were carried out. The doped LAT crystal is found to have efficiency higher than that of pure LAT crystal.

Sign in / Sign up

Export Citation Format

Share Document