scholarly journals Design and Optimization of a Low Power Pressure Sensor for Wireless Biomedical Applications

2015 ◽  
Vol 2015 ◽  
pp. 1-13 ◽  
Author(s):  
J. Sosa ◽  
Juan A. Montiel-Nelson ◽  
R. Pulido ◽  
Jose C. Garcia-Montesdeoca
Keyword(s):  
Blood Pressure ◽  
Power Consumption ◽  
Low Power ◽  
Pressure Sensor ◽  
Biomedical Applications ◽  
Pressure Sensors ◽  
High Sensitivity ◽  
Cmos Technology ◽  
Low Noise ◽  
Least Significant Bit

A blood pressure sensor suitable for wireless biomedical applications is designed and optimized. State-of-the-art blood pressure sensors based on piezoresistive transducers in a full Wheatstone bridge configuration use low ohmic values because of relatively high sensitivity and low noise approach resulting in high power consumption. In this paper, the piezoresistance values are increased in order to reduce by one order of magnitude the power consumption in comparison with literature approaches. The microelectromechanical system (MEMS) pressure sensor, the mixed signal circuits signal conditioning circuitry, and the successive approximation register (SAR) analog-to-digital converter (ADC) are designed, optimized, and integrated in the same substrate using a commercial 1 μm CMOS technology. As result of the optimization, we obtained a digital sensor with high sensitivity, low noise (0.002 μV/Hz), and low power consumption (358 μW). Finally, the piezoresistance noise does not affect the pressure sensor application since its value is lower than half least significant bit (LSB) of the ADC.

CMOS-MEMS Based Current Mirror MOSFET Embedded Pressure Sensor for Healthcare and Biomedical Applications

2013 ◽  
Vol 647 ◽  
pp. 315-320 ◽  
Author(s):  
Pradeep Kumar Rathore ◽  
Brishbhan Singh Panwar
Keyword(s):  
Pressure Sensor ◽  
Biomedical Applications ◽  
Circuit Simulation ◽  
Applied Pressure ◽  
Pressure Sensors ◽  
Cmos Technology ◽  
Current Mirror ◽  
Sensing Element ◽  
Pressure Sensing ◽  
Cmos Mems

This paper reports on the design and optimization of current mirror MOSFET embedded pressure sensor. A current mirror circuit with an output current of 1 mA integrated with a pressure sensing n-channel MOSFET has been designed using standard 5 µm CMOS technology. The channel region of the pressure sensing MOSFET forms the flexible diaphragm as well as the strain sensing element. The piezoresistive effect in MOSFET has been exploited for the calculation of strain induced carrier mobility variation. The output transistor of the current mirror forms the active pressure sensing MOSFET which produces a change in its drain current as a result of altered channel mobility under externally applied pressure. COMSOL Multiphysics is utilized for the simulation of pressure sensing structure and Tspice is employed to evaluate the characteristics of the current mirror pressure sensing circuit. Simulation results show that the pressure sensor has a sensitivity of 10.01 mV/MPa. The sensing structure has been optimized through simulation for enhancing the sensor sensitivity to 276.65 mV/MPa. These CMOS-MEMS based pressure sensors integrated with signal processing circuitry on the same chip can be used for healthcare and biomedical applications.

scholarly journals A 60 GHz fully differential LNA in 90 nm CMOS technology

2013 ◽  
Vol 6 (2) ◽  
pp. 109-113 ◽  
Author(s):  
Andrea Malignaggi ◽  
Amin Hamidian ◽  
Georg Boeck
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Transmission Lines ◽  
Noise Figure ◽  
Design Procedure ◽  
Cmos Technology ◽  
High Gain ◽  
Low Noise ◽  
60 Ghz ◽  
Fully Differential

The present paper presents a fully differential 60 GHz four stages low-noise amplifier for wireless applications. The amplifier has been optimized for low-noise, high-gain, and low-power consumption, and implemented in a 90 nm low-power CMOS technology. Matching and common-mode rejection networks have been realized using shielded coplanar transmission lines. The amplifier achieves a peak small-signal gain of 21.3 dB and an average noise figure of 5.4 dB along with power consumption of 30 mW and occupying only 0.38 mm2pads included. The detailed design procedure and the achieved measurement results are presented in this work.

Ultrahigh Sensitivity Micro-cliff Graphene Wearable Pressure Sensor Made by Instant Flash Light Exposure

Nanoscale ◽  
2021 ◽  
Author(s):  
Yachu Zhang ◽  
Han Lin ◽  
Fei Meng ◽  
Huai Liu ◽  
David Mesa ◽  
...  
Keyword(s):  
Health Monitoring ◽  
Pressure Sensor ◽  
Biomedical Applications ◽  
Light Exposure ◽  
Pressure Sensors ◽  
High Sensitivity ◽  
Fast Response ◽  
Highly Sensitive ◽  
Ultrahigh Sensitivity ◽  
Sensitive Pressure

Wearable and highly sensitive pressure sensors are of great importance for robotics, health monitoring and biomedical applications. Simultaneously achieving high sensitivity within a broad working range, fast response time (within...

scholarly journals Design of a very low-power, low-cost 60 GHz receiver front-end implemented in 65 nm CMOS technology

2011 ◽  
Vol 3 (2) ◽  
pp. 131-138 ◽  
Author(s):  
Michael Kraemer ◽  
Daniela Dragomirescu ◽  
Robert Plana
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Noise Figure ◽  
Low Cost ◽  
Cmos Technology ◽  
Low Noise ◽  
Oxide Semiconductor ◽  
Voltage Controlled Oscillator ◽  
60 Ghz ◽  
Front End

The research on the design of receiver front-ends for very high data-rate communication in the 60 GHz band in nanoscale Complementary Metal Oxide Semiconductor (CMOS) technologies is going on for some time now. Although a multitude of 60 GHz front-ends have been published in recent years, they are not consequently optimized for low power consumption. Thus, these front-ends dissipate too much power for battery-powered applications like handheld devices, mobile phones, and wireless sensor networks. This article describes the design of a direct conversion receiver front-end that addresses the issue of power consumption, while at the same time permitting low cost (due to area minimization by the use of spiral inductors). It is implemented in a 65 nm CMOS technology. The realized front-end achieves a record power consumption of only 43 mW including low-noise amplifier (LNA), mixer, a voltage controlled oscillator (VCO), a local oscillator (LO) buffer, and a baseband buffer (without this latter buffer the power consumption is even lower, only 29 mW). Its pad-limited size is 0.55 × 1 mm2. At the same time, the front-end achieves state-of-the-art performance with respect to its other properties: Its maximum measured power conversion gain is 30 dB, the RF and IF bandwidths are 56.5–61.5 and 0–1.5 GHz, respectively, its measured minimum noise figure is 9.2 dB, and its measured IP−1 dB is −36 dBm.

Design, Fabrication and Characterization of Ultra Miniature Piezoresistive Pressure Sensors for Medical Implants

2011 ◽  
Vol 254 ◽  
pp. 94-98 ◽  
Author(s):  
Li Shiah Lim ◽  
Woo Tae Park ◽  
Liang Lou ◽  
Han Hua Feng ◽  
Pushpapraj Singh
Keyword(s):  
Pressure Sensor ◽  
Biomedical Applications ◽  
Low Cost ◽  
Silicon Nanowire ◽  
Pressure Sensors ◽  
High Sensitivity ◽  
Medical Implants ◽  
Mems Technology ◽  
Piezoresistive Pressure Sensors

Pressure sensors using MEMS technology have been advanced due to their low cost, small size and high sensitivity, which is an advantage for biomedical applications. In this paper,silicon nanowire was proposed to be used as the piezoresistors due to the high sensitivity [1][2].The sensors were designed, and characterized for the use of medical devices for pressure monitoring. The pressure sensor size is 2mm x 2mm with embedded SiNWs of 90nm x150nm been fabricated. Additionally, the sensitivity of 0.0024 Pa-1 pressure sensor has been demonstrated.

Low Power and High Sensitivity MOSFET-Based Pressure Sensor

2012 ◽  
Vol 29 (8) ◽  
pp. 088501 ◽  
Author(s):  
Zhao-Hua Zhang ◽  
Tian-Ling Ren ◽  
Yan-Hong Zhang ◽  
Rui-Rui Han ◽  
Li-Tian Liu
Keyword(s):  
Low Power ◽  
Pressure Sensor ◽  
High Sensitivity

A Low-Noise, Low-Power, Wide Dynamic Range Logarithmic Amplifier for Biomedical Applications

2018 ◽  
Vol 27 (07) ◽  
pp. 1850104 ◽  
Author(s):  
Yuwadee Sundarasaradula ◽  
Apinunt Thanachayanont
Keyword(s):  
Low Power ◽  
Biomedical Applications ◽  
Dynamic Range ◽  
Supply Voltage ◽  
Low Noise ◽  
Power Supply Voltage ◽  
Wide Dynamic Range ◽  
Dc Offset ◽  
Limiting Amplifier ◽  
Logarithmic Amplifier

This paper presents the design and realization of a low-noise, low-power, wide dynamic range CMOS logarithmic amplifier for biomedical applications. The proposed amplifier is based on the true piecewise linear function by using progressive-compression parallel-summation architecture. A DC offset cancellation feedback loop is used to prevent output saturation and deteriorated input sensitivity from inherent DC offset voltages. The proposed logarithmic amplifier was designed and fabricated in a standard 0.18[Formula: see text][Formula: see text]m CMOS technology. The prototype chip includes six limiting amplifier stages and an on-chip bias generator, occupying a die area of 0.027[Formula: see text]mm2. The overall circuit consumes 9.75[Formula: see text][Formula: see text]W from a single 1.5[Formula: see text]V power supply voltage. Measured results showed that the prototype logarithmic amplifier exhibited an 80[Formula: see text]dB input dynamic range (from 10[Formula: see text][Formula: see text]V to 100[Formula: see text]mV), a bandwidth of 4[Formula: see text]Hz–10[Formula: see text]kHz, and a total input-referred noise of 5.52[Formula: see text][Formula: see text]V.

High-Count Rate, Low Power and Low Noise Single Electron Readout ASIC in 65nm CMOS Technology

2021 ◽  
Author(s):  
Matthew Al Disi ◽  
Alireza Mohammad Zaki ◽  
Qinwen Fan ◽  
Stoyan Nihtianov
Keyword(s):  
Low Power ◽  
Count Rate ◽  
Cmos Technology ◽  
Low Noise ◽  
Single Electron ◽  
High Count ◽  
High Count Rate
Sign in / Sign up

Export Citation Format

Share Document