scholarly journals Investigations of Electron Properties of Carbon Nanotubes Decorated with Platinum Nanoparticles with Their Varying Fraction

2016 ◽  
Vol 2016 ◽  
pp. 1-8 ◽  
Author(s):  
Anna Dobrzańska-Danikiewicz ◽  
Dariusz Łukowiec ◽  
Jerzy Kubacki
Keyword(s):  
Carbon Nanotubes ◽  
Chemical Composition ◽  
Platinum Nanoparticles ◽  
Photoelectron Spectroscopy ◽  
Qualitative And Quantitative Analysis ◽  
X Ray ◽  
Qualitative And Quantitative ◽  
The Core ◽  
Wide Range ◽  
Varying Mass

The paper presents the outcomes of investigations into electron properties and a qualitative and quantitative analysis of the chemical composition of unmodified carbon nanotubes with comparison to nanotubes decorated with platinum nanoparticles. The fabricated nanocomposite materials of the CNT-Pt type differed in a varying mass concentration of platinum nanoparticles (5, 10, and 20% of Pt). X-ray photoelectron spectroscopy (XPS) was employed to examine the structure and to analyse chemical composition. Survey spectra measurements within a wide range of the binding energy of 0–1400 eV were performed in the first phase of the investigations. The core lines of C1s carbon, Pt4f platinum, and O1s oxygen and a valence band were then measured. The chemical composition of the studied materials was determined based on the measured spectra of the core lines. The purpose of the investigations is to determine the effect of platinum nanoparticles on the structure and electron properties of the fabricated CNT-Pt nanocomposites.

X-ray photoelectron spectroscopy characterization of aerosol particles in Antarctica

2015 ◽  
Vol 27 (5) ◽  
pp. 493-499 ◽  
Author(s):  
Simona Rella ◽  
Cosimino Malitesta
Keyword(s):  
Photoelectron Spectroscopy ◽  
Surface Characterization ◽  
Chemical Elements ◽  
Aerosol Particles ◽  
Qualitative And Quantitative Analysis ◽  
Surface Enrichment ◽  
X Ray ◽  
Qualitative And Quantitative

AbstractQualitative and quantitative analysis of surface species on size-segregated atmospheric particulate collected in Antarctica during the 2010–11 summer was performed by X-ray photoelectron spectroscopy (XPS). This represents the first example of surface characterization of Antarctic aerosols. The size class with particle cut-off diameter of 3 μm was richest in terms of chemical elements. Peculiar findings of the application included detection of Ca (possibly surface-segregated) and surface enrichment of Mg. The determination of nitrate, ammonium and sulphate species on collection filters provides evidence for a possible advantage of XPS over more laborious techniques (e.g. ion chromatography). The presence of these species is in reasonable agreement with other recent reports from Antarctica.

scholarly journals Effect of Cellulose Nanocrystals on the Coating of Chitosan Nanocomposite Film Using Plasma-Mediated Deposition of Amorphous Hydrogenated Carbon (a–C:H) Layers

2020 ◽  
Vol 6 (3) ◽  
pp. 51 ◽  
Author(s):  
Torben Schlebrowski ◽  
Zineb Kassab ◽  
Mounir El Achaby ◽  
Stefan Wehner ◽  
Christian B. Fischer
Keyword(s):  
Chemical Composition ◽  
Cellulose Nanocrystals ◽  
Photoelectron Spectroscopy ◽  
Nanocomposite Film ◽  
Chemical Vapor ◽  
Good Alternative ◽  
Ex Situ ◽  
X Ray ◽  
Wide Range ◽  
Amorphous Hydrogenated Carbon

The substitution of petroleum-based polymers with naturally derived biopolymers may be a good alternative for the conservation of natural fossil resources and the alleviation of pollution and waste disposal problems. However, in order to be used in a wide range of applications, some biopolymers’ properties should be enhanced. In this study, biocompatible, non-toxic, and biodegradable chitosan (CS) film and CS reinforced with 10 wt% of cellulose nanocrystals (CN–CS) were coated with amorphous hydrogenated carbon layers (a–C:H) of different thickness. To investigate the effect of the nano-reinforcement on the a–C:H layer applied, mild radio frequency plasma enhanced chemical vapor deposition (RF-PECVD) was used to coat the CS and its CN–CS bio-nanocomposite film. Both the surface characteristics and the chemical composition were analyzed. The surface morphology and wettability were examined by ex-situ atomic force microscopy (AFM) and contact angle measurements (CA), respectively. Hereby, the relationship between sp2/sp3 ratios on a macroscopic scale was also evaluated. For the investigation of the chemical composition, the surface sensitive synchrotron X-ray radiation techniques near edge X-ray absorption fine structure (NEXAFS) and X-ray photoelectron spectroscopy (XPS) as well as diffuse reflectance infrared Fourier transform spectroscopy (DRIFT) were used.

Highly active carbon nanotube–promoted Rh-Mn-Li/SiO2 catalysts for the synthesis of C2+ oxygenates from syngas

2021 ◽  
pp. 174751982098472
Author(s):  
Jun Yu ◽  
Ying Han ◽  
Guoqing Chen ◽  
Xiuzhen Xiao ◽  
Haifang Mao ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Photoelectron Spectroscopy ◽  
Co Hydrogenation ◽  
X Ray ◽  
Highly Active ◽  
Transmission Electron ◽  
Co Insertion ◽  
Temperature Programmed Surface Reaction ◽  
Temperature Programmed ◽  
Oxygenate Synthesis

The effect of carbon nanotubes on the catalytic properties of Rh-Mn-Li/SiO2 catalysts was investigated for CO hydrogenation. The catalysts were comprehensively characterized by means of X-ray power diffraction, N2 sorption, transmission electron microscope, H2–temperature-programmed reduction, CO–temperature-programmed desorption, temperature-programmed surface reaction, and X-ray photoelectron spectroscopy. The results showed that an appropriate amount of carbon nanotubes can be attached to the surface of the SiO2 sphere and can improve the Rh dispersion. Moderate Rh-Mn interaction can be obtained by doping with the appropriate amount of carbon nanotubes, which promotes the formation of strongly adsorbed CO and facilitates the progress of CO insertion, resulting in the increase in the selectivity of C2+ oxygenate synthesis.

scholarly journals Non-invasive sensing for food reassurance

The Analyst ◽  
2016 ◽  
Vol 141 (5) ◽  
pp. 1587-1610 ◽  
Author(s):  
Zou Xiaobo ◽  
Huang Xiaowei ◽  
Malcolm Povey
Keyword(s):  
Chemical Composition ◽  
Physicochemical Properties ◽  
Food Quality ◽  
Physical Principle ◽  
Quality Traits ◽  
X Ray ◽  
Main Food ◽  
Non Invasive ◽  
Wide Range ◽  
Nutritional Characteristics

The main food quality traits of interest using non-invasive sensing techniques are sensory characteristics, chemical composition, physicochemical properties, health-protecting properties, nutritional characteristics and safety. A wide range of non-invasive sensing techniques, from optical, acoustical, electrical, to nuclear magnetic, X-ray, biosensor, microwave and terahertz, are organized according to physical principle.

scholarly journals A Highly Sensitive Room Temperature CO2 Gas Sensor Based on SnO2-rGO Hybrid Composite

Materials ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 522
Author(s):  
Zhi Yan Lee ◽  
Huzein Fahmi bin Hawari ◽  
Gunawan Witjaksono bin Djaswadi ◽  
Kamarulzaman Kamarudin
Keyword(s):  
Electron Microscopy ◽  
Carbon Dioxide ◽  
Gas Sensor ◽  
Photoelectron Spectroscopy ◽  
Hybrid Composite ◽  
Room Temperature ◽  
Co2 Gas ◽  
X Ray ◽  
Wide Range ◽  
Co2 Gas Sensor

A tin oxide (SnO2) and reduced graphene oxide (rGO) hybrid composite gas sensor for high-performance carbon dioxide (CO2) gas detection at room temperature was studied. Since it can be used independently from a heater, it emerges as a promising candidate for reducing the complexity of device circuitry, packaging size, and fabrication cost; furthermore, it favors integration into portable devices with a low energy density battery. In this study, SnO2-rGO was prepared via an in-situ chemical reduction route. Dedicated material characterization techniques including field emission scanning electron microscopy (FESEM), high-resolution transmission electron microscopy (HRTEM), energy dispersive X-ray (EDX) spectroscopy, Raman spectroscopy, and X-ray photoelectron spectroscopy (XPS) were conducted. The gas sensor based on the synthesized hybrid composite was successfully tested over a wide range of carbon dioxide concentrations where it exhibited excellent response magnitudes, good linearity, and low detection limit. The synergistic effect can explain the obtained hybrid gas sensor’s prominent sensing properties between SnO2 and rGO that provide excellent charge transport capability and an abundance of sensing sites.

Multiwalled Carbon Nanotubes Covered with Cobalt (II) Phthalocyanine by In Situ Synthesis and its Electrochemical Sensing Performance towards DA and UA

2014 ◽  
Vol 809-810 ◽  
pp. 43-52
Author(s):  
Hua Hua Wang ◽  
Nan Li ◽  
Kai Li ◽  
Yuan Bu ◽  
Wen Le Dai ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Multiwalled Carbon Nanotubes ◽  
Photoelectron Spectroscopy ◽  
Simultaneous Detection ◽  
Thick Layer ◽  
Electrochemical Sensing ◽  
Multiwalled Carbon ◽  
X Ray ◽  
Platinum Particles

Multiwalled carbon nanotubes (MWCNTs) as an excellent supporter covered with a thick layer of cobalt phthalocyanine (CoPc) were prepared by in-situ synthesis. Platinum particles were adopted to enhance the conductivity of CoPc-MWCNTs. The final nanocomposite Pt-CoPc-MWCNTs was characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM). Strong aromatic π-π stacking between MWCNTs and CoPc made CoPc in-situ forming on MWCNTs. With homogeneous thickness of CoPc covered on the MWCNTs and Pt particles equally distributed, the nanocomposite was used as electrocatalyst. The electrochemical properties of the composite got researched by casting the dispersion of Pt-CoPc-MWCNTs on the glassy carbon electrode. Compared with other modified electrodes, Pt-CoPc-MWCNTs/GC electrode exhibited excellent electrochemical activity towards dopamine (DA) and uric acid (UA). Linear responses for DA and UA were obtained in the ranges of 5 to 170 μM and 5 to 100 μM, and limits of detection were 2.6 and 1.4 μM (S/N= 3), respectively. Simultaneous detection of DA and UA in the presence of ascorbic acid (AA) also displayed selective property, with no interference to each other.

scholarly journals Increased Electrical Conductivity of Carbon Nanotube Fibers by Thermal and Voltage Annealing

2021 ◽  
Vol 8 (1) ◽  
pp. 1
Author(s):  
Varun Shenoy Gangoli ◽  
Chris J. Barnett ◽  
James D. McGettrick ◽  
Alvin Orbaek White ◽  
Andrew R. Barron
Keyword(s):  
Carbon Nanotubes ◽  
Electrical Conductivity ◽  
Raman Spectroscopy ◽  
Photoelectron Spectroscopy ◽  
Separate Analysis ◽  
Sweet Spot ◽  
Electrical Conductor ◽  
X Ray ◽  
Resonant Raman ◽  
Carbon Nanotube Fibers

We report the effect of annealing, both electrical and by applied voltage, on the electrical conductivity of fibers spun from carbon nanotubes (CNTs). Commercial CNT fibers were used as part of a larger goal to better understand the factors that go into making a better electrical conductor from CNT fibers. A study of thermal annealing in a vacuum up to 800 °C was performed on smaller fiber sections along with a separate analysis of voltage annealing up to 7 VDC; both exhibited a sweet spot in the process as determined by a combination of a two-point probe measurement with a nanoprobe, resonant Raman spectroscopy, and X-ray photoelectron spectroscopy (XPS). Scaled-up tests were then performed in order to translate these results into bulk samples inside a tube furnace, with similar results that indicate the potential for an optimized method of achieving a better conductor sample made from CNT fibers. The results also help to determine the surface effects that need to be overcome in order to achieve this.

scholarly journals Graphitic Nitrogen in Carbon Catalysts Important for the Reduction of Nitrite Revealed by 15N NMR Spectroscopy at Natural Abundance

2020 ◽  
Author(s):  
Zheng Chen ◽  
Aleksander Jaworski ◽  
Jianhong Chen ◽  
Tetyana Budnyak ◽  
Ireneusz Szewczyk ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Reduction Reaction ◽  
Nitrite Reduction ◽  
15N Nmr ◽  
Carbon Catalyst ◽  
X Ray ◽  
Wide Range ◽  
Alkaline Conditions

Metal-free nitrogen-doped carbon is considered as a green functional material, but the structural determination of the atomic positions of nitrogen remains challenging. We recently demonstrated that directly-excited solid state <sup>15</sup>N NMR (ssNMR) spectroscopy is a powerful tool for the determination of such positions in an N-doped carbon at natural <sup>15</sup>N isotope abundance. Here we present a green chemistry approach to the synthesis of N-doped carbon using cellulose as precursor, and a study of the catalytic properties and atomic structures of the related catalyst. The N-doped carbon (NH<sub>3</sub>) was obtained by oxidation of cellulose with HNO<sub>3</sub> followed by ammonolysis at 800°C. It had a N content of 6.5 wt.% and a surface area of 557 m<sup>2 </sup>g<sup>–1</sup>, and <sup>15</sup>N ssNMR spectroscopy provided evidence for graphitic nitrogen besides of regular pyrrolic and pyridinic nitrogen. This structure determination enabled probing the role of graphitic nitrogen for electrocatalytic reactions, such as the hydrogen evolution reaction (HER), oxygen evolution reaction (OER), and nitrite reduction reaction. The N-doped carbon catalyst (NH<sub>3</sub>) had higher electrocatalytic activities in OER and HER under alkaline conditions and a higher activity for nitrite reduction, as compared with a catalyst prepared by carbonization of the HNO<sub>3</sub>-treated cellulose in N<sub>2</sub>. The electrocatalytic selectivity for nitrite reduction of the N-doped carbon catalyst (NH<sub>3</sub>) was directly related to the graphitic nitrogen functions. Complementary structural analysis by means of <sup>13</sup>C and <sup>1</sup>H ssNMR, scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, and low-temperature N<sub>2 </sub>adsorption were preformed and provided support to the findings. The results show that directly-excited <sup>15</sup>N ssNMR at natural <sup>15</sup>N abundance is generally capable to provide information on N-doped carbon materials, and it is expected that the approach can be applied to a wide range of solids with an intermediate amount of N atoms.

Sign in / Sign up

Export Citation Format

Share Document